HSMS-8101, 8202, 8207, 8209 Surface Mount Microwave Schottky Mixer Diodes Data Sheet Description/Applications Features These low cost microwave Schottky diodes are specifically designed for use at X/Ku-bands and are ideal for DBS and VSAT downconverter applications. They are available in SOT-23 and SOT-143 standard package configurations. * Optimized for use at 10-14 GHz Note that Avago's manufacturing techniques assure that dice found in pairs and quads are taken from adjacent sites on the wafer, assuring the highest degree of match. * Low Cost Surface Mount Plastic Package Plastic SOT-23 Package Package Lead Code Identification (Top View) * Low Capacitance * Low Conversion Loss * Low RD * Lead-free Option Available SINGLE 3 1 #1 2 RING QUAD 3 4 Plastic SOT-143 Package 1 #7 2 SERIES 3 1 #2 2 CROSS-OVER QUAD 3 4 1 #9 2 Absolute Maximum Ratings [1], TA = +25C Symbol Parameter PT PIV TJ TSTG, Top Total Device Dissipation[2] Peak Inverse Voltage Junction Temperature Storage and Operating Temperature Unit Min. Max. mW V C C -- -- -- -65 75 4 +150 +150 Notes: 1. Operation in excess of any one of these conditions may result in permanent damage to the device. 2. Measured in an infinite heat sink at TCASE = 25C. Derate linearly to zero at 150C per diode. Attention: Observe precautions for handling electrostatic sensitive devices. ESD Machine Model (Class A) ESD Human Body Model (Class 0) Refer to Avago Application Note A004R: Electrostatic Discharge Damage and Control. 2 DC Electrical Specifications, TA = 25C Symbol Parameters and Test Conditions Units HSMS-8101 Min. Max. V CT Total Capacitance VR = 0 V, f = 1 MHz pF 0.26 0.26 0.26 0.26 DC T Capacitance Difference VR = 0 V, f = 1 MHz pF -- 0.04 0.04 0.04 RD Dynamic Resistance IF = 5 mA 14 14 14 14 DRD Dynamic Resistance Difference IF = 5 mA -- 2 2 2 VF Forward Voltage IF = 1 mA mV DVF Forward Voltage Difference IF = 1 mA mV 250 350 4 HSMS-8209 Min. Max. Breakdown Voltage IR = 10 A Package Marking Code where x is date code 4 HSMS-8207 Min. Max. VBR Lead Code 4 HSMS-8202 Min. Max. 250 350 -- 4 250 350 20 250 350 20 20 1 2 7 9 R1x 2Rx R7x R9x RF Electrical Parameters, TA = 25C Symbol Parameter Units Typical Lc Conversion Loss at 12 GHz dB 6.3 Z IF IF Impedance 150 SWR SWR at 12 GHz 1.2 Note: DC Load Resistance = 0 ; LO Power = 1 mW. SPICE Parameters IS = 4.6 E-8 RS = 6 N = 1.09 BV = 7.3 IBV = 10E-5 Linear Equivalent Circuit EG = 0.69 CJO = 0.18 E-12 PB (VJ) = 0.5 M = 0.5 FC = 0.5 TT = 0 0.08 pF 1.0 nH 1.3 nH 6 0.17 pF Rj Self Bias Rj 1 mA 256 2.5 mA 142 3 1 TA = +125C TA = +25C TA = -55C 0.1 0 0.2 0.4 0.6 0.8 IF (Left Scale) 10 10 VF (Right Scale) 1 1 0.3 0.3 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 FORWARD VOLTAGE (V) 9 CONVERSION LOSS (dB) 10 0.01 30 30 IF - FORWARD CURRENT (mA) FORWARD CURRENT (mA) 100 VF - FORWARD VOLTAGE DIFFERENCE (mV) Typical Performance, TC = 25C 7 6 -7 -5 -3 -1 1 3 5 7 9 11 13 LOCAL OSCILLATOR POWER (dBm) V - FORWARD VOLTAGE (V) Figure 1. Typical Forward Current vs. Forward Voltage at Three Temperatures. 8 Figure 3. Typical Conversion Loss vs. Local Oscillator Power. Figure 2. Typical VF Match, HSMS820X Pairs and Quads. Ordering Information Profile Option Descriptions Specify part number followed by option. For example: -BLK = Bulk -TR1 = 3K pc. Tape and Reel, Device Orientation Figures 4, 5 -TR2 = 10K pc. Tape and Reel, Device Orientation Figures 4, 5 Tape and Reeling conforms to Electronic Industries RS-481, "Taping of Surface Mounted Components for Automated Placement." HSMS - 8101 - XXX Bulk or Tape and Reel Option Part Number Surface Mount Schottky Device Orientation REEL For lead-free option, the part number will have the character "G" at the end, eg. -TR2G for a 10K pc lead-free reel. CARRIER TAPE USER FEED DIRECTION COVER TAPE TOP VIEW END VIEW TOP VIEW 4 mm ABC Note: "AB" represents package marking code. "C" represents date code. Figure 4. Option -TR1/-TR2 for SOT-23 Packages. 