HD-LINX TM GS1545 HDTV Serial Digital Equalizing Receiver DATA SHEET DESCRIPTION * SMPTE 292M compliant The GS1545 is a high performance integrated Equalizing Receiver designed for HDTV component signals, conforming to the SMPTE 292M standard. The GS1545 includes adjustment free adaptive cable equalization, clock and data recovery, and serial to parallel conversion. * 1.485 and 1.485/1.001Gb/s operation * integrated adaptive cable equalizer * integrated adjustment-free reclocker * 1:20 serial to parallel conversion The Equalizer stage features DC restoration for immunity to the DC content in pathological test patterns. * selectable reclocked serial output * analog/digital input MUX The Clock and Data Recovery stage was designed to automatically recover the embedded clock signal and re-time the data from SMPTE 292M compliant digital video signals. There is also a selectable reclocked serial data output and the ability to bypass the reclocker stage. * carrier detect * LOCK detect * input jitter indicator (IJI) * cable length indication A unique feature, Input Jitter Indicator (IJI), is included for robust system design. This feature is used to indicate excessive input jitter before the chip mutes the outputs. * maximum cable length adjust * 20 bit output * 74.25MHz or 74.25/1.001MHz clock output The Serial to Parallel conversion stage provides 1:20 S/P conversion * Pb-free and Green * single +5.0V power supply The GS1545 uses the GO1515 external VCO connected to the internal PLL circuitry to achieve ultra low noise PLL performance. * minimal component count for HD SDI receive solutions APPLICATIONS SMPTE 292M Serial Digital Interfaces for Video Cameras, Camcorders, VTRs, Signal Generators, Portable Equipment, and NLEs. ORDERING INFORMATION PART NUMBER PACKAGE TEMPERATURE Pb-FREE AND GREEN GS1545-CQR 128 pin MQFP 0C to 70C No GS1545-CQRE3 128 pin MQFP 0C to 70C Yes DDOint SDI SDI EQUALIZER CORE DDOint ANALOGDIGITAL MUX & BUFFER RECLOCKER CORE S/P CONVERTER DATA_OUT[19:0] PCLK_OUT BUFFER DDO DDO DDI DDI_VTT DDI (opt) A/D DDO_EN SIMPLIFIED BLOCK DIAGRAM Revision Date: June 2004 Document No. 522 - 28 - 05 GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: info@gennum.com www.gennum.com GS1545 FEATURES GO1515 CD MCLADJ SDI LFS LFS CABLE LENGTH INDICATOR MAXIMUM CABLE LENGTH ADJUST CARRIER DETECT EQ CORE PLCAP PLCAP IJI CHARGE PUMP PHASE LOCK LOGIC PLL_LOCK GS1545 SDI LFA CLI DC RESTORE VCO PHASE DETECTOR BUFFER PCLK_OUT S/P CONVERTER CORE AGC DATA_OUT[19:0] MUTE EQUALIZER CORE DDOint+ DDOintBYPASS MUX BUFFER ANALOGDIGITAL MUX & BUFFER DDO DDO RECLOCKER CORE DDI DDI_VTT DDI (opt) A/D BYPASS DDO_EN FUNCTIONAL BLOCK DIAGRAM ABSOLUTE MAXIMUM RATINGS TA = 25C, unless otherwise shown. PARAMETER VALUE Supply Voltage (VS) Input Voltage Range (any input) Operating Temperature Range Storage Temperature Range 5.5V VEE - 0.5 < VIN < VCC+ 0.5 0C TA 70C -40C TS 150C Power Dissipation (VCC = 5.25V) 2.1W Lead Temperature (soldering 10 seconds) 260C Input ESD Voltage 1000V Junction Temperature 125C 2 of 19 GENNUM CORPORATION 522 - 28 - 05 DC ELECTRICAL CHARACTERISTICS VCC = 5V, VEE = 0V, TA = 0C to 70C unless otherwise shown, Data Rate = 1.485Gb/s. PARAMETER CONDITIONS SYMBOL MIN TYP MAX UNITS TEST LEVEL Operating range VCC 4.75 5.00 5.25 V 3 Power Consumption VCC = 5; TA = 25C PD - 1270 1535 mW 5 Supply Current VCC = 5 IS - 235 295 mA 1 VCM 3.4 3.9 4.30 V 5 Output CM Voltage (DDO, DDO) Input DC Voltage (DDI, DDI) internal bias voltage 3.7 4.0 4.2 V 1 Input DC Voltage (SDI, SDI) internal bias voltage 2.4 2.65 2.80 V 1 Serial Inputs (DDI, DDI) Differential mode VSID 100 - 800 mV 3 VCM 2.5+VSID/2 - VCC-VSID/2 V 3 VCC = 5, TA = 25C VIH 2.0 - - V 3 Low Level Input Voltage (A/D, BYPASS) VCC = 5, TA = 25C VIL - - 0.8 V 3 High Level Output Voltage VCC = 5, ISOURCE = 1.0mA VOH 2.4 - 3.0 V 1 VCC = 5, ISINK = 1.0mA VOL - - 0.4 V 1 High Level Output Voltage (PLL_LOCK) VCC = 5, ISOURCE = 200A VOH 2.4 3.0 - V 1 Low Level Output Voltage VCC = 5, ISINK = 500A VOL - - 0.4 V 1 ISINK = 500A VOL - - 0.4 V 1 2.9 3.2 3.6 V 3 1.0 1.4 2.3 V 3 3.4 4.1 4.3 V 3 2.9 3.1 3.4 V 3 TA = 25C Common mode TA = 25C High Level Input Voltage (A/D, BYPASS) (D[19:0], PCLK) Low Level Output Voltage (D[19:0], PCLK) (PLL_LOCK) Low Level Output Voltage (CD) CLI DC Voltage 1 meter, 800mV p-p Input TA = 25C CLI DC Voltage 120 meters, Belden 1694a (max cable length) TA = 25C MCLADJ DC Voltage 1 meter, 800mV p-p Input TA = 25C MCLADJ DC Voltage 120 meters, 800mV p-p Input (max cable length) TA = 25C TEST LEVELS 1. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges. 2. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges using correlated test. 3. Production test at room temperature and nominal supply voltage. 