6GK1561-4AA01 - SIEMENS - Datasheet.Live

CP 5613 A2/CP 5614 A2

___________________

SIMATIC NET

PG/PC - PROFIBUS

CP 5613 A2/CP 5614 A2

Operating Instructions

08/2016

C79000

-G8976-C301-02

Preface

Description of the device

Software installation

Hardware installation

Configuration

Technical specifications

Certification

Siemens AG

Division Process Industries and Drive

Postfach 48 48

90026 NÜRNBERG

GERMANY

Document order number: C79000-G8976-C301

Ⓟ

09/2016 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 3

Table of contents

1 Preface ................................................................................................................................................... 5

2 Description of the device ......................................................................................................................... 9

2.1 CP 5613 A2 product characteristics ......................................................................................... 9

2.2 CP 5614 A2 product characteristics ....................................................................................... 11

2.3 PROFIBUS interface ............................................................................................................... 12

2.4 Meaning of the LED display .................................................................................................... 13

3 Software installation .............................................................................................................................. 15

3.1 Installing the "SIMATIC NET PC Software" ............................................................................ 15

3.2 Uninstalling the "SIMATIC NET PC Software"........................................................................ 16

4 Hardware installation ............................................................................................................................. 17

4.1 Safety notices ......................................................................................................................... 17

4.2 Installing hardware .................................................................................................................. 18

4.2.1 Automatic adaptation of the bus clock speed ......................................................................... 18

4.2.2 Installing hardware PCI ........................................................................................................... 18

4.3 Hardware compatibility............................................................................................................ 19

4.3.1 Compatibility with other CPs ................................................................................................... 19

4.3.2 Replacement ........................................................................................................................... 19

5 Configuration ........................................................................................................................................ 21

6 Technical specifications ........................................................................................................................ 23

A Certification ........................................................................................................................................... 27

Table of contents

CP 5613 A2/CP 5614 A2

4 Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 5

Preface

What the consignment contains

The following components are supplied with the CP 5613 A2/CP 5614 A2:

● Communications processor CP 5613 A2/CP 5614 A2

● SIMATIC NET CD

● Certificate of license

Please check that the consignment you have received is complete. If the consignment is

incomplete, contact your supplier or your local Siemens office.

Validity of this documentation

These operating instructions are valid for the following products:

● CP 5613 A2

Article number: 6GK1 561-3AA01

● CP 5614 A2

Article number: 6GK1 561-4AA01

Content of this documentation

These operating instructions contain information about the installation and configuration of

the CP 5613 A2 and CP 5614 A2 communications processors.

Updated operating instructions on the Internet

You will find the current version of these operating instructions on the Product Support pages

under the following entry ID: 62612014

(https://support.industry.siemens.com/cs/ww/en/view/62612014)

Further documentation

The documents listed below contain more detailed information on commissioning and using

the communications processor. You will find this documentation on the Product Support

pages on the Internet under the following entry link:

Support (https://support.industry.siemens.com/cs/ww/en/ps)

Preface

CP 5613 A2/CP 5614 A2

6 Operating Instructions, 08/2016, C79000-G8976-C301-02

Enter the entry ID shown below of the relevant manual as the search item.

●

Configuration manual Commissioning PC Stations

This provides you with detailed information on commissioning and configuring SIMATIC

NET PC communications modules.

Entry ID:

109488960 (https://support.industry.siemens.com/cs/ww/en/view/109488960)

●

System manual SIMATIC NET Industrial Communication with PG/PC

–

Volume 1– Basics

Entry ID:

77376110 (https://support.industry.siemens.com/cs/ww/en/view/77376110)

–

Volume 2– Interfaces

Entry ID:

77378184 (https://support.industry.siemens.com/cs/ww/en/view/77378184)

The system manuals introduce the topic of industrial communication and explain the

communications protocols used. There is also a description of the OPC interface as

user programming interface.

●

Installation manual "SIMATIC NET PC Software"

This document contains detailed information on installing the "SIMATIC NET

PC Software".

Entry ID:

77377602 (https://support.industry.siemens.com/cs/ww/en/view/77377602)

●

System manual PROFIBUS Network Manual

In this document you will find detailed information about setting up a PROFIBUS network.

