IEC & British Standard Fuses IEC and British Standard Fuses Section Contents Application Data Page Application Data . . . . . . . . . . . . . . . . . . . . . 217-218 HRC fuse holders CAMaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .235 SAFEloc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .235 RED indicates NEW information Supplementary ranges cover applications up to 660Vac and 500Vdc including those with nonstandard tag fixings. Cooper Bussmann fuses are manufactured under quality systems independently assessed to BS 5750 (ISO 9002) and appropriate ratings carry the ASTA 20 endorsement. Selecting fuses is relatively simple and effective. The following notes cover the majority of applications. For further information contact our Application Engineers at 636-527-1270. Circuit Loading The current rating of the fuse should not be less than the full load current of the circuit. The circuit should be so designed that small overloads of long duration will not be of frequent occurrence. Cable Ratings & Protection There is an increasing move away from 70C PVC insulation to materials that are more environmentally friendly, for example 90C XLPE. The ratings of fusegear, switches, accessories, etc. are generally based upon the equipment being connected to conductors intended to be operated at a temperature not exceeding 70C in normal service. In view of the above, it is recommended that the practice of designs based upon conductor temperatures of 70C be regarded as the norm. The equipment manufacturer should be consulted to ascertain the reduction of nominal current rating of the equipment if conductor temperatures exceeding 70C are used. In addition, an overriding factor is often voltage drop. Fuses with gG characteristics protect associated cables against both overload and short-circuit current, provided that the current rating of the fuse 1N is equal or less than the current carrying capacity of the cable 1z. In motor circuits, the motor starter will provide the overload protection and the fuses will provide the short-circuit protection. The maximum fuse size that can be used depends upon the type of cable used and is determined using the appropriate K factor. The following table gives the maximum sizes of fuses that are recommended for two popular cables with copper conductors, 70C PVC (K = 115) and 90C thermosetting (K = 143). For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 217 IEC & British Fuses CSA Type P and Type D fuses (CDS, CDN & PON) . . . . . . . . . . . . . . . . . . . . . . . . . . . .219 Tron(R) HRC Form II Class C fuses (CGL Form II Class C) . . . . . . . . . . . . . . . . . . . . . . . . . . 220 HRCI Industrial ceramic body fuses (CIF21 HRCI-CA & CIF06 HRCI-CB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 HRCI-J Fast-acting fuses (CJ HRCI-J) . . . . . . . . . . . . . . . 222 HRCI-Miscellaneous Type K fuses (CIH, CIK & CIL HRCI-MISC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 HRC Form II current-limiting fuses . . . . . . . . . . . . . . . . . .224 BS 88 British Standard low voltage fuses (SSD, NSD, ESD & STD, NITD, AAO, BAO, OSD, CEO, DEO BS 88 Part 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 BS 88 British Standard low voltage fuses (AC, AD, BC, BD, CD, DD, ED, EFS & EF, FF, FG, GF, GG, GH BS 88) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .226 DIN Style Type D (D16, D27, D33, D125 Type D) . . . . . . 227 Neozed low voltage fuses (NZ01, NZ02 Type D0) . . . . . . 227 NH HRC Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228-231 Class gG/gL IEC Industrial ferrule fuses (C08G, C08M, C10G, C10M, C14G, C14M, C22G, C22M) . . . . . . . . . . 232 Class aM IEC Industrial ferrule fuses (C08M, C10M, C14M, C22M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .233 Class aM & gG/gL IEC Industrial ferrule fuses with striker (C14G_S, C22G_S, C14M_S, C22M_S) . . . . . . . . . . . . . 234 The standard range of fuses for low voltage industrial and general purpose applications meet the requirements of BS 88 and IEC 60269. By using advanced fuse technology, current ratings up to 400A have compact dimensions, but retain standard dimensional and performance requirements. These designs are for 315/240V systems. The standard range of fuses are available from 2-1250A in the following tag forms: Offset Blade - Offset Bolted - Center Bolted. IEC & British Standard Fuses Application Data for BS Low Voltage Fuses Cable Size (mm2) 1 1,5 2.5 4 6 10 16 25 35 50 70 95 120 Max. Fuse Rating (amps) K = 115 K = 143 16 16 20 25* 32* 32* 50* 50* 63* 63* 100* 125* 125* 160* 200* 250* 315* 355* 400* 500 560 630 710 800 800 1000 * Extended Motor Circuit dual ratings can be used. Protection Against Electrical Shock For a TN System, a disconnecting time not exceeding 5s is permitted for a distribution circuit. The maximum values of earth