(c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets SENTRON Configuration Manual Edition 10/2015 siemens.com/lowvoltage (c) Siemens AG 2015 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets 2 Introduction 3 4AC3 bell transformers 5 4AC3 safety transformers 7 4AC2 power supply units 9 5TE6 REG socket outlets For further technical product information: Siemens Industry Online Support: www.siemens.com/lowvoltage/productsupport. Entry type: Application example Certificate Characteristic Download FAQ Manual Product note Software archive Technical data Siemens * 10/2015 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets Introduction Overview Page Application Standards Used in 4AC3 bell transformers 3 Power supply up to 18 VA as safety extra-low EN 61558-1 voltage (SELV) in residential buildings for the EN 61558-2-8 supply of gongs, buzzers, bells, door openers and remote control switches -- 4AC3 safety transformers 5 Power supply up to 63 VA as safety extra-low EN 61558-1 voltage (SELV) for the supply of control EN 61558-2-6 circuits, switching relays and Insta contactors -- 4AC2 power supply units 7 Direct voltage power supply up to 24 V DC EN 61558-2-6 and 2 A as safety extra-low voltage (SELV) for the supply of gongs, buzzers, bells, door openers, switching relays and Insta contactors 5TE6 REG socket outlets 9 For power supply during maintenance in distribution boards in DIN VDE, CEE 7, CEI 23-50 and UL 489 versions Non-residential buildings Residential buildings Industry Devices 2 Siemens * 10/2015 DIN VDE 0620-1, CEE 7 standard sheet V, CEI 23-50, UL 498 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets 4AC3 bell transformers Overview A typical application for these bell transformers is short-time use, as occurs with bells, gongs, door openers or remote control switches in residential buildings. After a short circuit, the primary current must be briefly disconnected from the mains before restarting. Higher output voltages will occur in the event of low-load or no-load operation. Siemens bell transformers are protected against short-circuit or moderate overload by a PTC resistor. Technical specifications 4AC3208-0 4AC3208-1 4AC3214-0 4AC3218-0 EN 61558-1:2005, EN 61558-2-8:2010 Standards Rated operational power Ps VA Rated operational voltage Ue V AC 230 8 8 14 18 Operating range at 50 Hz xUe 1.04 Rated frequency Hz 50 V AC V AC V AC V AC -8 --- -8 12 -- -8 12 24 4 8 Rated secondary current Isec * At 4 V * At 8 V * At 12 V * At 24 V A AC A AC A AC A AC -1.0 --- -1.0 0.6 -- -2.0 1.3 0.6 2.0 2.0 1.5 -- Rated power dissipation PV * In no-load operation * At a rated voltage of 4 V * At a rated voltage of 8 V * At a rated voltage of 12 V * At a rated voltage of 24 V W W W W W 1.2 -5.7 --- 1.2 -5.7 3.8 -- 1.3 -10.5 7.4 4.2 1.3 5.5 8.1 8.4 -- Safe separation * Creepage distances and clearances mm >6 35 40 40 Rated secondary voltage Usec -- E Insulation class Test voltage, 50 Hz, 1 second * Primary against secondary winding kV 4 Conductor cross-sections * Rigid * Flexible, with end sleeve mm2 mm2 1 x 4 or 2 x 2.5 1 x 2.5 or 2 x 1.5 Permissible ambient temperature C 40 Permissible humidity % 91 Degree of protection Acc. to EN 60629 IP20 Safety class Acc. to EN 61140 (VDE 0140-1) II Siemens * 10/2015 3 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets 4AC3 bell transformers Dimensional drawings 44 37 60 i202_18271 90 45 12 5 4AC32 Circuit diagrams 8 4AC3208-0 4 230 V AC 50Hz 8V 4 6 12V 4AC3208-1 Siemens * 10/2015 7 8 1 230 V AC 50Hz 8V 4 12V 6 24V 4AC3214-0 1 7 8 230 V AC 50Hz 4V 4 7 8V 6 12V 4AC3218-0 8 I201_18472 8V 1 I201_18471 4 7 I201_18470 230 V AC 50Hz I201_18469 1 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets 4AC3 safety transformers Overview These transformers up to 63 VA provide a safety extra-low voltage for supplying control circuits, switching relays or Insta contactors in continuous operation as alternating voltage power supply for 8 V, 12 V, 16 V, 24 V and 32 V AC. Higher output voltages will occur in the event of low-load or no-load operation. Siemens safety transformers are protected