Entry ID:

35222591 (https://support.industry.siemens.com/cs/ww/en/view/35222591)

SIMATIC NET documentation

You will find the entire SIMATIC NET documentation on the pages of Product Support:

15247 (https://support.industry.siemens.com/cs/ww/en/ps/15247)

Go to the required product group and make the following settings:

→ Entry list → Entry type "Manuals / Operating Instructions"

Trademarks

The following and possibly other names not identified by the registered trademark sign ® are

registered trademarks of Siemens AG:

SIMATIC NET, HARDNET, SOFTNET, CP 1612, CP 1613, CP 5612, CP 5613, CP 5614,

CP 5622

Preface

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 7

Industry Online Support

In addition to the product documentation, the comprehensive online information platform of

Siemens Industry Online Support at the following Internet address:

(http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=

en)

Apart from news, there you will also find:

● Project information: Manuals, FAQs, downloads, application examples etc.

● Contacts, Technical Forum

● The option submitting a support query:

(https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid

=38718979&caller=view)

● Our service offer:

Right across our products and systems, we provide numerous services that support you

in every phase of the life of your machine or system - from planning and implementation

to commissioning, through to maintenance and modernization.

You will find contact data on the Internet at the following address:

(http://www.automation.siemens.com/partner/guiwelcome.asp?lang=en)

SITRAIN - Training for Industry

The training offer includes more than 300 courses on basic topics, extended knowledge and

special knowledge as well as advanced training for individual sectors - available at more

than 130 locations. Courses can also be organized individually and held locally at your

location.

You will find detailed information on the training curriculum and how to contact our customer

consultants at the following Internet address:

(www.siemens.com/sitrain)

SIMATIC NET glossary

Explanations of many of the specialist terms used in this documentation can be found in the

SIMATIC NET glossary.

You will find the SIMATIC NET glossary on the Internet at the following address:

50305045 (https://support.industry.siemens.com/cs/ww/en/view/50305045)

Preface

CP 5613 A2/CP 5614 A2

8 Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 9

Description of the device

2.1

CP 5613 A2 product characteristics

CP 5613 A2 characteristics

The CP 5613 A2 is a communications processor for connecting PCs to PROFIBUS. The

essential characteristics are as follows:

● The CP 5613 A2 is equipped with a PROFIBUS interface allowing up to 12 Mbps. It is

intended for operation in PGs and PCs with a PCI bus interface according to the PCI

standard V2.2.

● With the CP 5613 A2, up to 32 devices (PC, PG, SIMATIC S7 or ET 200) can be linked to

form a network segment. By linking several segments with repeaters, a maximum of 124

nodes can be connected.

● Optimized for fast DP master operation (DP Base) with up to 124 DP slaves with full data

consistency

● As an alternative, can also be used as a DP slave

● Relieves the PC due to event mechanisms (automatic detection of data changes)

● Fast logic support regardless of the user program (automatic linking of input and output

data can be set by the user program).

● Plug and play support during installation of the hardware

● Support of all data transmission speeds from 9.6 kbps to 12 Mbps

● Floating RS-485 connector

● Support of PCI 3.3 V/5 V, 33 MHz/66 MHz, 32 bit/64 bit and PCI-X 66 MHz, 32 bit/64 bit

Description of the device

2.1 CP 5613 A2 product characteristics

CP 5613 A2/CP 5614 A2

10 Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2 appearance

The following figure shows the CP 5613 A2 communications processor:

Yellow and green status LED

PROFIBUS interface 1 (master or slave)

Description of the device

2.2 CP 5614 A2 product characteristics

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 11

2.2

CP 5614 A2 product characteristics

CP 5614 A2 characteristics

The CP 5614 A2 is a communications processor for connecting PCs to PROFIBUS. It has

the same characteristics as the CP 5613 A2, as well as:

● Second RS-485 connector for additional connection of the CP as a DP slave to a second

DP network.

● Program-controlled transfer of data between master and slave module to allow for setting

up of hierarchical PROFIBUS networks.

● DP master and DP slave can be operated at the same time.

CP 5614 A2 appearance

The following figure shows the CP 5614 A2 communications processor:

Yellow and green status LED

PROFIBUS interface 1 (master)

PROFIBUS interface 2 (slave)

Description of the device

2.3 PROFIBUS interface

CP 5613 A2/CP 5614 A2

12 Operating Instructions, 08/2016, C79000-G8976-C301-02

2.3

PROFIBUS interface

PROFIBUS network

The physical link between the PROFIBUS interface and the PROFIBUS network is via a

floating RS-485 interface that is part of the module. Depending on the network configuration,

data rates of 9.6 Kbps up to a maximum of 12 Mbps are possible in the PROFIBUS network.

