LM185-1.2QML LM185-1.2QML Micropower Voltage Reference Diode Literature Number: SNVS384 LM185-1.2QML Micropower Voltage Reference Diode General Description The LM185-1.2 is a micropower 2-terminal band-gap voltage regulator diodes. Operating over a 10A to 20mA current range, it features exceptionally low dynamic impedance and good temperature stability. On-chip trimming is used to provide tight voltage tolerance. Since the LM185-1.2 band-gap reference uses only transistors and resistors, low noise and good long term stability result. Careful design of the LM185-1.2 has made the device exceptionally tolerant of capacitive loading, making it easy to use in almost any reference application. The wide dynamic operating range allows its use with widely varying supplies with excellent regulation. The extremely low power drain of the LM185-1.2 makes it useful for micropower circuitry. This voltage reference can be used to make portable meters, regulators or general purpose analog circuitry with battery life approaching shelf life. Further, the wide operating current allows it to replace older references with a tighter tolerance part. Features n n n n Operating current of 10A to 20mA 1 maximum dynamic impedance (typical) Low temperature coefficient Low voltage reference - 1.235V Ordering Information NS Part Number JAN Part Number NS Package Number LM185E-1.2/883 5962-87594012A E20A 20LD LCC LM185H-1.2-SMD 5962-8759401XA H02A 2 LD T0-46 LM185H-1.2-QV 5962-8759401VXA H02A 2 LD T0-46 LM185WG-1.2/883 5962-8759401YA WG10A LM185BYH-1.2-SMD 5962-8759405XA H02A LM185WG-1.2-QV 5962-8759401VYA WG10A Package Description 10LD Ceramic SOIC 2 LD T0-46 10LD Ceramic SOIC Connection Diagrams Hermetic Leadless Chip Carrier (E) TO-46 Metal Can Package (H) 20156106 20156135 See NS Package Number E20A (c) 2005 National Semiconductor Corporation DS201561 Bottom View See NS Package Number H02A www.national.com LM185-1.2QML Micropower Voltage Reference Diode October 2005 LM185-1.2QML Connection Diagrams (Continued) Ceramic SOIC (WG) 20156134 See NS Package Number WG10A Schematic Diagram 20156107 www.national.com 2 LM185-1.2QML Absolute Maximum Ratings (Note 1) Reverse Current 30mA Forward Current 10mA -55C TA +125C Operating Temperature Range Maximum Junction Temperature (TJmax) (Note 2) +150C -55C TA +150C Storage Temperature Lead Temperature (Soldering 10 Seconds) Ceramic SOIC 260C TO-46 package 300C 20LD LCC package 300C Thermal Resistance JA Metal Can (Still Air) 300C/W Metal Can (500LF / Min Air Flow) 139C/W 20LD LCC (Still Air) 100C/W 20LD LCC (500LF / Min Air Flow) 73C/W Ceramic SOIC (Still Air) 194C/W Ceramic SOIC (500LF / Min Air Flow) 128C/W JC Metal Can 57C/W 20LD LCC 25C/W Ceramic SOIC 23C/W Package Weight (Typical) Metal Can TBD 20LD LCC TBD Ceramic SOIC 210mg ESD Tolerance (Note 3) 4KV Quality Conformance Inspection Mil-Std-883, Method 5005 - Group A Subgroup Description 1 Static tests at Temp C 25 2 Static tests at 125 3 Static tests at -55 4 Dynamic tests at 25 5 Dynamic tests at 125 6 Dynamic tests at -55 7 Functional tests at 25 8A Functional tests at 125 8B Functional tests at -55 9 Switching tests at 25 10 Switching tests at 125 11 Switching tests at -55 12 Settling time at 25 13 Settling time at 125 14 Settling time at -55 3 www.national.com LM185-1.2QML LM185-1.2 Electrical Characteristics DC Parameters Symbol VRef Parameter Reverse Breakdown Voltage Conditions Notes VF Forward Bias Voltage Max Units Subgroups IR = 10A 1.223 1.247 V 1 IR = 20A 1.205 1.26 V 2, 3 IR = 1mA 1.223 1.247 V 1 1.205 V 2, 3 IR = 20mA VRef / IR Reverse Breakdown Voltage Change with Current Min 10A IR 1mA 1.26 1.223 1.247 V 1 1.205 1.26 V 2, 3 -1.0 1.0 mV 1 2, 3 20A IR 1mA -1.5 1.5 mV 1mA IR 20mA -10.0 10.0 mV 1 -20.0 20.0 mV 2, 3 -1.0 -0.4 V 1 IF = 2mA DC Drift Parameters Delta calculations performed on QMLV devices at group B , subgroup 5, unless otherwise specified on the IPI. Symbol VR Parameter Reverse Breakdown