4. QA sample test. 5. Calculated result based on Level 1,2, or 3. 6. Not tested. Guaranteed by design simulations. 7. Not tested. Based on characterization of nominal parts. 8. Not tested. Based on existing design/characterization data of similar product. 9. Indirect test. 3 of 19 GENNUM CORPORATION 522 - 28 - 05 GS1545 Positive Supply Voltage AC ELECTRICAL CHARACTERISTICS - RECLOCKER STAGE VCC = 5V, TA = 25C PARAMETER CONDITIONS SYMBOL MIN TYP MAX UNITS TEST LEVEL BRSDI 1.485/1.001 1.485 - Gb/s 3 JTOL 0.5 0.6 - UI 9 SMPTE 292M Serial Input - Jitter Tolerance Sinewave Modulation (p - p) Phase Lock Time Asynchronous Loop bandwidth approximately 1.4MHz @ 0.2 UI input jitter modulation (LBCONT floating). TALOCK - 120 145 ms 7 Phase Lock Time - Synchronous Loop bandwidth approximately 1.4MHz @ 0.2 UI input jitter modulation (LBCONT floating). TSLOCK - 2 3.2 s 7 Carrier Detect Response Time Loop bandwidth approximately 1.4MHz @ 0.2 UI input jitter modulation (LBCONT floating). - 12 14 ms 7 Phase Lock/Unlock Time Loop bandwidth approximately 1.4MHz @ 0.2 UI input jitter modulation (LBCONT floating). 80 - - s 7 (1nF PLCAP) Digital Data Output (DDO) - Signal Swing VDDO 355 400 480 mV 1 Digital Data Output (DDO) - tR-DDO, tF-DDO - 160 - ps 7 - 30 - ps 7 - 10 - ps 9 1.2 1.4 1.5 MHz 7 - - 0.1 dB 7 Rise and Fall Time Digital Data Output (DDO) - Rise and Fall Time Mismatch Digital Data Output (DDO) - Intrinsic Jitter Loop bandwidth (RMS Jitter for clean PRN 2 input on DDI/DDI inputs) 23 -1 tIJ @ 0.2UI jitter modulation LBCONT floating Jitter peaking TEST LEVELS 1. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges. 2. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges using correlated test. 3. Production test at room temperature and nominal supply voltage. 4. QA sample test. 5. Calculated result based on Level 1,2, or 3. 6. Not tested. Guaranteed by design simulations. 7. Not tested. Based on characterization of nominal parts. 8. Not tested. Based on existing design/characterization data of similar product. 9. Indirect test. 4 of 19 GENNUM CORPORATION 522 - 28 - 05 GS1545 Serial Input - Data Rate AC ELECTRICAL CHARACTERISTICS - EQUALIZER STAGE VCC = 5V, TA = 25C PARAMETER Equalization CONDITIONS SYMBOL Belden 1694A Input Resistance (SDI, SDI) CIN TYP MAX UNITS TEST LEVEL - 110 - m 3 - 3.2 - k 7 - 2.0 - pF 7 AC ELECTRICAL CHARACTERISTICS - SERIAL TO PARALLEL STAGE VCC = 5V, TA = 25C CONDITIONS SYMBOL MIN TYP MAX UNITS TEST LEVEL SMPTE 292M PCLK_OUT 74.25/1.001 74.25 - MHz 3 Clock Pulse Width Low 15pF load tPWL 7 - 6.1 ns 7 Clock Pulse Width High 15pF load tPWH 6 - 6.4 ns 7 Output signal Rise/Fall time 15pF load tr, tf - 2.70 3.60 ns 7 Output Signal Rise/Fall Time Mismatch 15pF load trfm - 1.00 1.60 ns 7 Output Setup Time 15pF load tOD 5 5.5 - ns 7 Output Hold Time 15pF load tOH 6.2 7.1 - ns 7 PARAMETER Parallel Output Clock Frequency TEST LEVELS 1. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges. 2. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges using correlated test. 3. Production test at room temperature and nominal supply voltage. 4. QA sample test. 5. Calculated result based on Level 1,2, or 3. 6. Not tested. Guaranteed by design simulations. 7. Not tested. Based on characterization of nominal parts. 8. Not tested. Based on existing design/characterization data of similar product. 9. Indirect test. 5 of 19 GENNUM CORPORATION 522 - 28 - 05 GS1545 Input Capacitance (SDI, SDI) MIN 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 NC 65 38 NC NC 66 37 NC NC 67 36 PCLK_VEE NC 68 35 PCLK_VCC NC 69 34 PCLK_OUT NC 70 33 SP_VEE NC 71 32 SP_VEE LFA_VCC 72 31 SP_VCC LFA 73 30 SP_VCC LBCONT 74 29 NC LFA_VEE 75 28 NC DFT_VEE 76 27 NC NC 77 26 NC NC 78 25 NC DM 79 24 NC DM 80 23 NC LFS 81 22 NC NC 82 21 DDO_VCC NC 83 20 DDO_EN NC 84 19 DDO_VEE LFS 85 18 DDO IJI 86 17 DDO NC 87 16 EQO_VCC NC 88 15 NC VCO 89 14 NC NC 90 13 EQO_VEE VCO 91 12 CD NC 92 11 NC PLCAP 93 10 NC NC 94 9 NC NC 95 8 NC PLCAP 96 7 CLI NC 97 6 NC PLL_LOCK 98 5 MCLADJ NC 99 4 NC NC 100 3 NC NC 101 2 NC NC 102 1 NC GENNUM CORPORATION GS1545 TOP VIEW 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 GS1545 NC NC BYPASS DDI_VTT NC DDI DDI PD_VCC A/D PDSUB_VEE PD_VEE NC NC NC EQI_VCC NC NC EQI_VEE NC SDI NC SDI NC EQI_VEE NC NC DATA_OUT[19] DATA_OUT[18] DATA_OUT[17] DATA_OUT[16] DATA_OUT[15] DATA_OUT[14] NC NC DATA_OUT[13] DATA_OUT[12] DATA_OUT[11] DATA_OUT[10] NC NC DATA_OUT[9] DATA_OUT[8] DATA_OUT[7] DATA_OUT[6] DATA_OUT[5] DATA_OUT[4] DATA_OUT[3] DATA_OUT[2] DATA_OUT[1] DATA_OUT[0] NC NC PIN CONNECTIONS 6 of 19 522 - 28 - 05 PIN DESCRIPTIONS NUMBER LEVEL TYPE NC DESCRIPTION No Connect. Leave these pins floating. GS1545 1, 2, 3, 4, 6, 8, 9, 10, 11, 14, 15, 22, 23, 24, 25, 26, 27, 28, 29, 37, 38, 39, 40, 51, 52, 57, 58, 65, 66, 67, 68, 69, 70, 71, 77, 78, 82, 83, 84, 87, 88, 90, 92, 94, 95, 97, 99, 100, 101, 102, 103, 104, 107, 114, 115, 116, 118, 119, 121, 123, 125, 127, 128 SYMBOL 5 MCLADJ Analog Input Control Signal Input. Adjusts the maximum amount of cable for the equalizer (from 0m to the maximum cable length). Normally the output is muted (latched to the last state) when the set maximum cable length is exceeded. To achieve maximum cable length, this pin should be left open (floating). 