against short circuit or moderate overload by a PTC resistor. After a short circuit, the primary current must be briefly disconnected from the mains before restarting. Technical specifications 4AC3716-0 4AC3724-0 4AC3740-0 4AC3740-1 4AC3763-0 EN 61558-1:2005, EN 61558-2-6:2009 Standards Rated operational power Ps VA Rated operational voltage Ue V AC 230 16 24 40 40 63 Operating range at 50 Hz xUe 1.04 Rated frequency Hz 50 V AC V AC V AC V AC V AC V AC 8 ------ 8 -12 ---- -12 --24 -- -12 -16 24 32 -2 x 12 --24 -- Rated secondary current Isec * At 8 V * At 12 V * At 16 V * At 24 V * At 32 V A AC A AC A AC A AC A AC 2.0 ----- 2.0 2.0 ---- -3.3 -1.6 -- -3.3 2.5 1.6 1.2 -5.2 -2.6 -- Rated power dissipation PV * In no-load operation * At a rated voltage of 8 V * At a rated voltage of 12 V * at a rated voltage of 16 V * At a rated voltage of 24 V * at a rated voltage of 32 V W W W W W W 1.1 6.8 ----- 1.1 4.6 7.6 ---- 3.5 -7.1 -7.7 -- 3.9 -7.5 7.7 8.1 7.6 3.9 -13.2 -13.5 -- Safe separation * Creepage distances and clearances mm >6 Rated secondary voltage Usec E Insulation class Test voltage, 50 Hz, 1 second * Primary against secondary winding kV 4 Conductor cross-sections * Rigid * Flexible, with end sleeve mm2 mm2 1 x 4 or 2 x 2.5 1 x 2.5 or 2 x 1.5 Permissible ambient temperature C 25 Permissible humidity % 91 Degree of protection Acc. to EN 60529 IP20 Safety class Acc. to EN 61140 (VDE 0140-1) II F Siemens * 10/2015 5 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets 4AC3 safety transformers Dimensional drawings 44 37 60 44 54 12 i202_18267 i202_18274 90 90 45 45 12 60 5 5 4AC3716-0 4AC3724-0 44 90 60 i202_18273 90 45 12 5 4AC3740-1 4AC3740-0 4AC3763-0 Circuit diagrams 4AC3716-0 6 7 8V 4 6 12V 4AC3724-0 8 1 6 8 10 12V 12 6 4AC3740-0 Siemens * 10/2015 230 V AC 50Hz 8 10 24V 11 12 1 6 8 10 12 12V 4AC3740-1 6 8 10 12 24V 2 4 10 16V 12 2 230 V AC 50Hz 4 10 32V 11 12 1 6 8 10 12V 12 6 4AC3763-0 230 V AC 50Hz 8 10 24V 11 12 I201_18475 8 230 V AC 50Hz I201_18477 8V 1 I201_18476 4 7 I201_18474 230 V AC 50Hz I201_18473 1 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets 4AC2 power supply units Overview The electronic power supply unit provides a 24 V DC supply to systems with an operational voltage of 85 to 265 V AC or 85 to 300 V DC. The device operates in the lower class for minimum power supply with a safety extra-low voltage (SELV). The electronic power supply unit is suitable for supplying the 5TT71 GSM alarm modules within a supply voltage range of 150 to 230 V AC. Technical specifications 4AC2402 EN 60068-2, EN 61558-1, EN 61000-4 Standards -- Approvals Rated operational power Ps W 8.4 Rated operational voltage Ue V AC V DC 85 ... 265 85 ... 300 Permissible operational voltage For the 5TT71 GSM alarm modules V AC/DC 150 ... 265 x Ue -- Rated frequency Hz 50/60 Operating frequency range Hz -- Rated secondary voltage Usec V DC 24 5 % Rated secondary current Isec A DC 0.35 Primary operating range At 50/60 Hz Electronic overload protection Current limitation Residual ripple Rated power dissipation Pv In no-load operation At rated load Hum-free Core molded Safe separation Creepage distances and clearances mV < 100 W W ---- mm -- Insulation class Test voltage Primary against secondary winding > 5.5 50 Hz, 1 min Insulation resistance kV -- kV 4 6 kV/2 Rated impulse withstand voltage/ degree of pollution Acc. to IEC 60664-1 Static discharge Acc. to IEC/EN 61000-4-2 kV 8 RF irradiation Acc. to IEC/EN 61000-4-3 V/m 10 Transient overvoltage (burst) Acc. to IEC/EN 61000-4-4 kV 4 Transient overvoltage (surge) * Supply lines A1, A2 * A1/A2 and ground Acc. to IEC/EN 61000-4-5 kV kV 1 2 RF, conducted disturbance Acc. to IEC/EN 61000-4-6 V 10 Interference suppression to lower limit class Acc. to EN 61000-6-3 Complied with Terminals * Screw (slotted-head) * screw (Pozidriv) M2.5 -- Conductor cross-sections * Rigid * Flexible, with end sleeve, min. mm2 mm2 0.5 ... 2.5 0.5 ... 1.5 Permissible ambient temperature C -20 ... +60 Permissible humidity % Resistance to climate Acc. to IEC/EN 60068-1 Resistance to vibrations Frequency 10 ... 