Voltage Conditions Notes Min Max Units Subgroups IR = 10A -0.01 0.01 V 1 IR = 20mA -0.01 0.01 V 1 Min Max Units Subgroups V 1 2, 3 LM185BY-1.2 Electrical Characteristics DC Parameters Symbol VRef Parameter Reverse Breakdown Voltage Conditions Notes IR = 10A 1.223 1.247 IR = 20A 1.205 1.26 V IR = 1mA 1.223 1.247 V 1 1.205 1.26 V 2, 3 1.223 1.247 V 1 2, 3 IR = 20mA VRef / IR Reverse Breakdown Voltage Change with Current 1.205 1.26 V 10A IR 1mA -1.0 1.0 mV 1 20A IR 1mA -1.5 1.5 mV 2, 3 1mA IR 20mA VF Forward Bias Voltage TC Temperature Coefficient IF = 2mA (Note 4) -10.0 10.0 mV 1 -20.0 20.0 mV 2, 3 -1.0 -0.4 V 1 50 PPM/C 2, 3 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), JA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA)/JA or the number given in the Absolute Maximum Ratings, whichever is lower. Note 3: Human body model, 1.5K in series with 100pF. Note 4: The average temperature coefficient is defined as the maximum deviation of reference voltage, at all measured temperatures between the operating TMin & TMax, divided by (TMax - TMin). The measured temperatures (TMeasured) are -55C, 25C, & 125C or VRef / (TMax - TMin) www.national.com 4 LM185-1.2QML Typical Performance Characteristics Reverse Characteristics Reverse Characteristics 20156113 20156114 Temperature Drift of 3 Representative Units Forward Characteristics 20156116 20156115 Reverse Dynamic Impedance Reverse Dynamic Impedance 20156118 20156117 5 www.national.com LM185-1.2QML Typical Performance Characteristics (Continued) Noise Voltage Filtered Output Noise 20156120 20156119 Response Time 20156121 Typical Applications Reference from 1.5V Battery Wide Input Range Reference 20156123 20156108 Micropower Reference from 9V Battery 20156122 www.national.com 6 (Continued) Precision 1A to 1mA Current Sources Micropower* 5V Regulator 20156126 20156124 *IQ . 30A Micropower* 10V Reference 20156127 20156125 *IQ .20A standby current 7 www.national.com LM185-1.2QML Typical Applications LM185-1.2QML Typical Applications (Continued) METER THERMOMETERS Centigrade Thermometer 0C-100C Thermometer 20156101 20156128 Calibration Calibration 1. Short LM385-1.2, adjust R3 for IOUT= temp at 1A/K 1. Adjust R1 so that V1 = temp at 1mV/K 2. Remove short, adjust R2 for correct reading in centigrade 2. Adjust V2 to 273.2mV IQ at 1.3V.500A IQ for 1.3V to 1.6V battery volt- IQ at 1.6V.2.4mA age = 50A to 150A Micropower Thermocouple Cold Junction Compensator Lower Power Thermometer 20156129 *2N3638 or 2N2907 select for inverse HFE . 5 Select for operation at 1.3V IQ . 600A to 900A 0F-50F Thermometer 20156131 Adjustment Procedure 1. Adjust TC ADJ pot until voltage across R1 equals Kelvin temperature multiplied by the thermocouple Seebeck coefficient. 2. Adjust zero ADJ pot until voltage across R2 equals the thermocouple Seebeck coefficient multiplied by 273.2. Thermocouple Type R1 R2 Voltage Voltage Coefficient () () Seebeck Across R1 Across R2 @ 25C (mV) (V/C) (mV) 20156130 Calibration 1. Short LM385-1.2, adjust R3 for IOUT= temp at 1.8A/K 2. Remove short, adjust R2 for correct reading in F Typical supply current 50A www.national.com 8 J 52.3 5231.24k 15.60 T 42.8 432 1k 12.77 14.32 11.78 K 40.8 412953 12.17 11.17 S 6.4 63.4150 1.908 1.766 Released 10/07/05 Revision A Section Originator New Release, Corporate format L. Lytle 9 Changes 2 MDS data sheets converted into one Corp. data sheet format. MNLM185-1.2-X Rev 2A3 and MNLM185BY-1.2-X Rev 0B0 data sheets will be archived. www.national.com LM185-1.2QML Revision History Section LM185-1.2QML Physical Dimensions inches (millimeters) unless otherwise noted TO-46 Metal Can Package (H) NS Package Number H02A Leadless Chip Carrier Package (E) NS Package Number E20A www.national.com 10 LM185-1.2QML Micropower Voltage Reference Diode Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Ceramic SOIC Package (WG) NS Package Number WG10A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated