SEMICONDUCTOR TECHNICAL DATA The MC10H164 is a MECL 10H part which is a functional/pinout duplication of the standard MECL 10K family part, with 100% improvement in propagation delay, and no increase in power supply current. The MC10H164 is designed to be used in data multiplexing and parallel to serial conversion applications. Full parallel gating provides equal delays through any data path. The MC10H164 incorporates an output buffer, eight inputs and an enable. A high on the enable forces the output low. The open emitter output allows the MC10H164 to be connected directly to a data bus. The enable line allows an easy means of expanding to more than 8 lines using additional MC10H164's. * Propagation Delay, 1.0 ns Typical * Power Dissipation, 310 mW Typical (same as MECL 10K) * Improved Noise Margin 150 mV (Over Operating Voltage and Temperature Range) * Voltage Compensated * MECL 10K-Compatible L SUFFIX CERAMIC PACKAGE CASE 620-10 P SUFFIX PLASTIC PACKAGE CASE 648-08 FN SUFFIX PLCC CASE 775-02 LOGIC DIAGRAM A 7 VCC1 = VCC2 = VEE = B 9 C 10 PIN 1 PIN 16 PIN 8 Enable 2 MAXIMUM RATINGS Z 15 X0 6 Characteristic Symbol Rating Unit X1 5 VEE VI -8.0 to 0 Vdc X2 4 Power Supply (VCC = 0) Input Voltage (VCC = 0) 0 to VEE Vdc X3 3 Output Current -- Continuous -- Surge Iout 50 100 mA X4 11 Operating Temperature Range TA Tstg 0 to +75 C -55 to +150 -55 to +165 C C Storage Temperature Range -- Plastic -- Ceramic X5 12 X6 13 X7 14 TRUTH TABLE ELECTRICAL CHARACTERISTICS (VEE = -5.2 V 5%) (See Note) 0 25 Characteristic Symbol Min Max Min Max Min Max Unit IE -- 83 -- 75 -- 83 mA IinH IinL -- 512 -- 320 -- 320 A 0.7 -- 0.7 -- 0.7 Input Current High Input Current Low High Output Voltage Low Output Voltage High Input Voltage Low Input Voltage ENABLE L L L L L L L L H 75 Power Supply Current -- A -0.735 Vdc -1.95 -1.63 -1.95 -1.63 -1.95 -1.60 Vdc -1.17 -0.84 -1.13 -0.81 -1.07 -0.735 Vdc -1.95 -1.48 -1.95 -1.48 -1.95 -1.45 Vdc VOH VOL -1.02 -0.84 -0.98 -0.81 -0.92 VIH VIL Rise Time Fall Time tpd tr tf ns VCC1 ENABLE 1 16 2 15 VCC2 Z X3 3 14 X7 X2 4 13 X6 0.4 0.7 1.0 1.45 2.4 2.8 0.4 0.8 1.1 1.5 2.5 2.9 0.5 0.9 1.2 1.7 2.6 3.2 X1 5 12 X5 0.5 1.5 0.5 1.6 0.5 1.7 ns X0 6 11 X4 0.5 1.5 0.5 1.6 0.5 1.7 ns A 7 10 C VEE 8 9 B NOTE: Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated through a 50-ohm resistor to -2.0 volts. Pin assignment is for Dual-in-Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 6-11 of the Motorola MECL Data Book (DL122/D). 9/96 Motorola, Inc. 1996 Z X0 X1 X2 X3 X4 X5 X6 X7 L DIP PIN ASSIGNMENT AC PARAMETERS Propagation Delay Enable Data Address ADDRESS INPUTS C B A L L L L L H L H L L H H H L L H L H H H L H H H X X X 2-257 REV 6 MC10H164 TYPICAL APPLICATIONS FIGURE 1 -- HIGH SPEED 16-BIT MULTIPLEXER/DEMULTIPLEXER Control Selection 15 14 13 12 11 10 9 8 S0 S1 CR A 7 6 5 4 3 2 1 0 MC10H136 B C D E1 C B A MC10H164 D0 E1 C B A MC10H164 E1 C B A MC10H161 MC10H164 D0 S0 S0 S1 S1 CR A CR MC10H136 B C D E0 MC10H161 MC10H162 E1 C B A Start/Stop 15 14 1312 11 10 9 8 E0 7 6 5 4 3 2 1 0 FIGURE 2 -- 1-OF-64 LINE MULTIPLEXER E A B C MC10H164 E A B C MC10H164 E MSB MC10H161 9 7 LSB Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 E E 2-258 Dout A B C MC10H164 MOTOROLA Dout A B C MC10H164 E Dout A B C MC10H164 E Dout A B C MC10H164 The Bit chosen is dependent on six-bit code present on inputs 7, 9, 14 of the MC10H161 and the A, B, C inputs of the MC10H164. Dout A B C MC10H164 E Dout A B C MC10H164 14 Dout Dout MECL Data DL122 -- Rev 6 MC10H164 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE C 0.007 (0.180) M T L-M B Y BRK -N- U N S 0.007 (0.180) M T L-M S S N S D -L- -M- Z W 20 D 1 V 0.010 (0.250) G1 X S T L-M S N S VIEW D-D A 0.007 (0.180) M T L-M S N S R 0.007 (0.180) M T L-M S N S Z C H -T- SEATING PLANE F VIEW S G1 0.010 (0.250) S T L-M S 0.007 (0.180) M T L-M S N S VIEW S S N S NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). MECL Data DL122 -- Rev 6 N K 0.004 (0.100) J S K1 E G 0.007 (0.180) M T L-M 2-259 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10 _ 0.310 0.330 0.040 --- MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10 _ 7.88 8.38 1.02 --- MOTOROLA MC10H164 OUTLINE DIMENSIONS L SUFFIX CERAMIC DIP PACKAGE CASE 620-10 ISSUE V -A- 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. -B- C L DIM A B C D E F G H K L M N -T- K N SEATING PLANE M E F J G D 16 PL 0.25 (0.010) 16 PL 0.25 (0.010) M T A T B M -A- 9 1 8 B F C L S -T- SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 --- 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0_ 15 _ 0.51 1.01 S P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R 16 S INCHES MIN MAX 0.750 0.785 0.240 0.295 --- 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0_ 15 _ 0.020 0.040 T A M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 MOTOROLA 2-260 *MC10H164/D* MC10H164/D MECL Data DL122 -- Rev 6