CLRC66302HN,151 - NEXPERIA

CLRC663

High performance multi-protocol NFC frontend CLRC663 and

CLRC663 plus

Rev. 5.0 — 27 November 2020 Product data sheet

171150 COMPANY PUBLIC

1 General description

CLRC663, the high performance multi-protocol NFC frontend.

The CLRC663 multi-protocol NFC frontend IC supports the following operating modes

•Read/write mode supporting ISO/IEC 14443 type A and MIFARE Classic

communication mode

•Read/write mode supporting ISO/IEC 14443B

•Read/write mode supporting JIS X 6319-4 (comparable with FeliCa)1

•Passive initiator mode according to ISO/IEC 18092

•Read/write mode supporting ISO/IEC 15693

•Read/write mode supporting ICODE EPC UID/ EPC OTP

•Read/write mode supporting ISO/IEC 18000-3 mode 3/ EPC Class-1 HF

The CLRC663’s internal transmitter is able to drive a reader/writer antenna designed

to communicate with ISO/IEC 14443A and MIFARE Classic IC-based cards and

transponders without additional active circuitry. The digital module manages the complete

ISO/IEC 14443A framing and error detection functionality (parity and CRC).

The CLRC663 supports MIFARE Classic with 1 kB memory, MIFARE Classic with 4 kB

memory, MIFARE Ultralight, MIFARE Ultralight C, MIFARE Plus and MIFARE DESFire

products. The CLRC663 supports higher transfer speeds of the MIFARE product family

up to 848 kbit/s in both directions.

The CLRC663 supports layer 2 and 3 of the ISO/IEC 14443B reader/writer

communication scheme except anticollision. The anticollision needs to be implemented in

the firmware of the host controller as well as in the upper layers.

The CLRC663 is able to demodulate and decode FeliCa coded signals. The FeliCa

receiver part provides the demodulation and decoding circuitry for FeliCa coded signals.

The CLRC663 handles the FeliCa framing and error detection such as CRC. The

CLRC663 supports FeliCa higher transfer speeds of up to 424 kbit/s in both directions.

The CLRC663 is supporting the P2P passive initiator mode in accordance with ISO/IEC

18092.

The CLRC663 supports the vicinity protocol according to ISO/IEC15693, EPC UID and

ISO/IEC 18000-3 mode 3/ EPC Class-1 HF.

The following host interfaces are supported:

•Serial Peripheral Interface (SPI)

•Serial UART (similar to RS232 with voltage levels dependent on pin voltage supply)

•I2C-bus interface (two versions are implemented: I2C and I2CL)

The CLRC663 supports the connection of a secure access module (SAM). A dedicated

separate I2C interface is implemented for a connection of the SAM. The SAM can be

1In the following, the word FeliCa is used for JIS X 6319-4

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

used for high secure key storage and acts as a very performant crypto-coprocessor. A

dedicated SAM is available for connection to the CLRC663.

In this document, the term „MIFARE Classic card“ refers to a MIFARE Classic IC-based

contactless card.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 2 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

2 Features and benefits

•Includes NXP ISO/IEC14443-A and Innovatron ISO/IEC14443-B intellectual property

licensing rights

•High performance multi-protocol NFC frontend for transfer speed up to 848 kbit/s

•Supports ISO/IEC 14443 type A, MIFARE Classic, ISO/IEC 14443 B and FeliCa reader

modes

•P2P passive initiator mode in accordance with ISO/IEC 18092

•Supports ISO/IEC15693, ICODE EPC UID and ISO/IEC 18000-3 mode 3/ EPC Class-1

•Supports MIFARE Classic product encryption by hardware in read/write mode

Allows reading cards based on MIFARE Ultralight, MIFARE Classic with 1 kB memory,

MIFARE Classic with 4 kB memory, MIFARE DESFire EV1, MIFARE DESFire EV2 and

MIFARE Plus ICs

•Low-Power Card Detection

•Compliance to EMV contactless protocol specification on RF level can be achieved

•Supported host interfaces:

–SPI up to 10 Mbit/s

–I2C-bus interfaces up to 400 kBd in Fast mode, up to 1000 kBd in Fast mode plus

–RS232 Serial UART up to 1228.8 kBd, with voltage levels dependent on pin voltage

supply

•Separate I2C-bus interface for connection of a secure access module (SAM)

•FIFO buffer with size of 512 bytes for highest transaction performance

•Flexible and efficient power-saving modes including hard power down, standby and

low-power card detection

•Cost saving by integrated PLL to derive system clock from 27.12 MHz RF quartz crystal

•3.0 V to 5.5 V power supply (CLRC66301, CLRC66302)

2.5 V to 5.5 V power supply (CLRC66303)

•Up to 8 free programmable input/output pins

•Typical operating distance in read/write mode for communication to a ISO/IEC 14443

type A and MIFARE Classic card up to 12 cm, depending on the antenna size and

tuning

•Two package options are available for the CLRC66303:

1. HVQFN32: Package with wettable flanks easing the soldering process and quality

control of soldered parts

2. VFBGA36: Smallest package with optimized pin configuration for simple PCB layout

•The version CLRC66303 offers a more flexible configuration for Low-Power Card

detection compared to the CLRC66301 and CLRC66302 with the new register

LPCD_OPTIONS. In addition, the CLRC66303 offers new additional settings for the

Load Protocol which fit very well to smaller antennas. The CLRC66303 is therefore the

recommended version for new designs.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 3 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

3 Applications

•Industrial

•Access control

•Gaming

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 4 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

4 Quick reference data

Symbol Parameter Conditions Min Typ Max Unit

VDD supply voltage 3.0 5.0 5.5 V

VDD(PVDD) PVDD supply voltage [1] 3.0 5.0 VDD V

VDD(TVDD) TVDD supply voltage 3.0 5.0 5.5 V

Ipd power-down current PDOWN pin pulled HIGH [2] - 8 40 nA

IDD supply current - 17 20 mA

IDD(TVDD) TVDD supply current - 100 250 mA

Tamb operating ambient temperature -25 +25 +85 °C

Tstg storage temperature no supply voltage applied -55 +25 +125 °C

Table 1. Quick reference data CLRC66301 and CLRC66302

[1] VDD(PVDD) must always be the same or lower voltage than VDD.

[2] Ipd is the sum of all supply currents

Symbol Parameter Conditions Min Typ Max Unit

VDD supply voltage 2.5 5.0 5.5 V

VDD(PVDD) PVDD supply voltage [1] 2.5 5.0 VDD V

VDD(TVDD) TVDD supply voltage 2.5 5.0 5.5 V

Ipd power-down current PDOWN pin pulled HIGH [2] - 8 40 nA

IDD supply current - 17 20 mA

recommended operation - 180 350 mAIDD(TVDD) TVDD supply current

absolute limiting value - - 500 mA

Tamb operating ambient temperature device mounted on PCB which

allows sufficient heat dissipation for

the actual power dissipation of the

device

-40 +25 +105 °C

Tstg storage temperature no supply voltage applied -55 +25 +125 °C

Table 2. Quick reference data CLRC66303

[1] VDD(PVDD) must always be the same or lower voltage than VDD.

[2] Ipd is the sum of all supply currents

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 5 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

5 Ordering information

Type number Package

Name Description Version

CLRC66301HN,551 Plastic thermal enhanced very thin quad flat package; no

leads; 32 terminals + 1 central ground; body 5 × 5 × 0.85

mm, MSL2,

Delivered in one tray, MOQ (Minimum order quantity): 490

pcs

CLRC66301HN, 557 Plastic thermal enhanced very thin quad flat package; no

leads; 32 terminals + 1 central ground; body 5 × 5 × 0.85

mm, MSL2,

Delivered in five trays; MOQ: 5x 490 pcs

CLRC66302HN,157 Plastic thermal enhanced very thin quad flat package; no

leads; 32 terminals + 1 central ground; body 5 × 5 × 0.85

mm, MSL1,

Delivered in five trays; MOQ: 5x 490 pcs

CLRC66302HN,118 Plastic thermal enhanced very thin quad flat package; no

leads; 32 terminals + 1 central ground; body 5 × 5 × 0.85

mm, MSL1,

Delivered on reel with 6000 pieces; MOQ: 6000 pcs

CLRC66303HNE Plastic thermal enhanced very thin quad flat package; no

leads; 32 terminals + 1 central ground; body 5 × 5 × 0.85

mm, MSL2, wettable flanks

Delivered in one tray, MOQ (Minimum order quantity): 490

pcs

CLRC66303HNY

HVQFN32

Plastic thermal enhanced very thin quad flat package; no

leads; 32 terminals + 1 central ground; body 5 × 5 × 0.85

mm, MSL2, wettable flanks

Delivered on reel with 6000 pieces; MOQ: 6000 pcs

SOT617-1

CLRC66303A0EV VFBGA36 very thin fine-pitch ball grid array package; 36 terminals,

0.5mm pitch, 3.5mm x 3.5mm x 0.8mm body, MSL3

Delivered on reel with 5000 pieces; MOQ: 5000 pcs

SOT1985-1

Table 3. Ordering information

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 6 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

6 Block diagram

The analog interface handles the modulation and demodulation of the antenna signals for

the contactless interface.

The contactless UART manages the protocol dependency of the contactless interface

settings managed by the host.

The FIFO buffer ensures fast and convenient data transfer between host and the

contactless UART.

The register bank contains the settings for the analog and digital functionality.

001aaj627

HOST

ANTENNA FIFO

BUFFER

ANALOG

INTERFACE

CONTACTLESS

UART SERIAL UART

SPI

I2C-BUS

Figure 1. Simplified block diagram of the CLRC663

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 7 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

7 Pinning information

001aam004

heatsink

Transparent top view

TX1

(1)

DVDD

VDD

TVDD

SIGOUT XTAL1

SIGIN/OUT7 XTAL2

TCK/OUT3 PDOWN

TMS/OUT2 CLKOUT/OUT6

TDI/OUT1 SCL

TDO/OUT0 SDA

AVDD

AUX1

AUX2

RXP

RXN

VMID

TX2

TVSS

8 17

7 18

6 19

5 20

4 21

3 22

2 23

1 24

terminal 1

index area

1. VSS - heat sink connection

Figure 2. Pinning configuration HVQFN32 (SOT617-1)

7.1 Pin description HVQFN32

Pin Symbol Type Description

1 TDO / OUT0 O test data output for boundary scan interface / general purpose output 0

2 TDI / OUT1 I/O test data input boundary scan interface / general purpose output 1

3 TMS / OUT2 I/O test mode select boundary scan interface / general purpose output 2

4 TCK / OUT3 I/O test clock boundary scan interface / general purpose output 3

5 SIGIN /OUT7 I/O Contactless communication interface output. / general purpose output 7

6 SIGOUT O Contactless communication interface input.

7 DVDD PWR digital power supply buffer [1]

8 VDD PWR power supply

9 AVDD PWR analog power supply buffer [1]

10 AUX1 O auxiliary outputs: Pin is used for analog test signal

11 AUX2 O auxiliary outputs: Pin is used for analog test signal

12 RXP I receiver input pin for the received RF signal.

13 RXN I receiver input pin for the received RF signal.

14 VMID PWR internal receiver reference voltage [1]

15 TX2 O transmitter 2: delivers the modulated 13.56 MHz carrier

16 TVSS PWR transmitter ground, supplies the output stage of TX1, TX2

17 TX1 O transmitter 1: delivers the modulated 13.56 MHz carrier

Table 4. Pin description

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 8 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Pin Symbol Type Description

18 TVDD PWR transmitter voltage supply

19 XTAL1 I crystal oscillator input: Input to the inverting amplifier of the oscillator. This pin is

also the input for an externally generated clock (fosc = 27.12 MHz)

20 XTAL2 O crystal oscillator output: output of the inverting amplifier of the oscillator

21 PDOWN I Power Down (RESET)

22 CLKOUT / OUT6 O clock output / general purpose output 6

23 SCL O Serial Clock line

24 SDA I/O Serial Data Line

25 PVDD PWR pad power supply

26 IFSEL0 / OUT4 I host interface selection 0 / general purpose output 4

27 IFSEL1 / OUT5 I host interface selection 1 / general purpose output 5

28 IF0 I/O interface pin, multifunction pin: Can be assigned to host interface RS232, SPI,

I2C, I2C-L

29 IF1 I/O interface pin, multifunction pin: Can be assigned to host interface SPI, I2C, I2C-L

30 IF2 I/O interface pin, multifunction pin: Can be assigned to host interface RS232, SPI,

I2C, I2C-L

31 IF3 I/O interface pin, multifunction pin: Can be assigned to host interface RS232, SPI,

I2C, I2C-L

32 IRQ O interrupt request: output to signal an interrupt event

33 VSS PWR ground and heat sink connection

Table 4. Pin description...continued

[1] This pin is used for connection of a buffer capacitor. Connection of a supply voltage might damage the device.

7.2 Pin description VFBGA36

Symbol Pin Type Description

IF2 A1 I/O interface pin, multifunction pin: Can be assigned to host interface RS232, SPI, I2C,

I2C-L

IF1 A2 I/O interface pin, multifunction pin: Can be assigned to host interface RS232, SPI, I2C,

I2C-L

IF0 A3 I/O interface pin, multifunction pin: Can be assigned to host interface RS232, SPI, I2C,

I2C-L

IFSEL1 A4 I host interface selection 1 / general purpose output 5

PVDD A5 PWR pad power supply

PDOWN A6 I Power Down (RESET)

IRQ B1 O interrupt request: output to signal an interrupt event

TDI / OUT1 B2 I/O test data input boundary scan interface / general purpose output 1

TMS / OUT2 B3 I/O test mode select boundary scan interface / general purpose output 2

TDO / OUT0 B4 O test data output for boundary scan interface / general purpose output 0

SCL B5 I Serial Clock line

Table 5. Pin description VFBGA36

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 9 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Symbol Pin Type Description

XTAL2 B6 O crystal oscillator output: output of the inverting amplifier of the oscillator

IF3 C1 I/O interface pin, multifunction pin: Can be assigned to host interface RS232, SPI, I2C,

I2C-L

TCK / OUT2 C2 I/O test clock boundary scan interface / general purpose output 3

GND C3 PWR ground and heat sink connection

CLKOUT / OUT6 C4 O clock output / general purpose output 6

SDA C5 I/O Serial Data Line

XTAL1 C6 I crystal oscillator input: Input to the inverting amplifier of the oscillator. This pin is

also the input for an externally generated clock (fosc = 27.12 MHz)

DVDD D1 PWR digital power supply buffer [1]

SIGIN /OUT7 D2 I/O Contactless communication interface output. / general purpose output 7

GND D3 PWR ground and heat sink connection

GND D4 PWR ground and heat sink connection

GND D5 PWR ground and heat sink connection

TVDD D6 PWR transmitter voltage supply

VDD E1 PWR power supply

AUX1 E2 O auxiliary output: Pin is used for analog test signal

SIGOUT E3 O Contactless communication interface input.

AUX2 E4 O auxiliary output: Pin is used for analog test signal

IFSEL0 E5 I host interface selection 0 / general purpose output 4

TX1 E6 O transmitter 1: delivers the modulated 13.56 MHz carrier

AVDD F1 PWR analog power supply buffer [1]

RXP F2 I receiver input pin for the received RF signal.

RXN F3 I receiver input pin for the received RF signal.

VMID F4 PWR internal receiver reference voltage [1]

TX2 F5 O transmitter 2: delivers the modulated 13.56 MHz carrier

TVSS F6 PWR transmitter ground, supplies the output stage of TX1, TX2

Table 5. Pin description VFBGA36...continued

[1] This pin is used for connection of a buffer capacitor. Connection of a supply voltage might damage the device.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 10 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8 Functional description

001aam005

I2C,

LOGICAL

FIFO

512 Bytes

REGISTERS

STATEMACHINES

EEPROM

8 kByte

SPI

SAM interface

VOLTAGE

REGULATOR

3/5 V =>

1.8 V

DVDD

POR

ADC PLLLFO

RX OSCTX

VOLTAGE

REGULATOR

3/5 V =>

1.8 V

AVDD

RNG

ANALOGUE FRONT-END

BOUNDARY

SCAN

IF0

IFSEL0

IFSEL1

IF1

IF2

IF3

TCK

TDI

TMS

TDO

RESET

LOGIC PDOWN

I2C

UART

SPI

host interfaces

INTERRUPT

CONTROLLER

IRQ SIGIN

TIMER0..3

CRC

TIMER4

(WAKE-UP

TIMER)

SIGPRO

CODEC

DECOD

CL-

COPRO

SIGIN/

SIGOUT

CONTROL

SIGOUT VMID RXN

RXP

TX1

TX2

XTAL1

XTAL2

SDA

SCL

VDD

VSS

PVDD

TVDD

TVSS

AUX1

AUX2

AVDD

DVDD

CLKOUT

Figure 3. Detailed block diagram of the CLRC663

8.1 Interrupt controller

The interrupt controller handles the enabling/disabling of interrupt requests. All of the

interrupts can be configured by firmware. Additionally, the firmware has possibilities to

trigger interrupts or clear pending interrupt requests. Two 8-bit interrupt registers IRQ0

and IRQ1 are implemented, accompanied by two 8-bit interrupt enable registers IRQ0En

and IRQ1En. A dedicated functionality of bit 7 to set and clear bits 0 to 6 in this interrupt

controller register is implemented.

The CLRC663 indicates certain events by setting bit IRQ in the register Status1Reg and

additionally, if activated, by pin IRQ. The signal on pin IRQ may be used to interrupt the

host using its interrupt handling capabilities. This allows the implementation of efficient

host software.

Table 4. shows the available interrupt bits, the corresponding source and the condition

for its activation. The interrupt bits Timer0IRQ, Timer1IRQ, Timer2IRQ, Timer3OIRQ, in

underflows.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 11 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

The TxIRQ bit in register IRQ0 indicates that the transmission is finished. If the state

changes from sending data to transmitting the end of the frame pattern, the transmitter

unit sets the interrupt bit automatically.

The bit RxIRQ in register IRQ0 indicates an interrupt when the end of the received data is

detected.

The bit IdleIRQ in register IRQ0 is set if a command finishes and the content of the

command register changes to idle.

The register WaterLevel defines both - minimum and maximum warning levels - counting

from top and from bottom of the FIFO by a single value.

The bit HiAlertIRQ in register IRQ0 is set to logic 1 if the HiAlert bit is set to logic 1, that

means the FIFO data number has reached the top level as configured by the register

WaterLevel and bit WaterLevelExtBit.

The bit LoAlertIRQ in register IRQ0 is set to logic 1 if the LoAlert bit is set to logic 1, that

means the FIFO data number has reached the bottom level as configured by the register

WaterLevel.

The bit ErrIRQ in register IRQ0 indicates an error detected by the contactless UART

during receive. This is indicated by any bit set to logic 1 in register Error.

The bit LPCDIRQ in register IRQ0 indicates a card detected.

The bit RxSOFIRQ in register IRQ0 indicates a detection of a SOF or a subcarrier by the

contactless UART during receiving.

The bit GlobalIRQ in register IRQ1 indicates an interrupt occurring at any other interrupt

source when enabled.

Interrupt bit Interrupt source Is set automatically, when

Timer0IRQ Timer Unit the timer register T0 CounterVal underflows

Timer1IRQ Timer Unit the timer register T1 CounterVal underflows

Timer2IRQ Timer Unit the timer register T2 CounterVal underflows

Timer3IRQ Timer Unit the timer register T3 CounterVal underflows

TxIRQ Transmitter a transmitted data stream ends

RxIRQ Receiver a received data stream ends

IdleIRQ Command Register a command execution finishes

HiAlertIRQ FIFO-buffer pointer the FIFO data number has reached the top level as

configured by the register WaterLevel

LoAlertIRQ FIFO-buffer pointer the FIFO data number has reached the bottom level as

configured by the register WaterLevel

ErrIRQ contactless UART a communication error had been detected

LPCDIRQ LPCD a card was detected when in low-power card detection

mode

RxSOFIRQ Receiver detection of a SOF or a subcarrier

GlobalIRQ all interrupt sources will be set if another interrupt request source is set

Table 6. Interrupt sources

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 12 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.2 Timer module

Timer module overview

The CLRC663 implements five timers. Four timers -Timer0 to Timer3 - have an input

clock that can be configured by register T(x)Control to be 13.56 MHz, 212 kHz, (derived

from the 27.12 MHz quartz) or to be the underflow event of the fifth Timer (Timer4). Each

timer implements a counter register which is 16 bit wide. A reload value for the counter

is defined in a range of 0000h to FFFFh in the registers TxReloadHi and TxReloadLo.

The fifth timer Timer4 is intended to be used as a wake-up timer and is connected to the

internal LFO (Low Frequency Oscillator) as input clock source.

The TControl register allows the global start and stop of each of the four timers Timer0

to Timer3. Additionally, this register indicates if one of the timers is running or stopped.

Each of the five timers implements an individual configuration register set defining timer

reload value (e.g. T0ReloadHi, T0ReloadLo), the timer value (e.g. T0CounterValHi,

T0CounterValLo) and the conditions which define start, stop and clockfrequency (e.g.

T0Control).

The external host may use these timers to manage timing relevant tasks. The timer unit

may be used in one of the following configurations:

•Time-out counter

•Watch-dog counter

•Stop watch

•Programmable one-shot timer

•Periodical trigger

The timer unit can be used to measure the time interval between two events or to

indicate that a specific event has occurred after an elapsed time. The timer register

content is modified by the timer unit, which can be used to generate an interrupt to allow

a host to react on this event.

The counter value of the timer is available in the registers T(x)CounterValHi,

T(x)CounterValLo. The content of these registers is decremented at each timer clock.

If the counter value has reached a value of 0000h and the interrupts are enabled for this

specific timer, an interrupt will be generated as soon as the next clock is received.

If enabled, the timer event can be indicated on the pin IRQ (interrupt request). The bit

Timer(x)IRQ can be set and reset by the host controller. Depending on the configuration,

the timer will stop counting at 0000h or restart with the value loaded from registers

T(x)ReloadHi, T(x)ReloadLo.

The counting of the timer is indicated by bit TControl.T(x)Running.

The timer can be started by setting bits TControl.T(x)Running and

TControl.T(x)StartStopNow or stopped by setting the bits TControl.T(x)StartStopNow and

clearing TControl.T(x)Running.

Another possibility to start the timer is to set the bit T(x)Mode.T(x)Start. This can be

useful if dedicated protocol requirements need to be fulfilled.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 13 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.2.1 Timer modes

8.2.1.1 Time-Out- and Watch-Dog-Counter

Having configured the timer by setting register T(x)ReloadValue and starting the counting

of Timer(x) by setting bit TControl.T(x)StartStop and TControl.T(x)Running, the timer unit

decrements the T(x)CounterValue Register beginning with the configured start event. If

the configured stop event occurs before the Timer(x) underflows (e.g. a bit is received

from the card), the timer unit stops (no interrupt is generated).

If no stop event occurs, the timer unit continues to decrement the counter registers until

the content is zero and generates a timer interrupt request at the next clock cycle. This

allows indicating to a host that the event did not occur during the configured time interval.

8.2.1.2 Wake-up timer

The wake-up Timer4 allows to wake-up the system from standby after a predefined time.

The system can be configured in such a way that it is entering the standby mode again in

case no card had been detected.

This functionality can be used to implement a low-power card detection (LPCD). For

the low-power card detection, it is recommended to set T4Control.T4AutoWakeUp

and T4Control.T4AutoRestart, to activate the Timer4 and automatically set the system

in standby. The internal low frequency oscillator (LFO) is then used as input clock

for this Timer4. If a card is detected, the host-communication can be started. If bit

T4Control.T4AutoWakeUp is not set, the CLRC663 will not enter the standby mode again

in case no card is detected but stays fully powered.

8.2.1.3 Stop watch

The elapsed time between a configured start- and stop event may be measured by the

CLRC663 timer unit. By setting the registers T(x)ReloadValueHi, T(x)ReloadValueLo the

timer starts to decrement as soon as activated. If the configured stop event occurs, the

timer stops decrementing. The elapsed time between start and stop event can then be

calculated by the host dependent on the timer interval TTimer:

(1)

If an underflow occurred which can be identified by evaluating the corresponding IRQ bit,

the performed time measurement according to the formula above is not correct.

8.2.1.4 Programmable one-shot timer

The host configures the interrupt and the timer, starts the timer and waits for the interrupt

event on pin IRQ. After the configured time, the interrupt request will be raised.

8.2.1.5 Periodical trigger

If the bit T(x)Control.T(x)AutoRestart is set and the interrupt is activated, an interrupt

request will be indicated periodically after every elapsed timer period.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 14 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.3 Contactless interface unit

The contactless interface unit of the CLRC663 supports the following read/write operating

modes:

•ISO/IEC14443 type A and MIFARE Classic

•ISO/IEC14443B

•FeliCa

•ISO/IEC15693/ICODE

•ICODE EPC UID

•ISO/IEC 18000-3 mode 3/ EPC Class-1 HF

001aal996

BATTERY/POWER SUPPLY

reader/writer

MICROCONTROLLER

READER IC ISO/IEC 14443 A CARD

Figure 4. Read/write mode

A typical system using the CLRC663 is using a microcontroller to implement the higher

levels of the contactless communication protocol and a power supply (battery or external

supply).