Note

You will find information about the structure of a PROFIBUS network in the system manual

"PROFIBUS Network Manual". The document is part of the Manual Collection. You will also

find this on the Product Support pages under the following ent

ry ID:

35222591 (

https://support.industry.siemens.com/cs/ww/en/view/35222591)

PIN assignment

The D-sub female connector has the following pin assignment:

Short name

Meaning

Input/output

Socket pin 1 is not connected.

2 NC (M24) Socket pin 2 is not connected. With other MPI/DP components,

the return line of the floating 24 V power supply may be via this

pin.

LTG_B

Signal line B of the PROFIBUS connector.

Input/output

4 RTSAS RTSAS, input signal for direct MPI link. The control signal is "1"

active when the automation system connected over a special

MPI cable is sending.

Input

5 M5EXT M5EXT return line (GND) of the 5 V power supply. The current

load of an external consumer connected between P5EXT and

M5EXT must not exceed a maximum of 90 mA.

Output

6 P5EXT P5EXT supply (+5 V) of the 5 V power supply. The current load

of an external consumer connected between P5EXT and

M5EXT must not exceed a maximum of 90 mA (short-circuit

proof).

Output

7 NC (P24V) Socket pin 7 is not connected. With other MPI/DP components,

the P24V supply of the floating 24 V power supply may be via

this pin.

LTG_A

Signal line A of the PROFIBUS connector.

Input/output

Description of the device

2.4 Meaning of the LED display

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 13

Short name

Meaning

Input/output

9 RTS RTS output signal of the CP module. The control signal is "1"

active when the device (PG or PC) is sending.

Output

Shield The shield is connected to components of the connector hous-

ing.

2.4

Meaning of the LED display

LED display

The meaning of the LED display is as follows:

Green and yellow LED

Function

Lit green DP master

Shows the token rotation (in other words, normal operation)

Green off DP master

Incorrect bus parameters, defective bus or CP not in opera-

tion

Green flashes at one second intervals DP master

Bad database

Green and yellow flashing alternately Module is being addressed by diagnostics tool to check

installation

Yellow lit DP slave

Shows polling by the higher-level DP master

(in other

words normal operaton)

Yellow off DP slave

Connector is not addressed

Green flashing fast

Module not started (normal status following reset)

Green and yellow flashing synchronized

Exception status (error in firmware)

Description of the device

2.4 Meaning of the LED display

CP 5613 A2/CP 5614 A2

14 Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 15

Software installation

3.1

Installing the "SIMATIC NET PC Software"

"SIMATIC NET PC Software"

The "SIMATIC NET PC software" is one of several software packages with which you can

operate the communications processor in your PG/PC.

To configure the communications processor, you require additional configuration software.

You will find information on the configuration software in the section "Configuration

(Page 21)".

Condition

The plug and play function is activated in the BIOS of your PG/PC.

Prior to hardware installation

Install the software as described in the installation manual "SIMATIC NET PC Software".

You will find this installation manual on the Product Support pages under the following entry

ID:

77377602 (https://support.industry.siemens.com/cs/ww/en/view/77377602)

You should also note the current information on the "SIMATIC NET PC software" on the

Product Support pages:

Support (https://support.industry.siemens.com/cs/ww/en/ps/15362/pm)

After the hardware installation

After installing the communications processor, your PG/PC automatically searches for a

suitable driver.

1. Follow the instructions of the Hardware Wizard of Windows.

2. Do not activate the search for drivers on the Internet.

Software installation

3.2 Uninstalling the "SIMATIC NET PC Software"

CP 5613 A2/CP 5614 A2

16 Operating Instructions, 08/2016, C79000-G8976-C301-02

3.2

Uninstalling the "SIMATIC NET PC Software"

Condition

The "SIMATIC NET PC Software" is installed on the PG/PC.

Procedure

Note

The recommended procedure removes the entire "SIMATIC NET PC Software" on the

PG/PC, not only the driver for the communications processor.

Uninstall the entire software package as described and recommended in the installation

manual "SIMATIC NET PC Software".

You will find the installation manual on the "SIMATIC NET PC Software" DVD or on the

Product Support pages under the following entry ID:

77377602 (https://support.industry.siemens.com/cs/ww/en/view/77377602)

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 17

Hardware installation

4.1

Safety notices

WARNING

Electric shock possible - work only when the power supply is off

Opening the PG/PC and plugging or pulling the communications processor is permitted

only when the power is off.

Turn off your PG/PC and pull the power cable connector before you start the hardware

installation.

NOTICE

Note the EC directives

Components can be damaged or destroyed by electrostatic discharge. When installing,

keep to the rules for electrostatically sensitive devices (ESD).

• Pick up components and modules only by their edges. Do not touch the pins or

conductors.