fault loop impedance (Zs) of 240V for Cooper Bussmann gG fuses to BS 88: Parts 2 and 6 are: Rating (A) Zs (Ohms) Rating (A) Zs (Ohms) Rating (A) Zs (Ohms) 6 14 50 1.1 250 0.16 10 7.7 63 0.86 315 0.13 16 4.3 80 0.60 400 0.096 20 3.0 100 0.44 500 0.073 25 2.4 125 0.35 630 0.054 32 1.9 160 0.27 800 0.044 40 1.4 200 0.20 Ambient Temperature The derating, in terms of current, of 0.5% per C above an ambient of 35C is recommended. Capacitor Circuits For power factor correction in capacitor circuits, the fuse should be chosen with a current rating greater than 1.5 times the rated capacitor current. This takes into account the high inrush current, circuit harmonics and capacitor tolerances. Motor Circuits In motor circuits, the fuse has to withstand the motor's starting current and often requires a higher rating than the motor's full load current. Coordination recommendations are made by the manufacturers of motor starters in accordance with IEC 60947-4-1. To get Type 2 coordination with fuses, tests are performed with the latest gG or gM fuses to BS 88 or IEC 60269 that have pre-arcing I2t values towards the bottom of specified limits. This means that Cooper Bussmann fuses are suitable to provide Type 2 coordination. Extended dual ratings of motor circuit protection fuses with gM characteristics are available in most popular fuse sizes to extend the use of associated equipment with appropriate economies. In the majority of applications, gG fuses are used. It is not essential to use gM fuses for motor circuit protection, they simply extend the utilization of standard equipment. Below is a table of recommended fuses at 415V. In most applications, the run-up time is less than 5 seconds and duty is infrequent - no more than twice per hour. The next larger rating should be used for more demanding applications. Interrupting Rating The standardized interrupting rating values are 80kA for voltages of 415Vac and above, and 40kA for DC applications. The 240Vac designs have an interrupting rating of 50kA. Coordination Ratio All fuses to BS 88 Parts 2 and 6 will give a coordination ratio of 2:1; and for most practical situations a ratio of 1.6:1 (two steps in the R10 series). Example: an upstream fuse rated at 160A will coordinate with a downstream fuse rated at 100A. Current and Energy Limitation The range of fuses have pre-arcing I2t values towards the bottom limits of BS 88 Parts 2 and 6. This ensures excellent current and energy limitation. They also have lower power losses at rated current. This assists in the appropriate interchangeability with other makes of fuses. Transformers When fuses are used on the primary side of transformers, the normal fuse current rating should be at least twice the nominal transformer primary current. Fluorescent Lighting The normal fuse current rating should be at least twice the normal full load current of the maximum number of lights to be simultaneously switched. 218 kW 0.25 0.37 0.55 0.75 1.1 1.5 2.2 3.0 4.0 5.5 7.5 11.0 15.0 18.5 22.0 30.0 37.0 45.0 55.0 75.0 90.0 110.0 132.0 150.0 185.0 200.0 225.0 250.0 280.0 335.0 355.0 Rating Motor A 0.8 1.1 1.5 2.0 30 3.6 5.0 6.5 8.4 11.0 15.0 20.0 27.0 33.0 38.0 54.0 66.0 79.0 98.0 135.0 155.0 185.0 220.0 250.0 310.0 335.0 375.0 415.0 460.0 562.0 596.0 Direct On-line Standard Motor Circuit (gG) (gM) A A 4 4 6 6 10 16 16 20 20 25 20M25 40 32M40 50 32M50 63 32M63 80 63M80 80 63M80 100 63M100 125 100M125 160 100M160 160 100M160 250 200M250 250 200M250 315 200M315 355 315M400 355 315M400 450 400M500 500 4 00M500 560 560 630 710 800 - For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa Asst. Start Standard (gG) A 2 2 4 4 6 01 01 61 61 2 20 25 32 40 50 50 80 80 100 100 160 160 200 250 315 355 400 400 450 500 630 710 IEC & British Standard Fuses CSA Type P and Type D Fuses CDS, CDN & PON Type P & D Specifications Description: CSA time-delay Type D & P fuses. Dimensions: See Catalog Numbers table and Dimensions illustration. Ratings: Volts: -- 250Vac (CDN & PON) -- 600Vac (CDS) Amps: -- 10-600A IR: -- 10kA minimum Agency Information: CE, CSA Certified to C22.2 No. 59.1. Features and Benefits * Economical fuse in a variety of ratings for applications not requiring time-delay. Dimensions A IEC & British Fuses Typical Applications * Lighting, heating and other circuits not subject to temporary surges and where available short-circuit current are relatively low. B Basic Catalog Numbers Ferrule Design--1 through 60A Time-Delay CSA Type "D" Fuses Catalog Numbers CDN CDS Amp Ratings Below 10A use FRN-R 10, 12, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100 110, 125, 150, 175, 200, 225, 250, 300, 350, 400, 450, 500, 600 Below 10A use FRS-R 10, 12, 15, 20, 25, 30, 35, 40, 45, 50, 60 70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250, 300, 350, 400, 450, 500, 600 Volts 250Vac 600Vac C A D B F E Knife