8.3.1 Communication mode for ISO/IEC 14443 type A and for MIFARE Classic

The physical level of the communication is shown in the following figure:

(1)

(2)

001aam268

ISO/IEC 14443 A CARD

ISO/IEC 14443 A

READER

1. Reader to Card 100 % ASK, Miller Coded, Transfer speed 106 kbit/s to 848 kbit/s

2. Card to Reader, Subcarrier Load Modulation Manchester Coded or BPSK, transfer speed 106

kbit/s to 848 kbit/s

Figure 5. Read/write mode for ISO/IEC 14443 type A and read/write mode for MIFARE

Classic

The physical parameters are described in the following table:

Transfer speedCommunication

direction

Signal type

106 kbit/s 212 kbit/s 424 kbit/s 848 kbit/s

reader side

modulation

100 % ASK 100% ASK 100% ASK 100% ASK

bit encoding modified Miller

encoding

modified Miller

encoding

modified Miller

encoding

modified Miller

encoding

Reader to card (send

data from the CLRC663

to a card)

fc = 13.56 MHz

bit rate [kbit/s] fc / 128 fc / 64 fc / 32 fc / 16

Table 7. Communication overview for ISO/IEC 14443 type A and read/write mode for MIFARE Classic

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 15 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Transfer speedCommunication

direction

Signal type

106 kbit/s 212 kbit/s 424 kbit/s 848 kbit/s

card side

modulation

subcarrier load

modulation

subcarrier load

modulation

subcarrier load

modulation

subcarrier load

modulation

subcarrier

frequency

fc / 16 fc / 16 fc / 16 fc / 16

Card to reader

(CLRC663 receives

data from a card)

bit encoding Manchester

encoding

BPSK BPSK BPSK

Table 7. Communication overview for ISO/IEC 14443 type A and read/write mode for MIFARE Classic...continued

The CLRC663 connection to a host is required to manage the complete ISO/IEC 14443

type A and MIFARE Classic communication protocol. The following figure shows the data

coding and framing according to ISO/IEC 14443 type A and MIFARE Classic.

001aak585

ISO/IEC 14443 A framing at 106 kBd

8-bit data 8-bit data 8-bit data

odd

parity

odd

parity

start

odd

parity

start bit is 1

ISO/IEC 14443 A framing at 212 kBd, 424 kBd and 848 kBd

8-bit data 8-bit data 8-bit data

odd

parity

odd

parity

start

even

parity

start bit is 0

burst of 32

subcarrier clocks

even parity at the

end of the frame

Figure 6. Data coding and framing according to ISO/IEC 14443 A

The internal CRC coprocessor calculates the CRC value based on ISO/IEC 14443 A part

3 and handles parity generation internally according to the transfer speed.

8.3.2 ISO/IEC14443 type B functionality

The physical level of the communication is shown in the following figure:

(1)

(2)

001aal997

ISO/IEC 14443 B CARD

ISO/IEC 14443 B

READER

1. Reader to Card NRZ, Miller coded, transfer speed 106 kbit/s to 848 kbit/s

2. Card to reader, Subcarrier Load Modulation Manchester Coded or BPSK, transfer speed 106

kbit/s to 848 kbit/s

Figure 7. ISO/IEC 14443 type B communication diagram

The physical parameters are described in the following table:

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 16 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Transfer speedCommunication

direction

Signal type

106 kbit/s 212 kbit/s 424 kbit/s 848 kbit/s

reader side

modulation

10 % ASK 10 % ASK 10 % ASK 10 % ASK

bit encoding NRZ NRZ NRZ NRZ

Reader to card (send

data from the CLRC663

to a card)

fc = 13.56 MHz

bit rate [kbit/s] 128 / fc 64 / fc 32 / fc 16 / fc

card side

modulation

subcarrier load

modulation

subcarrier load

modulation

subcarrier load

modulation

subcarrier load

modulation

subcarrier

frequency

fc / 16 fc / 16 fc / 16 fc / 16

Card to reader

(CLRC663 receives

data from a card)

bit encoding BPSK BPSK BPSK BPSK

Table 8. Communication overview for ISO/IEC 14443 B reader/writer

The CLRC663 connected to a host is required to manage the complete ISO/IEC 14443 B

protocol. The following figure shows the ISO/IEC 14443B SOF and EOF.

001aam270

UNMODULATED (SUB)

CARRIER

Start of Frame (SOF)

sequence

9.44 µs

''0'' ''0'' ''0'' ''0'' ''0'' ''0'' ''0'' ''0'' ''0'' ''0'' ''1'' ''1'' DATA

LAST CHARACTER UNMODULATED (SUB)

CARRIER

End of Frame (EOF)

sequence

9.44 µs

''0'' ''0'' ''0'' ''0'' ''0'' ''0'' ''0'' ''0'' ''0'' ''0''

Figure 8. SOF and EOF according to ISO/IEC 14443 B

8.3.3 FeliCa functionality

The FeliCa mode is the general reader/writer to card communication scheme according

to the FeliCa specification. The communication on a physical level is shown in the

following figure:

001aam271

FeliCa READER

(PCD)

FeliCa CARD

(PICC)

1. PCD to PICC 8-30 % ASK

Manchester Coded,

baudrate 212 to 424 kbaud

2. PICC to PCD, > Load modulation

Manchester Coded,

baudrate 212 to 424 kbaud

Figure 9. FeliCa read/write communication diagram

The physical parameters are described in the following table:

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 17 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Transfer speed FeliCa FeliCa higher transfer

speeds

Communication

direction

Signal type

212 kbit/s 424 kbit/s

reader side

modulation

8 % to 30 % ASK 8 % to 30 % ASK

bit encoding Manchester encoding Manchester encoding

Reader to card (send

data from the CLRC663

to a card)

fc = 13.56 MHz

bit rate fc/64 fc/32

card side load

modulation

Load modulation Load modulationCard to reader (CLRC663

receives data from a

card) bit encoding Manchester encoding Manchester encoding

Table 9. Communication overview for FeliCa reader/writer

The CLRC663 needs to be connected to a dedicated host to be able to support the

complete FeliCa protocol.

8.3.3.1 FeliCa framing and coding

Preamble (Hex.) Sync

(Hex.)

Len n-Data CRC

00 00 00 00 00 00 B2 4D

Table 10. FeliCa framing and coding

To enable the FeliCa communication a 6 byte preamble (00h, 00h, 00h, 00h, 00h, 00h)

and 2 bytes sync bytes (B2h, 4Dh) are sent to synchronize the receiver.

The following Len byte indicates the length of the sent data bytes plus the LEN byte itself.

The CRC calculation is done according to the FeliCa definitions with the MSB first.

To transmit data on the RF interface, the host controller has to send the Len- and data-

bytes to the CLRC663's FIFO-buffer. The preamble and the sync bytes are generated by

the CLRC663 automatically and must not be written to the FIFO by the host controller.

The CLRC663 performs internally the CRC calculation and adds the result to the data

frame.

8.3.4 ISO/IEC15693 functionality

The physical parameters are described in the following table:

Transfer speedCommunication

direction

Signal type

fc / 8192 kbit/s fc / 512 kbit/s

reader side

modulation

10 % to 30 % ASK or

100 % ASK

10 % to 30 % ASK 90 %

to 100 % ASK

bit encoding 1/256 1/4

Reader to label

(send data from the

CLRC663 to a card)

data rate 1.66 kbit/s 26.48 kbit/s

Table 11. Communication overview for ISO/IEC 15693 reader/writer reader to label

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 18 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Transfer speedCommunication

direction

Signal type

6.62 (6.67) kbit/s 13.24 kbit/s[1] 26.48

(26.69) kbit/s

52.96 kbit/s

card side

modulation

not supported not supported single (dual)

subcarrier

load

modulation

ASK

single

subcarrier

load

modulation

ASK

bit length

(μs)

- - 37.76 (37.46) 18.88

Label to reader

(CLRC663

receives data

from a card)

fc = 13.56 MHz

bit encoding - - Manchester

coding

Manchester

coding

subcarrier

frequency

[MHz]

- - fc / 32 (fc /

28)

fc / 32

Table 12. Communication overview for ISO/IEC 15693 reader/writer label to reader

[1] Fast inventory (page) read command only (ICODE proprietary command).

001aam272

pulse

modulated

carrier

~9.44 µs

0 1 2 3 4

~18.88 µs

. 2 . . . ..... . . . . . . . . . 22..... 2 2

2 55 5 5

5~4,833 ms 32 4 5

Figure 10. Data coding according to ISO/IEC 15693. standard mode reader to label

8.3.5 EPC-UID/UID-OTP functionality

The physical parameters are described in the following table:

Transfer speedCommunication

direction

Signal type

26.48 kbit/s 52.96 kbit/s

reader side modulation 10 % to 30 % ASK

bit encoding RTZ

Reader to card

(send data from the

CLRC663 to a card)

bit length 37.76 μs

card side modulation single subcarrier load

modulation

bit length 18.88 μs

Card to reader

(CLRC663 receives

data from a card)

bit encoding Manchester coding

Table 13. Communication overview for EPC/UID

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 19 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Data coding and framing according to EPC global 13.56 MHz ISM (industrial, scientific

and medical) Band Class 1 Radio Frequency Identification Tag Interface Specification

(Candidate Recommendation, Version 1.0.0).

8.3.6 ISO/IEC 18000-3 mode 3/ EPC Class-1 HF functionality

The ISO/IEC 18000-3 mode 3/ EPC Class-1 HF is not described in this document. For a

detailed explanation of the protocol, refer to the ISO/IEC 18000-3 mode 3/ EPC Class-1

HF standard.

8.3.6.1 Data encoding ICODE

The ICODE protocols have mainly three different methods of data encoding:

•"1" out of "4" coding scheme

•"1" out of "256" coding scheme

•"Return to Zero" (RZ) coding scheme

Data encoding for all three coding schemes is done by the ICODE generator.

The supported EPC Class-1 HF modes are:

•2 pulse for 424 kbit subcarrier

•4 pulse for 424 kbit subcarrier

•2 pulse for 848 kbit subcarrier

•4 pulse for 848 kbit subcarrier

8.3.7 ISO/IEC 18092 mode

The CLRC663 supports Passive Initiator Communication mode at the transfer speeds

106 kbit/s, 212 kbit/s and 424 kbit/s as defined in the ISO/IEC 18092 standard.

•Passive communication mode means that the target answers to an initiator command

in a load modulation scheme. The initiator is active in terms of generating the RF field.

•Initiator: generates RF field at 13.56 MHz and starts the ISO/IEC 18092

communication.

•Target: responds to initiator command either in a load modulation scheme in Passive

communication mode or using a self-generated and self-modulated RF field for Active

Communication mode.

8.3.7.1 Passive communication mode

Passive communication mode means that the target answers to an initiator command in

a load modulation scheme. The initiator is active meaning generating the RF field.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 20 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

host NFC INITIATOR

powered to

generate RF field

1. initiator starts communication

at selected transfer speed

2. targets answers using

load modulated data

at the same transfer speed

host

NFC TARGET

powered for

digital processing

001aan217

Figure 11. Passive communication mode

Communication

direction

106 kbit/s 212 kbit/s 424 kbit/s

Initiator → target According to ISO/IEC

14443A

100 % ASK, Modified Miller

Coded

According to FeliCa, 8 % to 30 % ASK

Manchester Coded

Target → initiator According to ISO/IEC

14443A subcarrier load

modulation, Manchester

Coded

According to FeliCa, > 12 % ASK

Manchester Coded

Table 14. Communication overview for Passive communication mode

The contactless UART of CLRC663 and a dedicated host controller are required to

handle the ISO/IEC 18092 passive initiator protocol.

8.3.7.2 ISO/IEC 18092 framing and coding

The ISO/IEC 18092 framing and coding in Passive communication mode is defined in the

ISO/IEC 18092 standard.

Transfer speed Framing and Coding

106 kbit/s According to the ISO/IEC 14443 type A and MIFARE

scheme

212 kbit/s According to the FeliCa scheme

424 kbit/s According to the FeliCa scheme

Table 15. Framing and coding overview

8.3.7.3 ISO/IEC 18092 protocol support

The ISO/IEC 18092 protocol is not described in this document. For a detailed explanation

of the protocol, refer to the ISO/IEC 18092 standard.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 21 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.4 Host interfaces

8.4.1 Host interface configuration

The CLRC663 supports direct interfacing of various hosts as the SPI, I2C, I2CL and

serial UART interface type. The CLRC663 resets its interface and checks the current

host interface type automatically having performed a power-up or resuming from power

down. The CLRC663 identifies the host interface by the means of the logic levels on

the control pins after the Cold Reset Phase. This is done by a combination of fixed

pin connections.The following table shows the possible configurations defined by

IFSEL1,IFSEL0:

Pin Pin Symbol UART SPI I2C I2C-L

28 IF0 RX MOSI ADR1 ADR1

29 IF1 n.c. SCK SCL SCL

30 IF2 TX MISO ADR2 SDA

31 IF3 PAD_VDD NSS SDA ADR2

26 IFSEL0 VSS VSS PAD_VDD PAD_VDD

27 IFSEL1 VSS PAD_VDD VSS PAD_VDD

Table 16. Connection scheme for detecting the different interface types

8.4.2 SPI interface

8.4.2.1 General

001aal998

READER IC

IF1

SCK

IF0

MOSI

IF2

MISO

IF3

NSS

Figure 12. Connection to host with SPI

The CLRC663 acts as a slave during the SPI communication. The SPI clock SCK has to

be generated by the master. Data communication from the master to the slave uses the

Line MOSI. Line MISO is used to send data back from the CLRC663 to the master.

A serial peripheral interface (SPI compatible) is supported to enable high-speed

communication to a host. The implemented SPI compatible interface is according to a

standard SPI interface. The SPI compatible interface can handle data speed of up to

10 Mbit/s. In the communication with a host, CLRC663 acts as a slave receiving data

from the external host for register settings and to send and receive data relevant for the

communication on the RF interface.

NSS (Not Slave Select) enables or disables the SPI interface. When NSS is logical high,

the interface is disabled and reset. Between every SPI command, the NSS must go to

logical high to be able to start the next command read or write.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 22 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

On both data lines (MOSI, MISO) each data byte is sent by MSB first. Data on MOSI

line shall be stable on rising edge of the clock line (SCK) and is allowed to change on

falling edge. The same is valid for the MISO line. Data is provided by the CLRC663 on

the falling edge and is stable on the rising edge.The polarity of the clock is low at SPI

idle.

8.4.2.2 Read data

To read out data from the CLRC663 by using the SPI compatible interface, the following

byte order has to be used.

The first byte that is sent defines the mode (LSB bit) and the address.

byte 0 byte 1 byte 2 byte 3 to n-1 byte n byte n+1

MOSI address 0 address 1 address 2 …….. address n 00h

MISO X data 0 data 1 …….. data n - 1 data n

Table 17. Byte Order for MOSI and MISO

Remark: The Most Significant Bit (MSB) has to be sent first.

8.4.2.3 Write data

To write data to the CLRC663 using the SPI interface, the following byte order has to

be used. It is possible to write more than one byte by sending a single address byte

(see.8.5.2.4).

The first send byte defines both, the mode itself and the address byte.

byte 0 byte 1 byte 2 3 to n-1 byte n byte n + 1

MOSI address 0 data 0 data 1 …….. data n - 1 data n

MISO X X X …….. X X

Table 18. Byte Order for MOSI and MISO

Remark: The Most Significant Bit (MSB) has to be sent first.

8.4.2.4 Address byte

The address byte has to fulfill the following format:

The LSB bit of the first byte defines the used mode. To read data from the CLRC663, the

LSB bit is set to logic 1. To write data to the CLRC663, the LSB bit has to be cleared. The

bits 6 to 0 define the address byte.

NOTE: When writing the sequence [address byte][data0][data1][data2]..., [data0] is

written to address [address byte], [data1] is written to address [address byte + 1] and

[data2] is written to [address byte + 2].

Exception: This auto increment of the address byte is not performed if data is written to

the FIFO address

76543210

address 6 address 5 address 4 address 3 address 2 address 1 address 0 1 (read)

0 (write)

Table 19. Address byte 0 register; address MOSI

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 23 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

76543210

MSB LSB

Table 19. Address byte 0 register; address MOSI...continued

8.4.2.5 Timing Specification SPI

The timing condition for SPI interface is as follows:

Symbol Parameter Min Typ Max Unit

tSCKL SCK LOW time 50 - - ns

tSCKH SCK HIGH time 50 - - ns

th(SCKH-D) SCK HIGH to data input hold time 25 - - ns

tsu(D-SCKH) data input to SCK HIGH set-up time 25 - - ns

th(SCKL-Q) SCK LOW to data output hold time - - 25 ns

t(SCKL-NSSH) SCK LOW to NSS HIGH time 0 - - ns

tNSSH NSS HIGH time 50 - - ns

Table 20. Timing conditions SPI

aaa-016093

tSCKL

tNSSH tSCKH tSCKL

tsu(D-SCKH) th(SCKH-D)

th(SCKL-Q)

t(SCKL-NSSH)

SCK

MOSI

MISO

MSB

LSB

NSS

Figure 13. Connection to host with SPI

Remark: To send more bytes in one data stream, the NSS signal must be LOW during

the send process. To send more than one data stream, the NSS signal must be HIGH

between each data stream.

8.4.3 RS232 interface

8.4.3.1 Selection of the transfer speeds

The internal UART interface is compatible to an RS232 serial interface. The levels

supplied to the pins are between VSS and PVDD. To achieve full compatibility of the

voltage levels to the RS232 specification, an RS232 level shifter is required.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 24 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Table 22 describes examples for different transfer speeds and relevant register settings.

The resulting transfer speed error is less than 1.5 % for all described transfer speeds.

The default transfer speed is 115.2 kbit/s.

To change the transfer speed, the host controller has to write a value for the new transfer

speed to the register SerialSpeedReg. The bits BR_T0 and BR_T1 define factors to set

the transfer speed in the SerialSpeedReg.

Table 21 describes the settings of BR_T0 and BR_T1.

BR_T0 01234567

factor BR_T0 1 1 2 4 8 16 32 64

range BR_T1 1 to 32 33 to 64 33 to 64 33 to 64 33 to 64 33 to 64 33 to 64 33 to 64

Table 21. Settings of BR_T0 and BR_T1

Serial SpeedRegTransfer speed (kbit/s)

(Hex.)

Transfer speed accuracy (%)

7.2 FA -0.25

9.6 EB 0.32

14.4 DA -0.25

19.2 CB 0.32

38.4 AB 0.32

57.6 9A -0.25

115.2 7A -0.25

128 74 -0.06

230.4 5A -0.25

460.8 3A -0.25

921.6 1C 1.45

1228.8 15 0.32

Table 22. Selectable transfer speeds

The selectable transfer speeds as shown are calculated according to the following

formulas:

if BR_T0 = 0: transfer speed = 27.12 MHz / (BR_T1 + 1)

if BR_T0 > 0: transfer speed = 27.12 MHz / (BR_T1 + 33)/2(BR_T0 - 1)

Remark: Transfer speeds above 1228.8 kBits/s are not supported.

8.4.3.2 Framing

Bit Length Value

Start bit (Sa) 1 bit 0

Data bits 8 bit Data

Stop bit (So) 1 bit 1

Table 23. UART framing

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 25 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Remark: For data and address bytes, the LSB bit has to be sent first. No parity bit is

used during transmission.

Read data: To read out data using the UART interface, the flow described below has to

be used. The first send byte defines both the mode itself and the address. The Trigger on

pin IF3 has to be set, otherwise no read of data is possible.

Mode byte 0 byte 1

RX address -

TX - data 0

Table 24. Byte Order to Read Data

001aam298

A0 A1Sa A2 A3

RX A4 A5 A6 RD/

NWR

DATA

ADDRESS

D1Sa D2 D3 D4 D5 D6 D7 So

Figure 14. Example for UART Read

Write data:

To write data to the CLRC663 using the UART interface, the following sequence has to

be used.

The first send byte defines both, the mode itself and the address.

Mode byte 0 byte 1

RX address 0 data 0

TX address 0

Table 25. Byte Order to Write Data

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 26 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

001aam299

A0 A1Sa A2 A3

RX A4 A5 A6 RD/

NWR

ADDRESS

A1Sa A2 A3 A4 A5 A6 RD/

NWR

DATA

D1Sa D2 D3 D4 D5 D6 D7 So

Figure 15. Example diagram for a UART write

Remark: Data can be sent before address is received.

8.4.4 I2C-bus interface

8.4.4.1 General

An Inter IC (I2C) bus interface is supported to enable a low cost, low pin count serial bus

interface to the host. The implemented I2C interface is mainly implemented according to

the NXP Semiconductors I2C interface specification, rev. 3.0, June 2007. The CLRC663

can act as a slave receiver or slave transmitter in standard mode, fast mode and fast

mode plus.

The following features defined by the NXP Semiconductors I2C interface specification,

rev. 3.0, June 2007 are not supported:

•The CLRC663 I2C interface does not stretch the clock

•The CLRC663 I2C interface does not support the general call. This means that the

CLRC663 does not support a software reset

•The CLRC663 does not support the I2C device ID

•The implemented interface can only act in slave mode. Therefore no clock generation

and access arbitration is implemented in the CLRC663.

•High-speed mode is not supported by the CLRC663

001aam000

READER IC

SDA

SCL

PULL-UP

NETWORK

PULL-UP

NETWORK

MICROCONTROLLER

Figure 16. I2C-bus interface

The voltage level on the I2C pins is not allowed to be higher than PVDD.

SDA is a bidirectional line, connected to a positive supply voltage via a pull-up resistor.

Both lines SDA and SCL are set to HIGH level if no data is transmitted. Data on the I2C-

bus can be transferred at data rates of up to 400 kbit/s in fast mode, up to 1 Mbit/s in the

fast mode+.

If the I2C interface is selected, a spike suppression according to the I2C interface

specification on SCL and SDA is automatically activated.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 27 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

For timing requirements, refer to Table 256.

8.4.4.2 I2C Data validity

Data on the SDA line shall be stable during the HIGH period of the clock. The HIGH state

or LOW state of the data line shall only change when the clock signal on SCL is LOW.

001aam300

data line stable;

data valid

change

of data

allowed

SDA

SCL

Figure 17. Bit transfer on the I2C-bus

8.4.4.3 I2C START and STOP conditions

To handle the data transfer on the I2C-bus, unique START (S) and STOP (P) conditions

are defined.

A START condition is defined with a HIGH-to-LOW transition on the SDA line while SCL

is HIGH.

A STOP condition is defined with a LOW-to-HIGH transition on the SDA line while SCL is

HIGH.

The master always generates the START and STOP conditions. The bus is considered to

be busy after the START condition. The bus is considered to be free again a certain time

after the STOP condition.

The bus stays busy if a repeated START (Sr) is generated instead of a STOP condition.

In this respect, the START (S) and repeated START (Sr) conditions are functionally

identical. Therefore, the S symbol will be used as a generic term to represent both the

START and repeated START (Sr) conditions.

001aam301

START condition

SCL

SDA

SCL

SDA

STOP condition

Figure 18. START and STOP conditions

8.4.4.4 I2C byte format

Each byte has to be followed by an acknowledge bit. Data is transferred with the

MSB first, see Figure 18. The number of transmitted bytes during one data transfer is

unrestricted but shall fulfill the read/write cycle format.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 28 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.4.4.5 I2C Acknowledge

An acknowledge at the end of one data byte is mandatory. The acknowledge-related

clock pulse is generated by the master. The transmitter of data, either master or slave,

releases the SDA line (HIGH) during the acknowledge clock pulse. The receiver shall pull

down the SDA line during the acknowledge clock pulse so that it remains stable LOW

during the HIGH period of this clock pulse.

The master can then generate either a STOP (P) condition to stop the transfer, or a

repeated START (Sr) condition to start a new transfer.

A master-receiver shall indicate the end of data to the slave- transmitter by not

generating an acknowledge on the last byte that was clocked out by the slave. The slave-

transmitter shall release the data line to allow the master to generate a STOP (P) or

repeated START (Sr) condition.

001aam302

clock pulse for

acknowledgement

SCL FROM

MASTER

DATA OUTPUT

BY RECEIVERER

DATA OUTPUT

BY TRANSMITTER

2 8 9

acknowledge

START

condition

not acknowledge

Figure 19. Acknowledge on the I2C- bus

001aam303

MSB acknowledgement

signal from slave

acknowledgement

signal from receiver

clock line held low while

interrupts are serviced

byte complete,

interrupt within slave

1 2 7 8 9 1 2 9

ACK ACK

3 - 8 Sr

Figure 20. Data transfer on the I2C- bus

8.4.4.6 I2C 7-bit addressing

During the I2C-bus addressing procedure, the first byte after the START condition is used

to determine which slave will be selected by the master.