• Before opening the PG/PC, make sure that you discharge any electrostatic charge from

your body. You can do this by touching metal parts on the back panel of the PG/PC

pulling the power plug.

• Make sure that you also discharge any electrostatic charge from tools you intend to use

for the work on the PG/PC.

• Do not operate the PG/PC with the housing open.

NOTICE

Firm mounting

The communications processor must sit firmly and uniformly in the slot. Check that the

module sits firmly in the slot as described in the manual accompanying your PG/PC.

Note

Oblique installation position is permitted

Some PG/PC designs require oblique installation of the communications processor. This is

permitted.

Hardware installation

4.2 Installing hardware

CP 5613 A2/CP 5614 A2

18 Operating Instructions, 08/2016, C79000-G8976-C301-02

4.2

Installing hardware

Permitted number of communications processors in the PG/PC

The driver software supports a maximum of 4 communications processor per PG/PC.

4.2.1

Automatic adaptation of the bus clock speed

The communications processor is designed for a bus clock speed of 66 MHz. If the

communications processor is inserted in a PCI slot with a higher bus clock speed, the bus

clock speed is adapted to the highest possible bus rate of the communications processor.

Examples:

● The PCI slot is automatically reduced to a bus clock speed of 66 MHz.

● The bus clock speed of the communications processor is automatically reduced to

33 MHz if a communications processor with a 33 MHz bus clock speed is connected.

4.2.2

Installing hardware PCI

Procedure

Note

•

First install the software

First install the software before you insert the communications processor in the slot.

•

Activated plug and play function

The plug and play function must be activated in the BIOS of your PG/PC.

Follow the steps outlined below when inserting the communications processor:

1. Turn off your PG/PC and pull the power cable connector.

2. Open the PC housing as described in the manual accompanying your PG/PC.

3. Remove the cover of a free PCI slot.

4. Remove the communications processor from its packaging.

5. Insert the communications processor in the PCI slot and secure it.

Make sure that the communications processor is correctly inserted and secured.

6. Close the PC housing as described in the manual accompanying your PG/PC.

Hardware installation

4.3 Hardware compatibility

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 19

7. Insert the power plug into the socket again and turn your PG/PC on.

The plug and play function of Windows automatically searches for a driver.

8. Follow the instructions of the Hardware Wizard of Windows.

Do not

activate the search for drivers on the Internet.

4.3

Hardware compatibility

4.3.1

Compatibility with other CPs

Compatibility with other communications processors

The communications processors CP 5613 A2 and CP 5614 A2 can replace the following

communications processors:

● CP 5613

● CP 5614

4.3.2

Replacement

Note

If the previous CP has been removed from the PG/PC, no configuration changes need to be

made

You can adopt the configuration of the previous CP. To do this, you simply need to reload

the configuration.

Note the following:

When loading the previous configuration, the previous CP has priority

over the new CP. As long as the previous CP is connected, its configuration cannot be

adopted by the new CP. You should therefore remove the previous CP from your PC/PG.

Procedure for replacement

When replacing a module, follow the steps described in the section "Hardware installation

(Page 17)".

Hardware installation

4.3 Hardware compatibility

CP 5613 A2/CP 5614 A2

20 Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 21

Configuration

Configuring

To be able to configure the communications processor, the following engineering or

configuration tools are available:

● STEP 7 V5.5

● STEP 7 Professional (TIA Portal)

● Communication Settings (COML S7)

The steps involved are described in the "Commissioning PC Stations" manual or in the

relevant online helps.

NOTICE

No downloading of a CP 5613 A2 slave configuration to a CP 5614 A2

A DP slave configuration for a CP 5613 A2 must not be downloaded to a CP 5614 A2

because the DP slave will not work with this configuration.

Configuration

CP 5613 A2/CP 5614 A2

22 Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 23

Technical specifications

Technical specifications for CP 5613 A2/CP 5614 A2

Construction

Values

Module format

PC card, short PCI format

Dimensions (H x W x D) in mm

107 x 18 x 168

Weight CP 5613 A2: 105 g

CP 5614 A2: 120 g

Bus interface

PCI V2.2, plug and play

Voltage

Operating voltage

Safety extra low voltage (SELV) to EN 60950

Rated voltage (limit values)

5 VDC (4.75 to 5.25 V)

Current consumption

Current consumption from PCI slot CP 5613 A2: typical: 0.8 A

CP 5614 A2: typical: 0.9 A

Interfaces

Connection to PG/PC

PCI/PCI-X slot , 3.3 V/5 V, 32 bit, 33/66 MHz bus clock

Connector to PROFIBUS 9-pin D-sub female connector with screw locking mecha-

nism

The CP 5614 A2 has two interfaces. If both interfaces of the

CP 5614 A2 are used, straight bus connectors must be

used.