Blade--70 through 600A One-Time CSA Type "P" Fuses Catalog Number PON Amp Ratings 15, 20, 25, 30, 35, 40, 45, 50, 60 Volts 250Vac Catalog Numbers Basic Catalog Number and Volts CDN/PON 250Vac CDS 600Vac Amp Ratings 1-30 35-60 70-100 110-200 225-400 450-600 1-30 35-60 70-100 110-200 225-400 450-600 A Overall 2.0 (50.8) 3.0 (76.2) 5.88 (149.4) 7.3 (185.4) 8.63 (219.2) 10.38 (263.7) 5.0 (127.0) 5.5 (139.7) 7.88 (200.2) 9.63 (244.6) 11.63 (295.4) 13.38 (339.9) B Max Diameter 0.56 (14.3) 0.81 (20.6) -- -- -- -- 0.81 (20.6) 1.06 (27.0) -- -- -- -- Dimensions in (mm) C Min D Min Blade Length Barrel Length -- -- -- -- 1.0 (25.4) -- 1.38 (34.9) 4.13 (104.8) 1.88 (47.6) 4.63 (117.5) 2.25 (57.2) 5.19 (131.8) -- -- -- -- 1.0 (25.4) -- 1.38 (34.9) 6.13 (115.6) 1.88 (47.6) 7.13 (118.1) 2.25 (57.2) 8.19 (208.0) E Blade Thickness -- -- 0.13 (3.2) 0.19 (4.8) 0.25 (6.4) 0.25 (6.4) -- -- 0.13 (3.2) 0.19 (4.8) 0.25 (6.4) 0.25 (6.4) F Blade Width -- -- 0.75 (19.1) 1.13 (28.6) 1.63 (41.3) 2 (50.8) -- -- 0.75 (19.1) 1.13 (28.6) 1.63 (41.3) 2 (50.8) To Order To order, specify Basic Catalog Number and amp rating. Example: CDN-30 Data Sheet: 4126 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 219 IEC & British Standard Fuses Tron(R) HRC Form II Class C Fuses CGL Form II Class C Specifications Description: Current-limiting HRCII-C fuses designed to withstand inrush currents on typical motor start-ups while offering high current limitation in the short-circuit region. Dimensions: See Dimensions illustrations. Ratings: Volts: -- 600Vac/250Vdc (1-30A) Amps: -- 1-600A IR: -- 200kA (40,000A DC) Agency Information: CE, CSA Certified, C22.2 No. 106. Dimensions 0.22" 0.81" 0.22" (20.64mm) (5.56mm) (5.56mm) 0.06" 2.0" (1.59mm) 0.34" (50.8mm) 2.80" 0.94" (8.73mm) (23.81mm) (71.04mm) 3.31" (84.14mm) CGL 1-30 0.22" 0.81" 0.22" (20.64mm) (5.56mm) (5.56mm) 0.06" 2.0" (50.8mm) (1.59mm) 0.50" 2.80" 1.06" (12.7mm) (71.04mm) (26.92mm) 3.5" (88.9mm) Features and Benefits * Close sizing to loads allows using smaller and less costly switches * Provides a higher degree of short-circuit protection * Helps protect motors against burnout from overloads CGL 35-60 0.343" 0.343" (8.71mm) (8.71mm) 2.39" Typical Applications * For use in circuits subject to surge currents such as those caused by motors, transformers and other inductive loads (60.72mm) 3.64" 1.34" (34.04mm) 0.09" (2.29mm) 0.75" 1.375" (19.05mm) (34.93mm) (92.47mm) 4.31" (109.54mm) CGL 70-100 Catalog Numbers (-Amps) CGL-1 CGL-2 CGL-3 CGL-4 CGL-6 CGL-10 CGL-15 CGL-20 CGL-25 CGL-30 CGL-35 CGL-40 CGL-45 CGL-50 CGL-60 CGL-70 CGL-80 CGL-90 CGL-100 CGL-110 CGL-125 CGL-150 CGL-175 CGL-200 CGL-225 CGL-250 CGL-300 CGL-350 CGL-400 CGL-450 CGL-500 CGL-600 0.343" (8.71mm) 0.343 (8.71mm) 0.125" 3.00" (3.18mm) 0.75" (76.2mm) (19.05mm) 4.30" (109.22mm) 1.50" (38.1mm) 5.31" (134.87mm) CGL 110-200 0.19" (4.76mm) 1.0" 0.38" (25.4mm) (9.53mm) 1.0" (25.4mm) 3.0" 2.38" (76.2mm) (60.33mm) 5.25" (133.35mm) 8.19" (207.96mm) CGL 225-400 1.0" 0.41" (25.4mm) (10.32mm) 1.0" (25.4mm) .60" 3.0" (15.24mm) (76.2mm) 5.25" (133.35mm) 8.19" (207.96mm) CGL 450-600 Data Sheet: 4125 220 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 0.375" (9.53mm) 3.00" (76.2mm) IEC & British Standard Fuses HRCI Industrial Ceramic Body Fuses CIF21 HRCI-CA CIF06 HRCI-CB Specifications Description: The HRCI-CA fuse provides both overload and short-circuit protection to HRCI requirements. Offset blades for bolt-on mounting. CIF21 fuse fits the Cooper Bussmann CAMaster fuse holder (see data sheet 4132). Dimensions: See Dimensions illustration. Construction: Ceramic body. Ratings: Volts: -- 600Vac/250Vdc Amps: -- 1-30A IR: -- 200kA RMS Sym. Agency Information: CE, CSA C22.2, No. 106-M92. Mounting: Bolt-on. Specifications Description: A miniature industrial fuse that provides both short-circuit and overload protection and the CIF06 fits the 30A SAFEloc fuse holder. Dimensions: See Dimensions illustration. Construction: Ground ceramic body with plated end caps. Ratings: Volts: -- 600Vac/250Vdc Amps: -- 1-30A IR: -- 200kA RMS Sym. Agency Information: CE, CSA C22.2 No. 106-M92 (3-30A only). Mounting: Clip-in offset blades. Catalog Numbers Catalog Number Amp Ratings 1 3 6 10 15 20 25 30 Catalog Numbers 1CIF06 3CIF06 6CIF06 10CIF06 15CIF06 20CIF06 25CIF06 30CIF06 Features and Benefits * Close sizing to loads allows using smaller and less costly switches * Provides a higher degree of short-circuit protection * Helps protect motors against burnout from overloads Typical Applications * For use in circuits subject to surge currents such as those caused by motors, transformers and other inductive loads IEC & British Fuses Catalog Numbers 1CIF21 3CIF21 6CIF21 10CIF21 15CIF21 20CIF21 25CIF21 30CIF21 Amp Ratings 1 3 6 10 15 20 25 30 Features and Benefits * Close sizing to loads allows using smaller and less costly switches * Provides a higher degree of short-circuit protection * Helps protect motors against burnout from overloads Typical Applications * For use in circuits subject to surge currents such as those caused by motors, transformers and other inductive loads Dimensions - in (mm) Dimensions - in (mm) 2.15 (54.5) 1.44 (35.5) 0.19 (4.7) 0.54 (13.8) 2.38 (60.4) 1.44 (35.5) 0.44 (11.1) 0.54 (13.8) 0.5 (12.7) 0.03 (3.5) 1.75 (44.5) Data Sheet: 4127 0.03 (0.81) 0.14 (3.5) Data Sheet: 4128 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 221 IEC & British Standard Fuses HRCI-J Fast-acting Fuses Dimensions CJ HRCI-J Specifications Description: HRCI-J fast-acting fuses are industrial duty fuses with the excellent current-limiting characteristics of fast-acting HRCI-J fuses to limit damage to equipment and installations by the thermal and magnetic energy associated with a large short-circuit fault current. Overload characteristics limit cable damage due to low overload currents. Dimensions: See Catalog Numbers table and Dimensions illustrations. Construction: Ceramic body fuse. Ratings: Volts: -- 600Vac (or less), 250Vdc Amps: -- 1-600A IR: -- 200kA Agency Information: CSA C22.2 No. 106 M92; Designed to BS 88:2, IEC 60269-2. 1CJ to 60CJ A B B C 70CJ to 600CJ E J C A K F H D B G Catalog Numbers Catalog Numbers Catalog Numbers 1CJ 3CJ 6CJ 10CJ 15CJ 20CJ 25CJ 30CJ 35CJ 40CJ 45CJ 50CJ 60CJ 70CJ 80CJ 90CJ 100CJ 110CJ 125CJ 150CJ 175CJ 200CJ 225CJ 250CJ 300CJ 350CJ 400CJ 450CJ 500CJ 600CJ Amp Ratings 1 3 6 10 15 20 25 30 35 40 45 50 60 70 80 90 100 110 125 150 175 200 225 250 300 350 400 450 500 600 Dimensions in (mm) A B C D E F G H J K 2.25 (57) 0.5 (12.7) 0.81 (20.6) -- -- -- -- -- -- -- 2.38 (60) 0.63 (16) 1.06 (27) -- -- -- -- -- -- -- 4.63 (117) 3.63 (92) 1.13 (28) 0.75 (19) 0.13 (3.2) 1 (25.4) 0.5 (12.7) 0.28 (7.1) 0.38 (9.5) 2.63 (67) 5.75 (146) 4.38 (111) 1.63 (41) 1.13 (28.6) 0.19 (4.8) 1.38 (35) 0.69 (17.5) 0.28 (7.1) 0.38 (9.5) 3 (76) 7.13 (181) 5.25 (133) 2.13 (54) 1.63 (41) 0.25 (6.3) 1.88 (47.6) 0.94 (24) 0.41 (10.3) 0.53 (13.5) 3.38 (86) 8 (203) 6 (152) 2.63 (66) 2 (51) 0.38 (9.5) 2.13 (54) 1 (25.4) 0.53 (13.5) 0.69 (17.5) 3.75 (96) Data Sheet: 4129 222 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa IEC & British Standard Fuses HRCI - Miscellaneous Type K Fuses CIH, CIK & CIL HRCI-MISC Specifications Description: HRI fuses provide both overload and short-circuit protection, featuring offset blades for bolt down mounting. Dimensions: See Catalog Numbers table and Dimensions illustration. Construction: Ceramic body. Ratings: Volts: -- 600V Amps: -- 1-100A IR: -- 200kA@600V Agency Information: CE, CSA C22.2 No. 106 M92. Dimensions G J E IEC & British Fuses K F A D B L C H G (The CIL14 has a rejection hole, not a slot as shown above.) Catalog Numbers Catalog Amp Numbers Ratings 1CIH07 1 3CIH07 3 6CIH07 6 10CIH07 10 15CIH07 15 20CIH07 20 25CIH07 25 30CIH07 30 35CIK07 35 40CIK07 40 50CIK07 50 60CIK07 60 80CIL14 80 90CIL14 90 100CIL14 100 A Max 2.25 (57) B Max 0.94 (24) C Max 3.38 (86) D Nom 0.38 (9.2) Dimensions: in (mm) E Nom F Nom G Nom 0.04 (1.0) 2.88 (73) 0.21 (5.2) 2.25 (57) 0.94 (24) 3.38 (86) 0.38 (9.2) 0.04 (1.0) 2.28 (58) 1.06 (27) 3.56 (91) 0.5 (12.7) 0.05 (1.2) 2.28 (58) 1.06 (27) 3.56 (91) 0.5 (12.7) 0.05 (1.2) 2.75 (70) 2.75 (70) 1.44 (37) 1.44 (37) 4.38 (111) 4.38 (111) 0.75 (19) 0.75 (19) 0.09 (2.5) 0.09 (2.5) 3.69 (94) 3.69 (94) 2.88 (73) H Nom 0.31 (8) J Max 1 (25.4) K Nom 0.10 (2.6) L Max 2.38 (60) 1 (25.4) 0.10 (2.6) 2.38 (60) 0.21 (5.2) 0.31 (8) 2.88 (73) 0.21 (5.2) 0.41 (10.5) 1.09 (28) 0.13 (3.2) 2.38 (61) 2.88 (73) 0.21 (5.2) 0.41 (10.5) 1.09 (28) 0.13 (3.2) 2.38 (61) 0.34 (8.7) 0.34 (8.7) 0.41 (10.5) 0.41 (10.5) 1.5 (38.5) 1.5 (38.5) -- 2.91 (74) 2.91 (74) -- Recommended Fuse Holders Fuse 1-30A 35-60A Fuse Holder CM30CF CM60CF Data Sheet: 4130 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 223 IEC & British Standard Fuses HRC Form II Current-limiting Fuses Dimensions HRC Form II F Specifications Description: HRC Form II current-limiting fuses. Dimensions: See Catalog Numbers table and Dimensions illustrations. Construction: Ceramic body. Ratings: Volts: -- 600Vac (or less) -- 250Vdc Amps: -- 2-600A IR: -- 200kA RMS Sym. Agency Information: CE, CSA C22.2 No.106M1992; BS 88:2, IEC 60269:2. G J A D E H C F J E A G D B C C G B A H E K K F B A G P11C/R11C (Center Blades) D H E C Catalog Numbers 1.38 (35) L09C/M09C/P09C (Center Blades) D F A 1.38 (35) B 0.56 (14) 0.56 (14) C 3.38 (85) 3.38 (85) D 0.38 (9) Dimensions in (mm) E F 0.06 (1.2) 2.88 (73) G 0.22 (5.6) H 0.31 (8) 0.38 (9) J K 0.56 (14) -- 0.56 (14) CSA Category HRCII-C -- HRCII-C 3.44 (87) 3.44 (87) 0.06 (1.2) 2.88 (73) 0.22 (5.6) 0.31 (8) 0.5 (13) 0.06 (1.2) 2.88 (73) 0.22 (5.6) 0.31 (8) 2.19 (56) 0.88 (22) 2.19 (56) 2.19 (56) 0.88 (22) 0.88 (22) 3.75 3.75(95) (95) 0.5 (13) 0.5 (13) 0.06 (1.2) 2.88 (73) 0.22 (5.6) 0.31 (8) 2.38 2.38 (60) (60) 0.88 (21.4) (21.4) 0.88 4.38 (111) 0.56 (14.3) (14.3) 0.56 0.13 (3.2) (3.2) 0.13 3.69 (94) 0.34 (8.7) 2.56 (65) 2.56 (65) 1.5 (38) 1.5 (38) 4.38 (111) 0.75 (19) 0.75 (19) 0.09 (2.4) 0.09 (2.4) 3.69 (94) 0.34 (8.7) 2.38 2.38 (60) (60) 0.88 (21.4) (21.4) 0.88 5 5(127) (127) 0.56 0.56 (14) (14) 0.13 (3.2) 4.38 (111) 0.34 (8.7) 2.56 (65) 2.56 (65) 1.5 (38) 1.5 (38) 5.38 (136) 0.75 (19) 0.75 (19) 0.13 0.13 (3.2) (3.2) 4.38 (111) 0.34 (8.7) 0.34 (8.7) 3.06 (178) 2.31 (59) 5.38 (136) 1 (25.4) 0.19 (4.8) 4.38 (111) 4.38 (111) 0.34 (8.7) 3.19 (81) 3.19 (81) 2.31 (59) 2.31 (59) 2.88 (73) 2.88 (73) 8.25 (210) 8.25 (210) 8.25 (210) 1 (25.4) 1 (25.4) 0.19 (5) 1 (25.4) 0.25 (6.3) 0.25 (6.3) HRCII-MISC HRCII-MISC 0.44 (11) 11 (25.4) (25.4) ---- HRCII-C HRCII-C 0.44 (11) 0.44 (11) -- -- -- HRCII-MISC -- 0.44 (11) ---- ---- HRCII-MISC HRCII-MISC 0.56 (14) 0.56 (14) -- -- -- HRCII-C HRCII-C 0.5 (13) -- -- 0.5 (13) 0.19 (4.8) 3.06 (178) 3.06 (178) 0.88 (22) -- -- 0.88 (22) 0.88 (22) -- -- 5.25 (133) 0.41 (10) 0.63 (16) 5.25 (133) 5.25 (133) 0.41 (10) 0.41 (10) 0.63 (16) 0.63 (16) For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa -- -- -- 0.19 (5) Data Sheet: 4131 224 K07C/K07CR/ L14C/M14C (Offset Blades) H Typical Applications * Used to protect motor control circuits, together with contactors and overload protection relays to provide Type 2 coordination - per IEC 60947-4. Catalog Amp Numbers Ratings 2H07C 2 4H07C 4 6H07C 6 10H07C 10 15H07C 15 20H07C 20 25H07C 25 30H07C 30 40K07C 40 50K07C 50 60K07C 60 80K07CR 80 100K07CR 100 80L14C 80 100L14C 100 125M14C 125 150M14C 150 200M14C 200 80L09C 80 100L09C 100 125M09C 125 150M09C 150 200M09C 200 250P09C 250 300P09C 300 350P09C 350 400P09C 400 250P11C 250 300P11C 300 350P11C 350 400P11C 400 450R11C 450 500R11C 500 600R11C 600 H07C (Offset Blades) B -- 1 (25) -- 1 (25) -- 1 (25) 1 (25) -- HRCII-C HRCII-MISC HRCII-MISC HRCII-C HRCII-C HRCII-C IEC & British Standard Fuses BS 88 British Standard Low Voltage Fuses SSD, NSD, ESD BS 88 Part 1 Specifications Description: The NSD and ESD are low voltage fuses complying with general purpose gG characteristics. Construction: Ceramic body. Ratings: Volts: -- 240-550Vac (See Catalog Numbers table) Amps: -- 2-63A (See Catalog Numbers table) -- 20M25-63M100A Motor Starter ratings (See Catalog Numbers table) IR: -- 33kA (SSD) -- 80kA (NSD, ESD) Agency Information: CE, Meets the requirements of BS 88 Part 1 and IEC 60269-1. Mounting: Offset blades. ESD Amp Ratings 2, 4, 6, 10, 16, 20, 25, 32 2, 4, 6, 10, 16, 20, 25, 32, 20M25*, 20M32*, 20M36*, 32M36*, 32M40*, 32M50*, 32M63* 2, 4, 6, 10, 16, 25, 32 40, 50, 63, 63M80, 63M100* Max AC Voltage Ratings 240 550 415 415 550 415 BS 88 Ref. E1 F1 F1 F1 F2 F2 *"M" indicates motor starter ratings. To Order To order, specify Basic Catalog Number and amp rating. Example: SSD-20 Recommended Fuse Holders Basic Fuse Catalog Numbers NSD ESD Holder Catalog Numbers 32NNSF 63ENSF Specifications Description: The STD to DEO types are low voltage fuses complying with general purpose gG characteristics. Construction: Ceramic body. Ratings: Volts: -- 240-550Vac (See Catalog Numbers table) Amps: -- 2-200A (See Catalog Numbers table) -- 20M25-200M315A Motor Starter ratings (See Catalog Numbers table) IR: -- 33kA (STD) -- 80kA (NITD, AAO, BAO, CEO, DEO) Agency Information: CE, Meets the requirements of BS 88 Part 1 and IEC 60269-1. Mounting: Offset bolted blades. IEC & British Fuses Basic Catalog Numbers Basic Catalog Numbers SSD NSD STD, NITD, AAO, BAO, OSD, CEO, DEO BS 88 Part 1 Typical Applications * The STD type are used in 240V street lighting cut-outs. * NITD to DEO types used for industrial and general purpose applications Basic Catalog Numbers Basic Catalog Numbers STD NITD AAO BAO CEO DEO OSD Amp Ratings 2, 4, 6, 10, 16, 20, 25, 32 2, 4, 6, 10, 16, 20, 25, 32 20M25*, 20M32*, 32M40*, 32M50*, 32M63* 2, 4, 6, 10, 16, 20, 25, 32, 32M40*, 32M50*, 32M63* 40, 50, 63, 63M80*, 63M100* 32, 40, 50, 63, 80, 100 100M125*, 100M160*, 100M200* 125, 160, 200, 200M250*, 200M315* 80, 100 100M125*, 100M160* Max AC Voltage BS 88 Ratings Ref. 240 -- 550 -- 415 -- 550 -- 550 A3 550 A4 415 A4 415 -- 550 -- 415 -- *"M" indicates motor starter ratings. To Order To order, specify Basic Catalog Number and amp rating. Example: BAO-16 Recommended Fuse Blocks & Holders Basic Fuse Catalog Numbers NITD AAO BAO OSD CEO Data Sheets 4105 (SSD), 4100 (NSD) and 4101 (ESD) Block/Holder Catalog Numbers CM32FC CM32F CM63F CM100F BH-0111 Data Sheets 4123 (STD), 4106 (NITD), 4109 (AAO), 4112 (BAO), 4107 (OSD), 4115 (CEO) and 4117 (DEO) For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 225 IEC & British Standard Fuses BS 88 British Standard Low Voltage Fuses AC, AD, BC, BD, CD, DD, ED, EFS BS 88 Specifications Description: Low voltage fuses that comply