Alternatively the I2C address can be configured in the EEPROM. Several address

numbers are reserved for this purpose. During device configuration, the designer has to

ensure, that no collision with these reserved addresses in the system is possible. Check

the corresponding I2C specification for a complete list of reserved addresses.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 29 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

For all CLRC663 devices, the upper 5 bits of the device bus address are reserved by

NXP and set to 01010(bin). The remaining 2 bits (ADR_2, ADR_1) of the slave address

can be freely configured by the customer in order to prevent collisions with other I2C

devices by using the interface pins (refer to Table 16) or the value of the I2C address

EEPROM register (refer to Table 38).

001aam304

Bit 6 Bit 5 Bit 4

slave address

Bit 3 Bit 2 Bit 1 Bit 0 R/W

MSB LSB

Figure 21. First byte following the START procedure

8.4.4.7 I2C-register write access

To write data from the host controller via I2C to a specific register of the CLRC663, the

following frame format shall be used.

The read/write bit shall be set to logic 0.

The first byte of a frame indicates the device address according to the I2C rules. The

second byte indicates the register address followed by up to n-data bytes. In case the

address indicates the FIFO, in one frame all n-data bytes are written to the FIFO register

address. This enables for example a fast FIFO access.

8.4.4.8 I2C-register read access

To read out data from a specific register address of the CLRC663, the host controller

shall use the procedure:

First a write access to the specific register address has to be performed as indicated in

the following frame:

The first byte of a frame indicates the device address according to the I2C rules. The

second byte indicates the register address. No data bytes are added.

The read/write bit shall be logic 0.

Having performed this write access, the read access starts. The host sends the device

address of the CLRC663. As an answer to this device address, the CLRC663 responds

with the content of the addressed register. In one frame n-data bytes could be read

using the same register address. The address pointing to the register is incremented

automatically (exception: FIFO register address is not incremented automatically).

This enables a fast transfer of register content. The address pointer is incremented

automatically and data is read from the locations [address], [address+1], [address+2]...

[address+(n-1)]

In order to support a fast FIFO data transfer, the address pointer is not incremented

automatically in case the address is pointing to the FIFO.

The read/write bit shall be set to logic 1.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 30 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

001aam305

Ack

(W) Ack 0SA I2C slave address

A7-A0

Frontend IC register

address A6-A0 Ack

DATA

[7..0]

[0..n]

Ack

(W) Ack

Optional, if the previous access was on the same register address

Read Cycle

Write Cycle

0SA I2C slave address

A7-A0

Frontend IC register

address A6-A0

(R) AckSA

sent by master

sent by slave

I2C slave address

A7-A0 Ack

DATA

[7..0]

[0..n]

0..n

Nack

DATA

[7..0]

Figure 22. Register read and write access

8.4.4.9 I2CL-bus interface

The CLRC663 provides an additional interface option for connection of a SAM. This

logical interface fulfills the I2C specification, but the rise/fall timings will not be compliant

to the I2C standard. The I2CL interface uses standard I/O pads, and the communication

speed is limited to 5 MBaud. The protocol itself is equivalent to the fast mode protocol of

I2C. The SCL levels are generated by the host in push/pull mode. The RC663 does not

stretch the clock. During the high period of SCL, the status of the line is maintained by a

bus keeper.

The address is 01010xxb, where the last two bits of the address can be defined by the

application. The definition of these bits can be done by two options. With a pin, where

the higher bit is fixed to 0 or the configuration can be defined via EEPROM. Refer to the

EEPROM configuration in Section 8.7.

Parameter Min Max Unit

fSCL 0 5 MHz

tHD;STA 80 - ns

tLOW 100 - ns

tHIGH 100 - ns

tSU;SDA 80 - ns

tHD;DAT 0 50 ns

tSU;DAT 0 20 ns

tSU;STO 80 - ns

tBUF 200 - ns

Table 26. Timing parameter I2CL

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 31 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

The pull-up resistor is not required for the I2CL interface. Instead, a on chip buskeeper

is implemented in the CLRC663 for SDA of the I2CL interface. This protocol is intended

to be used for a point-to-point connection of devices over a short distance and does

not support a bus capability.The driver of the pin must force the line to the desired

logic voltage. To avoid that two drivers are pushing, the line at the same time following

regulations must be fulfilled:

SCL: As there is no clock stretching, the SCL is always under control of the Master.

SDA: The SDA line is shared between master and slave. Therefore the master and the

slave must have the control over the own driver enable line of the SDA pin. The following

rules must be followed:

•In the idle phase, the SDA line is driven high by the master

•In the time between start and stop condition, the SDA line is driven by master or slave

when SCL is low. If SCL is high, the SDA line is not driven by any device

•To keep the value on the SDA line a on chip, buskeeper structure is implemented for

the line

8.4.5 SAM interface

8.4.5.1 SAM functionality

The CLRC663 implements a dedicated I2C or SPI interface to integrate a MIFARE SAM

(Secure Access Module) in a very convenient way into applications (e.g. a proximity

reader).

The SAM can be connected to the microcontroller to operate like a cryptographic

coprocessor. For any cryptographic task, the microcontroller requests an operation from

the SAM, receives the answer and sends it over a host interface (e.g. I2C, SPI) interface

to the connected reader IC.

The MIFARE SAM supports an optimized method to integrate the SAM in a very

efficient way to reduce the protocol overhead. In this system configuration, the SAM is

integrated between the microprocessor and the reader IC, connected by one interface

to the reader IC and by another interface to the microcontroller. In this application, the

microcontroller accesses the SAM using the T=1 protocol and the SAM accesses the

reader IC using an I2C interface. The I2C SAM address is always defined by EEPROM

the communication overhead is reduced. In this configuration, a performance boost of up

to 40 % can be achieved for a transaction time.

The MIFARE SAM supports applications using MIFARE product-based cards. For multi-

application purposes, an architecture connecting the microcontroller additionally directly

to the reader IC is recommended. This is possible by connecting the CLRC663 on

one interface (SAM Interface SDA, SCL) with the MIFARE SAM AV2.6 (P5DF081XX/

T1AR1070) and by connecting the microcontroller to the S2C or SPI interface.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 32 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

µC

Reader

T=1 I2C

I2C

aaa-002963

SAM

AV2.6

READER

Figure 23. I2C interface enables convenient MIFARE SAM integration

8.4.5.2 SAM connection

The CLRC663 provides an interface to connect a SAM dedicated to the CLRC663. Both

interface options of the CLRC663, I2C, I2CL or SPI can be used for this purpose. The

interface option of the SAM itself is configured by a host command sent from the host to

the SAM.

The I2CL interface is intended to be used as connection between two ICs over a short

distance. The protocol fulfills the I2C specification, but does support a single device

connected to the bus only.

The SPI block for SAM connection is identical with the SPI host interface block.

The pins used for the SAM SPI are described in the following table:

SPI functionality PIN

MISO SDA2

SCL SCL2

MOSI IFSEL1

NSS IFSEL0

Table 27. SPI SAM connection

8.4.6 Boundary scan interface

The CLRC663 provides a boundary scan interface according to the IEEE 1149.1. This

interface allows testing interconnections without using physical test probes. This is done

by test cells, assigned to each pin, which override the functionality of this pin.

To be able to program the test cells, the following commands are supported:

Value

(decimal)

Command Parameter in Parameter out

0 bypass - -

1 preload data (24) -

2 sample - data (24)

3 ID code (default) - data (32)

4 USER code - data (32)

5 Clamp - -

6 HIGH Z - -

Table 28. Boundary scan command

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 33 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value

(decimal)

Command Parameter in Parameter out

7 extest data (24) data (24)

8 interface on/off interface (1) -

9 register access read address (7) data (8)

10 register access write address (7) - data (8) -

Table 28. Boundary scan command...continued

The Standard IEEE 1149.1 describes the four basic blocks necessary to use this

interface: Test Access Port (TAP), TAP controller, TAP instruction register, TAP data

8.4.6.1 Interface signals

The boundary scan interface implements a four line interface between the chip and the

environment. There are three Inputs: Test Clock (TCK); Test Mode Select (TMS); Test

Data Input (TDI) and one output Test Data Output (TDO). TCK and TMS are broadcast

signals, TDI to TDO generate a serial line called Scan path.

Advantage of this technique is that independent of the numbers of boundary scan

devices the complete path can be handled with four signal lines.

The signals TCK, TMS are directly connected with the boundary scan controller. Because

these signals are responsible for the mode of the chip, all boundary scan devices in one

scan path will be in the same boundary scan mode.

8.4.6.2 Test Clock (TCK)

The TCK pin is the input clock for the module. If this clock is provided, the test logic

is able to operate independent of any other system clocks. In addition, it ensures that

multiple boundary scan controllers that are daisy-chained together can synchronously

communicate serial test data between components. During normal operation, TCK

is driven by a free-running clock. When necessary, TCK can be stopped at 0 or 1 for

extended periods of time. While TCK is stopped at 0 or 1, the state of the boundary scan

controller does not change and data in the Instruction and Data Registers is not lost.

The internal pull-up resistor on the TCK pin is enabled. This assures that no clocking

occurs if the pin is not driven from an external source.

8.4.6.3 Test Mode Select (TMS)

The TMS pin selects the next state of the boundary scan controller. TMS is sampled on

the rising edge of TCK. Depending on the current boundary scan state and the sampled

value of TMS, the next state is entered. Because the TMS pin is sampled on the rising

edge of TCK, the IEEE Standard 1149.1 expects the value on TMS to change on the

falling edge of TCK.

Holding TMS high for five consecutive TCK cycles drives the boundary scan controller

state machine to the Test-Logic-Reset state. When the boundary scan controller enters

the Test-Logic-Reset state, the Instruction Register (IR) resets to the default instruction,

IDCODE. Therefore, this sequence can be used as a reset mechanism.

The internal pull-up resistor on the TMS pin is enabled.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 34 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.4.6.4 Test Data Input (TDI)

The TDI pin provides a stream of serial information to the IR chain and the DR chains.

TDI is sampled on the rising edge of TCK and, depending on the current TAP state and

the current instruction, presents this data to the proper shift register chain. Because the

TDI pin is sampled on the rising edge of TCK, the IEEE Standard 1149.1 expects the

value on TDI to change on the falling edge of TCK.

The internal pull-up resistor on the TDI pin is enabled.

8.4.6.5 Test Data Output (TDO)

The TDO pin provides an output stream of serial information from the IR chain or the

DR chains. The value of TDO depends on the current TAP state, the current instruction,

and the data in the chain being accessed. In order to save power when the port is not

being used, the TDO pin is placed in an inactive drive state when not actively shifting out

data. Because TDO can be connected to the TDI of another controller in a daisy-chain

configuration, the IEEE Standard 1149.1 expects the value on TDO to change on the

falling edge of TCK.

8.4.6.6 Data register

According to the IEEE1149.1 standard, there are two types of data register defined:

bypass and boundary scan

The bypass register enable the possibility to bypass a device when part of the scan

path.Serial data is allowed to be transferred through a device from the TDI pin to the

TDO pin without affecting the operation of the device.

The boundary scan register is the scan-chain of the boundary cells. The size of this

8.4.6.7 Boundary scan cell

The boundary scan cell opens the possibility to control a hardware pin independent of its

normal use case. Basically the cell can only do one of the following: control, output and

input.

001aam306

TAP

LOG

TAP

IC1 IC2

TCK TMSTCK TMS

TDOTDO

Boundary scan cell

TDITDI

Figure 24. Boundary scan cell path structure

8.4.6.8 Boundary scan path

This chapter shows the boundary scan path of the CLRC663.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 35 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Number (decimal) Cell Port Function

23 BC_1 - Control

22 BC_8 CLKOUT Bidir

21 BC_1 - Control

20 BC_8 SCL2 Bidir

19 BC_1 - Control

18 BC_8 SDA2 Bidir

17 BC_1 - Control

16 BC_8 IFSEL0 Bidir

15 BC_1 - Control

14 BC_8 IFSEL1 Bidir

13 BC_1 - Control

12 BC_8 IF0 Bidir

11 BC_1 - Control

10 BC_8 IF1 Bidir

9 BC_1 - Control

8 BC_8 IF2 Bidir

7 BC_1 IF2 Output2

6 BC_4 IF3 Input

5 BC_1 - Control

4 BC_8 IRQ Bidir

3 BC_1 - Control

2 BC_8 SIGIN Bidir

1 BC_1 - Control

0 BC_8 SIGOUT Bidir

Table 29. Boundary scan path of the CLRC663

Refer to the CLRC663 BSDL file.

8.4.6.9 Boundary Scan Description Language (BSDL)

All of the boundary scan devices have a unique boundary structure which is necessary to

know for operating the device. Important components of this language are:

•available test bus signal

•compliance pins

•command register

•data register

•boundary scan structure (number and types of the cells, their function and the

connection to the pins.)

The CLRC663 is using the cell BC_8 for the IO-Lines. The I2C Pin is using a BC_4 cell.

For all pad enable lines, the cell BC1 is used.

The manufacturer's identification is 02Bh.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 36 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

•attribute IDCODEISTER of CLRC663: entity is "0001" and -- version

•"0011110010000010b" and -- part number (3C82h)

•"00000010101b" and -- manufacturer (02Bh)

•"1b"; -- mandatory

The user code data is coded as followed:

•product ID (3 bytes)

•version

These four bytes are stored as the first four bytes in the EEPROM.

8.4.6.10 Non-IEEE1149.1 commands

Interface on/off

With this command, the host/SAM interface can be deactivated and the Read and Write

command of the boundary scan interface is activated. (Data = 1). With Update-DR, the

value is taken over.

At Capture-DR, the actual address is read and stored in the DR. Shifting the DR is

shifting in a new address. With Update-DR, this address is taken over into the actual

address.

At the Capture-DR, the address and the data is taken over from the DR. The data is

copied into the internal register at the given address.

8.5 Buffer

8.5.1 Overview

A 512 × 8-bit FIFO buffer is implemented in the CLRC663. It buffers the input and output

data stream between the host and the internal state machine of the CLRC663. Thus, it

is possible to handle data streams with lengths of up to 512 bytes without taking timing

constraints into account. The FIFO can also be limited to a size of 255 bytes. In this case

all the parameters (FIFO length, Watermark...) require a single byte only for definition. In

case of a 512 byte FIFO length, the definition of this value requires 2 bytes.

8.5.2 Accessing the FIFO buffer

When the μ-Controller starts a command, the CLRC663 may, while the command is in

progress, access the FIFO-buffer according to that command. Physically only one FIFO-

buffer is implemented, which can be used in input and output direction. Therefore the μ-

Controller has to take care, not to access the FIFO buffer in a way that corrupts the FIFO

data.

8.5.3 Controlling the FIFO buffer

Besides writing to and reading from the FIFO buffer, the FIFO-buffer pointers might be

reset by setting the bit FIFOFlush in FIFOControl to 1. Consequently, the FIFOLevel bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 37 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

are set to logic 0, the actually stored bytes are not accessible any more and the FIFO

buffer can be filled with another 512 bytes (or 255 bytes if the bit FIFOSize is set to 1)

again.

8.5.4 Status Information about the FIFO buffer

The host may obtain the following data about the FIFO-buffers status:

•Number of bytes already stored in the FIFO-buffer. Writing increments, reading

decrements the FIFO level: FIFOLength in register FIFOLength (and FIFOControl

•Warning, that the FIFO-buffer is almost full: HiAlert in register FIFOControl according

to the value of the water level in register WaterLevel (Register 02h bit [2], Register 03h

bit[7:0])

•Warning, that the FIFO-buffer is almost empty: LoAlert in register FIFOControl

according to the value of the water level in register WaterLevel (Register 02h bit [2],

•FIFOOvl bit indicates, that bytes were written to the FIFO buffer although it was already

full: ErrIRQ in register IRQ0.

WaterLevel is one single value defining both HiAlert (counting from the FIFO top) and

LoAlert (counting from the FIFO bottom). The CLRC663 can generate an interrupt signal

if:

•LoAlertIRQEn in register IRQ0En is set to logic 1 it will activate pin IRQ when LoAlert in

the register FIFOControl changes to 1.

•HiAlertIRQEN in register IRQ0En is set to logic 1 it will activate pin IRQ when HiAlert in

the register FIFOControl changes to 1.

The bit HiAlert is set to logic 1 if maximum water level bytes (as set in register

WaterLevel) or less can be stored in the FIFO-buffer. It is generated according to the

following equation:

(2)

The bit LoAlert is set to logic 1 if water level bytes (as set in register WaterLevel) or less

are actually stored in the FIFO-buffer. It is generated according to the following equation:

(3)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 38 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.6 Analog interface and contactless UART

8.6.1 General

The integrated contactless UART supports the external host online with framing and

error checking of the protocol requirements up to 848 kbit/s. An external circuit can be

connected to the communication interface pins SIGIN and SIGOUT to modulate and

demodulate the data.

The contactless UART handles the protocol requirements for the communication

schemes in co-operation with the host. The protocol handling itself generates bit- and

byte-oriented framing and handles error detection like Parity and CRC according to the

different contactless communication schemes.

The size, the tuning of the antenna, and the supply voltage of the output drivers have an

impact on the achievable field strength. The operating distance between reader and card

depends additionally on the type of card used.

8.6.2 TX transmitter

The signal delivered on pin TX1 and pin TX2 is the 13.56 MHz carrier modulated by an

envelope signal for energy and data transmission. It can be used to drive an antenna

directly, using a few passive components for matching and filtering, see Section 14. The

signal on TX1 and TX2 can be configured by the register DrvMode, see Section 9.8.1.

The modulation index can be set by the TxAmp.

Following figure shows the general relations during modulation

001aan355

time

influenced by set_clk_mode envelope

TX ASK100

1: Defined by set_cw_amplitude.

2: Defined by set_residual_carrier.

TX ASK10 (1)

(2)

Figure 25. General dependences of modulation

Note: When changing the continuous carrier amplitude, the residual carrier amplitude

also changes, while the modulation index remains the same.

The registers Section 9.8 and Section 9.10 control the data rate, the framing during

transmission and the setting of the antenna driver to support the requirements at the

different specified modes and transfer speeds.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 39 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

TxClkMode

(binary)

Tx1 and TX2 output Remarks

000 High impedance -

001 0 output pulled to 0 in any case

010 1 output pulled to 1 in any case

110 RF high side push open-drain, only high side (push) MOS supplied

with clock, clock parity defined by invtx; low

side MOS is off

101 RF low side pull open-drain, only low side (pull) MOS supplied

with clock, clock parity defined by invtx; high

side MOS is off

111 13.56 MHz clock derived

from 27.12 MHz quartz

divided by 2

push/pull Operation, clock polarity defined by

invtx; setting for 10 % modulation

Table 30. Settings for TX1 and TX2

set_residual_carrier (decimal) residual carrier [%] modulation index [%]

0 99 0.5

1 98 1.0

2 96 2.0

3 94 3.1

4 91 4.7

5 89 5.8

6 87 7.0

7 86 7.5

8 85 8.1

9 84 8.7

10 83 9.3

11 82 9.9

12 81 10.5

13 80 11.1

14 79 11.7

15 78 12.4

16 77 13.0

17 76 13.6

18 75 14.3

19 74 14.9

20 72 16.3

Table 31. Setting residual carrier and modulation index by

TXamp.set_residual_carrier

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 40 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

set_residual_carrier (decimal) residual carrier [%] modulation index [%]

21 70 17.6

22 68 19.0

23 65 21.2

24 60 25.0

25 55 29.0

26 50 33.3

27 45 37.9

28 40 42.9

29 35 48.1

30 30 53.8

31 25 60.0

Table 31. Setting residual carrier and modulation index by

TXamp.set_residual_carrier...continued

Note: At VDD(TVDD) <5 V and residual carrier settings <50 %, the accuracy of the

modulation index may be low in dependency of the antenna tuning impedance

8.6.2.1 Overshoot protection

The CLRC663 provides an overshoot protection for 100 % ASK to avoid overshoots

during a PCD communication. Therefore two timers overshoot_t1 and overshoot_t2 can

be used.

During the timer overshoot_t1 runs an amplitude defined by set_cw_amplitude bits is

provided to the output driver. Followed by an amplitude denoted by set_residual_carrier

bits with the duration of overshoot_t2.

001aan356

2.50 3.03 3.56 4.10

time ( s)

7.0

5.0

(V)

3.0

1.0

-1.0

Figure 26. Example 1: overshoot_t1 = 2d; overhoot_t2 = 5d.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 41 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

001aan357

-1.0 1 2 3 4 5

time ( s)

1.0

3.0

5.0

(V)

7.0

Figure 27. Example 2: overshoot_t1 = 0d; overhoot_t2 = 5d

8.6.2.2 Bit generator

The default coding of a data stream is done by using the Bit-Generator. It is activated

when the value of TxFrameCon.DCodeType is set to 0000 (bin). The Bit-Generator

encodes the data stream byte-wise and can apply the following encoding steps to each

data byte.

1. Add a start-bit of specified type at beginning of every byte

2. Add a stop-bit and EGT bits of a specified type. The maximum number of EGT bit is 6,

only full bits are supported

3. Add a parity-bit of a specified type

4. TxLastBits (skips a given number of bits at the end of the last byte in a frame)

5. Encrypt data-bit (MIFARE Classic encryption)

It is not possible to skip more than 8 bit of a single byte!

By default, data bytes are always treated LSB first.

8.6.3 Receiver circuitry

8.6.3.1 General

The CLRC663 features a versatile quadrature receiver architecture with fully differential

signal input at RXP and RXN. It can be configured to achieve optimum performance for

reception of various 13.56 MHz based protocols.

For all processing units various adjustments can be made to obtain optimum

performance.

8.6.3.2 Block diagram

The following figure shows the block diagram of the receiver circuitry. The receiving

process includes several steps. First the quadrature demodulation of the carrier signal of

13.56 MHz is done. Several tuning steps in this circuit are possible.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 42 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

001aan358

13.56 MHz

I/O CLOCK

GENERATION

I-clks

Q-clks

clk_27 MHz

TIMING

GENERATION

ADC

DATA

Adc_data_readyclk_27 MHz

mixer mix_out_i_p

2-stage BBA

mix_out_i_n

out_i_p

out_i_n

rx_p

rx_n

rx_p

rx_n

mixer

mix_out_q_p

2-stage BBA

mix_out_q_n

out_q_p

out_q_n

rcv_gain<1:0>

rcv_hpcf<1:0>fully/quasi-differential

fully/quasi-differential

rcv_gain<1:0>

rcv_hpcf<1:0>

rx_p

rx_n

Figure 28. Block diagram of receiver circuitry

The receiver can also be operated in a single ended mode. In this case, the

Rcv_RX_single bit has to be set. In the single ended mode, the two receiver pins RXP

and RXN need to be connected together and will provide a single ended signal to the

receiver circuitry.

When using the receiver in a single ended mode, the receiver sensitivity is decreased

and the achievable reading distance might be reduced, compared to the fully differential

mode.

Mode rcv_rx_single pins RXP and RXN

Fully differential 0 provide differential signal from differential antenna by

separate rx-coupling branches

Quasi differential 1 connect RXP and RXN together and provide single

ended signal from antenna by a single rx-coupling

branch

Table 32. Configuration for single or differential receiver

The quadrature-demodulator uses two different clocks, Q-clock and I-clock, with a

phase shift of 90° between them. Both resulting baseband signals are amplified, filtered,

digitized and forwarded to a correlation circuitry.

The typical application is intended to implement the Fully differential mode and

will deliver maximum reader/writer distance. The Quasi differential mode can be

used together with dedicated antenna topologies that allow a reduction of matching

components at the cost of overall reading performance.

During low-power card detection the DC levels at the I- and Q-channel mixer outputs

are evaluated. This requires that mixers are directly connected to the ADC. This can be

configured by setting the bit Rx_ADCmode in register Rcv (38h).

8.6.4 Active antenna concept

Two main blocks are implemented in the CLRC663. A digital circuitry, comprising state

machines, coder and decoder logic and an analog circuitry with the modulator and

antenna drivers, receiver and amplification circuitry. For example, the interface between

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 43 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

these two blocks can be configured in the way, that the interfacing signals may be routed

to the pins SIGIN and SIGOUT. The most important use of this topology is the active

antenna concept where the digital and the analog blocks are separated. This opens the

possibility to connect e.g. an additional digital block of another CLRC663 device with a

single analog antenna frontend.

001aam307

SIGIN

SIGINSIGOUT

SIGOUT

READER IC

(DIGITAL)

READER IC

(ANTENNA)

Figure 29. Block diagram of the active Antenna concept

The Table 33and Table 34 describe the necessary register configuration for the use case

active antenna concept.

SigOut.SigOutSel 0100 TxEnvelope

Rcv.SigInSel 10

Receive over SigIn (ISO/IEC14443A)

Receive over SigIn (Generic Code)

DrvCon.TxSel 00 Low (idle)

Table 33. Register configuration of CLRC663 active antenna concept (DIGITAL)

SigOut.SigOutSel 0110

0111

Generic Code (Manchester)

Manchester with Subcarrier (ISO/IEC14443A)

Rcv.SigInSel 01 Internal

DrvCon.TxSel 10 External (SigIn)

RxCtrl.RxMultiple 1 RxMultiple on

Table 34. Register configuration of CLRC663 active antenna concept (Antenna)

The interface between these two blocks can be configured in the way, that the interfacing

signals may be routed to the pins SIGIN and SIGOUT (see Figure 30).