7 CLI Analog Output Status Control Signal. The Cable Length Indication (CLI) signal provides approximate voltage representation of the amount of cable being equalized. 12 CD Digital Output Status Signal. The Carrier Detect indicator is used as an output status signal. When the CD output is low, the carrier is present and the data output is active. When the CD output is high, the carrier is not present and the data output is muted (latched to the last state). This indicates that the maximum cable length as set by MCLADJ has been reached. 13 EQO_VEE Power Input Negative Supply. Most negative power supply connection for Equalizer output buffer stage. 16 EQO_VCC Power Input Positive Supply. Most positive power supply connection for Equalizer output buffer stage. DDO, DDO ECL/PECL compatible Output 17, 18 Digital Data Output. Differential serial outputs. 50 pull up resistors are included on chip. Note that these outputs are not cable drivers. Ensure that the trace length between the GS1545 and the GS1508 Cable driver is kept to a minimum and that a PCB trace characteristic impedance of 50 is maintained between the GS1508 and the GS1545. 50 end termination is recommended. 19 DDO_VEE Power Input Negative Supply. Most negative power supply connection for serial data output stage. 20 DDO_EN Power Input Control Signal Input. Used to enable or disable the serial output stage. If a loop through function is not required, then this pin should be tied to the most positive power supply voltage. When DDO_EN is tied to the most negative power supply voltage, the DDO, DDO outputs are enabled. When DDO_EN is tied to the most positive power supply voltage, the DDO, DDO outputs are disabled. 21 30, 31 DDO_VCC Power Input Positive Supply. Most positive power supply connection for serial data output stage. SP_VCC Power Input Positive Supply. Most positive power supply connection for serial to parallel converter stage. 7 of 19 GENNUM CORPORATION 522 - 28 - 05 PIN DESCRIPTIONS (Continued) NUMBER SYMBOL LEVEL TYPE SP_VEE Power Input 34 PCLK_OUT TTL Output 35 PCLK_VCC Power Input Positive Supply. Most positive supply connection for parallel clock output stage. 36 PCLK_VEE Power Input Negative Supply. Most negative power supply connection for parallel clock output stage. DATA_OUT[19:0] TTL Output Parallel Data Output Bus. The device outputs a 20 bit parallel data stream running at 74.25 or 74.25/1.001MHz on DATA_OUT[19:0]. DATA_OUT[19] is the MSB and DATA_OUT[0] is the LSB. 72 LFA_VCC Power Input Positive Supply. Loop filter most positive power supply connection. 73 LFA Analog Output 74 LBCONT Analog Input Control Signal Input. Used to provide electronic control of Loop Bandwidth. 75 LFA_VEE Power Input Negative Supply. Loop filter most negative power supply connection. 76 DFT_VEE Power Input Most negative power supply connection - enables the jitter demodulator functionality. This pin should be connected to ground. If left floating, the DM function is disabled resulting in a current saving of 340A. 79, 80 DM, DM Analog Output 32, 33 Negative Supply. Most negative power supply connection for the parallel output stage. Output Clock. The device uses PCLK_OUT for clocking the output data stream from DATA_OUT[19:0]. This clock is also used to clock the data into the GS1500 HDTV Deformatter or GS1510 Deformatter. Control Signal Output. Control voltage for GO1515 VCO. Test Signal. Used for manufacturing test only. These pins must be floating for normal operation. LFS, LFS Analog Input 86 IJI Analog Output Status Signal Output. Approximates the amount of excessive jitter on the incoming DDI and DDI input. 89 VCO Analog Input Control Signal Input. Input pin is AC coupled to ground using a 50 transmission line. 91 VCO Analog Input Control Signal Input. Voltage controlled oscillator input. This pin is connected to the output pin of the GO1515 VCO. 81, 85 Loop Filter Connections. This pin must be connected to the GO1515 VCO output pin via a 50 transmission line. 93, 96 PLCAP, PLCAP Analog Input PLL_LOCK TTL Output 98 Control Signal Input. Phase lock detect time constant capacitor. Status Indicator Signal. This signal is a combination (logical AND) of the carrier detect and phase lock signals. When input is present and PLL is locked, the PLL_LOCK goes high and the outputs are valid. When the PLL_LOCK output is low the data output is muted (latched at the last state). PLL_LOCK is independent of the BYPASS signal. 