DG441AK/883B - Maxim Integrated

SCOPE: IMPROVED, QUAD, SPST, CMOS ANALOG MULTIPLEXER

Device Type Generic Number

01 DG441A(x)/883B

02 DG442A(x)/883B

Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows:

Outline Letter Mil-Std-1835 Case Outline Package Code

K GDIP1-T16 or CDIP2-T16 16 LEAD CERDIP J16

Z CQCC1-N20 20-Pin Ceramic LCC L20

A bsol ute Maximum Ratings

Voltage Referenced to V-

V+ to V- .............................................................................................................................. 44V

V- to GND .......................................................................................................................... 25V

VL ................................................................................................... (GND-0.3V) to V+ +0.3V)

Digital Inputs, VS, VD 1/ ..........................................................................(V -) -2V to (V+ )+2V

or 30mA whichever occurs first

Continuous Current, Any terminal .................................................................................. 30mA

Peak Current, S or D (Pulsed at 1ms, 10% duty cycle max) ......................................... 100mA

Lead Temperature (soldering, 10 seconds) ........................................................................ +300°C

Storage Temperature ........................................................................................... -65°C to +150°C

Continuous Power Dissipation ........................................................................…….... TA=+70°C

16 lead CERDIP(derate 10.0mW/°C above +70°C) ...............................................…….. 800mW

20 lead LCC (derate 9.1mW/°C above +70°C) ......................................................…….. 727mW

Junct ion Temperature TJ ....................................................................................………. +150°C

Thermal Resista nce, J unction to Case, ΘJC:

Case Outline 16 lead CERDIP...............................................................…….... 50°C/W

Case Outline 20 lead LCC .....................................................................……... 20°C/W

Thermal Resistance, Junction to Ambient, ΘJA:

Case Outline 16 lead CERDIP.............................................................…….... 100°C/W

Case Outline 20 lead LCC ...................................................................……... 110°C/W

Recommended Operating Co ndit ions

Ambient Operating Range (TA) .........................................................……….. -55°C to +125°C

Positive Supply Voltage (V+) ...............................................................................………... +15V

Negative Supply Voltage (V-) ..............................................................................……….... -15V

VAL (max) .............................................................................................................…….…... 0.8V

VAH (min) .............................................................................................................……….... 2.4V

NOTE 1: Signals on S, D, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward current

to maximum current ratings.

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.

These are stress ratings only, and functional operation of the device at these or any other conditions beyond

those indicated in the operational section s of the sp ecifica tions is not implied. Exposure to absolute maximum

rating conditions for extended periods may affect device reliability.

---------------------------- Electrical Characteristics of DG441A/DG442A/883B 19-0093 Rev. C

Page 2 of 6

TABLE 1. ELECTRICAL TESTS: DUAL SUPPLY

TEST Symbol

CONDITIONS

-55 °C <=TA<= +125°C

V+=+15V, V-=-15V, GND=0V

VAH=2.4V, VAL=0.8V

Unless otherwise specified

Group A

Subgroup Device

type Limits

Min

Limits

Max

Units

SWITCH

Analog-Signal

Range VANALOG NOT E 3 1,2,3 All -15 15 V

Drain-Source ON

Resistance rDS(ON) IS =-10mA, VD=±8.5V,

V+=13.5V, V-=-13.5V 1

2,3 All 85

100 Ω

On-Resistance

Match Between

Channels 4/

∆rDS

(ON)

IS =-10mA, VD=±10V,

V+=15V, V-=-15V 1

2,3 All 4

5Ω

On-Resistance

Flatness 4/ rFLAT

(ON)

IS =-10mA, VD=5V or -5V,

V+=15V, V-=-15V 1

2,3 All 9

15 Ω

Source- OFF

Leakage Current IS(OFF) V+=16.5V, V-=-16.5V, VIN=2.4V

VS=±15.5V VD =±15.5V 1

2,3 All -0.5

-20 0.5

20 nA

Drain- OFF

Leakage Current ID(OFF) V+=16.5V, V-=-16.5V,

VS=±15.5V VD =±15.5V 1

2,3 All -0.5

-20 0.5

20 nA

Channel-On

Leakage Current ID(ON)

IS(ON)

V+=16.5V, V-=-16.5V,

VS=±15.5V VD =±15.5V 1

2,3 01 -0.5

-20 0.5

20 nA

INPUT

Input

Current/Voltage

High IINH

VIN=2.4V 1,2,3 All -500 500 nA

Input

Current/Voltage

Low

IINL VIN= 0.8V 1,2,3 All -500 500 nA

SUPPLY

Power Supply

Range 1,2,3 All ±4.5 ±20 V

Positive Supply

Current I+ All channels on or off,

V+=16.5V, V-=-16.5V,

VIN=0 or 5V

1,2,3 All 100 µA

Negat ive Supply

Current I- All channels on or off,

V+=16.5V, V-=-16.5V,

VIN=0 or 5V

2,3 All -1

-5 1

5µA

Ground Current IGN D All c hannels on or off,

V+=16.5V, V-=-16.5V,

VIN=0 or 5V

1,2,3 All -100 µA

DYNAMIC

Turn-On Time tON VS=±10V, RL=1kΩ, Figure 2 9All 250 ns

Turn-O ff Time tOFF VD=±10V, RL=1kΩ, Figure 2 901

02 120

170 ns

Charge Injection

NOTE 2 QCL=1nF, VGEN=0V, RGEN=0Ω,

Figure 3 9All 10 pC

---------------------------- Electrical Characteristics of DG441A/DG442A/883B 19-0093 Rev. C