55 Hz Acc. to IEC/EN 60068-2-6 20/045/04 Degree of protection Acc. to EN 60529 IP20, with connected conductors Safety class Acc. to EN 61140 II mm 0.35 amplitude Siemens * 10/2015 7 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets 4AC2 power supply units Dimensional drawings I201_13709a 45 64 90 A1+A2 A2 US+ US- US- 36 7 25 44 4AC2402 Circuit diagrams Graphical symbols I201_13710b A1 A2 Us+ Us4AC2402 8 Siemens * 10/2015 64 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets 5TE6 REG socket outlets Overview The socket outlets for mounting in distribution boards to DIN 43880 and on standard mounting rails to DIN 60715 have since become standard in modern switchgear assemblies/distribution boards. The socket outlet range complies with a number of different standards and is available according to the standards of the following countries: VDE for Germany, CEE7 for Belgium/France, CEI for Italy and UL for USA. In distribution boards with 55 mm mounting depth the socket outlet can only be used without the hinged lid. The lids can be retrofitted on all devices. In system components where equipment is still live even after the main switch has been disconnected, this must be indicated according to DIN EN 50110-1 (VDE 0105-1) and IEC/EN 60204-1/VDE 0113-1. Yellow socket outlets are used for these applications. Technical specifications 5TE6800 5TE6801 5TE6810 5TE6802 5TE6803 5TE6804 Standards VDE 0620-1 VDE 0620-1 VDE 0620-1 CEI 23-50 CEE 7 standard sheet V UL 498 Approvals VDE 0620-1 -- UL File No. E258598/ CSA C22.2 No. 182.3M Rated operational voltage Ue V AC 230 125 Rated operational current Ie A AC 16 15 PZ1 Terminals screw (Pozidriv) Terminal tightening torque, max. N 1.2 Stripped length mm 10 Conductor cross-sections * Rigid * Flexible, with end sleeve * Rigid * Flexible mm2 mm2 AWG AWG 1.5 ... 6 0.5 ... 4 10 ... 14 14 Permissible ambient temperature C -10 ... +55 Degree of protection Acc. to EN 60529 IP20, with connected conductors Mounting position Without cover: any, with cover: vertical or horizontal Siemens * 10/2015 9 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets 5TE6 REG socket outlets L 44 7 24 N I201_12118 N I201_12115 44 44 58 24 7 24 44 55 5TE6803 L L I2 _ 1 2 1 1 6 N 4 4 7 N I201_12119 7 4 4 5 5TE6800 5TE6810 7 45 74 L 45 74 45 74 Dimensional drawings 44 2 4 4 4 6 4 5TE6804 9 L N 44 7 24 44 58 65 5TE6802 10 74 I201_12117 45 I201_12120 44 5TE9120 Siemens * 10/2015 45 5TE6801 44 55 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets 5TE6 REG socket outlets More information Hinged lid for simple application The hinged lid can be opened at an angle greater than 180 degrees. By pulling on the hinges, the covers stay open, which facilitates plugging in. The hinged lids can be retrofitted on all versions. In order to make sure that it is possible to work on the distribution board in the event of a power failure, we recommend that the infeed socket outlet is fed using a short-circuit current proof cable installation and a separate fuse. The yellow socket outlet must be used for this purpose. Siemens * 10/2015 11 (c) Siemens AG 2015 Transformers, Power Supply Units and Socket Outlets Notes 12 Siemens * 10/2015 (c) Siemens AG 2015 (c) Siemens AG 2015 Siemens AG Energy Management Low Voltage & Products Postfach 10 09 53 93009 REGENSBURG GERMANY www.siemens.com/lowvoltage Subject to change without prior notice PDF (3ZW1012-4AC32-0AC1) PH 0216 12 En Produced in Germany (c) Siemens AG 2016 The information provided in this brochure contains merely general descriptions or characteristics of performance which in case of actual use do not always apply as described or which may change as a result of further development of the products. An obligation to provide the respective characteristics shall only exist if expressly agreed in the terms of contract. Availability and technical specifications are subject to change without notice. All product designations may be trademarks or product names of Siemens AG or supplier companies whose use by third parties for their own purposes could violate the rights of the owners.