105 BYPASS TTL Input Control Signal Input. Selectable input that controls whether the input signal is reclocked or passed through the chip. When BYPASS is high; the input signal is reclocked. When BYPASS is low; the input signal is passed through the chip and not reclocked. Muting does not effect bypassed signal. 8 of 19 GENNUM CORPORATION 522 - 28 - 05 GS1545 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 53, 54, 55, 56, 59, 60, 61, 62, 63, 64 DESCRIPTION PIN DESCRIPTIONS (Continued) NUMBER 106 SYMBOL LEVEL TYPE DESCRIPTION DDI_VTT Analog Input Bias Input. Selectable input for interfacing standard ECL outputs requiring 50 pull down to VTT power supply for a seamless interface. See Typical Application Circuit for recommended circuit application. 108, 109 DDI, DDI Input Digital Data Input Signals. Digital input signals from a GS1504 Equalizer or HD crosspoint switch. Because of on chip 50 termination resistors, a PCB trace characteristic impedance of 50 is recommended. 110 PD_VCC Power 111 A/D TTL Positive Supply. Phase detector most positive power supply connection. Input Control Signal Input. Used to select between the SDI/SDI input or DDI/DDI input. When A/D is HIGH; the SDI/SDI input is selected. When A/D is LOW; the DDI/DDI input is selected. 112 PDSUB_VEE Power Input Substrate Connection. Connect to phase detector's most negative power supply. 113 PD_VEE Power Input Negative Supply. Phase detector most negative power supply connection. 117 EQI_VCC Power Input Positive Supply. Most positive power supply connection for serial input stage. 120, 126 EQI_VEE Power Input Negative Supply. Most negative power supply connection for serial input stage. 122, 124 SDI, SDI Analog Input Serial Data Input Signals. AC coupled termination is recommended. Single ended to differential conversion is also feasible. The SDI and SDI input is selected when the A/D signal is high. Ensure that the trace length between the input connector and the GS1545 IC is kept to a minimum and that a PCB trace characteristic impedance of 75 is maintained between the connector and the device. 9 of 19 GENNUM CORPORATION 522 - 28 - 05 GS1545 Differential ECL/PECL INPUT/OUTPUT CIRCUITS PD_VCC 5k GS1545 PD_VCC 20k 20k PLCAP PLCAP PD_VEE DDI 10k 50 100A DDI 50 PD_VEE DDI_VTT Fig. 1 DDI/DDI Input Circuit Fig. 4 PLCAP/PLCAP Output Circuit PD_VCC 5k 5k LFA_VCC 500 LFA 10k 10k 40 40 31p VCO 5mA PD_VEE 50 100A VCO LFA_VEE Fig. 2 VCO/VCO Input Circuit Fig. 5 LFA Circuit PD_VCC 10k LFA_VCC 10k 25k DM DM LFS 85A 400A DFT_VEE LFA_VEE Fig. 3 DM/DM Output Circuit Fig. 6 LFS Output Circuit 10 of 19 GENNUM CORPORATION 522 - 28 - 05 LFA_VCC 10k PD_VCC 16k 5k LFS + - BYPASS 100A 100A GS1545 100A V = 2.4V 100A PD_VEE 100A LFA_VEE Fig. 7 LFS Input Circuit Fig. 11 BYPASS Circuit PD_VCC LFA_VCC 10k 20k PLL_LOCK LBCONT 5k PD_VEE LFA_VEE Fig. 8 PLL_LOCK Output Circuit Fig. 12 LBCONT Circuit PD_VCC 10k SP_VCC IJI 100 5k D[19:0] VCC 30k A 27k 0.1uF SP_VEE PD_VEE Fig. 9 IJI Output Circuit Fig. 13 D[19:0] Output Circuit PD_VCC 16k 20k PCLK_VCC + - A/D 2.4V 100 PCLK 100A 27k PD_VEE PCLK_VEE Fig. 10 A/D Input Circuit Fig. 14 PCLK Output Circuit 11 of 19 GENNUM CORPORATION 522 - 28 - 05 DDO_VCC 50 50 DDO_VCC DDO DDO GS1545 DDO_EN 20k 2k DDO_VEE DDO_VEE Fig. 15 DDO_EN Circuit Fig. 18 Serial (DDO) Output Stage Circuit EQO_VCC EQI_VCC 10k 6k 6k SDI 10k SDI RC 7k 7k CLI + EQI_VEE Fig. 16 Equalizer Input Circuit Fig. 19 CLI Output Circuit EQO_VCC EQI_VCC 40k 20k OUTPUT STAGE + MUTE CONTROL - MCLADJ 10k 42 CD EQO_VEE EQI_VEE Fig. 20 CD Circuit Fig. 17 MCLADJ Equivalent Circuit 12 of 19 GENNUM CORPORATION 522 - 28 - 05 DETAILED DESCRIPTION The GS1545 is a single standard equalizing receiver for serial digital HDTV signals at 1.485Gb/s and 1.485/1.001Gb/s. UNIQUE SLEW PHASE LOCK LOOP (S-PLL): DIGITAL INPUT BUFFER The input buffer is a self-biased circuit. On-chip 50 termination resistors provide a seamless interface for other HD-LINXTM products such as the GS1504 Adaptive Cable Equalizer. The digital input is selected by applying a logic low to the A/D pin. ANALOG INPUT The HD serial data signal may be connected to the input pins (SDI/SDI) in either a differential or single ended configuration. AC coupling of the inputs is recommended, as the SDI and SDI inputs are internally biased at approximately 2.7 volts. The input signal passes