Page 3 of 6

TABLE 1. ELECTRICAL TESTS: SINGLE SUPPLY

TEST Symbol

CONDITIONS

-55 °C <=TA<= +125°C

V+=+12V, V-=0V, GND=0V

VAH=2.4V, VAL=0.8V

Unless otherwise specified

Group A

Subgroup Device

type Limits

Min

Limits

Max

Units

SWITCH

Analog-Signal

Range VANALOG NOTE 3 1,2,3 All 012V

Drain-Source ON

Resistance rDS(ON) IS =1.0mA, VD=3V or 8V,

V+=10.8V 1,3

2All 160

200 Ω

SUPPLY

Power Supply

Range 1,2,3 All 10 30 V

Positive Supply

Current I+ All channels on or off,

VIN=0 or 5V 1,2,3 All 100 µA

Negat ive Supply

Current I- All channels on or off,

VIN=0 or 5V 1

2,3 All -1

-5 1

5µA

Ground Current IGN D All c hannels on or off, VIN=0 or 5V 1,2,3 All -100 µA

DYNAMIC

Turn-On Time tON VS=8V, Figure 2 9 All 400 ns

Turn-O ff Time tOFF VS=8V, Figure 2 9 All 200 ns

Charge Injection QCL=1nF, VGEN=0V NOTE 3 9 All 10 pC

NOTE 2: The algebraic convention, where the most negative value is a minimum and the most positive value a

maximum, is used in this data sheet.

NOTE 3: Guaranteed by design.

NOTE 4: On-resistance match between channels and flatness is guaranteed only with bipolar-supply operation.

Flatness is defined as the difference between the maximum and the minimum value of on-resistance

as measured at the extremes of the specified analog range.

TRUTH TABLE TERMINAL CONNECTION

LOGIC DG441A

SWITCH TERMINAL

NUMBER 01

DG441A 01

DG441A 02

DG442A 02

DG442A

0 ON J16 20LCC J16 20LCC

1 OFF 1 IN1 NC IN1 NC

2 D1 IN1 D1 IN1

3S1D1S1D1

LOGIC DG442A 4V-S1V-S1

SWITCH 5 GND V- GND V-

0OFF 6S4NCS4NC

1 ON 7 D4 GND D4 GND

8IN4S4IN4S4

9 IN3 D4 IN3 D4

10 D3 IN4 D3 IN4

11 S3 NC S3 NC

12 NC IN3 NC IN3

13 V+ D3 V+ D3

14 S2 S3 S2 S3

15 D2 NC D2 NC

16 IN2 NC IN2 NC

17 V+ V+

18 S2 S2

19 D2 D2

20 IN2 IN2

---------------------------- Electrical Characteristics of DG441A/DG442A/883B 19-0093 Rev. C

Page 4 of 6

Figure 2. Switching Time: See Commercial Data Sheet.

Figure 3. Charge Injection: See Commercial Data Sheet.

ORDERING INFORMATION:

DG441AK/883B 16 CDIP DG442AK/883B 16 CDIP

DG441AZ/883B 20 LCC DG442AZ/883B 20 LCC

QUALITY ASSURAN CE

Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil-

Std-883.

Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:

1. Test Condition, A, B, C, or D.

2. TA = +125°C minimum.

3. Interim and final electrical test requirements shall be specified in Table 2.

Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B,

C, and D inspection.

Group A inspection:

1. Tests as specified in Table 2.

2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.

Group C and D inspections:

a. End-point electrical parameters shall be specified in Table 1.

b. Steady-state life test, Method 1005 of Mil-Std-883:

1. Test condition A, B, C, D.

2. TA = +125°C, minimum.

3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.

TABLE 2. ELECTRICAL TEST R EQUIREMENTS

Mil-Std-883 Test Requirements Subgroups

per Method 5005, Table 1

Interim Electric Parameters

Method 5004 1

Final Electrical Parameters

Method 5005 1*, 2, 3, 9

Group A Test Requirements

Method 5005 1, 2, 3, 9

Group C and D End-Point Electrical Parameters

Method 5005 1

* PDA applies to Subgroup 1 only.

---------------------------- Electrical Characteristics of DG441A/DG442A/883B 19-0093 Rev. C

Page 5 of 6