This topology supports, that some parts of the analog part of the CLRC663 may be

connected to the digital part of another device.

The switch SigOutSel in registerSigOut can be used to measure signals. This is

especially important during the design-in phase or for test purposes to check the

transmitted and received data.

However, the most important use of SIGIN/SIGOUT pins is the active antenna concept.

An external active antenna circuit can be connected to the digital circuit of the CLRC663.

SigOutSel has to be configured in that way that the signal of the internal Miller Coder

is sent to SIGOUT pin (SigOutSel = 4). SigInSel has to be configured to receive

Manchester signal with subcarrier from SIGIN pin (SigInSel = 1).

It is possible, to connect a passive antenna to pins TX1, TX2 and RX (via the appropriate

filter and matching circuit) and at the same time an active antenna to the pins SIGOUT

and SIGIN. In this configuration, two RF-parts may be driven (one after another) by a

single host processor.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 44 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

001aam001

CODER SIGOUTSel[4:0]

Sigpro_in_sel

[1:0]

SIGOUT

SIGIN

TX bit stream

DIGITAL MODULE ANALOG MODULE

RX bit stream

0, 1

tri-state

LOW

HIGH

TX envelope

TX active

S3C signal

RX envelope

8RX active

RX bit signal

DECODER

SUBCARRIER

DEMODULATOR

TxCon.TxSel

[1:0]

No_nodulation

TX envelope

RFU

SIGIN

tri-state

internal analog block

SIGIN over envelope

SIGIN generic

MODULATOR DRIVER

TX2

TX1

RXN

RXP

DEMODULATOR

Figure 30. Overview SIGIN/SIGOUT Signal Routing

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 45 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.6.5 Symbol generator

The symbol generator is used to create various protocol symbols. These can be e.g.

SOF or EOF symbols as they are used by the ISO14443 protocols or proprietary protocol

symbols like the CS symbol as used by the ICODE EPC protocol.

Symbols are defined by means of the symbol definition registers and the mode registers.

Four different symbols can be used. Two of them, Symbol0 and Symbol1 have a

maximum pattern length of 16 bit and feature a burst length of up to 256 bits of either

logic "0" or logic "1". The Symbol2 and Symbol3 are limited to 8-bit pattern length and do

not support a burst.

The definition of symbol patterns is done by writing the bit sequence of the pattern to

the appropriate register. The last bit of the pattern to be sent is located at the LSB of

the register. By setting the symbol length in the symbol-length register (TxSym10Len

and TxSym32Len), the definition of the symbol pattern is completed. All other bits at bit-

position higher than the symbol length in the definition register are ignored. (Example:

length of Symbol2 = 5, bit7 and bit6 are ignored, bit5 to bit0 define the symbol pattern,

bit5 is sent first)

Which symbol-pattern is sent can be configured in the TxFrameCon register. Symbol0,

Symbol1 and Symbol2 can be sent before data packets, Symbol1, Symbol2 and Symbol3

can be sent after data packets. Each symbol is defined by a set of registers. Symbols are

configured by a pair of registers. Symbol0 and Symbol1 share the same configuration

and Symbol2 and Symbol3 share the same configuration. The configuration includes

setting of bit-clock- and subcarrier-frequency, as well as selection of the pulse type/length

and the envelope type.

8.7 Memory

8.7.1 Memory overview

The CLRC663 implements three different memories: EEPROM, FIFO and Registers.

At startup, the initialization of the registers which define the behavior of the IC is

performed by an automatic copy of an EEPROM area (read/write EEPROM section1

and section2, register reset) into the registers. The behavior of the CLRC663 can be

changed by executing the command LoadProtocol, which copies a selected default

protocol from the EEPROM (read-only EEPROM section4, register Set Protocol area)

into the registers.

The read/write EEPROM section2 can be used to store any user data or predefined

"LoadRegister" into the internal registers.

The FIFO is used as Input/Out buffer and is able to improve the performance of a system

with limited interface speed.

8.7.2 EEPROM memory organization

The CLRC663 has implemented a EEPROM non-volatile memory with a size of 8

kB.The EEPROM is organized in pages of 64 bytes. One page of 64 bytes can be

programmed at a time. Defined purposes had been assigned to specific memory areas

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 46 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

of the EEPROM, which are called Sections. Five sections 0..4 with different purpose do

exist.

Section Page Byte

addresses

Access

rights

Memory content

00 to 31 r product information and configuration0 0

32 to 63 r/w product configuration

1 1 to 2 64 to 191 r/w register reset

2 3 to 95 192 to 6143 r/w free

3 96 to 111 6144 to 7167 w MIFARE Classic key

4 112 to 128 7168 to 8191 r Register Set Protocol (RSP)

Table 35. EEPROM memory organization

The following figure shows the structure of the EEPROM:

001aan359

Production and configSection 0:

FreeSection 2:

MIFARE Classic

key area (MKA)

Section 3:

RSP-Area for TXSection 4_TX:

RSP-Area for RXSection 4_RX:

Figure 31. Sector arrangement of the EEPROM

8.7.2.1 Product information and configuration - Page 0

The first EEPROM page includes production data as well as configuration information.

Address

(Hex.)

0 1 2 3 4 5 6 7

00 ProductID Version Unique Identifier

08 Unique Identifier Manufacturer

Data

10 ManufacturerData

18 ManufacturerData

Table 36. Production area (Page 0)

ProductID: Identifier for this CLRC663 product or derivative, only address 01h shall be

evaluated for identifying the Product CLRC663, address 00h and 02h shall be ignored by

software.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 47 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Please note, that the silicon version CLRC66301, CLRC66302, CLRC66303 and

derivatives can be identified on register address 7Fh, it is not coded in the EEPROM

production area.

Address 01h Product ID

CLRC663 01h

MFRC631 C0h

MFRC630 80h

SLRC610 20h

Table 37. Product ID overview of CLRC663 family

Version: This register indicates the version of the EEPROM initialization data during

production.

Unique IDentifier: Unique serial number code for this device

Manufacturer Data: This data is programmed during production. The content is not

intended to be used by any application and might not be constant for different devices.

Therefore the content needs to be considered to be undefined.

Address

(Hex.)

0 1 2 3 4 5 6 7

20 I2C_Address Interface I2C SAM_Address DefaultProtRx DefaultProtTx - TxCRCPreset

28 RxCRCPreset - - - - - -

30 -

38 -

Table 38. Configuration area (Page 0)

I2C-Address

Two possibilities exist to define the address of the I2C interface. This can be done either

by configuring the pins IF0, IF2 (address is then 10101xx, xx is defined by the interface

pins IF0, IF2) or by writing value into the I2C address area. The selection, which of this

2-information pin configuration or EEPROM content - is used as I2C-address is done at

EEPROM address 21h (Interface, bit4)

Interface

This section describes the interface byte configuration.

Bit 7 6 5 4 3 2 1 0

I2C_HSP - - I2C_Address Boundary Scan Host

access rights r/w RFU RFU r/w r/w - - -

Table 39. Interface byte

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 48 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 I2C_HSP when cleared, the high-speed mode is used

when set, the high speed+ mode is used (default)

6, 5 RFU -

4 I2C_Address when cleared, the pins are used (default)

when set, the EEPROM is used

3 Boundary

Scan

when set, the boundary scan interface is ON (default)

when cleared, the boundary scan is OFF

2 to 0 Host 000b - RS232

001b - I2C

010b - SPI

011b - I2CL

1xxb - pin selection

Table 40. Interface bits

I2C_SAM_Address

The I2C SAM Address is always defined by the EEPROM content.

The Register Set Protocol (RSP) Area contains settings for the TX registers (16 bytes)

and for the RX registers (8 bytes).

Section

Section 4 TX Tx0 Tx1 TX2 Tx3

Section 4 TX Tx4 Tx5 TX6 TX7

Section 4 Rx RX0 RX1 RX2 RX3 RX4 RX5 RX6 RX7

Section 4 Rx RX8 RX9 RX10 RX11 RX12 RX13 RX14 RX15

Table 41. Tx and Rx arrangements in the register set protocol area

TxCrcPreset

The data bits are sent by the analog module and are automatically extended by a CRC.

8.7.3 EEPROM initialization content LoadProtocol

The CLRC663 EEPROM is initialized at production with values which are used to reset

certain registers of the CLRC663 to default settings by copying the EEPROM content

to the registers. Only registers or bits with "read/write" or "dynamic" access rights are

initialized with this default values copied from the EEPROM.

Note that the addresses used for copying reset values from EEPROM to registers are

dependent on the configured protocol and can be changed by the user.

Address 0 (8) 1 (9) 2 (A) 3 (B) 4 (C) 5 (D) 6 (E) 7 (F)

Function Product ID Version Unique Identifier

00 XX see table 34 XX XX XX XX XX XX

Function Unique Identifier Factory trim

value

Table 42. Register reset values (Hex.) (Page0)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 49 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Address 0 (8) 1 (9) 2 (A) 3 (B) 4 (C) 5 (D) 6 (E) 7 (F)

08 XX XX XX XX XX XX XX XX

Function TrimLFO Factory trim values

10 XX XX XX XX XX XX XX XX

Function Factory trim values

18.... XX XX XX XX XX XX XX XX

Factory trim values

....38 XX XX XX XX XX XX XX XX

Table 42. Register reset values (Hex.) (Page0)...continued

The register reset values are configuration parameters used after startup of the IC.

They can be changed to modify the default behavior of the device. In addition to these

protocols.The load protocol command is used for this purpose.

Address 0 (8) 1 (9) 2 (A) 3 (B) 4 (C) 5 (D) 6 (E) 7 (F)

Command HostCtrl FiFoControl WaterLevel FiFoLength FiFoData IRQ0 IRQ1

40 40 00 80 05 00 00 00 00

IRQ0En IRQ1En Error Status RxBitCtrl RxColl TControl T0Control

48 10 00 00 00 00 00 00 00

T0ReloadHi T0ReloadLo T0Counter

ValHi

T0Counter

ValLo

T1Control T1ReloadHi T1ReloadLo T1Counter

ValHi

50 00 80 00 00 00 00 80 00

T1Counter

ValLo

T2Control T2ReloadHi T2ReloadLo T2Counter

ValHi

T2Counter

ValLo

T3Control T3ReloadHi

58 00 00 00 80 00 00 00 00

T3ReloadLo T3Counter

ValHi

T3Counter

ValHi

T4Control T4ReloadHi T4ReloadLo T4Counter

ValHi

T4Counter

ValLo

60 80 00 00 00 00 80 00 00

DrvMode TxAmp DrvCon Txl TxCRC

Preset

RxCRC

Preset

TxDataNum TxModWith

68 86 15 11 06 18 18 08 27

TxSym10

BurstLen

TxWaitCtrl TxWaitLo FrameCon RxSofD RxCtrl RxWait RxThres

hold

70 00 C0 12 CF 00 04 90 3F

Rcv RxAna RFU SerialSpeed LFO_trimm PLL_Ctrl PLL_Div LPCD_QMin

78 12 0A 00 7A 80 04 20 48

LPCD_

QMax

LPCD_IMin LPCD _

result_I

LPCD _

result_Q

PadEn PadOut PadIn SigOut

Table 43. Register reset values (Hex.)(Page1 and page 2)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 50 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Address 0 (8) 1 (9) 2 (A) 3 (B) 4 (C) 5 (D) 6 (E) 7 (F)

80 12 88 00 00 00 00 00 00

TxBitMod RFU TxDataCon TxDataMod TxSymFreq TxSym0H TySym0L TxSym1H

88 20 xx 04 50 40 00 00 00

TxSym1L TxSym2 TxSym3 TxSym10Le

ngth

TxSym32Le

ngth

TxSym32Bu

rstCtrl

TxSym10M

TxSym32M

90 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x50

RxBitMod RxEOFSym RxSyncValH RxSyncValL RxSyncMod RxMod RXCorr FabCal

98 0x02 0x00 0x00 0x01 0x00 0x08 0x08 0xB2

Table 43. Register reset values (Hex.)(Page1 and page 2)...continued

8.8 Clock generation

8.8.1 Crystal oscillator

The clock applied to the CLRC663 acts as time basis for generation of the carrier sent

out at TX and for the quadrature mixer I and Q clock generation as well as for the coder

and decoder of the synchronous system. Therefore stability of the clock frequency is an

important factor for proper performance. To obtain highest performance, clock jitter has to

be as small as possible. This is best achieved by using the internal oscillator buffer with

the recommended circuitry.

001aam308

27.12 MHz

XTAL1 XTAL2

READER IC

Figure 32. Crystal connection

Symbol Parameter Conditions Min Typ max Unit

fxtal crystal frequency - 27.12 - MHz

Δfxtal/fxtal relative crystal

frequency variation

-250 - +250 ppm

ESR equivalent series

resistance

- 50 100 Ω

CLload capacitance - 10 - pF

Pxtal crystal power

dissipation

- 50 100 μW

Table 44. Crystal requirements recommendations

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 51 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.8.2 IntegerN PLL clock line

The CLRC663 is able to provide a clock with configurable frequency at CLKOUT from

1 MHz to 24 MHz (PLL_Ctrl and PLL_DIV). There it can serve as a clock source to a

microcontroller which avoids the need of a second crystal oscillator in the reader system.

Clock source for the IntegerN-PLL is the 27.12 MHz crystal oscillator.

Two dividers are determining the output frequency. First a feedback integer-N divider

configures the VCO frequency to be N × fin/2 (control signal pll_set_divfb). As supported

Feedback Divider Ratios are 23, 27 and 28, VCO frequencies can be 23 × fin / 2 (312

MHz), 27 × fin / 2 (366 MHz) and 28 × fin / 2 (380 MHz).

The VCO frequency is divided by a factor which is defined by the output divider

(pll_set_divout). The following table shows the accuracy achieved for various frequencies

(integer multiples of 1 MHz and some typical RS232 frequencies) and the divider ratios to

be used. The register bit ClkOutEn enables the clock at CLKOUT pin.

The following formula can be used to calculate the output frequency:

fout = 13.56 MHz × PLLDiv_FB /PLLDiv_Out

Frequency [MHz] 4 6 8 10 12 20 24 1.8432 3.6864

PLLDiv_FB 23 27 23 28 23 28 23 28 28

PLLDiv_Out 78 61 39 38 26 19 16 206 103

accuracy [%] 0.04 0.03 0.04 0.08 0.04 0.08 0.04 0.01 0.01

Table 45. Divider values for selected frequencies using the integerN PLL

8.8.3 Low Frequency Oscillator (LFO)

The CLRC663 family implements an Low-Frequency Oscillator (LFO). Timer T4 can be

configured to use a clock generated by this LFO as input clock, and can be configured

as wakeup counter. As wakeup counter, the timer T4 allows to wake up the system in

regular time intervals which allows to design a reader that is regularly polling for card

presence or implements a low-power card detection (LPCD).

The LFO is trimmed during chip production to run at 16 kHz. Unless a high accuracy

of the LFO is required by the application, and the device is operated in an environment

with changing ambient temperatures, trimming of the LFO is not required. For a typical

application making use of the LFO for wake-up from power saving mode, the trim value

set during production can be used.

Optional trimming to achieve a higher accuracy of the 16 kHz LFO clock is supported by

a digital state machine which compares LFO-clock to a reference clock generated by the

connected 27.12Mhz crystal. As reference clock frequency for trimming of the LFO, a

13.56 MHz clock (27.12Mhz divided by 2 ) input clock to one of the timers T0,T1,T2 or T3

is used.

One of the timers T0,T1,T2,T3 with an input clock of 13,56 MHz crystal clock is used to

count one clock period of the LFO. For an LFO Clock running at 16KHz this would result

in 848 wakeup timer clocks of timer Tx (T0, T1, T2, T3). Therefrore, the timer count value

Tx at the end of a trimming cycle is expected to be 176 (wakeup timer is counting down:

1023-848=175, +/- 1 tolerance is accepted). The trim cycle is executed once in the T4

timer cycle. Therefore the T4 autoload value shall be bigger than 0x05 to ensure that

one trimming cycle takes place before T4 expires. The Tx timer value is reloaded to 1023

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 52 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

during the start of an Auto trim cycle. This happens every time, once after the T4 timer

underflows.

At the end of each trim cycle, the timer value is checked:

•Timer Tx value < 174: LFO Frequency is too low and the trim value is incremented by 1

on T4 Timer event

•Timer Tx value > 176: LFO Frequency is too high and the trim value is decremented by

1 on T4 Timer event

•Timer Tx value is within 174 and 176: LFO Frequency = 16 KHz and trimming

procedure is stopped

The cycle proceeds until the autotrimm function is stopped (Timer Tx value is within 174

and 176).

In addition, the trimming cycle can be aborted by sending an IDLE Command from the

host to cancel the current command execution. T3 is not allowed to be used in case

T4AutoLPCD is set in parallel. It is not required to configure a TXStart condition with

underflow. The T0/1/2/3 timer will typically not underflow. It may happen if the LPO clock

is very slow, but it is not required to take an action to generate this event.

8.9 Power management

8.9.1 Supply concept

The CLRC663 is supplied by VDD (Supply Voltage), PVDD (Pad Supply) and TVDD

(Transmitter Power Supply). These three voltages are independent from each other.

To connect the CLRC663 to a Microcontroller supplied by 3.3 V, PVDD and VDD shall be

at a level of 3.3 V, TVDD can be in a range from 3.3 V to 5.0 V. A higher supply voltage at

TVDD results in a higher field strength.

Independent of the voltage it is recommended to buffer these supplies with blocking

capacitances close to the terminals of the package. VDD and PVDD are recommended to

be blocked with a capacitor of 100 nF min, TVDD is recommended to be blocked with 2

capacitors, 100 nF parallel to 1.0 μF

AVDD and DVDD are not supplied input pins. They are output pins and shall be

connected to blocking capacitors 470 nF each.

8.9.2 Power reduction mode

8.9.2.1 Power-down

A hard power-down is enabled with HIGH level on pin PDOWN. This turns off the internal

1.8 V voltage regulators for the analog and digital core supply as well as the oscillator.

All digital input buffers are separated from the input pads and clamped internally (except

pin PDOWN itself). The output pins are switched to high impedance. HardPowerDown is

performing a reset of the IC. All registers will be reset, the Fifo will be cleared.

To leave the power-down mode the level at the pin PDOWN as to be set to LOW. This

starts the internal start-up sequence.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 53 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.9.2.2 Standby mode

The standby mode is entered immediately after setting the bit PowerDown in the register

Command. All internal current sinks are switched off. Voltage references and voltage

regulators are set into standby mode.

In opposition to the power-down mode, the digital input buffers are not separated by the

input pads and keep their functionality. The digital output pins do not change their state.

During standby mode, all registers values, the FIFO’s content and the configuration itself

keeps its current content.

To leave the standby mode, the bit PowerDown in the register Command is cleared. This

triggers the internal start-up sequence. The reader IC is in full operation mode again

when the internal start-up sequence is finalized.

A value of 55h must be sent to the CLRC663 using the RS232 interface to leave the

standby mode. This is must at RS232, but cannot be used for the I2C/SPI interface. Then

read accesses shall be performed at address 00h until the device returns the content of

this address. The return of the content of address 00h indicates that the device is ready

to receive further commands and the internal start-up sequence is finalized.

8.9.2.3 Modem off mode

When the ModemOff bit in the register Control is set the antenna transmitter and the

receiver are switched off.

To leave the modem off mode, clears the ModemOff bit in the register Control.

8.9.3 Low-Power Card Detection (LPCD)

The low-power card detection is an energy saving mode in which the CLRC663 is not

fully powered permanently.

The LPCD works in two phases. First the standby phase is controlled by the wake-up

counter (WUC), which defines the duration of the standby of the CLRC663. Second

phase is the detection-phase. In this phase, the values of the I and Q channel are

detected and stored in the register map. (LPCD_I_Result, LPCD_Q_Result).This time

period can be handled with Timer3. The value is compared with the min/max values in

the registers (LPCD_IMin, LPCD_IMax; LPCD_QMin, LPCD_QMax). If it exceeds the

limits, an LPCDIRQ is raised.

After the command LPCD the standby of the CLRC663 is activated, if selected.

The wake-up Timer4 can activate the system after a given time. For the LPCD, it is

recommended to set T4AutoWakeUp and T4AutoRestart, to start the timer and then go to

standby. If a card is detected, the communication can be started. If T4AutoWakeUp is not

set, the IC will not enter Standby mode in case no card is detected.

8.9.4 Reset and start-up time

A 10 μs constant high level at the PDOWN pin starts the internal reset procedure.

The following figure shows the internal voltage regulator:

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 54 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

001aan360

PVDD

PDown

VSS

GLITCH

FILTER

INTERNAL VOLTAGE

REGULATOR

VDD

VSS

1.8 V

AVDD

DVDD

Figure 33. Internal PDown to voltage regulator logic

When the CLRC663 has finished, the reset phase and the oscillator has entered a stable

working condition the IC is ready to be used.

8.10 Command set

8.10.1 General

The behavior is determined by a state machine capable to perform a certain set of

commands. By writing a command-code to the command register, the command is

executed.

Arguments and/or data necessary to process a command, are exchanged via the FIFO

buffer.

•Each command that needs a certain number of arguments will start processing only

when it has received the correct number of arguments via the FIFO buffer.

•The FIFO buffer is not cleared automatically at command start. It is recommended to

write the command arguments and/or the data bytes into the FIFO buffer and start the

command afterwards.

•Each command may be stopped by the host by writing a new command code into the

command register e.g.: the Idle-Command.

8.10.2 Command set overview

Command No. Parameter (bytes) Short description

Idle 00h - no action, cancels current command execution

LPCD 01h - low-power card detection

LoadKey 02h (keybyte1),(keybyte2), (keybyte3),

(keybyte4), (keybyte5),(keybyte6);

reads a MIFARE Classic key (size of 6 bytes) from

FIFO buffer ant puts it into Key buffer

MFAuthent 03h 60h or 61h, (block address), (card

serial number byte0),(card serial

number byte1), (card serial number

byte2),(card serial number byte3);

performs the MIFARE Classic authentication

AckReq 04h - performs a query, an Ack and a Req-Rn for ISO/IEC

18000-3 mode 3/ EPC Class-1 HF

Receive 05h - activates the receive circuit

Transmit 06h bytes to send: byte1, byte2,.... transmits data from the FIFO buffer

Table 46. Command set

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 55 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Command No. Parameter (bytes) Short description

Transceive 07h bytes to send: byte1, byte2,.... transmits data from the FIFO buffer and automatically

activates the receiver after transmission finished

WriteE2 08h addressH, addressL, data; gets one byte from FIFO buffer and writes it to the

internal EEPROM

WriteE2Page 09h (page Address), data0,

[data1 ..data63];

gets up to 64 bytes (one EEPROM page) from the FIFO

buffer and writes it to the EEPROM

ReadE2 0Ah addressH, address L, length; reads data from the EEPROM and copies it into the

FIFO buffer

LoadReg 0Ch (EEPROM addressH), (EEPROM

addressL), RegAdr, (number of

reads data from the internal EEPROM and initializes

the CLRC663 registers. EEPROM address needs to be

within EEPROM sector 2

LoadProtocol 0Dh (Protocol number RX), (Protocol

number TX);

reads data from the internal EEPROM and initializes the

CLRC663 registers needed for a Protocol change

LoadKeyE2 0Eh KeyNr; copies a key from the EEPROM into the key buffer

StoreKeyE2 0Fh KeyNr, byte1,byte2, byte3, byte4,

byte5,byte6;

stores a MIFARE Classic key (size of 6 bytes) into the

EEPROM

ReadRNR 1Ch - Copies bytes from the Random Number generator into

the FIFO until the FiFo is full

Soft Reset 1Fh - resets the CLRC663

Table 46. Command set...continued

8.10.3 Command functionality

8.10.3.1 Idle command

Command (00h);

This command indicates that the CLRC663 is in idle mode. This command is also used to

terminate the actual command.

8.10.3.2 LPCD command

Command (01h);

This command performs a low-power card detection and/or an automatic trimming of

the LFO. After wake-up from standby, the values of the sampled I and Q channels are

compared with the min/max threshold values in the registers. If it exceeds the limits, an

LPCD_IRQ will be raised. After the LPCD command the standby is activated, if selected.

8.10.3.3 Load key command

Command (02h), Parameter1 (key byte1),..., Parameter6 (key byte6);

Loads a MIFARE Classic key (6 bytes) for Authentication from the FIFO into the crypto-

unit.

Abort condition: Less than 6 bytes written to the FIFO.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 56 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.10.3.4 MFAuthent command

Command (03h), Parameter1 (Authentication command code 60h or 61h), Parameter2

(block address), Parameter3 (card serial number byte0), Parameter4 (card serial number

byte1), Parameter5 (card serial number byte2), Parameter6 (card serial number byte3);

This command handles the MIFARE Classic authentication in Reader/Writer mode to

ensure a secure communication to any MIFARE classic card.

When the MFAuthent command is active, any FIFO access is blocked. Anyhow if there is

access to the FIFO, the bit WrErr in the Error register is set.

This command terminates automatically when the MIFARE Classic card is authenticated

and the bit MFCrypto1On is set to logic 1.