through a variable gain equalizing stage whose frequency response closely matches the inverse cable loss characteristic. In addition, the variation of the frequency response with control voltage imitates the variation of the inverse cable loss characteristic with cable length. The analog input is selected by applying a logic high to the A/D pin. PHASE (UI) 0.2 INPUT 0.1 OUTPUT 0.0 SLEW PLL RESPONSE PHASE (UI) 0.2 INPUT 0.1 OUTPUT 0.0 LINEAR (CONVENTIONAL) PLL RESPONSE Fig. 21 PLL Characteristics Slew PLLs offer several advantages such as excellent noise immunity. Because of the infinite bandwidth for an infinitely small input jitter modulation (or jitter introduced by VCO), the loop corrects for that immediately thus the small signal noise of the VCO is cancelled. The GS1545 uses a very clean, external VCO called the GO1515 (refer to the GO1515 Data Sheet for details). In addition, the bi-level digital phase detector provides constant loop bandwidth that is predominantly independent of the data transition density. The loop bandwidth of a conventional tri-stable charge pump drops with reducing data transitions. During pathological signals, the data transition density reduces from 0.5 to 0.05, but the slew PLLs performance essentially remains unchanged. The edge energy of the equalized signal is monitored by a detector circuit which produces an error signal corresponding to the difference between the desired edge energy and the actual edge energy. This error signal is integrated by an internal AGC filter capacitor providing a steady control voltage for the gain stage. As the frequency response of the gain stage is automatically varied by the application of negative feedback, the edge energy of the equalized signal is kept at a constant level which is representative of the original edge energy at the transmitter. The equalized signal is also DC restored, effectively restoring the logic threshold of the equalized signal to its correct level independent of shifts due to AC coupling. PHASE DETECTOR The phase detector portion of the slew PLL used in the GS1545 is a bi-level digital phase detector. It indicates whether the data transition occurred before or after with respect to the falling edge of the internal clock. When the phase detector is locked, the data transition edges are aligned to the falling edge of the clock. The input data is then sampled by the rising edge of the clock, as shown in Figure 22. In this manner, the allowed input jitter is 1UI p-p in an ideal situation. However, due to setup and hold time, the GS1545 typically achieves 0.5UI p-p input jitter tolerance without causing any errors in this block. When the 13 of 19 GENNUM CORPORATION 522 - 28 - 05 GS1545 A unique feature of the GS1545 is the innovative slew phase lock loop (S-PLL). When a step phase change is applied to the PLL, the output phase gains constant rate of change with respect to time. This behaviour is termed slew. Figure 21 shows an example of input and output phase variation over time for slew and linear (conventional) PLLs. Since the slewing is a nonlinear behavior, the small signal analysis cannot be done in the same way as the standard PLL. However, it is still possible to plot input jitter transfer characteristics at a constant input jitter modulation. Because most of the PLL circuitry is digital, it is more like other digital systems which are generally more robust than their analog counterparts. Additionally, signals like DM/DM which represent the internal functionality can be generated without adding additional artifacts. Thus, system debugging is also possible with these features. The complete slew PLL is made up of several blocks including the phase detector, the charge pump and an external Voltage Controlled Oscillator (VCO). signal is locked to the internal clock, the control output from the phase detector is refreshed at the transition of each rising edge of the data input. During this time, the phase of the clock drifts in one direction. PHASE ALIGNMENT EDGE RE-TIMING EDGE The GO1515 is an external hybrid VCO, which has a centre frequency of 1.485GHz and is also guaranteed to provide 1.485/1.001GHz within the control voltage (3.1V - 4.65V) of the GS1545 over process, power supply and temperature. The GO1515 is a very clean frequency source and, because of the internal high Q resonator, it is an order of magnitude more immune to external noise as compared to on-chip VCOs. The VCO gain, K, is nominally 16MHz/V. The control voltage around the average LFA voltage will be 500 x P/2. This will produce two frequencies off from the centre by =K x 500 x P/2. 