8 mm ABC ABC ABC ABC ABC ABC ABC 8 mm END VIEW 4 mm Note: "AB" represents package marking code. "C" represents date code. Figure 5. Option -TR1/-TR2 for SOT-143 Packages. 4 Package Characteristics Lead Material ...................................................................................... Alloy 42 Lead Finish ................................... Tin-Lead 85-15% (Non lead-free option) or Tin 100% (Lead-free option) Maximum Soldering Temperature .............................. 260C for 5 seconds Minimum Lead Strength .......................................................... 2 pounds pull Typical Package Inductance .................................................................. 2 nH Typical Package Capacitance .............................. 0.08 pF (opposite leads) Recommended PCB Pad Layout for Avago's SOT-23 Products Package Dimensions Outline 23 (SOT-23) e2 E 0.039 1 0.039 1 e1 E1 XXX 0.079 2.0 e L B 0.035 0.9 C DIMENSIONS (mm) D A A1 Notes: XXX-package marking Drawings are not to scale SYMBOL A A1 B C D E1 e e1 e2 E L MIN. 0.79 0.000 0.37 0.086 2.73 1.15 0.89 1.78 0.45 2.10 0.45 MAX. 1.20 0.100 0.54 0.152 3.13 1.50 1.02 2.04 0.60 2.70 0.69 0.031 0.8 Dimensions in inches mm Outline 143 (SOT-143) Recommended PCB Pad Layout for Avago's SOT-143 Products e2 e1 0.112 2.85 B1 0.079 2 E E1 XXX 0.033 0.85 L B e 0.081 2.05 C 0.048 1.2 0.071 1.8 DIMENSIONS (mm) D A A1 Notes: XXX-package marking Drawings are not to scale SYMBOL A A1 B B1 C D E1 e e1 e2 E L MIN. 0.79 0.013 0.36 0.76 0.086 2.80 1.20 0.89 1.78 0.45 2.10 0.45 MAX. 1.097 0.10 0.54 0.92 0.152 3.06 1.40 1.02 2.04 0.60 2.65 0.69 0.114 2.9 0.033 0.85 0.047 1.2 0.031 0.8 0.033 0.85 e Dimensions in inches mm 5 Tape Dimensions and Product Orientation For Outline SOT-23 P P2 D E P0 F W D1 t1 Ko 9 MAX B0 A0 DESCRIPTION 13.5 MAX 8 MAX SYMBOL SIZE (mm) SIZE (INCHES) CAVITY LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER A0 B0 K0 P D1 3.15 0.10 2.77 0.10 1.22 0.10 4.00 0.10 1.00 + 0.05 0.124 0.004 0.109 0.004 0.048 0.004 0.157 0.004 0.039 0.002 PERFORATION DIAMETER PITCH POSITION D P0 E 1.50 + 0.10 4.00 0.10 1.75 0.10 0.059 + 0.004 0.157 0.004 0.069 0.004 CARRIER TAPE WIDTH THICKNESS W t1 8.00 +0.30 -0.10 0.229 0.013 0.315 +0.012 -0.004 0.009 0.0005 DISTANCE BETWEEN CENTERLINE CAVITY TO PERFORATION (WIDTH DIRECTION) F 3.50 0.05 0.138 0.002 CAVITY TO PERFORATION (LENGTH DIRECTION) P2 2.00 0.05 0.079 0.002 Tape Dimensions and Product Orientation For Outline SOT-143 P D P2 P0 E F W D1 t1 K0 9 MAX 9 MAX A0 B0 DESCRIPTION SYMBOL SIZE (mm) SIZE (INCHES) CAVITY LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER A0 B0 K0 P D1 3.19 0.10 2.80 0.10 1.31 0.10 4.00 0.10 1.00 + 0.25 0.126 0.004 0.110 0.004 0.052 0.004 0.157 0.004 0.039 + 0.010 PERFORATION DIAMETER PITCH POSITION D P0 E 1.50 + 0.10 4.00 0.10 1.75 0.10 0.059 + 0.004 0.157 0.004 0.069 0.004 CARRIER TAPE WIDTH THICKNESS W t1 8.00 +0.30 -0.10 0.254 0.013 0.315+0.012 -0.004 0.0100 0.0005 DISTANCE CAVITY TO PERFORATION (WIDTH DIRECTION) F 3.50 0.05 0.138 0.002 CAVITY TO PERFORATION (LENGTH DIRECTION) P2 2.00 0.05 0.079 0.002 For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries. Data subject to change. Copyright (c) 2006 Avago Technologies Pte. All rights reserved. Obsoletes 5989-2496EN 5989-4024EN September 8, 2006