This command does not terminate automatically, when the card does not answer,

therefore the timer should be initialized to automatic mode. In this case, beside the bit

IdleIRQ the bit TimerIRQ can be used as termination criteria. During authentication

processing the bits RxIRQ and TxIRQ are blocked. The Crypto1On shows if the

authentication was successful. The Crypto1On is always valid.

In case, there is an error during authentication, the bit ProtocolErr in the Error register is

set to logic 1 and the bit Crypto1On in register Status2Reg is set to logic 0.

8.10.3.5 AckReq command

Command (04h);

Performs a Query (Full command must be written into the FIFO); an Ack and a ReqRn

command. All answers to the command will be written into the FIFO. The error flag is

copied after the answer into the FIFO.

This command terminates automatically and the then active state is idle.

8.10.3.6 Receive command

Command (05h);

The CLRC663 activates the receiver path and waits for any data stream to be received,

according to its register settings. The registers must be set before starting this command

according to the used protocol and antenna configuration. The correct settings have to be

chosen before starting the command.

This command terminates automatically when the received data stream ends. This

is indicated either by the end of frame pattern or by the length byte depending on the

selected framing and speed.

Remark: If the bit RxMultiple in the RxModeReg register is set to logic 1, the Receive

command does not terminate automatically. It has to be terminated by activating any

other command in the CommandReg register (see Section 9.17.6).

8.10.3.7 Transmit command

Command (06h); data to transmit

The content of the FIFO is transmitted immediately after starting the command. Before

transmitting the FIFO, all relevant registers have to be set to transmit data.

This command terminates automatically when the FIFO gets empty. It can be terminated

by any other command written to the command register.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 57 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.10.3.8 Transceive command

Command (07h); data to transmit

This command transmits data from FIFO buffer and automatically activates the receiver

after a transmission is finished.

Each transmission process starts by writing the command into CommandReg.

Remark: If the bit RxMultiple in register RxModeReg is set to logic 1, this command will

never leave the receiving state, because the receiving will not be cancelled automatically.

8.10.3.9 WriteE2 command

Command (08h), Parameter1 (addressH), Parameter2 (addressL), Parameter3 (data);

This command writes one byte into the EEPROM. If the FIFO contains no data, the

command will wait until the data is available.

Abort condition: Address-parameter outside of allowed range 0x00 – 0x7F.

8.10.3.10 WriteE2PAGE command

Command (09h), Parameter1 (page address), Parameter2..63 (data0, data1...data63);

This command writes up to 64 bytes into the EEPROM. The addresses are not allowed

to wrap over a page border. If this is the case, this additional data be ignored and stays

in the fifo. The programming starts after 64 bytes are read from the FIFO or the FIFO is

empty.

Abort condition: Insufficient parameters in FIFO; Page address parameter outside of

range 0x00 – 0x7F.

8.10.3.11 ReadE2 command

Command (0Ah), Parameter1 (addressH), Parameter2 (addressL), Parameter3 (length);

Reads up to 256 bytes from the EEPROM to the FIFO. If a read operation exceeds the

address 1FFFh, the read operation continues from address 0000h.

Abort condition: Insufficient parameter in FIFO; Address parameter outside of range.

8.10.3.12 LoadReg command

Command (0Ch), Parameter1 (EEPROM addressH),Parameter2 (EEPROM addressL),

Parameter3 (RegAdr), Parameter4 (number);

Read a defined number of bytes from the EEPROM and copies the value into the

Abort condition: Insufficient parameter in FIFO; Address parameter outside of range.

8.10.3.13 LoadProtocol command

Command (0Dh), Parameter1 (Protocol number RX), Parameter2 (Protocol number TX);

Reads out the EEPROM Register Set Protocol Area and overwrites the content of the

Rx- and Tx- related registers. These registers are important for a Protocol selection.

Abort condition: Insufficient parameter in FIFO

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 58 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Protocol

Number

(decimal)

Protocol Receiver speed

[kbits/s]

Receiver Coding

00 ISO/IEC14443 A 106 Manchester SubC

01 ISO/IEC14443 A 212 BPSK

02 ISO/IEC14443 A 424 BPSK

03 ISO/IEC14443 A 848 BPSK

04 ISO/IEC14443 B 106 BPSK

05 ISO/IEC14443 B 212 BPSK

06 ISO/IEC14443 B 424 BPSK

07 ISO/IEC14443 B 848 BPSK

08 FeliCa 212 Manchester

09 FeliCa 424 Manchester

10 ISO/IEC15693 26 SSC

11 ISO/IEC15693 52 SSC

12 ISO/IEC15693 26 DSC

13 EPC/UID 26 SSC

14 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

212 2/424

15 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

106 4/424

16 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

424 2/848

17 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

212 4/848

18 Jewel - -

Table 47. Predefined protocol overview RX[1]

[1] For more protocol details, please refer to Section 8.

Protocol

Number

(decimal)

Protocol Transmitter speed

[kbits/s]

Transmitter Coding

00 ISO/IEC14443 A 106 Miller

01 ISO/IEC14443 A 212 Miller

02 ISO/IEC14443 A 424 Miller

03 ISO/IEC14443 A 848 Miller

04 ISO/IEC14443 B 106 NRZ

05 ISO/IEC14443 B 212 NRZ

06 ISO/IEC14443 B 424 NRZ

Table 48. Predefined protocol overview TX[1]

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 59 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Protocol

Number

(decimal)

Protocol Transmitter speed

[kbits/s]

Transmitter Coding

07 ISO/IEC14443 B 848 NRZ

08 FeliCa 212 Manchester

09 FeliCa 424 Manchester

10 ISO/IEC15693 26 1/4

11 ISO/IEC15693 26 1/4

12 ISO/IEC15693 1,66 1/256

13 EPC/UID 53 Unitray

14 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

- based on Tari value,

ASK, PIE

15 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

- based on Tari value,

ASK, PIE

16 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

- based on Tari value,

ASK, PIE

17 ISO/IEC 18000-3 mode 3/

EPC Class-1 HF

- based on Tari value,

ASK, PIE

18 Jewel - -

Table 48. Predefined protocol overview TX[1]...continued

[1] For more protocol details, please refer to Section 8.

8.10.3.14 LoadKeyE2 command

Command (0Eh), Parameter1 (key number);

Loads a MIFARE Classic key for authentication from the EEPROM into the crypto 1 unit.

Abort condition: Insufficient parameter in FIFO; KeyNr is outside the MIFARE Classic key

area.

8.10.3.15 StoreKeyE2 command

Command (0Fh), Parameter1 (KeyNr), Parameter2(keybyte1), Parameter3(keybyte2),

Parameter4(keybyte3), Parameter5(keybyte4), Parameter6(keybyte5), Parameter7

(keybyte6);

Stores MIFARE Classic keys into the EEPROM. The key number parameter indicates

the first key (n) in the MKA that will be written. If more than one MIFARE Classic key is

available in the FIFO then the next key (n+1) will be written until the FIFO is empty. If an

incomplete key (less than 6 bytes) is written into the FIFO, this key will be ignored and

will remain in the FIFO.

Abort condition: Insufficient parameter in FIFO; KeyNr is outside the MKA;

8.10.3.16 GetRNR command

Command (1Ch);

This command is reading Random Numbers from the random number generator of the

CLRC663. The Random Numbers are copied to the FIFO until the FIFO is full.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 60 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.10.3.17 SoftReset command

Command (1Fh);

This command is performing a soft reset. Triggered by this command all the default

values for the register setting will be read from the EEPROM and copied into the register

set.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 61 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

9 CLRC663 registers

9.1 Register bit behavior

Depending on the functionality of a register, the access conditions to the register can

vary. In principle, bits with same behavior are grouped in common registers. The access

conditions are described in the table below:

Abbreviation Behavior Description

r/w read and write These bits can be written and read via the host interface. Since

they are used only for control purposes, the content is not

influenced by the state machines but can be read by internal

state machines.

dy dynamic These bits can be written and read via the host interface. They

can also be written automatically by internal state machines, for

example Command register changes its value automatically after

the execution of the command.

r read only These register bits indicate hold values which are determined by

internal states only.

w write only Reading these register bits always returns zero.

RFU - These bits are reserved for future use and must not be changed.

In case of a required write access, it is recommended to write a

logic 0.

Table 49. Behavior of register bits and their designation

Address Register name Function

00h Command Starts and stops command execution

01h HostCtrl Host control register

02h FIFOControl Control register of the FIFO

03h WaterLevel Level of the FIFO underflow and overflow warning

04h FIFOLength Length of the FIFO

05h FIFOData Data In/Out exchange register of FIFO buffer

06h IRQ0 Interrupt register 0

07h IRQ1 Interrupt register 1

08h IRQ0En Interrupt enable register 0

09h IRQ1En Interrupt enable register 1

0Ah Error Error bits showing the error status of the last command execution

0Bh Status Contains status of the communication

0Ch RxBitCtrl Control register for anticollision adjustments for bit oriented protocols

0Dh RxColl Collision position register

0Eh TControl Control of Timer 0..3

Table 50. CLRC663 registers overview

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 62 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Address Register name Function

0Fh T0Control Control of Timer0

10h T0ReloadHi High register of the reload value of Timer0

11h T0ReloadLo Low register of the reload value of Timer0

12h T0CounterValHi Counter value high register of Timer0

13h T0CounterValLo Counter value low register of Timer0

14h T1Control Control of Timer1

15h T1ReloadHi High register of the reload value of Timer1

16h T1ReloadLo Low register of the reload value of Timer1

17h T1CounterValHi Counter value high register of Timer1

18h T1CounterValLo Counter value low register of Timer1

19h T2Control Control of Timer2

1Ah T2ReloadHi High byte of the reload value of Timer2

1Bh T2ReloadLo Low byte of the reload value of Timer2

1Ch T2CounterValHi Counter value high byte of Timer2

1Dh T2CounterValLo Counter value low byte of Timer2

1Eh T3Control Control of Timer3

1Fh T3ReloadHi High byte of the reload value of Timer3

20h T3ReloadLo Low byte of the reload value of Timer3

21h T3CounterValHi Counter value high byte of Timer3

22h T3CounterValLo Counter value low byte of Timer3

23h T4Control Control of Timer4

24h T4ReloadHi High byte of the reload value of Timer4

25h T4ReloadLo Low byte of the reload value of Timer4

26h T4CounterValHi Counter value high byte of Timer4

27h T4CounterValLo Counter value low byte of Timer4

28h DrvMode Driver mode register

29h TxAmp Transmitter amplifier register

2Ah DrvCon Driver configuration register

2Bh Txl Transmitter register

2Ch TxCrcPreset Transmitter CRC control register, preset value

2Dh RxCrcPreset Receiver CRC control register, preset value

2Eh TxDataNum Transmitter data number register

2Fh TxModWidth Transmitter modulation width register

30h TxSym10BurstLen Transmitter symbol 1 + symbol 0 burst length register

31h TXWaitCtrl Transmitter wait control

32h TxWaitLo Transmitter wait low

Table 50. CLRC663 registers overview...continued

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 63 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Address Register name Function

33h FrameCon Transmitter frame control

34h RxSofD Receiver start of frame detection

35h RxCtrl Receiver control register

36h RxWait Receiver wait register

37h RxThreshold Receiver threshold register

38h Rcv Receiver register

39h RxAna Receiver analog register

RFU No function implemented for CLRC66301 and CLRC663023Ah

LPCD_Options For CLRC66303: Options for LPCD configuration

3Bh SerialSpeed Serial speed register

3Ch LFO_Trimm Low-power oscillator trimming register

3Dh PLL_Ctrl IntegerN PLL control register, for microcontroller clock output adjustment

3Eh PLL_DivOut IntegerN PLL control register, for microcontroller clock output adjustment

3Fh LPCD_QMin Low-power card detection Q channel minimum threshold

40h LPCD_QMax Low-power card detection Q channel maximum threshold

41h LPCD_IMin Low-power card detection I channel minimum threshold

42h LPCD_I_Result Low-power card detection I channel result register

43h LPCD_Q_Result Low-power card detection Q channel result register

44h PadEn PIN enable register

45h PadOut PIN out register

46h PadIn PIN in register

47h SigOut Enables and controls the SIGOUT Pin

48h TxBitMod Transmitter bit mode register

49h RFU -

4Ah TxDataCon Transmitter data configuration register

4Bh TxDataMod Transmitter data modulation register

4Ch TxSymFreq Transmitter symbol frequency

4Dh TxSym0H Transmitter symbol 0 high register

4Eh TxSym0L Transmitter symbol 0 low register

4Fh TxSym1H Transmitter symbol 1 high register

50h TxSym1L Transmitter symbol 1 low register

51h TxSym2 Transmitter symbol 2 register

52h TxSym3 Transmitter symbol 3 register

53h TxSym10Len Transmitter symbol 1 + symbol 0 length register

54h TxSym32Len Transmitter symbol 3 + symbol 2 length register

55h TxSym10BurstCtrl Transmitter symbol 1 + symbol 0 burst control register

Table 50. CLRC663 registers overview...continued

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 64 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Address Register name Function

56h TxSym10Mod Transmitter symbol 1 + symbol 0 modulation register

57h TxSym32Mod Transmitter symbol 3 + symbol 2 modulation register

58h RxBitMod Receiver bit modulation register

59h RxEofSym Receiver end of frame symbol register

5Ah RxSyncValH Receiver synchronisation value high register

5Bh RxSyncValL Receiver synchronisation value low register

5Ch RxSyncMod Receiver synchronisation mode register

5Dh RxMod Receiver modulation register

5Eh RxCorr Receiver correlation register

5Fh FabCal Calibration register of the receiver, calibration performed at production

48h-5Fh RFU -

7Fh Version Version and subversion register

Table 50. CLRC663 registers overview...continued

9.2 Command configuration

9.2.1 Command

Starts and stops command execution.

Bit 7 6 5 4 3 2 1 0

Symbol Standby Modem

Off

RFU Command

Access

rights

dy r/w - dy

Table 51. Command register (address 00h)

Bit Symbol Description

7 Standby Set to 1, the IC is entering power-down mode.

6 ModemOff Set to logic 1, the receiver and the transmitter circuit is powering

down.

5 RFU -

4 to 0 Command Defines the actual command for the CLRC663.

Table 52. Command bits

9.3 SAM configuration register

9.3.1 HostCtrl

Via the HostCtrl Register the interface access right can be controlled

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 65 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit 7 6 5 4 3 2 1 0

Symbol RegEn BusHost BusSAM RFU SAMInterface SAMInterface RFU RFU

Access

rights

dy r/w r/w - r/w r/w - -

Table 53. HostCtrl register (address 01h);

Bit Symbol Description

7 RegEn If this bit is set to logic 1, the register HostCtrl_reg can be changed

at the next register access. The next write access clears this bit

automatically.

6 BusHost Set to logic 1, the bus is controlled by the host. This bit cannot be set

together with the bit BusSAM. This bit can only be set if the bit RegEn

is previously set.

5 BusSAM Set to logic 1, the bus is controlled by the SAM. This bit cannot be

set together with BusHost. This bit can only be set if the bit RegEn is

previously set.

4 RFU -

3 to 2 SAMInterface 0h:SAM Interface switched off

1h:SAM Interface SPI active

2h:SAM Interface I2CL active

3h:SAM Interface I2C active

1 to 0 RFU -

Table 54. HostCtrl bits

9.4 FIFO configuration register

9.4.1 FIFOControl

FIFOControl defines the characteristics of the FIFO

Bit 7 6 5 4 3 2 1 0

Symbol FIFOSize HiAlert LoAlert FIFOFlush RFU WaterLe

velExtBit

FIFOLengthExtBits

Access

rights

r/w r r w - r/w r

Table 55. FIFOControl register (address 02h);

Bit Symbol Description

7 FIFOSize Set to logic 1, FIFO size is 255 bytes;

Set to logic 0, FIFO size is 512 bytes.

It is recommended to change the FIFO size only, when the FIFO

content had been cleared.

Table 56. FIFOControl bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 66 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

6 HiAlert Set to logic 1, when the number of bytes stored in the FIFO buffer

fulfils the following equation:

HiAlert = (FIFOSize - FIFOLength) <= WaterLevel

5 LoAlert Set to logic 1, when the number of bytes stored in the FIFO buffer

fulfils the following conditions:

LoAlert =1 if FIFOLength <= WaterLevel

4 FIFOFlush Set to logic 1 clears the FIFO buffer. Reading this bit will always

return 0

3 RFU -

2 WaterLevelExtBit Defines the bit 8 (MSB) for the waterlevel (extension of register

WaterLevel). This bit is only evaluated in the 512-byte FIFO mode.

Bits 7..0 are defined in register WaterLevel.

1 to 0 FIFOLengthExtBits Defines the bit9 (MSB) and bit8 for the FIFO length (extension of

FIFOLength). These two bits are only evaluated in the 512-byte

FIFO mode. The bits 7..0 are defined in register FIFOLength.

Table 56. FIFOControl bits...continued

9.4.2 WaterLevel

Defines the level for FIFO under- and overflow warning levels.This register is extended

by 1 bit in FIFOControl in case the 512-byte FIFO mode is activated by setting bit

FIFOControl.FIFOSize.

Bit 76543210

Symbol WaterLevelBits

Access

rights

r/w r/w r/w r/w r/w r/w r/w r/w

Table 57. WaterLevel register (address 03h);

Bit Symbol Description

7 to 0 WaterLevelBits Sets a level to indicate a FIFO-buffer state which can be read

from bits HighAlert and LowAlert in the FifoControl. In 512-byte

FIFO mode, the register is extended by bit WaterLevelExtBit in the

FIFOControl. This functionality can be used to avoid a FIFO buffer

overflow or underflow:

The bit HiAlert bit in FIFO Control is read logic 1, if the number of

bytes in the FIFO-buffer is equal or less than the number defined by

the waterlevel configuration.

The bit LoAlert bit in FIFO control is read logic 1, if the number of

bytes in the FIFO buffer is equal or less than the number defined by

the waterlevel configuration.

Note: For the calculation of HiAlert and LoAlert, see register

description of these bits (see section Section 9.4.1).

Table 58. WaterLevel bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 67 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

9.4.3 FIFOLength

Number of bytes in the FIFO buffer. In 512-byte mode, this register is extended by

FIFOControl.FifoLength.

Bit 76543210

Symbol FIFOLength

Access

rights

Table 59. FIFOLength register (address 04h); reset value: 00h

Bit Symbol Description

7 to 0 FIFOLength Indicates the number of bytes in the FIFO buffer. In 512-byte mode

this register is extended by the bits FIFOLength in the FIFOControl

decrements the number of available bytes in the FIFO.

Table 60. FIFOLength bits

9.4.4 FIFOData

In- and output of FIFO buffer. Contrary to any read/write access to other addresses,

reading or writing to the FIFO address does not increment the address pointer. Writing

to the FIFOData register increments, reading decrements the number of bytes present in

the FIFO.

Bit 76543210

Symbol FIFOData

Access

rights

dy dy dy dy dy dy dy dy

Table 61. FIFOData register (address 05h);

Bit Symbol Description

7 to 0 FIFOData Data input and output port for the internal FIFO buffer. Refer to

Section 8.5.

Table 62. FIFOData bits

9.5 Interrupt configuration registers

The Registers IRQ0 register and IRQ1 register implement a special functionality to avoid

the unintended modification of bits.

The mechanism of changing register contents requires the following consideration:

IRQ(x).Set indicates, if a set bit on position 0 to 6 shall be cleared or set. Depending

on the content of IRQ(x).Set, a write of a 1 to positions 0 to 6 either clears or sets the

corresponding bit. With this register, the application can modify the interrupt status which

is maintained by the CLRC663.

Bit 7 indicates, if the intended modification is a setting or clearance of a bit. Any 1 written

to a bit position 6...0 will trigger the setting or clearance of this bit as defined by bit 7.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 68 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Example: writing FFh sets all bits 6..0, writing 7Fh clears all bits 6..0 of the interrupt

request register

9.5.1 IRQ0 register

Interrupt request register 0.

Bit 7 6 5 4 3 2 1 0

Symbol Set HiAlertIRQ LoAlertIRQ IdleIRQ TxIRQ RxIRQ ErrIRQ RxSOF

IRQ

Access

rights

w dy dy dy dy dy dy dy

Table 63. IRQ0 register (address 06h); reset value: 00h

Bit Symbol Description

7 Set 1: writing a 1 to a bit position 6..0 sets the interrupt request

0: Writing a 1 to a bit position 6..0 clears the interrupt request

6 HiAlertIRQ Set, when bit HiAlert in register Status1Reg is set. In opposition to HiAlert,

HiAlertIRQ stores this event.

5 LoAlertIRQ Set, when bit LoAlert in register Status1 is set. In opposition to LoAlert,

LoAlertIRQ stores this event.

4 IdleIRQ Set, when a command terminates by itself e.g. when the Command

changes its value from any command to the Idle command. If an unknown

command is started, the Command changes its content to the idle state and

the bit IdleIRQ is set. Starting the Idle command by the Controller does not

set bit IdleIRQ.

3 TxIRQ Set, when data transmission is completed, which is immediately after the

last bit is sent.

2 RxIRQ Set, when the receiver detects the end of a data stream.

Note: This flag is no indication that the received data stream is correct. The

error flags have to be evaluated to get the status of the reception.

1 ErrIRQ Set, when the one of the following errors is set:

FifoWrErr, FiFoOvl, ProtErr, NoDataErr, IntegErr.

0 RxSOFlrq Set, when a SOF or a subcarrier is detected.

Table 64. IRQ0 bits

9.5.2 IRQ1 register

Interrupt request register 1.

Bit 7 6 5 4 3 2 1 0

Symbol Set GlobalIRQ LPCD_IRQ Timer4IRQ Timer3IRQ Timer2IRQ Timer1IRQ Timer0IRQ

Access

rights

w dy dy dy dy dy dy dy

Table 65. IRQ1 register (address 07h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 69 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 Set 1: writing a 1 to a bit position 5..0 sets the interrupt request

0: Writing a 1 to a bit position 5..0 clears the interrupt request

6 GlobalIRQ Set, if an enabled IRQ occurs.

5 LPCD_IRQ Set if a card is detected in Low-power card detection sequence.

4 Timer4IRQ Set to logic 1 when Timer4 has an underflow.

3 Timer3IRQ Set to logic 1 when Timer3 has an underflow.

2 Timer2IRQ Set to logic 1 when Timer2 has an underflow.

1 Timer1IRQ Set to logic 1 when Timer1 has an underflow.

0 Timer0IRQ Set to logic 1 when Timer0 has an underflow.

Table 66. IRQ1 bits

9.5.3 IRQ0En register

Interrupt request enable register for IRQ0. This register allows defining if an interrupt

request is processed by the CLRC663.

Bit 7 6 5 4 3 2 1 0

Symbol IRQ_Inv Hi AlertIRQEn LoAlertIRQEn IdleIRQEn TxIRQEn RxIRQEn ErrIRQEn RxSOF

IRQEn

Access

rights

r/w r/w r/w r/w r/w r/w r/w r/w

Table 67. IRQ0En register (address 08h)

Bit Symbol Description

7 IRQ_Inv Set to one the signal of the IRQ pin is inverted

6 Hi AlerIRQEn Set to logic 1, it allows the High Alert interrupt Request (indicated by the

bit HiAlertIRQ) to be propagated to the GlobalIRQ

5 Lo AlertIRQEn Set to logic 1, it allows the Low Alert Interrupt Request (indicated by the

bit LoAlertIRQ) to be propagated to the GlobalIRQ

4 IdleIRQEn Set to logic 1, it allows the Idle interrupt request (indicated by the bit

IdleIRQ) to be propagated to the GlobalIRQ

3 TxIRQEn Set to logic 1, it allows the transmitter interrupt request (indicated by the

bit TxtIRQ) to be propagated to the GlobalIRQ

2 RxIRQEn Set to logic 1, it allows the receiver interrupt request (indicated by the bit

RxIRQ) to be propagated to the GlobalIRQ

1 ErrIRQEn Set to logic 1, it allows the Error interrupt request (indicated by the bit

ErrorIRQ) to be propagated to the GlobalIRQ

0 RxSOFIRQEn Set to logic 1, it allows the RxSOF interrupt request (indicated by the bit

RxSOFIRQ) to be propagated to the GlobalIRQ

Table 68. IRQ0En bits

9.5.4 IRQ1En

Interrupt request enable register for IRQ1.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 70 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit 7 6 5 4 3 2 1 0

Symbol IRQPushPull IRQPinEn LPCD_IRQEn Timer4

IRQEn

Timer3

IRQEn

Timer2

IRQEn

Timer1

IRQEn

Timer0

IRQEn

Access

rights

r/w r/w r/w r/w r/w r/w r/w r/w

Table 69. IRQ1EN register (address 09h);

Bit Symbol Description

7 IRQPushPull Set to 1 the IRQ-pin acts as PushPull pin, otherwise it acts as

OpenDrain pin

6 IRQPinEN Set to logic 1, it allows the global interrupt request (indicated by the bit

GlobalIRQ) to be propagated to the interrupt pin

5 LPCD_IRQEN Set to logic 1, it allows the LPCDinterrupt request (indicated by the bit

LPCDIRQ) to be propagated to the GlobalIRQ

4 Timer4IRQEn Set to logic 1, it allows the Timer4 interrupt request (indicated by the bit

Timer4IRQ) to be propagated to the GlobalIRQ

3 Timer3IRQEn Set to logic 1, it allows the Timer3 interrupt request (indicated by the bit

Timer3IRQ) to be propagated to the GlobalIRQ

2 Timer2IRQEn Set to logic 1, it allows the Timer2 interrupt request (indicated by the bit

Timer2IRQ) to be propagated to the GlobalIRQ

1 Timer1IRQEn Set to logic 1, it allows the Timer1 interrupt request (indicated by the bit

Timer1IRQ) to be propagated to the GlobalIRQ

0 Timer0IRQEn Set to logic 1, it allows the Timer0 interrupt request (indicated by the bit

Timer0IRQ) to be propagated to the GlobalIRQ

Table 70. IRQ1EN bits

9.6 Contactless interface configuration registers

9.6.1 Error

Error register.