The following network components are recommended for

connection to PROFIBUS:

• RS-485 bus connector,

article number 6GK1500-0EA01

• 12M bus terminal,

article number 6GK1500-0AA10

Type of transmission

RS-485 floating within the SELV limits

Technical specifications

CP 5613 A2/CP 5614 A2

24 Operating Instructions, 08/2016, C79000-G8976-C301-02

Interfaces

Mode of the PROFIBUS interface Floating (interface signals),

non-floating (cable shield)

PROFIBUS controller used • CP 5613 A2 / CP 5614 A2

Master: ASPC2R ST E2a

• CP 5614 A2

Slave: DPC31

Data transfer

Transmission speed

9.6 kbps ... 12 Mbps

Electromagnetic compatibility (EMC)

Emission Class B to EN 55022

FCC class B

Noise immunity on signal lines +/- 2 kV

to EN 61000-4-5, surge

Immunity to discharges of static electricity +/- 6 kV, contact discharge to

IEC 61000-4-2

Immunity to RF interference 10 V/m at

80 MHz to 2 GHz to EN 61000-4-3

10 V/m 50 % ON period at 900 MHz and 1.89 GHz

to EN 61000-4-3

10 V/m with 80 % amplitude modulation

with 1 kHz,

9 kHz - 80 MHz to EN 61000-4-6

Climatic Conditions

Temperature Tested to:

DIN EN 60068-2-1,

DIN EN 60068-2-2,

DIN EN 60068-2-14

Operation

Temperature change maximum 10 K/h

Transportation/storage temperature -40 ℃ to +70 ℃

Temperature change maximum 20 K/h

Relative humidity • tested to DIN IEC 60068-2-78

in operation

85% at 30 ℃ (no condensation)

• tested to DIN IEC 60068-2-30

storage/transportation:

5 % at 25 - 55 °C (no condensation)

Technical specifications

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 25

Mechanical environmental conditions

Vibration during operation tested to DIN EN 60068-2-6

during operation

10 to 58 Hz, amplitude 0.0375 mm;

58 to 500 Hz, acceleration 4.9 m/s²

3 axes

Shock during operation Tested to DIN EN 60068-2-27

during operation

half sine: 50 m/s² (5 g), 30 ms

3 axes

Technical specifications

CP 5613 A2/CP 5614 A2

26 Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 27

Certification

Note

The specified approvals apply only when the corresponding mark is printed on the

communications processor.

Electromagnetic compatibility - EMC directive

The communications processor meets the requirements of the EC Directive:2004/108/EEC

(EMC directive).

The communications processor is designed for use in the following areas:

Area of application

Requirements

Emission

Immunity

Residential areas, business and commercial opera-

tions, and small businesses

EN 61000-6-3 EN 61000-6-1

Industrial environment

EN 61000-6-4

EN 61000-6-2

Declaration of conformity

You will find the declaration of conformity for this communications processor on the Product

Support pages under the following entry ID:

58826997 (https://support.industry.siemens.com/cs/ww/en/view/58826997)

C-TICK approval

The communications processor meets the requirements of the Australian AS/NZS 3548

standard according to EN 61000-6-3.

CSA approval

The communications processor has an approval in accordance with the Canadian CAN/CSA

C22.2 No. 60950-1 standard.

ICES conformity

The communications processor meets the requirements of the Canadian standard ICES-003.

It is rated as a digital device of Class B ("Class B digital apparatus").

Certification

CP 5613 A2/CP 5614 A2

28 Operating Instructions, 08/2016, C79000-G8976-C301-02

FCC approval

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

● Consult the dealer or an experienced radio/TV technician for help.

Siemens AG is not responsible for any radio television interference caused by unauthorized

modifications of this equipment or the substitution or attachment of connecting cables and

equipment other than those specified by Siemens AG. The correction of interference caused

by such unauthorized modification, substitution or attachment will be the responsibility of the

user. The use of shielded I/O cables is required when connecting this equipment to any and

all optional peripheral or host devices. Failure to do so may violate FCC and ICES rules.

UL approval

The communications processor has an approval in accordance with the US standard

UL 60950-1.

Marking for the customs union

EAC (Eurasian Conformity)

Customs union of Russia, Belarus and Kazakhstan

Declaration of the conformity according to the technical regulations of the customs union

(TR CU)