TM Mini-Circuits System In Package Flat Gain Amplifier YSF-122+ The Big Deal: * Ultra Flat Gain Response: 0.2 dB over 800-1200 MHz * Excellent Combination of gain, P1dB, IP3 and NF * 50 Input and Output: no External Components Required CASE STYLE: DL1636 Product Overview: TM YSF-122+ is an advanced amplifier module in a Mini-Circuits System In Package . This module is fully matched to 50 in/out impedance and has built-in Input & Output DC block capacitors. It is enclosed in a 5 x 6 mm MCLP plastic package. The YSF-122+ uses E-PHEMT technology enabling it to work with a single positive supply voltage. Key Features Feature Advantages Superior Gain Flatness 0.2dB The YSF-122+ provides industry leading gain flatness over the full cellular communications L band (800-1200 MHz) making this ideal for use in applications where gainflatness and repeatability are critical performance requirements. High Gain The YSF-122+ is a two-stage design with internal feedback and bias to provide flat 20 dB nominal gain, supporting applications where a single gain block must overcome large system losses such as long cable runs and lossy components. Strong Combination of Performance The YSF-122+ provides a strong combination of performance parameters including high gain (20 dB), high IP3 (+37 dBm) and P1dB (+20 dBm) and low noise figures (3.4 dB) that are difficult to achieve in a single stage design and available only in the YSF amplifier series. Integrated Matching, DC Blocking and Bias in Small Package The YSF-122+ includes all support circuits including: Matching, Bias and DC Blocking, all integrated into a single 5x6mm package making the total footprint equal to or smaller than most solutions. Excellent Return Loss The YSF-122+ includes integrated input and output matching and bias circuits to make this amplifier a simple, complete drop-in solution. The matching circuits provide excellent output return loss (17dB), and are designed to give optimal P1dB and IP3 performance in a 50 environment. High Reverse Isolation With 30 dB of reverse isolation - the YSF-122+ is an ideal gain block for use in integrated systems to minimize VSWR interactions resulting from cascading highly reflective components such as sharp filters. Mini-Circuits (R) ISO 9001 ISO 14001 AS 9100 CERTIFIED P.O. Box 350166, Brooklyn, New York 11235-0003 (718) 934-4500 Fax (718) 332-4661 The Design Engineers Search Engine For detailed performance specs & shopping online see web site (R) Provides ACTUAL Data Instantly at minicircuits.com IF/RF MICROWAVE COMPONENTS Notes: 1. Performance and quality attributes and conditions not expressly stated in this specification sheet are intended to be excluded and do not form a part of this specification sheet. 2. Electrical specifications and performance data contained herein are based on Mini-Circuit's applicable established test performance criteria and measurement instructions. 3. The parts covered by this specification sheet are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, "Standard Terms"); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Page 1 Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits' website at www.minicircuits.com/MCLStore/terms.jsp. TM Mini-Circuits System In Package Flat Gain Amplifier 0.8-1.2 GHz Product Features * Matched 50-ohm surface mount amplifier * High gain, 20 dB typ. * Up to +20 dBm typ. output power * High IP3, +37 dBm * Low Noise Figure, 3.4 dB typ. * High directivity, 32 dB isolation * Internal Input & Output DC Block * Separate terminal for DC YSF-122+ CASE STYLE: DL1636 PRICE: $2.69 ea. QTY. (20) + RoHS compliant in accordance with EU Directive (2002/95/EC) Typical Applications * Cellular * Portable Wireless * Receivers & transmitters * Radar The +Suffix has been added in order to identify RoHS Compliance. See our web site for RoHS Compliance methodologies and qualifications. General Description TM YSF-122+ is an advanced amplifier module in a Mini-Circuits System In Package . This module is fully matched to 50 in/out impedance and has built-in Input & Output DC block capacitors. It is enclosed in a 5 x 6 mm MCLP plastic package. The YSF-122+ uses E-PHEMT* technology enabling it to work with a single positive supply voltage. simplified schematic and pad description 8 NC DC RF IN NC 1 Pad Number RF-IN 5 RF Input RF-OUT 3 RF Output DC 4 DC Supply GND Paddle NOT USED 1,2,6,7,8 6 5 NC RF IN PADDLE RF OUT Function 7 NC NC RF OUT DC IN 2 3 4 Description Connected to ground No internal connection *Enhancement mode Pseudomorphic High Electron Mobility Transistor Mini-Circuits (R) ISO 9001 ISO 14001 AS 9100 CERTIFIED P.O. Box 350166, Brooklyn, New York 11235-0003 (718) 934-4500 Fax (718) 332-4661 The Design Engineers Search Engine For detailed performance specs & shopping online see web site (R) Provides ACTUAL Data Instantly at minicircuits.com IF/RF MICROWAVE COMPONENTS Notes: 1. Performance and quality attributes and conditions not expressly stated in this specification sheet are intended to be excluded and do not form a part of this specification sheet. 2. Electrical specifications and performance data contained herein are based on Mini-Circuit's applicable established test performance criteria and measurement instructions. 3. The parts covered by this specification sheet are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, "Standard Terms"); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits' website at www.minicircuits.com/MCLStore/terms.jsp. REV. A M134205 YSF-122+ 110126 Page 2 TM Flat Gain Amplifier YSF-122+ Electrical Specifications(1) at 25C, Zo=50 unless noted Parameter Condition (MHz) Min. Frequency Range Typ. Max. Units 1200 MHz 800 800 Gain 18.1 20.1 22.1 1000 18.4 20.4 22.4 1200 18.3 20.3 22.3 Gain Flatness dB 0.2 800 Input Return Loss 1000 9.0 11.0 1200 dB 11.0 800 Output Return Loss dB 8.8 13.0 1000 11.0 15.0 1200 dB 17.3 Reverse Isolation 32.0 800 Output Power @1 dB compression dB 20.5 1000 18.5 20.5 1200 dBm 20.4 Output Power @ 3 dB compression 21.3 800 Output IP3 1000 Noise Figure dBm 37.0 31.0 36.0 1200 36.0 800 3.5 1000 3.4 1200 3.4 Device Operating Voltage 5 Device Operating Current 118 Device Current Variation vs. Temperature(2) Device Current Variation vs Voltage Thermal Resistance, junction-to-ground lead (3) dBm 4.4 dB 145 mA V 2 A/C 0.002 mA/mV 56 C/W Measured on Mini-Circuits Characterization test board TB-616+. See Characterization Test Circuit (Fig. 1) (2) D(+85C to -45C) (3) Thermal Resistance= Hot spot temperature - Ground lead temperature Power Dissipation (1) DC Current Histogram Absolute Maximum Ratings Parameter Ratings Units Operating Temperature(4) -40 to 85 C Storage Temperature -65 to 150 C DC Voltage on Pad 4 7 V Power Dissipation 1.5 W Input Power 21 dBm 155 150 145 140 135 130 125 120 115 110 105 100 95 90 Note: Permanent damage may occur if any of these limits are exceeded. These ratings are not intended for continuous normal operation. (4) Case is defined as ground paddle. USL DC Current (mA) USL=Upper Spec Limit Mini-Circuits (R) ISO 9001 ISO 14001 AS 9100 CERTIFIED P.O. Box 350166, Brooklyn, New York 11235-0003 (718) 934-4500 Fax (718) 332-4661 The Design Engineers Search Engine For detailed performance specs & shopping online see web site (R) Provides ACTUAL Data Instantly at minicircuits.com IF/RF MICROWAVE COMPONENTS Notes: 1. Performance and quality attributes and conditions not expressly stated in this specification sheet are intended to be excluded and do not form a part of this specification sheet. 2. Electrical specifications and performance data contained herein are based on Mini-Circuit's applicable established test performance criteria and measurement instructions. 