Bit 7 6 5 4 3 2 1 0

Symbol EE_Err FiFoWrErr FIFOOvl MinFrameErr NoDataErr CollDet ProtErr IntegErr

Access

rights

dy dy dy dy dy dy dy dy

Table 71. Error register (address 0Ah)

Bit Symbol Description

7 EE_Err An error appeared during the last EEPROM command. For

details see the descriptions of the EEPROM commands

Table 72. Error bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 71 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

6 FIFOWrErr Data was written into the FIFO, during a transmission of a possible

CRC, during "RxWait", "Wait for data" or "Receiving" state, or during an

authentication command. The Flag is cleared when a new CL command is

started. If RxMultiple is active, the flag is cleared after the error flags have

been written to the FIFO.

5 FIFOOvl Data is written into the FIFO when it is already full. The data that is already

in the FIFO remains untouched. All data that is written to the FIFO after this

Flag is set to 1 will be ignored.

4 Min

FrameErr

A valid SOF was received, but afterwards less than 4 bits of data were

received.

Note: Frames with less than 4 bits of data are automatically discarded and

the RxDecoder stays enabled. Furthermore no RxIRQ is set. The same is

valid for less than 3 bytes, if the EMD suppression is activated

Note: MinFrameErr is automatically cleared at the start of a receive or

transceive command. In case of a transceive command, it is cleared at the

start of the receiving phase ("Wait for data" state)

3 NoDataErr Data should be sent, but no data is in FIFO

2 CollDet A collision has occurred. The position of the first collision is shown in the

Note: CollDet is automatically cleared at the start of a receive or transceive

command. In case of a transceive command, it is cleared at the start of the

receiving phase ("Wait for data" state).

Note: If a collision is part of the defined EOF symbol, CollDet is not set to 1.

1 ProtErr A protocol error has occurred. A protocol error can be a wrong stop bit,

a missing or wrong ISO/IEC14443B EOF or SOF or a wrong number of

received data bytes. When a protocol error is detected, data reception is

stopped.

Note: ProtErr is automatically cleared at start of a receive or transceive

command. In case of a transceive command, it is cleared at the start of the

receiving phase ("Wait for data" state).

Note: When a protocol error occurs the last received data byte is not written

into the FIFO.

0 IntegErr A data integrity error has been detected. Possible cause can be a wrong

parity or a wrong CRC. In case of a data integrity error the reception is

continued.

Note: IntegErr is automatically cleared at start of a Receive or Transceive

command. In case of a Transceive command, it is cleared at the start of the

receiving phase ("Wait for data" state).

Note: If the NoColl bit is set, also a collision is setting the IntegErr.

Table 72. Error bits...continued

9.6.2 Status

Status register.

Bit 76543210

Symbol - - Crypto1On - - ComState

Access

rights

RFU RFU dy RFU RFU r

Table 73. Status register (address 0Bh)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 72 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 6 - RFU

5 Crypto1On Indicates if the MIFARE Classic Crypto is on. Clearing this bit is switching

the MIFARE Cassic Crypto off. The bit can only be set by the MFAuthent

command.

4 to 3 - RFU

ComState shows the status of the transmitter and receiver state machine:

000b ... Idle

001b ... TxWait

011b ... Transmitting

101b ... RxWait

110b ... Wait for data

111b ... Receiving

2 to 0 ComState

100b ... not used

Table 74. Status bits

9.6.3 RxBitCtrl

Receiver control register.

Bit 7 6 5 4 3 2 1 0

Symbol ValuesAfterColl RxAlign NoColl RxLastBits

Access

rights

r/w r/w r/w r/w r/w w w w

Table 75. RxBitCtrl register (address 0Ch);

Bit Symbol Description

7 ValuesAfter

Coll

If cleared, every received bit after a collision is replaced by a zero. This

function is needed for ISO/IEC14443 anticollision

6 to 4 RxAlign Used for reception of bit oriented frames: RxAlign defines the bit position

length for the first bit received to be stored. Further received bits are

stored at the following bit positions.

Example:

RxAlign = 0h - the LSB of the received bit is stored at bit 0, the second

received bit is stored at bit position 1.

RxAlign = 1h - the LSB of the received bit is stored at bit 1, the second

received bit is stored at bit position 2.

RxAlign = 7h - the LSB of the received bit is stored at bit 7, the second

received bit is stored in the following byte at position 0.

Note: If RxAlign = 0, data is received byte-oriented, otherwise bit-

oriented.

3 NoColl If this bit is set, a collision will result in an IntegErr

Table 76. RxBitCtrl bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 73 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

2 to 0 RxLastBits Defines the number of valid bits of the last data byte received in bit-

oriented communications. If zero the whole byte is valid.

Note: These bits are set by the RxDecoder in a bit-oriented

communication at the end of the communication. They are reset at start

of reception.

Table 76. RxBitCtrl bits...continued

9.6.4 RxColl

Receiver collision register.

Bit 7 6 5 4 3 2 1 0

Symbol CollPosValid CollPos

Access

rights

r r

Table 77. RxColl register (address 0Dh);

Bit Symbol Description

7 CollPos

Valid

If set to 1, the value of CollPos is valid. Otherwise no collision is detected or

the position of the collision is out of the range of bits CollPos.

6 to 0 CollPos These bits show the bit position of the first detected collision in a received

frame (only data bits are interpreted). CollPos can only be displayed for the

first 8 bytes of a data stream.

Example:

00h indicates a bit collision in the 1st bit

01h indicates a bit collision in the 2nd bit

08h indicates a bit collision in the 9th bit (1st bit of 2nd byte)

3Fh indicates a bit collision in the 64th bit (8th bit of the 8th byte)

These bits shall only be interpreted in Passive communication mode at 106

kbit/s or ISO/IEC 14443 type A and read /write mode for MIFARE Classic or

ISO/IEC 15693/ICODE SLI read/write mode if bit CollPosValid is set.

Note: If RxBitCtrl.RxAlign is set to a value different to 0, this value is

included in the CollPos.

Example: RxAlign = 4h, a collision occurs in the 4th received bit (which is

the last bit of that UID byte). The CollPos = 7h in this case.

Table 78. RxColl bits

9.7 Timer configuration registers

9.7.1 TControl

Control register of the timer section.

The TControl implements a special functionality to avoid the not intended modification of

bits.

Bit 3..0 indicates, which bits in the positions 7..4 are intended to be modified.

Example: writing FFh sets all bits 7..4, writing F0h does not change any of the bits 7..4

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 74 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit 7 6 5 4 3 2 1 0

Symbol T3Running T2Running T1Running T0Running T3Start

StopNow

T2Start

StopNow

T1Start

StopNow

T0Start

StopNow

Access

rights

dy dy dy dy w w w w

Table 79. TControl register (address 0Eh)

Bit Symbol Description

7 T3Running Indicates Timer3 is running.If the bit T3startStopNow is set/reset, this

bit and the timer can be started/stopped

6 T2Running Indicates Timer2 is running. If the bit T2startStopNow is set/reset, this

bit and the timer can be started/stopped

5 T1Running Indicates tTmer1 is running. If the bit T1startStopNow is set/reset, this

bit and the timer can be started/stopped

4 T0Running Indicates Timer0 is running. If the bit T0startStopNow is set/reset, this

bit and the timer can be started/stopped

3 T3StartStop

Now

The bit 7 of TControl T3Running can be modified if set

2 T2StartStop

Now

The bit 6of TControl T2Running can be modified if set

1 T1StartStop

Now

The bit 5of TControl T1Running can be modified if set

0 T0StartStop

Now

The bit 4 of TControl T0Running can be modified if set

Table 80. TControl bits

9.7.2 T0Control

Control register of the Timer0.

Bit 7 6 5 4 3 2 1 0

Symbol T0StopRx - T0Start T0AutoRestart - T0Clk

Access

rights

r/w RFU r/w r/w RFU r/w

Table 81. T0Control register (address 0Fh);

Bit Symbol Description

7 T0StopRx If set, the timer stops immediately after receiving the first 4 bits. If

cleared the timer does not stop automatically.

Note: If LFO Trimming is selected by T0Start, this bit has no effect.

6 - RFU

Table 82. T0Control bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 75 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

5 to 4 T0Start 00b: The timer is not started automatically

01 b: The timer starts automatically at the end of the transmission

10 b: Timer is used for LFO trimming without underflow (Start/Stop on

PosEdge)

11 b: Timer is used for LFO trimming with underflow (Start/Stop on

PosEdge)

3 T0AutoRestart 1: the timer automatically restarts its count-down from

T0ReloadValue, after the counter value has reached the value zero.

0: the timer decrements to zero and stops.

The bit Timer1IRQ is set to logic 1 when the timer underflows.

2 - RFU

1 to 0 T0Clk 00 b: The timer input clock is 13.56 MHz.

01 b: The timer input clock is 211,875 kHz.

10 b: The timer input clock is an underflow of Timer2.

11 b: The timer input clock is an underflow of Timer1.

Table 82. T0Control bits...continued

9.7.2.1 T0ReloadHi

High byte reload value of the Timer0.

Bit 7 6 5 4 3 2 1 0

Symbol T0Reload Hi

Access

rights

r/w

Table 83. T0ReloadHi register (address 10h);

Bit Symbol Description

7 to 0 T0ReloadHi Defines the high byte of the reload value of the timer. With the start

event, the timer loads the value of the registers T0ReloadValHi,

T0ReloadValLo. Changing this register affects the timer only at the

next start event.

Table 84. T0ReloadHi bits

9.7.2.2 T0ReloadLo

Low byte reload value of the Timer0.

Bit 7 6 5 4 3 2 1 0

Symbol T0ReloadLo

Access

rights

r/w

Table 85. T0ReloadLo register (address 11h);

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 76 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to0 T0ReloadLo Defines the low byte of the reload value of the timer. With the

start event, the timer loads the value of the T0ReloadValHi,

T0ReloadValLo. Changing this register affects the timer only at the

next start event.

Table 86. T0ReloadLo bits

9.7.2.3 T0CounterValHi

High byte of the counter value of Timer0.

Bit 7 6 5 4 3 2 1 0

Symbol T0CounterValHi

Access

rights

Table 87. T0CounterValHi register (address 12h)

Bit Symbol Description

7to0 T0Counter

ValHi

High byte value of the Timer0.

This value shall not be read out during reception.

Table 88. T0CounterValHi bits

9.7.2.4 T0CounterValLo

Low byte of the counter value of Timer0.

Bit 7 6 5 4 3 2 1 0

Symbol T0CounterValLo

Access

rights

Table 89. T0CounterValLo register (address 13h)

Bit Symbol Description

7 to 0 T0CounterValLo Low byte value of the Timer0.

This value shall not be read out during reception.

Table 90. T0CounterValLo bits

9.7.2.5 T1Control

Control register of the Timer1.

Bit 7 6 5 4 3 2 1 0

Symbol T1StopRx - T1Start T1AutoRestart - T1Clk

Access

rights

r/w RFU r/w r/w RFU r/w

Table 91. T1Control register (address 14h);

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 77 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 T1StopRx If set, the timer stops after receiving the first 4 bits. If cleared, the

timer is not stopped automatically.

Note: If LFO trimming is selected by T1start, this bit has no effect.

6 - RFU

5 to 4 T1Start 00b: The timer is not started automatically

01 b: The timer starts automatically at the end of the transmission

10 b: Timer is used for LFO trimming without underflow (Start/Stop on

PosEdge)

11 b: Timer is used for LFO trimming with underflow (Start/Stop on

PosEdge)

3 T1AutoRestart Set to logic 1, the timer automatically restarts its countdown from

T1ReloadValue, after the counter value has reached the value zero.

Set to logic 0 the timer decrements to zero and stops.

The bit Timer1IRQ is set to logic 1 when the timer underflows.

2 - RFU

1 to 0 T1Clk 00 b: The timer input clock is 13.56 MHz

01 b: The timer input clock is 211,875 kHz.

10 b: The timer input clock is an underflow of Timer0

11 b: The timer input clock is an underflow of Timer2

Table 92. T1Control bits

9.7.2.6 T1ReloadHi

High byte (MSB) reload value of the Timer1.

Bit 7 6 5 4 3 2 1 0

Symbol T1ReloadHi

Access

rights

r/w

Table 93. T0ReloadHi register (address 15h)

Bit Symbol Description

7 to 0 T1ReloadHi Defines the high byte reload value of the Timer 1. With the start event,

the timer loads the value of the T1ReloadValHi and T1ReloadValLo.

Changing this register affects the Timer only at the next start event.

Table 94. T1ReloadHi bits

9.7.2.7 T1ReloadLo

Low byte (LSB) reload value of the Timer1.

Bit 7 6 5 4 3 2 1 0

Symbol T1ReloadLo

Access

rights

r/w

Table 95. T1ReloadLo register (address 16h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 78 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 0 T1ReloadLo Defines the low byte of the reload value of the Timer1. Changing this

Table 96. T1ReloadLo bits

9.7.2.8 T1CounterValHi

High byte (MSB) of the counter value of byte Timer1.

Bit 7 6 5 4 3 2 1 0

Symbol T1CounterValHi

Access

rights

Table 97. T1CounterValHi register (address 17h)

Bit Symbol Description

7 to 0 T1Counter

ValHi

High byte of the current value of the Timer1.

This value shall not be read out during reception.

Table 98. T1CounterValHi bits

9.7.2.9 T1CounterValLo

Low byte (LSB) of the counter value of byte Timer1.

Bit 7 6 5 4 3 2 1 0

Symbol T1CounterValLo

Access

rights

Table 99. T1CounterValLo register (address 18h)

Bit Symbol Description

7 to 0 T1Counter

ValLo

Low byte of the current value of the counter 1.

This value shall not be read out during reception.

Table 100. T1CounterValLo bits

9.7.2.10 T2Control

Control register of the Timer2.

Bit 7 6 5 4 3 2 1 0

Symbol T2StopRx - T2Start T2AutoRestart - T2Clk

Access

rights

r/w RFU r/w r/w RFU r/w

Table 101. T2Control register (address 19h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 79 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 T2StopRx If set the timer stops immediately after receiving the first 4 bits. If

cleared indicates, that the timer is not stopped automatically.

Note: If LFO Trimming is selected by T2Start, this bit has no effect.

6 - RFU

5 to 4 T2Start 00 b: The timer is not started automatically.

01 b: The timer starts automatically at the end of the transmission.

10 b: Timer is used for LFO trimming without underflow (Start/Stop on

PosEdge).

11 b: Timer is used for LFO trimming with underflow (Start/Stop on

PosEdge).

3 T2AutoRestart Set to logic 1, the timer automatically restarts its countdown from

T2ReloadValue, after the counter value has reached the value

zero. Set to logic 0 the timer decrements to zero and stops. The bit

Timer2IRQ is set to logic 1 when the timer underflows

2 - RFU

1 to 0 T2Clk 00 b: The timer input clock is 13.56 MHz.

01 b: The timer input clock is 212 kHz.

10 b: The timer input clock is an underflow of Timer0

11b: The timer input clock is an underflow of Timer1

Table 102. T2Control bits

9.7.2.11 T2ReloadHi

High byte of the reload value of Timer2.

Bit 7 6 5 4 3 2 1 0

Symbol T2ReloadHi

Access

rights

r/w

Table 103. T2ReloadHi register (address 1Ah)

Bit Symbol Description

7 to 0 T2ReloadHi Defines the high byte of the reload value of the Timer2. With the

start event, the timer load the value of the T2ReloadValHi and

T2ReloadValLo. Changing this register affects the timer only at the

next start event.

Table 104. T2ReloadHi bits

9.7.2.12 T2ReloadLo

Low byte of the reload value of Timer2.

Bit 7 6 5 4 3 2 1 0

Symbol T2ReloadLo

Access

rights

r/w

Table 105. T2ReloadLo register (address 1Bh)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 80 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 0 T2ReloadLo Defines the low byte of the reload value of the Timer2. With the

start event, the timer load the value of the T2ReloadValHi and

T2RelaodVaLo. Changing this register affects the timer only at the

next start event.

Table 106. T2ReloadLo bits

9.7.2.13 T2CounterValHi

High byte of the counter register of Timer2.

Bit 7 6 5 4 3 2 1 0

Symbol T2CounterValHi

Access

rights

Table 107. T2CounterValHi register (address 1Ch)

Bit Symbol Description

7 to 0 T2Counter

ValHi

High byte current counter value of Timer2.

This value shall not be read out during reception.

Table 108. T2CounterValHi bits

9.7.2.14 T2CounterValLoReg

Low byte of the current value of Timer 2.

Bit 7 6 5 4 3 2 1 0

Symbol T2CounterValLo

Access

rights

Table 109. T2CounterValLo register (address 1Dh)

Bit Symbol Description

7 to 0 T2Counter

ValLo

Low byte of the current counter value of Timer1Timer2.

This value shall not be read out during reception.

Table 110. T2CounterValLo bits

9.7.2.15 T3Control

Control register of the Timer 3.

Bit 7 6 5 4 3 2 1 0

Symbol T3StopRx - T3Start T3AutoRestart - T3Clk

Access

rights

r/w RFU r/w r/w RFU r/w

Table 111. T3Control register (address 1Eh)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 81 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 T3StopRx If set, the timer stops immediately after receiving the first 4 bits. If

cleared, indicates that the timer is not stopped automatically.

Note: If LFO Trimming is selected by T3Start, this bit has no effect.

6 - RFU

5 to 4 T3Start 00b - timer is not started automatically

01 b - timer starts automatically at the end of the transmission

10 b - timer is used for LFO trimming without underflow (Start/Stop on

PosEdge)

11 b - timer is used for LFO trimming with underflow (Start/Stop on

PosEdge).

3 T3AutoRestart Set to logic 1, the timer automatically restarts its countdown from

T3ReloadValue, after the counter value has reached the value zero.

Set to logic 0 the timer decrements to zero and stops.

The bit Timer1IRQ is set to logic 1 when the timer underflows.

2 - RFU

1 to 0 T3Clk 00 b - the timer input clock is 13.56 MHz.

01 b - the timer input clock is 211,875 kHz.

10 b - the timer input clock is an underflow of Timer0

11 b - the timer input clock is an underflow of Timer1

Table 112. T3Control bits

9.7.2.16 T3ReloadHi

High byte of the reload value of Timer3.

Bit 7 6 5 4 3 2 1 0

Symbol T3ReloadHi

Access

rights

r/w

Table 113. T3ReloadHi register (address 1Fh);

Bit Symbol Description

7 to 0 T3ReloadHi Defines the high byte of the reload value of the Timer3. With the

start event, the timer load the value of the T3ReloadValHi and

T3ReloadValLo. Changing this register affects the timer only at the

next start event.

Table 114. T3ReloadHi bits

9.7.2.17 T3ReloadLo

Low byte of the reload value of Timer3.

Bit 7 6 5 4 3 2 1 0

Symbol T3ReloadLo

Access

rights

r/w

Table 115. T3ReloadLo register (address 20h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 82 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 0 T3ReloadLo Defines the low byte of the reload value of Timer3. With the

start event, the timer load the value of the T3ReloadValHi and

T3RelaodValLo. Changing this register affects the timer only at the

next start event.

Table 116. T3ReloadLo bits

9.7.2.18 T3CounterValHi

High byte of the current counter value the 16-bit Timer3.

Bit 7 6 5 4 3 2 1 0

Symbol T3CounterValHi

Access

rights

Table 117. T3CounterValHi register (address 21h)

Bit Symbol Description

7 to 0 T3Counter

ValHi

High byte of the current counter value of Timer3.

This value shall not be read out during reception.

Table 118. T3CounterValHi bits

9.7.2.19 T3CounterValLo

Low byte of the current counter value the 16-bit Timer3.

Bit 7 6 5 4 3 2 1 0

Symbol T3CounterValLo

Access

rights

Table 119. T3CounterValLo register (address 22h)

Bit Symbol Description

7 to 0 T3Counter

ValLo

Low byte current counter value of Timer3.

This value shall not be read out during reception.

Table 120. T3CounterValLo bits

9.7.2.20 T4Control

The wake-up timer T4 activates the system after a given time. If enabled, it can start the

low-power card detection function.

Bit 7 6 5 4 3 2 1 0

Symbol T4Running T4Start

StopNow

T4Auto

Trimm

T4Auto

LPCD

T4Auto

Restart

T4AutoWakeUp T4Clk

Table 121. T4Control register (address 23h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 83 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit 7 6 5 4 3 2 1 0

Access

rights

dy w r/w r/w r/w r/w r/w

Table 121. T4Control register (address 23h)...continued

Bit Symbol Description

7 T4Running Shows if the timer T4 is running. If the bit T4StartStopNow is set,

this bit and the timer T4 can be started/stopped.

6 T4Start

StopNow

if set, the bit T4Running can be changed.

5 T4AutoTrimm If set to one, the timer activates an LFO trimming procedure when it

underflows. For the T4AutoTrimm function, at least one timer (T0 to

T3) has to be configured properly for trimming (T3 is not allowed if

T4AutoLPCD is set in parallel).

4 T4AutoLPCD If set to one, the timer activates a low-power card detection

sequence. If a card is detected an interrupt request is raised and

the system remains active if enabled. If no card is detected the

CLRC663 enters the Power down mode if enabled. The timer is

automatically restarted (no gap). Timer 3 is used to specify the time

where the RF field is enabled to check if a card is present. Therefore

you may not use Timer 3 for T4AutoTrimm in parallel.

3 T4AutoRestart Set to logic 1, the timer automatically restarts its countdown from

T4ReloadValue, after the counter value has reached the value

zero. Set to logic 0 the timer decrements to zero and stops. The bit

Timer4IRQ is set to logic 1 at timer underflow.

2 T4AutoWakeUp If set, the CLRC663 wakes up automatically, when the timer T4 has

an underflow. This bit has to be set if the IC should enter the Power

down mode after T4AutoTrimm and/or T4AutoLPCD is finished and

no card has been detected. If the IC should stay active after one of

these procedures, this bit has to be set to 0.

1 to 0 T4Clk 00b - the timer input clock is the LFO clock

01b - the timer input clock is the LFO clock/8

10b - the timer input clock is the LFO clock/16

11b - the timer input clock is the LFO clock/32

Table 122. T4Control bits

9.7.2.21 T4ReloadHi

High byte of the reload value of the 16-bit timer 4.

Bit 7 6 5 4 3 2 1 0

Symbol T4ReloadHi

Access

rights

r/w

Table 123. T4ReloadHi register (address 24h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 84 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 0 T4ReloadHi Defines high byte for the reload value of timer 4. With the start event,

the timer 4 loads the T4ReloadVal. Changing this register affects the

timer only at the next start event.

Table 124. T4ReloadHi bits

9.7.2.22 T4ReloadLo

Low byte of the reload value of the 16-bit timer 4.

Bit 7 6 5 4 3 2 1 0

Symbol T4ReloadLo

Access

rights

r/w

Table 125. T4ReloadLo register (address 25h)

Bit Symbol Description

7 to 0 T4ReloadLo Defines the low byte of the reload value of the timer 4. With the start

event, the timer loads the value of the T4ReloadVal. Changing this

Table 126. T4ReloadLo bits

9.7.2.23 T4CounterValHi

High byte of the counter value of the 16-bit timer 4.

Bit 7 6 5 4 3 2 1 0

Symbol T4CounterValHi

Access

rights

Table 127. T4CounterValHi register (address 26h)

Bit Symbol Description

7 to 0 T4CounterValHi High byte of the current counter value of timer 4.

Table 128. T4CounterValHi bits

9.7.2.24 T4CounterValLo

Low byte of the counter value of the 16-bit timer 4.

Bit 7 6 5 4 3 2 1 0

Symbol T4CounterValLo

Access

rights

Table 129. T4CounterValLo register (address 27h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 85 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 0 T4CounterValLo Low byte of the current counter value of the timer 4.

Table 130. T4CounterValLo bits

9.8 Transmitter driver configuration registers

9.8.1 DrvMode

Bit 7 6 5 4 3 2 1 0

Symbol Tx2Inv Tx1Inv - - TxEn TxClk Mode

Access

rights

r/w r/w RFU RFU r/w r/w

Table 131. DrvMode register (address 28h)

Bit Symbol Description

7 Tx2Inv Inverts transmitter 2 at TX2 pin

6 Tx1Inv Inverts transmitter 1 at TX1 pin

5 RFU

4 - RFU

3 TxEn If set to 1 both transmitter pins are enabled

2 to 0 TxClkMode Transmitter clock settings. Codes 011b and 0b110 are not supported.

This register defines, if the output is operated in open-drain, push-pull,

at high impedance or pulled to a fix high or low level.

Table 132. DrvMode bits

9.8.2 TxAmp

With the set_cw_amplitude register, output power can be traded off against power supply

rejection. Spending more headroom leads to better power supply rejection ration and

better accuracy of the modulation degree.

With CwMax set, the voltage of TX1 will be pulled to the maximum possible. This register

overrides the settings made by set_cw_amplitude.

Bit 7 6 5 4 3 2 1 0

Symbol set_cw_amplitude - set_residual_carrier

Access

rights

r/w RFU r/w

Table 133. TxAmp register (address 29h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 86 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 6 set_cw_amplitude Allows reducing the output amplitude of the transmitter by a fix

value.

Four different preset values that are subtracted from TVDD

can be selected:

0: TVDD -100 mV

1: TVDD -250 mV

2: TVDD -500 mV

3: TVDD -1000 mV

5 RFU -

4 to 0 set_residual_ carrier Set the residual carrier percentage. refer to section

Section 8.6.2.

Table 134. TxAmp bits

9.8.3 TxCon

Bit 7 6 5 4 3 2 1 0

Symbol OvershootT2 CwMax TxInv TxSel

Access

rights

r/w r/w r/w r/w

Table 135. TxCon register (address 2Ah)

Bit Symbol Description

7 to 4 OvershootT2 Specifies the length (number of carrier clocks) of the additional

modulation for overshoot prevention. Refer to section Section 8.6.2.1.

3 Cwmax Set amplitude of continuous wave carrier to the maximum.

If set, set_cw_amplitude in Register TxAmp has no influence on the

continuous amplitude.

2 TxInv If set, the resulting modulation signal defined by TxSel is inverted

1 to 0 TxSel Defines which signal is used as source for modulation

00b ... no modulation

01b ... TxEnvelope

10b ... SigIn

11b ... RFU

Table 136. TxCon bits

9.8.4 Txl

Bit 7 6 5 4 3 2 1 0

Symbol OvershootT1 tx_set_iLoad

Access

rights

r/w r/w

Table 137. Txl register (address 2Bh)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 87 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 4 OvershootT1 Overshoot value for Timer1. Refer to Section Section 8.6.2.1.

3 to 0 tx_set_iLoad Factory trim value, sets the expected Tx load current. This value is

used to control the modulation index in an optimized way dependent

on the expected TX load current.

Table 138. Txl bits

9.9 Transmitter CRC configuration registers

9.9.1 TxCrcPreset

Bit 7 6 5 4 3 2 1 0

Symbol RFU TXPresetVal TxCRCtype TxCRCInvert TxCRCEn

Access

rights

- r/w r/w r/w r/w

Table 139. TXCrcPreset register (address 2Ch)

Bit Symbol Description

7 RFU -

6 to 4 TXPresetVal Specifies the CRC preset value for transmission (see following table).

3 to 2 TxCRCtype Defines which type of CRC (CRC8/CRC16/CRC5) is calculated:

•00h -- CRC5

•01h -- CRC8

•02h -- CRC16

•03h -- RFU

1 TxCRCInvert if set, the resulting CRC is inverted and attached to the data frame

(ISO/IEC 3309)

0 TxCRCEn if set, a CRC is appended to the data stream

Table 140. TxCrcPreset bits

TXPresetVal[6...4] CRC16 CRC8 CRC5

0h 0000h 00h 00h

1h 6363h 12h 12h

2h A671h BFh -

3h FFFEh FDh -

4h - - -

5h - - -

6h User defined User defined User defined

7h FFFFh FFh 1Fh

Table 141. Transmitter CRC preset value configuration

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 88 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Remark: User-defined CRC preset values can be configured by EEPROM (see section

Section 8.7.2.1, Table 38.

9.9.2 RxCrcCon

Bit 7 6 5 4 3 2 1 0

Symbol RxForceCRCWrite RXPresetVal RXCRCtype RxCRCInvert RxCRCEn

Access

rights

r/w r/w r/w r/w r/w

Table 142. RxCrcCon register (address 2Dh)

Bit Symbol Description

7 RxForceCrc

Write

If set, the received CRC byte(s) are copied to the FIFO.

If cleared CRC Bytes are only checked, but not copied to the FIFO.

This bit has to be always set in case of a not byte aligned CRC (e.g.

ISO/IEC 18000-3 mode 3/ EPC Class-1HF)

6 to 4 RXPresetVal Defines the CRC preset value (Hex.) for transmission. (see following

table).

3 to 2 RxCRCtype Defines which type of CRC (CRC8/CRC16/CRC5) is calculated:

•00h -- CRC5

•01h -- CRC8

•02h -- CRC16

•03h -- RFU

1 RxCrcInvert If set, the CRC check is done for the inverted CRC.

0 RxCrcEn If set, the CRC is checked and in case of a wrong CRC an error flag is

set. Otherwise the CRC is calculated but the error flag is not modified.

Table 143. RxCrcCon bits

RXPresetVal[6...4] CRC16 CRC8 CRC5

0h 0000h 00h 00h

1h 6363h 12h 12h

2h A671h BFh -

3h FFFEh FDh -

4h - - -

5h - - -

6h User defined User defined User defined

7h FFFFh FFh 1Fh

Table 144. Receiver CRC preset value configuration

9.10 Transmitter data configuration registers

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 89 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

9.10.1 TxDataNum

Bit 7 6 5 4 3 2 1 0

Symbol RFU RFU- RFU- KeepBitGrid DataEn TxLastBits

Access

rights

r/w r/w r/w

Table 145. TxDataNum register (address 2Eh)

Bit Symbol Description

7 to 5 RFU -

4 KeepBitGrid If set, the time between consecutive transmissions starts is a multiple

of one ETU. If cleared, consecutive transmissions can even start

within one ETU

3 DataEn If cleared - it is possible to send a single symbol pattern.

If set - data is sent.

2 to 0 TxLastBits Defines how many bits of the last data byte to be sent. If set to 000b,

all bits of the last data byte are sent.

Note - bits are skipped at the end of the byte.

Example - Data byte B2h (sent LSB first).

TxLastBits = 011b (3h) => 010b (LSB first) is sent

TxLastBits = 110b (6h) => 010011b (LSB first) is sent

Table 146. TxDataNum bits

9.10.2 TxDATAModWidth

Transmitter data modulation width register

Bit 7 6 5 4 3 2 1 0

Symbol DModWidth

Access

rights

r/w

Table 147. TxDataModWidth register (address 2Fh)

Bit Symbol Description

7 to 0 DModWidth Specifies the length of a pulse for sending data with enabled pulse

modulation. The length is given by the number of carrier clocks + 1.

A pulse can never be longer than from the start of the pulse to the

end of the bit. The starting position of a pulse is given by the setting

of TxDataMod.DPulseType. Note: This register is only used if Miller

modulation (ISO/IEC 14443A PCD) is used. The settings are also

used for the modulation width of start and/or stop symbols.

Table 148. TxDataModWidth bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 90 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

9.10.3 TxSym10BurstLen

If a protocol requires a burst (an unmodulated subcarrier) the length can be defined with

this TxSymBurstLen, the value high or low can be defined by TxSym10BurstCtrl.

Bit 7 6 5 4 3 2 1 0

Symbol RFU Sym1Burst Len RFU Sym0Burst Len

Access

rights

- r/w - r/w

Table 149. TxSym10BurstLen register (address 30h)

Bit Symbol Description

7 RFU -

6 to 4 Sym1BurstLen Specifies the number of bits issued for symbol 1 burst. The 3 bits

encodes a range from 8 to 256 bit:

00h - 8bit

01h - 16bit

02h - 32bit

04h - 48bit

05h - 64bit

06h - 96bit

07h - 128bit

08h - 256bit

3 RFU -

2 to 0 Sym0BurstLen Specifies the number of bits issued for symbol 1 burst. The 3 bits

encodes a range from 8 to 256 bit:

00h - 8bit

01h - 16bit

02h - 32bit

03h - 48bit

04h - 64bit

05h - 96bit

06h - 128bit

07h - 256bit

Table 150. TxSym10BurstLen bits

9.10.4 TxWaitCtrl

Bit 7 6 5 4 3 2 1 0

Symbol TxWaitStart TxWaitEtu TxWait High TxStopBitLength

Access

rights

r/w r/w r/w r/w

Table 151. TxWaitCtrl register (address 31h); reset value: C0h

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 91 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 TxWaitStart If cleared, the TxWait time is starting at the End of the send data

(TX).

If set, the TxWait time is starting at the End of the received data

(RX).

6 TxWaitEtu If cleared, the TxWait time is TxWait × 16/13.56 MHz.

If set, the TxWait time is TxWait × 0.5 / DBFreq (DBFreq is the

frequency of the bit stream as defined by TxDataCon).

5 to 3 TxWait High Bit extension of TxWaitLo. TxWaitCtrl bit 5 is MSB.

2 to 0 TxStopBitLength Defines stop-bits and EGT (= stop-bit + extra guard time EGT) to

be sent:

0h: no stop-bit, no EGT

1h: 1 stop-bit, no EGT

2h: 1 stop-bit + 1 EGT

3h: 1 stop-bit + 2 EGT

4h: 1 stop-bit + 3 EGT

5h: 1 stop-bit + 4 EGT

6h: 1 stop-bit + 5 EGT

7h: 1 stop-bit + 6 EGT

Note: This is only valid for ISO/IEC14443 Type B

Table 152. TXWaitCtrl bits

9.10.5 TxWaitLo

Bit 7 6 5 4 3 2 1 0

Symbol TxWaitLo

Access

rights

r/w

Table 153. TxWaitLo register (address 32h)

Bit Symbol Description

7 to 0 TxWaitLo Defines the minimum time between receive and send or between two

send data streams

Note: TxWait is a 11bit register (additional 3 bits are in the TxWaitCtrl

See also TxWaitEtu and TxWaitStart.

Table 154. TxWaitLo bits

9.11 FrameCon

Bit 7 6 5 4 3 2 1 0

Symbol TxParityEn RxParityEn - - StopSym StartSym

Access

rights

r/w r/w RFU RFU r/w r/w

Table 155. FrameCon register (address 33h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 92 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 TxParityEn If set, a parity bit is calculated and appended to each byte

transmitted.

6 RxParityEn If set, the parity calculation is enabled. The parity is not transferred to

the FIFO.

5 to 4 - RFU

3 to 2 StopSym Defines which symbol is sent as stop-symbol:

•0h: No symbol is sent

•1h: Symbol0 is sent

•2 h symbol1 is sent

•3h Symbol2 is sent

1 to 0 StartSym Defines which symbol is sent as start-symbol:

•0h: No Symbol is sent

•1h: Symbol0 is sent

•2 h: Symbol1 is sent

•3h: Symbol2 is sent

Table 156. FrameCon bits

9.12 Receiver configuration registers

9.12.1 RxSofD

Bit 7 6 5 4 3 2 1 0

Symbol RFU SOF_En SOFDetected RFU SubC_En SubC_Detected SubC_Present

Access

rights

- r/w dy - r/w dy r

Table 157. RxSofD register (address 34h)

Bit Symbol Description

7 to 6 RFU -

5 SOF_En If set and a SOF is detected an RxSOFIRQ is raised.

4 SOF_Detected Shows that a SOF is or was detected. Can be cleared by SW.

3 RFU -

2 SubC_En If set and a subcarrier is detected an RxSOFIRQ is raised.

1 SubC_Detected Shows that a subcarrier is or was detected. Can be cleared by SW.

0 SubC_Present Shows that a subcarrier is currently detected.

Table 158. RxSofD bits

9.12.2 RxCtrl

Bit 7 6 5 4 3 2 1 0

Symbol RxAllowBits RxMultiple RxEOFType EGT_Check EMD_Sup Baudrate

Table 159. RxCtrl register (address 35h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 93 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit 7 6 5 4 3 2 1 0

Access

rights

r/w r/w r/w r/w r/w r/w

Table 159. RxCtrl register (address 35h)...continued

Bit Symbol Description

7 RxAllowBits If set, data is written into FIFO even if CRC is enabled, and no

complete byte has been received.

6 RxMultiple If set, RxMultiple is activated and the receiver will not terminate

automatically (refer Section Section 8.10.3.6.

If set to logic 1, at the end of a received data stream an error byte is

added to the FIFO. The error byte is a copy of the Error register.

5 RxEOFType 0: EOF as defined in the RxEOFSymbolReg is expected.

1: ISO/IEC14443B EOF is expected.

Note: Clearing this bit to 0 and clearing bit 0 and bit 1 in the

RxEOFSymbolReg disables the EOF check.

4 EGT_Check If set to 1, the EGT is checked and if it is too long

a protocol error is set. (This is only valid for ISO/IEC14443 Type B).

3 EMD_Sup Enables the EMD suppression according to ISO/IEC14443. If an error

occurs within the first three bytes, these three bytes are assumed to

be EMD, ignored and the FIFO is reset. A collision is treated as an

error as well If a valid SOF was received, the EMD_Sup is set and a

frame of less than 3 bytes had been received. RX_IRQ is not set in

this EMD error cases. If RxForceCRCWrite is set, the FIFO should not

be read out before three bytes are written into.

2 to 0 Baudrate Defines the baud rate of the receiving signal.

2h: 26 kBd

3h: 52 kBd

4h: 106 kBd

5h: 212 kBd

6h: 424 kBd

7h: 847 kBd

all remaining values are RFU

Table 160. RxCtrl bits

9.12.3 RxWait

Selects internal receiver settings.

Bit 76543210

Symbol RxWaitEtu RxWait

Access

rights

r/w r/w

Table 161. RxWait register (address 36h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 94 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 RXWaitEtu If set to 0, the RxWait time is RxWait × 16/13.56 MHz.

If set to 1, the RxWait time is RxWait × (0.5/DBFreq).

6 to 0 RxWait Defines the time after sending, where every input is ignored.

Table 162. RxWait bits

9.12.4 RxThreshold

Selects minimum threshold level for the bit decoder.

Bit 76543210

Symbol MinLevel MinLevelP

Access

rights

r/w r/w

Table 163. RxThreshold register (address 37h)

Bit Symbol Description

7 to 4 MinLevel Defines the MinLevel of the reception.

Note: The MinLevel should be higher than the noise level in the system.

3 to 0 MinLevelP Defines the MinLevel of the phase shift detector unit.

Table 164. RxThreshold bits

9.12.5 Rcv

Bit 7 6 5 4 3 2 1 0

Symbol Rcv_Rx_single Rx_ADCmode SigInSel RFU CollLevel

Access

rights

r/w r/w r/w - r/w

Table 165. Rcv register (address 38h)

Bit Symbol Description

7 Rcv_Rx_single Single RXP Input Pin Mode;

0: Fully Differential

1: Quasi-Differential

6 Rx_ADCmode Defines the operation mode of the Analog Digital Converter (ADC)

0: normal reception mode for ADC

1: LPCD mode for ADC

5 to 4 SigInSel Defines input for the signal processing unit:

0h - idle

1h - internal analog block (RX)

2h - signal in over envelope (ISO/IEC14443A)

3h - signal in over s3c-generic

3 to 2 RFU -

Table 166. Rcv bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 95 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

1 to 0 CollLevel Defines the strength of a signal to be interpreted as a collision:

0h - Collision has at least 1/8 of signal strength

1h - Collision has at least 1/4 of signal strength

2h - Collision has at least 1/2 of signal strength

3h - Collision detection is switched off

Table 166. Rcv bits...continued

9.12.6 RxAna

This register allows setting the gain (rcv_gain) and high pass corner frequencies

(rcv_hpcf).

Bit 7 6 5 4 3 2 1 0

Symbol VMid_r_sel RFU rcv_hpcf rcv_gain

Access

rights

r/w - r/w r/w

Table 167. RxAna register (address 39h)

Bit Symbol Description

7, 6 VMid_r_sel Factory trim value, needs to be 0.

5, 4 RFU

3, 2 rcv_hpcf The rcv_hpcf [1:0] signals allow 4 different settings of the base band

amplifier high pass cut-off frequency from ~40 kHz to ~300 kHz.

1 to 0 rcv_gain With rcv_gain[1:0] four different gain settings from 30 dB and 60

dB can be configured (differential output voltage/differential input

voltage).

Table 168. RxAna bits

rcv_gain

(Hex.)

rcv_hpcf

(Hex.)

fl (kHz) fU (MHz) gain (dB20) bandwidth

(MHz)

03 00 38 2.3 60 2.3

03 01 79 2.4 59 2.3

03 02 150 2.6 58 2.5

03 03 264 2.9 55 2.6

02 00 41 2.3 51 2.3

02 01 83 2.4 50 2.3

02 02 157 2.6 49 2.4

02 03 272 3.0 41 2.7

01 00 42 2.6 43 2.6

01 01 84 2.7 42 2.6

Table 169. Effect of gain and high-pass corner register settings

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 96 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

rcv_gain

(Hex.)

rcv_hpcf

(Hex.)

fl (kHz) fU (MHz) gain (dB20) bandwidth

(MHz)

01 02 157 2.9 41 2.7

01 03 273 3.3 39 3.0

00 00 43 2.6 35 2.6

00 01 85 2.7 34 2.6

00 02 159 2.9 33 2.7

00 03 276 3.4 30 3.1

Table 169. Effect of gain and high-pass corner register settings...continued

9.13 Clock configuration

9.13.1 SerialSpeed

This register allows setting speed of the RS232 interface. The default speed is set to

115.2 kbit/s. The transmission speed of the interface can be changed by modifying

the entries for BR_T0 and BR_T1. The transfer speed can be calculated by using the

following formulas:

BR_T0 = 0: transfer speed = 27.12 MHz / (BR_T1 + 1)

BR_T0 > 0: transfer speed = 27.12 MHz / (BR_T1 + 33) / 2^(BR_T0 - 1)

The framing is implemented with 1 start bit, 8 data bits and 1 stop bit. A parity bit is not

used. Transfer speeds above 1228.8 kbit/s are not supported.

Bit 7 6 5 4 3 2 1 0

Symbol BR_T0 BR_T1

Access

rights

r/w r/w

Table 170. SerialSpeed register (address3Bh); reset value: 7Ah

Bit Symbol Description

7 to 5 BR_T0 BR_T0 = 0: transfer speed = 27.12 MHz / (BR_T1 + 1)

BR_T0 > 0: transfer speed = 27.12 MHz / (BR_T1 + 33) / 2^(BR_T0 - 1)

4 to 0 BR_T1 BR_T0 = 0: transfer speed = 27.12 MHz / (BR_T1 + 1)

BR_T0 > 0: transfer speed = 27.12 MHz / (BR_T1 + 33) / 2^(BR_T0 - 1)

Table 171. SerialSpeed bits

Transfer speed (kbit/s) SerialSpeed register content (Hex.)

7.2 FA

9.6 EB

14.4 DA

Table 172. RS232 speed settings

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 97 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Transfer speed (kbit/s) SerialSpeed register content (Hex.)

19.2 CB

38.4 AB

57.6 9A

115.2 7A

128.0 74

230.4 5A

460.8 3A

921.6 1C

1228.8 15

Table 172. RS232 speed settings...continued

9.13.2 LFO_Trimm

Bit 7 6 5 4 3 2 1 0

Symbol LFO_trimm

Access

rights

r/w

Table 173. LFO_Trimm register (address 3Ch)

Bit Symbol Description

7 to 0 LFO_trimm Trimm value. Refer to Section Section 8.8.3.

Note: If the trimm value is increased, the frequency of the oscillator

decreases.

Table 174. LFO_Trimm bits

9.13.3 PLL_Ctrl Register

The PLL_Ctrl register implements the control register for the IntegerN PLL. Two stages

exist to create the ClkOut signal from the 27.12 MHz input. In the first stage, the 27.12

MHz input signal is multiplied by the value defined in PLLDiv_FB and divided by two, and

the second stage divides this frequency by the value defined by PLLDIV_Out.

Bit 7 6 5 4 3 2 1 0

Symbol ClkOutSel ClkOut_En PLL_PD PLLDiv_FB

Access

rights

r/w r/w r/w r/w

Table 175. PLL_Ctrl register (address3Dh)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 98 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 4 CLkOutSel •0h - pin CLKOUT is used as I/O

•1h - pin CLKOUT shows the output of the analog PLL

•2h - pin CLKOUT is hold on 0

•3h - pin CLKOUT is hold on 1

•4h - pin CLKOUT shows 27.12 MHz from the crystal

•5h - pin CLKOUT shows 13.56 MHz derived from the crystal

•6h - pin CLKOUT shows 6.78 MHz derived from the crystal

•7h - pin CLKOUT shows 3.39 MHz derived from the crystal

•8h - pin CLKOUT is toggled by the Timer0 overflow

•9h - pin CLKOUT is toggled by the Timer1 overflow

•Ah - pin CLKOUT is toggled by the Timer2 overflow

•Bh - pin CLKOUT is toggled by the Timer3 overflow

•Ch...Fh - RFU

3 ClkOut_En Enables the clock at Pin CLKOUT

2 PLL_PD PLL power down

1-0 PLLDiv_FB PLL feedback divider

Table 176. PLL_Ctrl register bits

Bit 1 Bit 0 Division

0 0 23 (VCO frequency 312 MHz)

0 1 27 (VCO frequency 366 MHz)

1 0 28 (VCO frequency 380 Mhz)

1 1 23 (VCO frequency 312 Mhz)

Table 177. Setting of feedback divider PLLDiv_FB [1:0]

9.13.4 PLLDiv_Out

Bit 7 6 5 4 3 2 1 0

Symbol PLLDiv_Out

Access

rights

r/w

Table 178. PLLDiv_Out register (address 3Eh)

Bit Symbol Description

7 to 0 PLLDiv_Out PLL output divider factor; refer to Section Section 8.8.2.

Table 179. PLLDiv_Out bits

Value Division

0 RFU

1 RFU

Table 180. Setting for the output divider ratio PLLDiv_Out [7:0]

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 99 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value Division

2 RFU

3 RFU

4 RFU

5 RFU

6 RFU

7 RFU

8 8

9 9

10 10

... ...

253 253

254 254

Table 180. Setting for the output divider ratio PLLDiv_Out [7:0]...continued

9.14 Low-power card detection configuration registers

The LPCD registers contain the settings for the low-power card detection. The setting

for LPCD_IMax (6 bits) is done by the two highest bits (bit 7, bit 6) of the registers

LPCD_QMin, LPCD_QMax and LPCD_IMin each.

9.14.1 LPCD_QMin

Bit 7 6 5 4 3 2 1 0

Symbol LPCD_IMax.5 LPCD_IMax.4 LPCD_QMin

Access

rights

r/w r/w r/w

Table 181. LPCD_QMin register (address 3Fh)

Bit Symbol Description

7, 6 LPCD_IMax Defines the highest two bits of the higher border for the LPCD. If the

measurement value of the I channel is higher than LPCD_IMax, an

LPCD interrupt request is indicated by bit IRQ0.LPCDIRQ.

5 to 0 LPCD_QMin Defines the lower border for the LPCD. If the measurement value of

the Q channel is higher than LPCD_QMin, an LPCDinterrupt request

is indicated by bit IRQ0.LPCDIRQ.

Table 182. LPCD_QMin bits

9.14.2 LPCD_QMax

Bit 7 6 5 4 3 2 1 0

Symbol LPCD_IMax.3 LPCD_IMax.2 LPCD_QMax

Table 183. LPCD_QMax register (address 40h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 100 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit 7 6 5 4 3 2 1 0

Access

rights

r/w r/w r/w

Table 183. LPCD_QMax register (address 40h)...continued

Bit Symbol Description

7 LPCD_IMax.3 Defines the bit 3 of the high border for the LPCD. If the

measurement value of the I channel is higher than LPCD IMax, an

LPCD IRQ is raised.

6 LPCD_IMax.2 Defines the bit 2 of the high border for the LPCD. If the

measurement value of the I channel is higher than LPCD IMax, an

LPCD IRQ is raised.

5 to 0 LPCD_QMax Defines the high border for the LPCD. If the measurement value of

the Q channel is higher than LPCD QMax, an LPCD IRQ is raised.

Table 184. LPCD_QMax bits

9.14.3 LPCD_IMin

Bit 7 6 5 4 3 2 1 0

Symbol LPCD_IMax.1 LPCD_IMax.0 LPCD_IMin

Access

rights

r/w r/w r/w

Table 185. LPCD_IMin register (address 41h)

Bit Symbol Description

7 to 6 LPCD_IMax Defines lowest two bits of the higher border for the low-power card

detection (LPCD). If the measurement value of the I channel is higher

than LPCD IMax, an LPCD IRQ is raised.

5 to 0 LPCD_IMin Defines the lower border for the low power card detection. If the

measurement value of the I channel is lower than LPCD IMin, an

LPCD IRQ is raised.