0.5UI INPUT DATA WITH JITTER LBCONT OUTPUT DATA Fig. 22 Phase Detector Characteristics During pathological signals, the amount of jitter that the phase detector will add can be calculated. By choosing the proper loop bandwidth, the amount of phase detector induced jitter can also be limited. Typically, for a 1.41MHz loop bandwidth at 0.2UI input jitter modulation, the phase detector induced jitter is about 0.015UIp-p. This is not very significant, even for the pathological signals. The LBCONT pin is used to adjust the loop bandwidth by externally changing the internal charge pump current. For maximum loop bandwidth, connect LBCONT to the most positive power supply. For medium loop bandwidth, connect LBCONT through a pull-up resistor (RPULL-UP). For low loop bandwidth, leave LBCONT floating. The formula below shows the loop bandwidth for various configurations. ( 25k + R PULL - UP ) LBW = LBW NOMINAL x -----------------------------------------------------( 5k + R PULL - UP ) where LBW nominal is the loop bandwidth when LBCONT is left floating. CHARGE PUMP The charge pump in a slew PLL is different from the charge pump in a linear PLL. There are two main functions of the charge pump. One function is to hold the frequency information of the input data. This information is held by CCP1, which is connected between LFS and LFS. The other capacitor, CCP2 between LFS and LFA_GND is used to remove common mode noise. Both CCP1 and CCP2 should be the same value. The second function of the charge pump is to provide a binary control voltage to the VCO depending upon the phase detector output. The output pin, LFA controls the VCO. Internally there is a 500 pull-up resistor, which is driven with a 100A current called P. Another analog current F, with 5mA maximum drive proportional to the voltage across the CCP1, is applied at the same node. The voltage at the LFA node is VLFA_VCC - 500(P+F) at any time. Because of the integrator, F changes very slowly whereas P could change at the positive edge of the data transition as often as a clock period. In the locked position, the average voltage at the LFA (VLFA_VCC - 500(P/2+F) is such that VCO generates frequency , equal to the data rate clock frequency. Since P is changing all the time between 0A and 100A, there will be two levels generated at the LFA output. LOOP BANDWIDTH OPTIMIZATION Since the feed back loop has only digital circuits, the small signal analysis does not apply to the system. The effective loop bandwidth scales with the amount of input jitter modulation index. PHASE LOCK The phase lock circuit is used to determine the phase locked condition. It is done by generating a quadrature clock by delaying the in-phase clock (the clock whose falling edge is aligned to the data transition) by 166ps (0.25UI at 1.5GHz) with the tolerance of 0.05UI. When the PLL is locked, the falling edge of the in-phase clock is aligned with the data edges as shown in Figure 23. The quadrature clock is in a logic high state in the vicinity of input data transitions. The quadrature clock is sampled and latched by positive edges of the data transitions. The generated signal is low pass filtered with an RC network. The R is an on-chip 20k resistor and CPL is an external capacitor (recommended value 10nF). The time constant is about 67s, or more than a video line. 14 of 19 GENNUM CORPORATION 522 - 28 - 05 GS1545 IN-PHASE CLOCK VCO PHASE ALIGNMENT EDGE RE-TIMING EDGE IJI VOLTAGE 0.00 4.75 0.15 4.75 0.30 4.75 0.39 4.70 0.45 4.60 0.48 4.50 0.52 4.40 0.55 4.30 0.58 4.20 0.60 4.10 0.63 3.95 IN-PHASE CLOCK 0.5UI INPUT DATA WITH JITTER 0.25UI QUADERATURE CLOCK GS1545 P-P SINE WAVE JITTER IN UI PLCAP SIGNAL PLCAP SIGNAL 5.0 If the signal is not locked, the data transition phase could be anywhere with respect to the internal clock or the quadrature clock. In this case, the normalized filtered sample of the quadrature clock will be 0.5. When VCO is locked to the incoming data, data will only sample the quadrature clock when it is logic high. The normalized filtered sample quadrature clock will be 1.0. We chose a threshold of 0.66 to generate the phase lock signal. Because the threshold is lower than 1, it allows jitter to be greater than 0.5UI before the phase lock circuit reads it as "not phase locked". 