Dual Primary/Dual Secondary Transformers ! WARNING INPUT: OUTPUT: ELECTROCUTION HAZARD Disconnect electric power to system at main fuse or circuit breaker box before servicing. Failure to do so could result in death or serious injury. INSULATION RATING: TEMPERATURE RISE: DIELECTRIC STRENGTH: FIRE HAZARD Do not exceed transformer ratings. Higher voltage may damage control and could cause personal injury or property damage. AGENCY STANDARDS: FILE NUMBERS: Class A (105C) 65C Max. rise over 40C Max. ambient 1500 VRMS UL Recognized to UL 506 E68100 NOTES: 1. All dimensions in inches, unless otherwise specified. 2. All dimensions .062, unless otherwise specified. 3. Solder Lug termination. D MAX 1 2 H MAX 115 / 230VAC, 50/60Hz See Output Amp rating & VA Capacity in table below 3 4 MW .188 DIA. .032 (2 HOLES) 5 W MAX D MAX 1 6 2 7 3 8 H MAX 4 FIGURE 1 MW D MAX W MAX .188 DIA. .032 (2 HOLES) FIGURE 2 5 H MAX 1 6 2 7 3 8 4 MW MD W MAX MS .031 4 PLACES FIGURE 3 STANCOR Output from two Secondary Windings Part Dim s. Schem atic V.A. Individual Parallel Series Num ber Fig. Diagram Cap. Volts Am ps Volts Am ps Volts Am ps P-6375 1 2 12 6 @ 1.0 6 @ 2.0 12 @ 1.0 P-6376 1 2 24 6 @ 2.0 6 @ 4.0 12 @ 2.0 P-6377 2 1 48 12 @ 2.0 12 @ 4.0 24 @ 2.0 P-6378 3 1 96 12 @ 4.0 12 @ 8.0 24 @ 4.0 P-6379 3 1 192 12 @ 8.0 12 @ 16.0 24 @ 8.0 P-8615 1 2 12 24 @ .25 24 @ .50 48 @ .25 P-8616 1 2 24 24 @ .50 24 @ 1.0 48 @ .50 P-8617 2 1 48 24 @ 1.0 24 @ 2.0 48 @ 1.0 P-8618 3 1 96 24 @ 2.0 24 @ 4.0 48 @ 2.0 P-8619 3 1 192 24 @ 4.0 24 @ 8.0 48 @ 4.0 Dim ensions - Inches H W D MW MD MS WT. Lbs. 2.44 2.75 3.19 3.56 4.25 2.44 2.75 3.19 3.56 4.25 2.94 3.19 3.69 2.88 3.44 2.94 3.19 3.69 2.88 3.44 1.88 2.13 2.38 3.19 3.62 1.88 2.13 2.38 3.19 3.62 2.38 2.81 3.13 2.25 2.75 2.38 2.81 3.13 2.25 2.75 2.31 3.13 2.31 3.13 .187 X .312 .203 X .500 .187 X .312 .203 X .500 1.0 1.5 2.5 4.2 8.0 1.0 1.5 2.5 4.2 8.0 PART NO. 37-6260B www.stancor.com Replaces 37-6260A 0741