with general purpose gG characteristics and available up to 400A with two hole mount and up to 1250A with four hole mount. Construction: Ceramic body. Ratings: Volts: -- 415/550Vac, 250Vdc (See Catalog Numbers table) Amps: -- 2-400A (See Catalog Numbers table) -- 63M80-400M500A Motor Starter ratings (See Catalog Numbers table) IR: -- See Catalog Numbers table Agency Information: CE, Meets the requirements of BS 88 Parts 1 and 2 and IEC 60269-1. Mounting: Center bolted blades, two-hole mount. Specifications Description: Low voltage fuses complying with general purpose gG characteristics and available up to 400A with two hole mount and up to 1250A with four hole mount. Construction: Ceramic body. Ratings: Volts: -- 415/550Vac, 250/400Vdc (See Catalog Numbers table for details) Amps: -- 355-1250 IR: -- See Catalog Numbers table Agency Information: CE, Meets the requirements of BS 88 Parts 1 and 2 and IEC269-1. Mounting: Center bolted blades, four-hole mount. Basic Catalog Numbers Basic Catalog Numbers Basic Catalog Numbers AC AD BC BD CD DD ED EFS Amp Ratings 2, 4, 6, 10, 16, 20, 25, 32 2, 4, 6, 10, 16, 20, 25, 32 40, 50, 63 63M80*, 63M100* 40, 50, 63 80, 100, 100M125*, 100M160*, 100M200*, 100M200* 125, 160, 200, 200M250*, 200M315* 250, 315, 355, 400, 315M400* 400M500* 125, 160, 200, 250, 315 Interrupting Ratings AC DC 80kA 40kA 80kA 40kA 80kA 40kA 80kA -- 80kA 40kA 80kA -- Max Voltage Ratings BS 88 AC DC Ref. 550 250 -- 550 250 -- 550 250 -- 550 -- -- 550 250 -- 415 -- EF, FF, FG, GF, GG, GH BS 88 B1 80kA -- 415 -- B2 80kA 80kA 80kA -- -- 415 550 415 -- -- -- B3 B4 -- Basic Catalog Numbers EF Interrupting Max Voltage Amp Ratings Ratings BS 88 Ratings AC DC AC DC Ref. 355, 400 80kA -- 415 -- C1 400M500* 80kA -- 550 -- -- FF 450, 500, 560, 630 80kA 40kA 550 400 C2 FG 450, 500, 560, 630 80kA 40kA 550 400 -- GF 710, 800 80kA 40kA 550 250 C3 GG 710, 800 80kA 40kA 550 250 -- 1000, 1250 80kA -- 550 -- -- GH 710, 800, 1000, 1250 80kA -- 550 -- -- *"M" indicates motor starter ratings.*"M" indicates motor starter ratings. To Order To order, specify Basic Catalog Number and amp rating. Example: FG-450 *"M" indicates motor starter ratings. To Order To order, specify Basic Catalog Number and amp rating. Example: BC-40 Recommended Fuse Blocks & Holder Basic Fuse Catalog Numbers AC AD BC BD CD DD ED Block/Holder Catalog Numbers BH-0111 Modular fuse block 200DF Fuse holder BH-0111 Modular fuse block 200DF Fuse holder 200DF Fuse holder 200DF Fuse holder BH-1131 Modular fuse block Data Sheets 4110 (AC), 4111 (AD), 4113 (BC), 4114 (BD), 4116 (CD), 4118 (DD), 4119 (ED) and 4121 (EFS) 226 Data Sheets 4120 (EF), 4102 (FF), 4122 (FG), 4103 (GF), 4104 (GG) and 4108 (GH) For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa IEC & British Standard Fuses DIN Style Type D and Neozed Low Voltage Fuses D16, D27, D33, D125 Type D NZ01, NZ02 Type D0 Specifications Description: DIN style Type D low voltage fuses. Dimensions: See Catalog Numbers table and Dimensions illustrations. Construction: Ceramic body. Ratings: Volts: -- 500Vac Amps: -- 2-100A IR: -- 100kA Agency Information: CE, "D" type fuses complying with DIN 49360 Part 2 and DIN 49515, operating class gL. Catalog Numbers Amp Ratings 2 4 6 10 16 20 25 2 4 6 10 16 20 25 35 50 63 80 100 Dimension "D" (mm) 6 6 6 8 10 12 14 6 6 6 8 10 12 14 16 18 20 5 7 Color Code Pink Brown Green Red Grey Blue Yellow Pink Brown Green Red Grey Blue Yellow Black White Copper Silver Red Figure Number 1 2 Catalog Numbers 2NZ01 4NZ01 6NZ01 10NZ01 16NZ01 20NZ02 25NZ02 35NZ02 50NZ02 63NZ02 Amp Ratings 2 4 6 10 16 20 25 35 50 63 Dimension "D" (mm) 11 11 11 11 11 15 15 15 15 15 Color Code Pink Brown Green Red Grey Blue Yellow Black White Copper IEC & British Fuses Catalog Numbers 2D16 4D16 6D16 10D16 16D16 20D16 25D16 2D27 4D27 6D27 10D27 16D27 20D27 25D27 35D33 50D33 63D33 80D125 100D125 Specifications Description: Low voltage Neozed fuses suitable for use on 250Vdc systems. Dimensions: See Catalog Numbers table and Dimensions illustration. Construction: Ceramic body. Ratings: Volts: -- 400Vac Amps: -- 2-63A IR: -- 100kA Agency Information: CE Catalog Numbers Dimensions (mm) D 3 4 36 Additional Fuselinks: Quick acting fuselinks in body sized D16, D27, D33 and D125 rated 2-100A. Reference number suffixed Q, i.e. 10D27Q. Voltage rating 500V. Gauge rings and keys can also be supplied. Dimensions (mm) Figure 1 Figure 2 Data Sheet: 4124 Figure 3 Figure 4 Data Sheet: 4124 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 227 IEC & British Standard Fuses NH HRC Fuses Ratings: ___NHG___B Volts: -- 500Vac/250Vdc -- 690Vac/250Vdc Amps: -- 2-1250A IR: -- 120kA Frequency: -- 50Hz Operating Frequency: -- 45-62Hz Agency Information: IEC 60269, VDE0636, DIN 43620 Part 1 to 4, VDE Mark and CE. Specifications Class: gG/gL Description: DIN square bodied, dual indication industrial