3. The parts covered by this specification sheet are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, "Standard Terms"); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Page 3 Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits' website at www.minicircuits.com/MCLStore/terms.jsp. TM Flat Gain Amplifier YSF-122+ Characterization Test Circuit Vs (Supply Voltage) 4 3 5 RF-IN RF-OUT TB-616+ Fig 1. Block Diagram of Test Circuit used for characterization. (DUT soldered on Mini-Circuits Characterization Test Fixture TB-616+) Gain, Return loss, Output power at 1dB compression (P1 dB), Output IP3 (OIP3) and Noise Figure measured using Agilent's N5242A PNA-X microwave network analyzer. Conditions: 1. Gain: Pin= -25dBm 2. Output IP3 (OIP3): Two tones, spaced 10 MHz apart, 2.5 dBm/tone at output. Recommended Application Circuit (refer to evaluation board for PCB Layout and component values) Vs C1 4 RF-IN 3 5 RF-OUT Paddle Fig 2. Recommended Application Circuit Product Marking YSF index over pin 1 Mini-Circuits (R) ISO 9001 ISO 14001 AS 9100 CERTIFIED P.O. Box 350166, Brooklyn, New York 11235-0003 (718) 934-4500 Fax (718) 332-4661 The Design Engineers Search Engine For detailed performance specs & shopping online see web site (R) Provides ACTUAL Data Instantly at minicircuits.com IF/RF MICROWAVE COMPONENTS Notes: 1. Performance and quality attributes and conditions not expressly stated in this specification sheet are intended to be excluded and do not form a part of this specification sheet. 2. Electrical specifications and performance data contained herein are based on Mini-Circuit's applicable established test performance criteria and measurement instructions. 3. The parts covered by this specification sheet are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, "Standard Terms"); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Page 4 Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits' website at www.minicircuits.com/MCLStore/terms.jsp. TM Flat Gain Amplifier YSF-122+ Additional Detailed Technical Information additional information is available on our dash board. To access this information click here Data Table Performance Data Swept Graphs S-Parameter (S2P Files) Data Set (.zip file) Case Style DL1636 Plastic package, exposed paddle, lead finish: tin/silver/nickel Tape & Reel F68 Standard quantities available on reel 7" reels with 20, 50, 100, 200, 500 or 1K devices. 13" reels with 2K, or 4K devices. Suggested Layout for PCB Design PL-352 Evaluation Board TB-616-2+ Environmental Ratings ENV08T1 ESD Rating Human Body Model (HBM): Class 1A in accordance with ANSI/ESD STM 5.1 - 2001 Machine Model (MM): Class M1 (25V) in accordance with ANSI/ESD STM5.2-1999 Attention Observe precautions for handling electrostatic sensitive devices MSL Rating Moisture Sensitivity: MSL1 in accordance with IPC/JEDEC J-STD-020D MSL Test Flow Chart Start Visual Inspection Electrical Test SAM Analysis Reflow 3 cycles, 260C Soak 85C/85RH 168 hours Bake at 125C, 24 hours Visual Inspection Electrical Test SAM Analysis Mini-Circuits (R) ISO 9001 ISO 14001 AS 9100 CERTIFIED P.O. Box 350166, Brooklyn, New York 11235-0003 (718) 934-4500 Fax (718) 332-4661 The Design Engineers Search Engine For detailed performance specs & shopping online see web site (R) Provides ACTUAL Data Instantly at minicircuits.com IF/RF MICROWAVE COMPONENTS Notes: 1. Performance and quality attributes and conditions not expressly stated in this specification sheet are intended to be excluded and do not form a part of this specification sheet. 2. Electrical specifications and performance data contained herein are based on Mini-Circuit's applicable established test performance criteria and measurement instructions. 3. The parts covered by this specification sheet are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, "Standard Terms"); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Page 5 Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits' website at www.minicircuits.com/MCLStore/terms.jsp.