12-142
PRELIMINARY
High Sensitivity, High Speed
Photocoupler
6N139 Series
6N139
6N139M
6N139S
6N139S-TA
6N139S-TA1
6N139-V
6N139M-V
6N139S-V
6N139STA-V
6N139STA1-V
Part Number Package Application part
number
8-pin DIP
8-pin (leads with 0.4" spacing)
8-pin (lead bends for surface mount)
8-pin (tape and reel packaging of type I)
8-pin (tape and reel packaging of type II)
8-pin DIP
8-pin (leads with 0.4" spacing)
8-pin (lead bends for surface mount)
8-pin (tape and reel packaging of type I)
8-pin (tape and reel packaging of type II)
6N139
6N139
Features
High current transfer ratio
( CTR : MIN. 500% at IF = 1.6mA )
High speed response
( tPHL : TYP. 0.2 s at RL = 270 )
Instantaneous common mode rejection voltage
( CMH : TYP. 500V/ s )
TTL compatible output
Options Available :
- Leads with 0.4" (10.16mm) Spacing (M Type)
- Lead Bends for Surface Mounting (S Type)
- Tape and Reel of Type I for SMD (Add "-TA" Suffix)
- Tape and Reel of Type II for SMD (Add "-TA1" Suffix)
- VDE 0884 Approvals (Add "-V" Suffix)
Applications
1. Interfaces for computer peripherals
2. Electronic calculators, measuring instruments, control
equipment
3. Telephone sets
4. Signal transmission between circuits of different poten-
tials and impedances
Package Dimensions
NOTES :
1. Year date code.
2. 2-digit work week.
3. Factory code shall be marked (Z Taiwan, Y Thailand).
4. All dimensions are in millimeters (inches).
5. Tolerance is 0.25mm (.010") unless otherwise noted.
6. Specifications are subject to change without notice.
Ordering Information
PRELIMINARY
PHOTOCOUPLER
12-143
Ratings and Characteristics
Absolute Maximum Ratings (Ta=25 )
Input
Output
*1. AC for 1 minute, R.H. = 40 ~ 60%
Isolation voltage shall be measured using the following method.
(1) Short between anode and cathode on the primary side and between collector and emitter on the secondary side.
(2) The isolation voltage tester with zero-cross circuit shall be used.
(3) The waveform of applied voltage shall be a sine wave.
*2. For 10 seconds
Electrical / Optical Characteristics ( Ta = 0 ~ +70 unless otherwise specified )
*1.Isolation Voltage
Operating Temperature
Storage Temperature
*2.Soldering Temperature
Parameter
mA
V
mW
V
V
V
mA
mW
Vrms
20
5
35
-0.5~+18
-0.5~+18
0.5
60
100
2,500
0~+70
-55~+125
260
IF
VR
P
VCC
VO
VEBO
IO
PO
Viso
Topr
Tstg
Tsol
Symbol Rating Unit
Forward Current
Reverse Voltage
Power Dissipation
Supply Voltage
Output Voltage
Emitter-base Reverse Withstand Voltage (pin 5 to 7)
Average Output Current
Power Dissipation
*1. Current transfer ratio is the ratio of input current and output current expressed in %.
*2. Measured as 2-pin element ( Short 1, 2, 3, 4 and 5, 6, 7, 8 )
Input Forward Voltage
Input Forward Voltage Temperature Coefficient
Input Reverse Voltage
Input Capacitance
*1 Current Transfer Ratio
Logic (0) Output Voltage
Logic (1) Output Current
Logic (0) Supply Current
Logic (1) Supply Current
*2 Leak Current (Input-Output)
*2 Isolation Resistance (Input-Output)
Capacitance (Input-Output)
Parameter Symbol Min. Typ. Max. unit Conditions
Ta=25 , IF=1.6mA
IF=1.6mA
Ta=25 , IR=10 A
VF=0, f=1MHz
IF=0.5mA, VO=0.4V
VCC=4.5V
IF=1.6mA, VO=0.4V
VCC=4.5V
IF=1.6mA VCC=4.5V
IO=6.4mA
IF=5mA VCC=4.5V
IO=15mA
IF=12mA VCC=4.5V
IO=24mA
IF=0, VCC=VO=18V
IF=1.6mA, VCC=5V
VO=open
IF=0, VCC=5V
VO=open
Ta=25 , 45%RH,
t=5s, VI-O=3kV DC
VI-O=500VDC
f=1MHz
V
mV/
V
pF
%
%
V
V
V
A
mA
A
A
pF
1.7
0.4
0.4
0.4
100
1.5
10
1.0
-1.9
60
1800
1600
0.1
0.1
0.1
0.05
0.5
0.01
1012
0.6
5.0
400
500
VF
VF/ Ta
BVR
CIN
CTR
VOL
IOH
ICCL
ICCH
II-O
RI-O
CI-O
12-144
PRELIMINARY
Electrical / Optical Characteristics ( Ta = 25 VCC = 5V)
*3 Instantaneous common mode rejection voltage "output (1)" represents a common mode voltage variation
that can hold the output above (1) level (Vo>2.0V).
Instantaneous common mode rejection voltage "output (0)" represents a common mode voltage variation
that can hold the output above (0) level (Vo<0.8V).
Propagation Delay time Output (1) (0)
Propagation Delay time Output (0) (1)
*3 Instantaneous common mode rejection voltage
output(1)
*3 Instantaneous common mode rejection voltage
output(0)
Parameter Symbol Min. Typ. Max. Unit Conditions
IF=0.5mA,
RL=4.7k
IF=12mA,
RL=270
IF=0.5mA,
RL=4.7k
IF=12mA,
RL=270
IF=0, VCM=10VP-P1
RL=2.2k
VCM=10VP-P, IF=1.6mA
RL=2.2k
s
s
s
s
V/ s
V/ s
25
1
60
7
5
0.5
10
1.5
500
-500
tPHL
tPLH
CMH
CML
PRELIMINARY
PHOTOCOUPLER
12-145
Typical Electrical/Optical Characteristic Curves
(25 Ambient Temperature Unless Otherwise Noted)
12-146
PRELIMINARY