fuses. Construction: Steatite insulator, corrosionproof (aluminum) metal parts with full-contact, silver-plated copper blades. Sizes: DIN 000 to 4. Selectivity Ratio: 1:1.6 up to 500Vac. Fuse Blocks SB00-D SB1-D SB2-D Size 000-00 1*, 1 02, 2, 03, 3 Dimensions (mm) Fuse Size 000 00 0 01 1 02 2 03 3 4 a1 78.5 1.5 78.5 1.5 125 2.5 135 2.5 135 2.5 150 2.5 150 2.5 150 3 150 3 200 a2 (max) 54 54 68 75 75 75 75 75 75 84 45 45 62 62 62 62 62 62 62 80 a3 1.5 1.5 +3/-1.5 2.5 2.5 2.5 2.5 2.5 2.5 a4 49 1.5 49 1.5 68 +1.5/-3 68 2.5 68 2.5 68 2.5 68 2.5 68 2.5 68 2.5 90 b (nom) 15 15 15 15 20 20 25 25 32 50 c1 ( 8) 35 35 35 40 40 48 48 60 60 85 c2 (nom) 10 11 11 11 11 11 11 11 11 11 D (nom) 2 0.5 7.0 0.5 2.5 0.5 2.5 0.5 2.5 0.5 2.5 0.5 2.5 0.5 2.5 0.5 3.0 0.5 3 e1 (max) 41 48 48 48 53 53 61 61 75 120 e2 (max) 21 30 30 30 52 52 60 60 70 87 e3 (max) 16 25 25 25 25 25 25 25 25 -- Data Sheet 4173 228 For detailed information, visit the Electrical IEC section at www.cooperbussmann.com e4 (nom) 6 6 6 6 6 6 6 6 6 8 f (max) 8 15 15 15 15 15 15 15 18 30 IEC & British Standard Fuses NH HRC Fuses 500Vac / 250Vdc Size 000 00 01 1 02 2 03 3 4 Single Indicator Slotted End Tags 2 4 6 10 16 20 25 32 35 40 50 63 80 100 125 160 10 16 20 25 32 35 40 50 63 80 100 125 160 10 16 20 25 32 35 40 50 63 80 100 125 160 200 224 250 35 40 50 63 80 100 125 160 200 224 250 315 355 400 250 315 355 400 500 630 500 630 800 1000 1250 gG/gL Dual Indicator Voltage Conducting Carton Metal Gripping Lugs Quantity 2NHG000B 4NHG000B 6NHG000B 10NHG000B 16NHG000B 20NHG000B 25NHG000B 32NHG000B 35NHG000B 40NHG000B 50NHG000B 63NHG000B 80NHG000B 100NHG000B 125NHG00B 160NHG00B 10NHG0B 16NHG0B 20NHG0B 25NHG0B 32NHG0B 35NHG0B 40NHG0B 50NHG0B 63NHG0B 80NHG0B 100NHG0B 125NHG0B 160NHG0B 10NHG01B 16NHG01B 20NHG01B 25NHG01B 32NHG01B 35NHG01B 40NHG01B 50NHG01B 63NHG01B 80NHG01B 100NHG01B 125NHG01B 160NHG01B 200NHG1B 224NHG1B 250NHG1B 35NHG02B 40NHG02B 50NHG02B 63NHG02B 80NHG02B 100NHG02B 125NHG02B 160NHG02B 200NHG02B 224NHG02B 250NHG02B 315NHG2B 355NHG2B 400NHG2B 250NHG03B 315NHG03B 355NHG03B 400NHG03B 500NHG3B 630NHG3B 500NHG4G 630NHG4G 800NHG4G 1000NHG4G 1250NHG4G 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 1 1 1 1 1 For detailed information, visit the Electrical IEC section at www.cooperbussmann.com IEC & British Fuses 0 Rated Current (Amps) 229 IEC & British Standard Fuses NH HRC Fuses 690Vac / 250Vdc Size 000 00 0 1 2 3 230 Rated Current (Amps) 2 4 6 10 16 20 25 32 35 40 50 63 80 100 6 10 16 20 25 32 35 40 50 63 80 100 50 63 80 100 125 160 200 63 80 100 125 160 200 224 250 315 250 315 355 400 425 500 gG/gL Dual Indicator Voltage Conducting Carton Metal Gripping Lugs Quantity 2NHG000B-690 4NHG000B-690 6NHG000B-690 10NHG000B-690 16NHG000B-690 20NHG000B-690 25NHG000B-690 32NHG000B-690 35NHG000B-690 40NHG000B-690 50NHG00B-690 63NHG00B-690 80NHG00B-690 100NHG00B-690 6NHG0B-690 10NHG0B-690 16NHG0B-690 20NHG0B-690 25NHG0B-690 32NHG0B-690 35NHG0B-690 40NHG0B-690 50NHG0B-690 63NHG0B-690 80NHG0B-690 100NHG0B-690 50NHG1B-690 63NHG1B-690 80NHG1B-690 100NHG1B-690 125NHG1B-690 160NHG1B-690 200NHG1B-690 63NHG2B-690 80NHG2B-690 100NHG2B-690 125NHG2B-690 160NHG2B-690 200NHG2B-690 224NHG2B-690 250NHG2B-690 315NHG2B-690 250NHG3B-690 315NHG3B-690 355NHG3B-690 400NHG3B-690 425NHG3B-690 500NHG3B-690 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 For detailed information, visit the Electrical IEC section at www.cooperbussmann.com IEC & British Standard Fuses NH Fuse Bases SB*-D, SB*-S Up to 690V / 160 - 1250A Sizes 00, 0, 1, 2, 3, 4 Part Numbers Size Poles 1 3 160A 0 1 3 160A 1 1 3 Ratings: 2 DIN Screw Carton Compatible Quantity Fuse Size SB00-D TB00-D 000 & 00 SB0-D TB0-D 3 1 0 250A SB1-D TB1-D 3 1 01 & 1 1 3 400A SB2-D TB2-D 3 1 02 & 2 3 1 3 630A SB3-D TB3-D 3 1 03 & 3 4 1 1250A SB4-S (Screw Connection only) 3 4 * Voltage: up to 690Vac * Amps: 2 to 1250A Applications: Protection of industrial circuits and electrical apparatus Part Numbers 3 1 00 Description: NH fuse bases with thermoplastic bodies. DIN rail and screw mounting (size 4 screw fix). Range of protection accesories for live parts in order to obtain IP20 protection standard. Current (Amps) TB00-D-IP20 Standards and Approvals: IEC 60269, DIN 43620 Size Current (Amps) Part Ref NH00 160 SL00 NH0 160 SL0 NH1 250 SL1 NH2 400 SL2 NH3 630 SL3 NH4 1000 SL4 IEC & British Fuses Neutral Carton Quantity 3 Fuse extraction handle Size Part Ref Carton Quantity C00-3 FEH 1 Protection accessories Size Current (Amps) NH00* NH0 NH1 NH2 NH3 160A 160A 250A 400A 630A Separation Partition 4 Fuse Casing 5 Terminal Cover 1 Separator 3 Part Ref Carton Quantity Part Ref Carton Quantity Part Ref Carton Quantity Part Ref Carton Quantity SP00* SP0 SP1-2 SP1-2 SP3 2 2 2 2 2 FC00* FC0 FC1-2 FC1-2 FC3 3 3 3 3 3 CS00* CS0 CS1 CS2 CS3 6 6 6 6 6 BC00* BC0 BC1-2 BC1-2 BC3 2 2 2 2 2 * For single pole only IP Protection