4.8 IJI SIGNAL (V) Fig. 23 PLL Circuit Principles 4.6 4.4 4.2 4.0 3.8 3.6 0.00 0.20 0.40 0.60 0.80 INPUT JITTER (UI) INPUT JITTER INDICATOR (IJI) Fig. 24 Input Jitter Indicator (Typical at TA = 25C) This signal indicates the amount of excessive jitter (beyond the quadrature clock window 0.5UI), which occurs beyond the quadrature clock window (see Figure 23). All the input data transitions occurring outside the quadrature clock window, will be captured and filtered by the low pass filter as mentioned in the Phase Lock section. The running time average of the ratio of the transitions inside the quadrature clock and outside the quadrature is available at the PLCAP/PLCAP pins. A signal, IJI, which is the buffered signal available at the PLCAP is provided so that loading does not effect the filter circuit. The signal at IJI is referenced with the power supply such that the factor VIJI /V CC is a constant over process and power supply for a given input jitter modulation. The IJI signal has 10k output impedance. Figure 24 shows the relationship of the IJI signal with respect to the sine wave modulated input jitter. JITTER DEMODULATION (DM) The differential jitter demodulation (DM) signal is available at the DM and DM pins. This signal is the phase correction signal of the PLL loop, which is amplified and buffered. If the input jitter is modulated, the PLL tracks the jitter if it is within loop bandwidth. To track the input jitter, the VCO has to be adjusted by the phase detector via the charge pump. Thus, the signal which controls the VCO contains the information of the input jitter modulation. The jitter demodulation signal is only valid if the input jitter is less than 0.5UIp-p. The DM/DM signals have 10k output impedance, which could be low pass filtered with appropriate capacitors to eliminate high frequency noise. DFT_VEE should be connected to GND to activate DM/DM signals. The DM signals can be used as diagnostic tools. Assume there is an HDTV SDI source, which contains excessive noise during the horizontal blanking because of the transient current flowing in the power supply. In order to discover the source of the noise, one could probe around 15 of 19 GENNUM CORPORATION 522 - 28 - 05 the source board with a low frequency oscilloscope (Bandwidth < 20MHz) that is triggered with an appropriately filtered DM/DM signal. The true cause of the modulation will be synchronous and will appear as a stationary signal with respect to the DM/DM signal. The serial output signals DDO, DDO have a nominal voltage of 400mVpp differential, or 200mVpp single ended when terminated with 50. DDO_EN The DDO_EN enables or disables the serial output driver. To disable the driver, tie DDO_EN to VCC. To enable the driver, tie DDO_EN to VEE. When disabled, the supply current is reduced by approximately 10mA. A/D A/D is a TTL compatible input pin used to select between the analog or digital input. When A/D is at logic high, the analog input is selected. When A/D is low, the digital input is enabled. CLI The voltage output of CLI pin is proportional to the amount of cable present at the GS1545 analog input. With 0m of cable (800mV input signal levels), the CLI output voltage is approximately 3.3V. As the cable length increases, the CLI voltage decreases providing correlation between the CLI voltage and cable length. CLI voltage will be a function of the launch voltage and cable type/quality. MCLADJ Fig. 25 Jitter Demodulation Signal LOCK LOGIC Logic is used to produce the PLL_LOCK signal which is based on the LFS signal and phase lock signal. When there is not any data input, the integrator will charge and eventually saturate at either end. By sensing the saturation of the integrator, it is determined that no data is present. If either data is not present or phase lock is low, the lock signal is made low. Logic signals are used to acquire the frequency by sweeping the integrator. Injecting a current into the summing node of the integrator achieves the sweep. The sweep is disabled once phase lock is asserted. The direction of the sweep is also changed once LFS saturates at either end. BYPASS The BYPASS block bypasses the reclocked/mute path of the data whenever a logic low input is applied to the BYPASS input. In the bypass mode, the mute does not have any effect on the parallel outputs. Also, the internal PLL still locks to a valid HDTV signal and shows PLL_LOCK. The outputs of the GS1545 can be muted when the input signal decreases below a preselected input level. The MCLADJ pin may be left unconnected for applications where output muting is not required. The use of a Carrier Detect function with a fixed internal reference does not solve this problem since the signal to noise ratio on the circuit board could be significantly less than the default signal detection level set by the on chip reference. CARRIER DETECT The CD pin is a TTL compatible output signal. When a carrier is detected at the analog input, the CD pin is pulled low. When a carrier is not detected, the CD will be pulled high. SERIAL TO PARALLEL CONVERTER The high-speed serial to parallel converter accepts differential clock and data signals from the reclocker core. The S/P core converts this serial output into a 20-bit wide data stream (D[19:0]). Note that this data stream is not word aligned or descrambled. It also provides a parallel clock, which is 1/20th the serial clock rate (PCLK_OUT). The outputs of the S/P block are TTL compatible. When the PLL loses lock, the parallel clock continues to freewheel. The parallel clock and data outputs were designed for seamless interfaces to the GS1500 and GS1510 deformatters. 