Kits Microswitch Part Reference Description TB00-D-IP20 Complete triple pole fuse base IP20 rated FPK0-3P IP20 kit for TB0-D fuse base FPK1-3P IP20 kit for TB1-D fuse base FPK2-3P IP20 kit for TB2-D fuse base FPK3-3P IP20 kit for TB3-D fuse base Part Ref Carton Quantity BVL-50 1 Microswitch suitable for the following NH Fuse links: - 400 Volts gG/gL - 500 Volts gG/gL and aM - 690 Volts gG/gL and aM For detailed information, visit the Electrical IEC section at www.cooperbussmann.com 231 IEC & British Standard Fuses Class gG/gL IEC 60269 Industrial Ferrule Fuses 8 x 31mm: 400Vac, 0.5 - 25A 10 x 38mm: 500Vac, 0.5 - 32A 14 x 51mm: 400Vac - 500Vac - 690Vac, 1 - 50A 22 x 58mm: 400Vac - 500Vac - 690Vac, 2 - 125A 232 For detailed information, visit the Electrical IEC section at www.cooperbussmann.com IEC & British Standard Fuses Class aM IEC Industrial Ferrule Fuses - Class aM IEC 60269 8 x 31mm: 400Vac, 1 - 8A 10 x 38mm: 400Vac - 550Vac, 0.16 - 25A IEC & British Fuses 14 x 51mm: 690Vac - 500Vac, 0.25 - 50A 22 x 58mm: 400Vac - 500Vac - 690Vac, 2 - 125A Neutral Links For detailed information, visit the Electrical IEC section at www.cooperbussmann.com 233 IEC & British Standard Fuses Class aM & gG/gL IEC Industrial Ferrule Fuses with Striker Class gG/gL with Striker 14 X 51 22 X 58 Catalog Number With Striker C14G2S C14G4S C14G6S C14G8S C14G10S C14G12S C14G16S C14G20S C14G25S C14G32S C14G40S C14G50S Catalog Number With Striker C22G4S C22G6S C22G8S C22G10S C22G12S C22G16S C22G20S C22G25S C22G32S C22G40S C22G50S C22G63S C22G80S C22G100S C22G125S Amp Rating 2 4 6 8 10 12 16 20 25 32 40 50 Amp Rating 4 6 8 10 12 16 20 25 32 40 50 63 80 100 125 Watts Loss (W) 0.24 0.45 0.42 0.70 0.53 0.88 1.16 1.23 1.46 2.04 3.34 3.04 Watts Loss (W) 0.48 0.47 0.73 0.74 0.83 1.21 1.29 1.53 2.13 3.40 3.48 4.46 5.86 6.61 8.42 Voltage (AC) 500 500 400 Voltage (AC) 690 Interrupting Rating (kA) 120 120 Interrupting Rating (kA) 80 690 80 500 500 120 120 400 Class aM with Striker 14 X 51 22 X 58 234 Catalog Number With Striker C14M1S C14M2S C14M4S C14M6S C14M8S C14M10S C14M12S C14M16S C14M20S C14M25S C14M32S C14M40S C14M50S Catalog Number With Striker C22M2S C22M4S C22M6S C22M8S C22M10S C22M12S C22M16S C22M20S C22M25S C22M32S C22M40S C22M50S C22M63S C22M80S C22M100S C22M125S Amp Rating 1 2 4 6 8 10 12 16 20 25 32 40 50 Amp Rating 2 4 6 8 10 12 16 20 25 32 40 50 63 80 100 125 Watts Loss (W) 0.14 0.24 0.45 0.42 0.70 0.53 0.88 1.16 1.23 1.46 2.04 3.34 3.04 Watts Loss (W) 0.29 0.48 0.47 0.73 0.74 0.83 1.21 1.29 1.53 2.13 3.40 3.48 4.46 5.86 6.61 8.42 Voltage (AC) 500 500 400 Voltage (AC) 690 Interrupting Rating (kA) 120 120 Interrupting Rating (kA) 80 690 80 500 500 400 120 120 For detailed information, visit the Electrical IEC section at www.cooperbussmann.com IEC & British Standard Fuses HRC Fuse Holders SAFEloc Specifications Catalog Symbol: See table below. Description: The CAMaster HRC fuse holder features a unique cam-action for easy fuse removal while allowing significantly improved contact pressure between fuse carrier and base contact that enhances electrical performance. A range of lockable safety carriers for the fuse holder (catalog reference: LSC), are available. Ratings: Volts: -- 690V Amps: -- 30-100A (See Catalog Number table for details) Agency Information: CE, CSA C22.2 No. 39; IEC 269 AND BS 88. Mounting: 35mm DIN-rail or single screw mounting. Specifications Catalog Symbol: See table below. Description: The SAFEloc HRC fuse holders (for use with HRCI-CB fuses) provides a positive, stressfree fuse fitting and locks it in position to ensure safe insertion and withdrawal from the base. Base contacts are fully shrouded to help protect against electric shock. Shrouds utilize simple slide/snap action allowing access to the contact terminal screws. Ratings: Volts: -- 600V Amps: -- 30-60A (See Catalog Number table for details) Agency Information: CE, Designed to accommodate the compact range of offset blade fuse to CSA C22.2 No. 106, HRCI-CB. Mounting: 35mm DIN rail or single screw mounting. Catalog Numbers Catalog Numbers CM20CF CM30CF CM60CF CM100CF Amp Ratings 30 30 60 100 Details For: HRCI-CA Applications HRCII Applications Fuse Accepted _CIF21 _H07C _K07C _K07CR Accessory Catalog Numbers for CAMaster Units Catalog Numbers 20BS 32BS 60/100BS GLP NI 20LSC 30LSC 60/100LSC Amp Ratings 30 30 60/100 All All 30 30 60/100A Data Sheet: 4132 Details Back Stud Ganging Link Kit 660V Neon Indicator Security Carrier with Clip Fuse Holder Accepted CM20CF CM30CF CM60/100CF 3-Pole -- CM20CF CM30CF CM60/100CF Catalog Numbers* Catalog Amp Numbers Ratings Connection C30F Front C30BS 30 Back C30FBS Front-Back C60F Front C60BS 60 Back C60FBS Front-Back *For use with HRCI-CB Fuses. Fuse Accepted _CIF06 EK-Amp Data Sheet: 4133 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 235 IEC & British Fuses CAMaster 236