16 of 19 GENNUM CORPORATION 522 - 28 - 05 GS1545 Figure 25 shows an example of such a situation. An HDTV SDI signal is modulated with a modulation signal causing about 0.2UI jitter in Figure 25 (Channel 1). The GS1545 receives this signal and locks to it. Figure 25 (Channel 2) shows the DM signal. Notice the wave shape of the DM signal, which is synchronous to the modulating signal. The DM/DM signal could also be used to compare the output jitter of the HDTV signal source. SERIAL OUTPUT STAGE J5 47 C33 10n R15 R12 75 1p5 R13 75 All resistors in ohms, all capacitors in farads, unless otherwise shown. J3 BNC_ANCHOR J1 L5 10nH SECOND PAIR OF BNC SHOWN IS FOR DUAL FOOTPRINT OPTION ON INPUT CONNECTORS J6 Note that these outputs are not cable drivers A/D 47 C32 BYPASS 118 nc C17 10n 119 nc 120 EQI_V EE 121 nc C18 122 SDI 123 nc 47p C20 124 SDI 125 nc 47p 126 37.5 EQI_VEE 127 nc 128 nc CC 10n C27 R8 15k 10n C19 R6 10k C55 10 C54 100n VCC PLCAP L10 R111 116 nc ANALOG POWER PLANE 117 EQI_V 106 DDI_V TT 107 nc 108 DDI 109 DDI 110 PD_V CC 111 A/D 112 PDSUB_VEE 113 PD_V EE 114 nc 115 nc 1 nc 2 nc C25 VCC nc 102 103 nc 104 nc 105 BYPASS 3 nc 4 nc VCC nc 101 nc 100 PLL_LOCK nc 99 98 PLL_LOCK nc 97 CLI 5 MCLAD 6 nc 7 VCC R17 2k VCO 0 91 10n C26 L17 100n 10 VCC C56 100n C59 10 C60 100n C61 10 C64 C53 R116 0 VCO 92 nc 8 nc 9 nc 10 nc 11 nc nc 88 nc 87 10n C22 VCC 14 nc 15 nc 16 EQO_V CC PLCAP 96 nc 95 nc 94 93 CLI 1 C28 + LFS + 47 C23 47 C24 + VCC V C35 CC 10n J4 J7 L8 100n 10 C50 C51 10 100n C49 C52 MAIN POWER PLANE DIGITAL POWER PLANE GS1545 1 C34 + VCC VCO POWER PLANE nc IJI 86 LFS 85 84 nc 17 DDO 18 DDO 19 DDO_V EE 0 25 nc 26 nc 27 nc 28 nc nc 90 VCO 89 12 CD 13 EQO_V EE CD DDO_EN SDO_EN 21 DDO_VCC 22 nc nc 23 LFA_VEE 75 LBCONT 74 VCC VCC nc 83 nc 82 81 20 DM 80 79 DM nc 78 nc 77 DFT_VEE 76 24 VCC nc 70 nc 69 0 R19 nc 68 nc 67 VCC nc 66 nc 65 37 nc 38 nc LFA LFA 73 LFA_VCC 72 nc 71 29 nc 30 SP_V CC 17 of 19 31 SP_V CC 32 SP_V EE VCC 33 SP_V EE 34 PCLK_OUT 35 PCLK_V CC 36 PCLK_V EE VCC 10n 10n 10n 60 61 42 43 41 D0 nc 40 nc 39 D1 D2 nc 51 D9 50 49 D8 48 D7 47 D6 46 D5 45 D4 D3 44 D10 53 nc 52 56 D13 D12 55 D11 54 59 D14 nc 58 nc 57 D15 D16 62 D19 64 D18 63 D17 10n C65 PCLK D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 (110/112) (19/21) (30-31/32-33) (35/36) C31 C30 C29 VCC GS1545 GENNUM CORPORATION TYPICAL APPLICATION CIRCUIT 522 - 28 - 05 TYPICAL APPLICATION CIRCUIT (continued) GO1515 VCO POWER CONNECT LFA VCC C43 C41 + 100n VCC 10 C42 + C44 100n VCTR 1 2 VCC 3 GND GND 8 GS1545 LOCK DETECT 7 nc 6 GND U2 GND GO1515 5 O/P 4 GS1545 10 VCC R27 R26 PLL_LOCK VCO GS1545 CONFIGURATION JUMPERS VCC BYPASS VCC Q3 150 GS1545 CD VCC A/D LED3 22k VCC R25 DDO_EN Q1 CD 20k R28 LED4 150 All resistors in ohms, all capacitors in farads, unless otherwise shown. APPLICATION INFORMATION Please refer to the EBHDRX evaluation board documentation for more detailed application and circuit information on using the GS1545 with the GS1500 and GS1510 Deformatters. 18 of 19 GENNUM CORPORATION 522 - 28 - 05 PACKAGE DIMENSIONS 23.20 0.25 20.0 0.10 18.50 REF GS1545 12 TYP 12.50 REF 0.75 MIN 17.20 0.25 0 -7 14.0 0.10 0.30 MAX RADIUS 0-7 0.13 MIN. RADIUS 0.88 0.15 1.6 REF 3.00 MAX 0.50 BSC 0.27 0.08 128 pin MQFP All dimensions are in millimetres. 2.80 0.25 CAUTION ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION REVISION NOTES: DOCUMENT IDENTIFICATION Added lead-free and green information. PRELIMINARY DATA SHEET The product is in a preproduction phase and specifications are subject to change without notice. GENNUM CORPORATION MAILING ADDRESS: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 SHIPPING ADDRESS: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5 For latest product information, visit www.gennum.com GENNUM JAPAN CORPORATION Shinjuku Green Tower Building 27F 6-14-1, Nishi Shinjuku Shinjuku-ku, Tokyo 160-0023 Japan Tel: +81 (03) 3349-5501 Fax: +81 (03) 3349-5505 GENNUM UK LIMITED 25 Long Garden Walk, Farnham, Surrey, England GU9 7HX Tel. +44 (0)1252 747 000 Fax +44 (0)1252 726 523 Gennum Corporation assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement. (c) Copyright May 2000 Gennum Corporation. All rights reserved. Printed in Canada. 19 of 19 522 - 28 - 05