Table 186. LPCD_IMin bits

9.14.4 LPCD_Result_I

Bit 7 6 5 4 3 2 1 0

Symbol RFU- RFU- LPCD_Result_I

Access

rights

- - r

Table 187. LPCD_Result_I register (address 42h)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 101 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 6 RFU -

5 to 0 LPCD_Result_I Shows the result of the last low-power card detection (I-Channel).

Table 188. LPCD_Result_I bits

9.14.5 LPCD_Result_Q

Bit 7 6 5 4 3 2 1 0

Symbol RFU LPCD_

IRQ_Clr

LPCD_Reslult_Q

Access

rights

- r/w r

Table 189. LPCD_Result_Q register (address 43h)

Bit Symbol Description

7 RFU -

6 LPCD_IRQ_Clr If set no LPCD IRQ is raised any more until the next low-power

card detection procedure. Can be used by software to clear the

interrupt source.

5 to 0 LPCD_Result_Q Shows the result of the last low power card detection (Q-

Channel).

Table 190. LPCD_Result_Q bits

9.14.6 LPCD_Options

This register is available on the CLRC66303 only. For silicon versions CLRC66301 and

CLRC66302 this register on address 3AH is RFU.

Bit 7 6 5 4 3 2 1 0

Symbol LPCD_TX_HIGH LPCD_FILTER LPCD_Q_

UNSTABLE

LPCD_I_UNSTABLE

Access

rights

RFU

r/w r/w r r

Table 191. LPCD_Options register (address 3Ah)

Bit Symbol Description

7 to 4 RFU -

3 LPCD_TX_HIGH If set, the TX-driver will be the same as VTVDD during LPCD. This will allow for

a better LPCD detection range (higher transmitter output voltage) at the cost of

a higher current consumption. If this bit is cleared, the output voltage at the TX

drivers will be = TVDD- 0.4V. If this bit is set, the output voltage at the TX drivers

will be = VTVDD.

Table 192. LPCD_Options

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 102 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

2 LPCD_FILTER If set, The LPCD decision is based on the result of a filter which allows to

remove noise from the evaluated signal in I and Q channel. Enabling LPCD_

FILTER allows compensating for noisy conditions at the cost of a longer RF-ON

time required for sampling. The total maximum LPCD sampling time is 4.72us.

1 LPCD_Q_UNSTABLE If bit 2 of this register is set, bit 1 indicates that the Q-channel ADC value was

changing during the LPCD measuring time. Note: Only valid if LPCD_FILTER (bit

2) = 1. This information can be used by the host application for configuration of

e.g. the threshold LPCD_QMax or inverting the TX drivers.

0 LPCD_I_UNSTABLE If bit 2 of this register is set, bit 0 Indicates that the I-channel ADC value was

changing during the LPCD measuring time. Note: Only valid if LPCD_FILTER

(bit2) = 1. This information can be used by the host application for configuration

of e.g. the threshold LPCD_IMax or inverting the TX drivers.

Table 192. LPCD_Options...continued

9.15 Pin configuration

9.15.1 PadEn

Bit 7 6 5 4 3 2 1 0

Symbol SIGIN_

EN / OUT7

CLKOUT_

EN / OUT6

IFSEL1_

EN / OUT5

IFSEL0_

EN / OUT4

TCK_EN /

OUT 3

TMS_EN /

OUT2

TDI_EN /

OUT1

TDO_EN /

OUT0

Access

rights

r/w r/w r/w r/w r/w r/w r/w r/w

Table 193. PadEn register (address 44h)

Bit Symbol Description

7 SIGIN_EN / OUT7 Enables the output functionality on SIGIN (pin 5). The pin is

then used as output.

6 CLKOUT_EN / OUT6 Enables the output functionality of the CLKOUT (pin 22). The

pin is then used as output. The CLKOUT function is switched

off.

5 IFSEL1_EN / OUT5 Enables the output functionality of the IFSEL1 (pin 27). The

pin is then used as output.

4 IFSEL0_EN / OUT4 Enables the output functionality of the IFSEL0 (pin 26). The

pin is then used as output.

3 TCK_EN / OUT3 Enables the output functionality of the TCK (pin 4) of the

boundary scan interface. The pin is then used as output. If

the boundary scan is activated in EEPROM, this bit has no

function.

2 TMS_EN / OUT2 Enables the output functionality of the TMS (pin 2) of the

boundary scan interface. The pin is then used as output. If

the boundary scan is activated in EEPROM, this bit has no

function.

Table 194. PadEn bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 103 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

1 TDI_EN / OUT1 Enables the output functionality of the TDI (pin 1) of the

boundary scan interface. The pin is then used as output. If

the boundary scan is activated in EEPROM, this bit has no

function.

0 TDO_EN / OUT0 Enables the output functionality of the TDO(pin 3) of the

boundary scan interface. The pin is then used as output. If

the boundary scan is activated in EEPROM, this bit has no

function.

Table 194. PadEn bits...continued

9.15.2 PadOut

Bit 7 6 5 4 3 2 1 0

Symbol SIGIN_OUT CLKOUT_OUT IFSEL1_OUT IFSEL0_OUT TCK_OUT TMS_OUT TDI_OUT TDO_OUT

Access

rights

r/w r/w r/w r/w r/w r/w r/w r/w

Table 195. PadOut register (address 45h)

Bit Symbol Description

7 SIGIN_OUT Output buffer of the SIGIN pin

6 CLKOUT_OUT Output buffer of the CLKOUT pin

5 IFSEL1_OUT Output buffer of the IFSEL1 pin

4 IFSEL0_OUT Output buffer of the IFSEL0 pin

3 TCK_OUT Output buffer of the TCK pin

2 TMS_OUT Output buffer of the TMS pin

1 TDI_OUT Output buffer of the TDI pin

0 TDO_OUT Output buffer of the TDO pin

Table 196. PadOut bits

9.15.3 PadIn

Bit 7 6 5 4 3 2 1 0

Symbol SIGIN_IN CLKOUT_IN IFSEL1_IN IFSEL0_IN TCK_IN TMS_IN TDI_IN TDO_IN

Access

rights

r r r r r r r r

Table 197. PadIn register (address 46h)

Bit Symbol Description

7 SIGIN_IN Input buffer of the SIGIN pin

6 CLKOUT_IN Input buffer of the CLKOUT pin

Table 198. PadIn bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 104 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

5 IFSEL1_IN Input buffer of the IFSEL1 pin

4 IFSEL0_IN Input buffer of the IFSEL0 pin

3 TCK_IN Input buffer of the TCK pin

2 TMS_IN Input buffer of the TMS pin

1 TDI_IN Input buffer of the TDI pin

0 TDO_IN Input buffer of the TDO pin

Table 198. PadIn bits...continued

9.15.4 SigOut

Bit 7 6 5 4 3 2 1 0

Symbol Pad

Speed

RFU SigOutSel

Access

rights

r/w - r/w

Table 199. SigOut register (address 47h)

Bit Symbol Description

7 PadSpeed If set, the I/O pins are supporting a fast switching mode.The fast mode

for the I/O’s will increase the peak current consumption of the device,

especially if multiple I/Os are switching at the same time. The power

supply needs to be designed to deliver this peak current.

6 to 4 RFU -

3 to 0 SIGOutSel 0h, 1h - The pin SIGOUT is 3-state

2h - The pin SIGOUT is 0

3h - The pin SIGOUT is 1

4h - The pin SIGOUT shows the TX-envelope

5h - The pin SIGOUT shows the TX-active signal

6h - The pin SIGOUT shows the S3C (generic) signal

7h - The pin SIGOUT shows the RX-envelope

(only valid for ISO/IEC 14443A, 106 kBd)

8h - The pin SIGOUT shows the RX-active signal

9h - The pin SIGOUT shows the RX-bit signal

Table 200. SigOut bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 105 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

9.16 Protocol configuration registers

9.16.1 TxBitMod

Bit 7 6 5 4 3 2 1 0

Symbol TxMSBFirst RFU TxParity

Type

RFU TxStopBitType RFU TxStartBitType TxStartBitEn

Access

rights

r/w - r/w - r/w - r/w r/w

Table 201. TxBitMod register (address 48h)

Bit Symbol Description

7 TxMSBFirst If set, data is interpreted MSB first for data transmission. If cleared,

data is interpreted LSB first.

6 RFU -

5 TxParityType Defines the type of the parity bit. If set to 1, odd parity is calculated,

otherwise even parity is calculated.

4 RFU -

3 TxStopBitType Defines the type of the stop-bit (0b: logic zero / 1b: logic one).

2 RFU -

1 TxStartBitType Defines the type of the start-bit (0b: logic zero / 1b: logic one).

0 TxStartBitEn If set to 1, a start-bit will be sent.

Table 202. TxBitMod bits

9.16.2 TxDataCon

Bit 7 6 5 4 3 2 1 0

Symbol DCodeType DSCFreq DBFreq

Access

rights

r/w r/w r/w

Table 203. TxDataCon (address 4Ah)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 106 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 4 DCodeType Specifies the type of encoding of data to be used:

0h - no special coding

1h - collider datastream is decoded

2h - RFU 3h - RFU

4h - return to zero code - pulse at first position

5h - return to zero code - pulse at 2nd position

6h - return to zero code - pulse at 3rd position

7h - return to zero code - pulse at 4th position

8h - 1 out of 4 coding

9h - 1 out of 256 code (range 0 - 255) [ICODE SLI]

Ah - 1 out of 256 code (range 0 - 255; 00h is encoded with no

modulation, value 256 not used) [ICODE 1]

Bh - 1 out of 256 code (range 0 - 255; 00h is encoded with a pulse on

last position) [ICODE quite value]

Ch- Pulse internal encoded (PIE) [ISO/IEC 18000-3 mode 3/ EPC

Class-1HF]

Dh - RFU

Eh - RFU

Fh - RFU

3 DSCFreq Specifies the subcarrier frequency of the used envelope.

0h - 424 kHz

1h - 848 kHz

Note: This setting is only relevant, if an envelope is used which

involves a subcarrier, e.g. Manchester with subcarrier coding.

2 to 0 DBFreq Specifies the frequency of the bit stream:

0h - RFU

1h - RFU

2h - 26 kHz

3h - 53 kHz

4h - 106 kHz

5h - 212 kHz

6h - 424 kHz

7h - 848 kHz

Table 204. TxDataCon bits

9.16.3 TxDataMod

Bit 7 6 5 4 3 2 1 0

Symbol Frame step DMillerEn DPulseType DInvert DEnvType

Access

rights

r/w r/w r/w r/w r/w

Table 205. TxDataMod register (address 4Bh)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 107 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 Framestep If set to 1, at every start of transmission, each byte of data is sent

in a separate frame. SOF and EOF are appended to the data byte

according to the framing settings. After one byte is transmitted, the

TxEncoder waits for a new start trigger to continue with the next byte

(trigger is generated automatically). If set to 0, transmission is done

in the used way, where after a start trigger all data bytes are sent and

the framing is done for the complete data stream only once.

6 DMillerEn If set, pulse modulation is applied according to modified miller code.

Note: This bit is intended to be set if DPulseType is 1h.

5 to 4 DPulseType Specifies which type of pulse modulation is selected.

0 h - no pulse modulation

1h - pulse starts at beginning of bit

2h - pulse starts at beginning of second bit half

3h - pulse starts at beginning of third bit quarter

Note: If DMillerEn is set, DPulseType must be set to 1h.

3 DInvert If set the envelope of data is inverted.

2 to 0 DEnvType Specifies the type of envelope used for transmission of data packets.

The selected envelope type is applied to the pseudo bit stream.

0h - Direct output

1h - Manchester code

2h - Manchester code with subcarrier

3h - BPSK

4h - RZ (pulse of half bit length at beginning of second half of bit)

5h - RZ (pulse of half bit length at beginning of bit)

6h - RFU

7h - RFU

Table 206. TxDataMod bits

9.16.4 TxSymFreq

Bit 7 6 5 4 3 2 1 0

Symbol S32SCFreq S32BFreq S10SCFreq S10BFreq

Access

rights

r/w r/w r/w r/w

Table 207. TxSymFreq (address 4Ch)

Bit Symbol Description

7 S32SCFreq Specifies the frequency of the subcarrier of symbol2 and symbol3:

0b ... 424 kHz

1b ... 848 kHz

Table 208. TxSymFreq bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 108 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

6 to 4 S32BFreq Specifies the frequency of the bit stream of symbol2 and symbol3:

000b ... RFU

001b ... RFU

010b ... 26 kHz

011b ... 53 kHz

100b ... 106 kHz

101b ... 212 kHz

110b ... 424 kHz

111b ... 848 kHz

3 S10SCFreq Specifies the frequency of the subcarrier of symbol0 and symbol1:

0b ...424 kHz

1b ...848 kHz

2 to 0 S10BFreq Specifies the frequency of the bit stream of symbol0 and symbol1:

000b ... RFU

001b ... RFU

010b ... 26 kHz

011b ... 53 kHz

100b ... 106 kHz

101b ... 212 kHz

110b ... 424 kHz

111b ... 848 kHz

Table 208. TxSymFreq bits...continued

9.16.5 TxSym0

The two Registers TxSym0_H and TxSym0_L create a 16-bit register that contains the

pattern for Symbol0.

Bit 7 6 5 4 3 2 1 0

Symbol Symbol0_H

Access

rights

r/w

Table 209. TxSym0_H (address 4Dh)

Bit Symbol Description

7 to 0 Symbol0_H Higher 8 bits of symbol definition for Symbol0.

Table 210. TxSym0_H bits

Bit 7 6 5 4 3 2 1 0

Symbol Symbol0_L

Access

rights

r/w

Table 211. TxSym0_L (address 4Eh)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 109 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 0 Symbol0_L Lower 8 bits of symbol definition for Symbol0.

Table 212. TxSYM0_L bits

9.16.6 TxSym1

The two Registers TxSym1_H and TxSym1_L create a 16 bit register that contains the

pattern for Symbol1.

Bit 7 6 5 4 3 2 1 0

Symbol Symbol1_H

Access

rights

r/w

Table 213. TxSym1_H (address 4Fh)

Bit Symbol Description

7 to 0 Symbol1_H Higher 8 bits of symbol definition for Symbol1.

Table 214. TxSym1_H bits

Bit 7 6 5 4 3 2 1 0

Symbol Symbol1_L

Access

rights

r/w

Table 215. TxSym1_L (address 50h)

Bit Symbol Description

7 to 0 Symbol1_L Lower 8 bits of symbol definition for Symbol1.

Table 216. TxSym1_L bits

9.16.7 TxSym2

Bit 7 6 5 4 3 2 1 0

Symbol Symbol2

Access

rights

r/w

Table 217. TxSYM2 (address 51h)

Bit Symbol Description

7 to 0 Symbol2 Symbol definition for Symbol2.

Table 218. TxSym2 bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 110 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

9.16.8 TxSym3

Bit 7 6 5 4 3 2 1 0

Symbol Symbol3

Access

rights

r/w

Table 219. TxSym3 (address 52h)

Bit Symbol Description

7 to 0 Symbol3 Symbol definition for Symbol3.

Table 220. TxSym3 bits

9.16.9 TxSym10Len

Bit 7 6 5 4 3 2 1 0

Symbol Sym1Len Sym0Len

Access

rights

r/w r/w

Table 221. TxSym10Len (address 53h)

Bit Symbol Description

7 to 4 Sym1Len Specifies the number of valid bits of the symbol definition of Symbol1.

The range is from 1 bit (0h) to 16 bits (Fh).

3 to 0 Sym0Len Specifies the number of valid bits of the symbol definition of Symbol0.

The range is from 1 bit (0h) to 16 bits (Fh).

Table 222. TxSym10Len bits

9.16.10 TxSym32Len

Bit 7 6 5 4 3 2 1 0

Symbol RFU Sym3Len RFU Sym2Len

Access

rights

- r/w r/w r/w - r/w r/w r/w

Table 223. TxSym32Len (address 54h)

Bit Symbol Description

7 RFU -

6 to 4 Sym3Len Specifies the number of valid bits of the symbol definition of Symbol3.

The range is from 1 bit (0h) to 8 bits (7h).

3 RFU -

Table 224. TxSym32Len bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 111 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

2 to 0 Sym2Len Specifies the number of valid bits of the symbol definition of Symbol2.

The range is from 1 bit (0h) to 8 bits (7h).

Table 224. TxSym32Len bits...continued

9.16.11 TxSym10BurstCtrl

Bit 7 6 5 4 3 2 1 0

Symbol RFU Sym1BurstType Sym1BurstOnly Sym1BurstEn RFU Sym0Burst

Type

Sym0B

urstOnly

Sym0B

urstEn

Access

rights

- r/w r/w r/w - r/w r/w r/w

Table 225. TxSym10BurstCtrl register (address 55h)

Bit Symbol Description

7 RFU -

6 Sym1BurstType Specifies the type of the burst of Symbol1 (logical zero / logical

one).

5 Sym1BurstOnly If set to 1 Symbol1 consists only of a burst and no symbol

pattern.

4 Sym1BurstEn Enables the burst of symbol 1 of the length defined in

TxSym10BurstLen.

3 RFU -

2 Sym0BurstType Specifies the type of the burst of symbol 0 (logical zero / logical

one).

1 Sym0BurstOnly If set to 1, symbol 0 consists only of a burst and no symbol

pattern.

0 Sym0BurstEn Enables the burst of symbol 0 of the length defined in

TxSym10BurstLen.

Table 226. TxSym10BurstCtrl bits

9.16.12 TxSym10Mod Reg

Bit 7 6 5 4 3 2 1 0

Symbol RFU S10MillerEn S10PulseType S10Inv S10EnvType

Access

rights

- r/w r/w r/w r/w

Table 227. TxSym10Mod register (address 56h)

Bit Symbol Description

7 RFU -

Table 228. TxSym10Mod bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 112 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

6 S10MillerEn If set, pulse modulation is applied according to modified miller code.

Note: This bit shall be set only if S10PulseType is set to 1h.

5 to 4 S10PulseType Specifies which type of pulse modulation is selected:

0h - no pulse modulation

1h - pulse starts at beginning of bit

2h - pulse starts at beginning of second bit half

3h - pulse starts at beginning of third bit quarter

3 S10Inv If set. the output of Symbol0 and Symbol1 is inverted.

2 to 0 S10EnvType Specifies the type of envelope used for transmission of Symbol0

and Symbol1. The pseudo bit stream is logically combined with the

selected envelope type.

0h - Direct output

1h - Manchester code

2h - Manchester code with subcarrier

3h - BPKSK

4h - RZ return zero, pulse of half bit length at beginning of second half

of bit

5h - RZ return zero, pulse of half bit length at beginning of second half

of bit

6h - RFU

7h - RFU

Table 228. TxSym10Mod bits...continued

9.16.13 TxSym32Mod

Bit 7 6 5 4 3 2 1 0

Symbol RFU S32MillerEn S32PulseType S32Inv S32EnvType

Access

rights

- r/w r/w r/w r/w

Table 229. TxSym32Mod register (address 57h)

Bit Symbol Description

7 RFU -

6 S32MillerEn If set, pulse modulation is applied according to modified miller code.

Note: This bit shall be set only if S32PulseType is set to 1h.

5 to 4 S32PulseType Specifies which type of pulse modulation is selected:

0h - no pulse modulation

1h - pulse starts at beginning of bit

2h - pulse starts at beginning of second bit half

3h - pulse starts at beginning of third bit quarter

3 S32Inv If set. the output of Symbol2 and Symbol3 is inverted.

Table 230. TxSym32Mod bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 113 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

2 to 0 S32EnvType Specifies the type of envelope used for transmission of symbol 0

and symbol 1. The bit stream is logically combined with the selected

envelope type.

0h - Direct output

1h - Manchester code

2h - Manchester code with subcarrier

3h - BPSK

4h - RZ return zero, pulse of half bit length at beginning of second half

of bit)

5h - RZ return zero, pulse of half bit length at beginning of bit)

6h to 7h RFU

Table 230. TxSym32Mod bits...continued

9.17 Receiver configuration

9.17.1 RxBitMod

Bit 7 6 5 4 3 2 1 0

Symbol RFU RFU RxStopOnInvPar RxStopOnLength RxMSBFirst RxStopBitEn RxParityType RFU

Access

rights

- - r/w r/w r/w r/w r/w -

Table 231. RxBitMod (address 58h)

Bit Symbol Description

7 to 6 RFU -

5 RxStopOnInvPar If set to 1, inverse parity bit is a stop condition.

4 RxStopOnLength If set to 1, data reception stops when the number of received

bytes reach the defined frame length. The value for the

frame length is taken from the first data-byte received.

3 RxMSBFirst If set to 1, data bytes are interpreted MSB first for data

reception, which means data is converted at the CLCoPro

interface. If this bit is set to 0, data is interpreted LSB first.

2 RxStopBitEn If set, a stop-bit is expected and will be checked and

extracted from data stream. Additionally on detection of

a stop-bit a reset signal for the demodulator is generator

to enable a resynchronization of the demodulator. If the

expected stop-bit is incorrect, a frame error flag is set and

the reception is aborted.

Note: A stop bit is always considered to be a logic 1

1 RxParityType Defines which type of the parity-bit is calculated:

If cleared: Even parity

If set: Odd parity

0 RFU -

Table 232. RxBitMod bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 114 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

9.17.2 RxEofSym

Bit 7 6 5 4 3 2 1 0

Symbol RxEOFSymbol

Access

rights

r/w

Table 233. RxEofSym (address 59h)

Bit Symbol Description

7 to 0 RxEOF

Symbol

This value defines the pattern of the EOF symbol with a maximum

length of 4 bit. Every tuple of 2 bits of the RxEOFSymbol encodes

one bit of the EOF symbol. A 00 tuple closes the symbol. In this way

symbols with less than 4 bits can be defined, starting with the bit0

and bit1. The leftmost active symbol pattern is processed first, which

means the pattern is expected first. If the bit0 and bit1 are both zero,

the EOF symbol is disabled. The following mapping is defined:

0h - no symbol bit

1h - zero value

2h - one value

3h - collision

Example:

1Dh: Zero-Collision-Zero

E8h: No symbol because two LSBits are zero

Table 234. RxEOFSym bits

9.17.3 RxSyncValH

Bit 7 6 5 4 3 2 1 0

Symbol RxSyncValH

Access

rights

r/w

Table 235. RxSyncValH register (address5Ah)

Bit Symbol Description

7 to 0 RxSyncValH Defines the high byte of the Start Of Frame (SOF) pattern, which must

be in front of the receiving data.

Table 236. RxSyncValH bits

9.17.4 RxSyncValL

Bit 7 6 5 4 3 2 1 0

Symbol RxSyncValL

Access

rights

r/w

Table 237. RxSyncValL register (address 5Bh)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 115 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

7 to 0 RxSyncValL Defines the low byte of the Start Of Frame (SOF) Pattern, which must

be in front of the receiving data.

Table 238. RxSyncValL bits

9.17.5 RxSyncMod

Bit 7 6 5 4 3 2 1 0

Symbol SyncLen SyncNegEdge LastSyncHalf SyncType

Access

rights

r/w r/w r/w r/w

Table 239. RxSyncMode register (address 5Ch)

Bit Symbol Description

7 to 4 SyncLen Defines how many Bits of registers RxSyncValH and RxSyncValL are

valid. For ISO/IEC 14443B set to 0.

3 SyncNegEdge Is used for SOF with no correlation peak. The first negative edge of

the correlation is used for defining the bit grid.

2 LastSyncHalf The last Bit of the Sync mode has only half of the length compared to

all other bits. (ISO/IEC 18000-3 mode 3/ EPC Class-1HF).

1 to 0 SyncType 0: all 16 bits of SyncVal are interpreted as burst.

1: a nibble of bits is interpreted as one bit in following way:

{data, coll} data = zero or one; coll = 1 means a collision on this bit.

Note: if Coll = 1 the value of data is ignored.

2: the synchronization is done at every start bit of each byte (type B)

3: RFU

Table 240. RxSyncMod bits

9.17.6 RxMod

Bit 7 6 5 4 3 2 1 0

Symbol RFU RFU PreFilter RectFilter SyncHigh CorrInv FSK BPSK

Access

rights

- - r/w r/w r/w r/w r/w r/w

Table 241. RxMod register (address 5Dh)

Bit Symbol Description

7 to 6 - RFU

5 PreFilter If set 4 samples are combined to one data. (average).

4 RectFilter If set, the ADC-values are changed to a more rectangular wave

shape.

3 SyncHigh Defines if the bit grid is fixed at maximum (1) or at minimum (0) value

of the correlation.

Table 242. RxMod bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 116 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Bit Symbol Description

2 CorrInv Defines a logical for Manchester coding:

0: subcarrier / no subcarrier.

1 FSK If set to 1, the demodulation scheme is set to FSK.

0 BPSK If set to 1, the modulation scheme is BPSK.

Table 242. RxMod bits...continued

9.17.7 RxCorr

Bit 7 6 5 4 3 2 1 0

Symbol CorrFreq CorrSpeed CorrLen RFU

Access

rights

r/w r/w r/w r/w r/w -

Table 243. RxCorr register (address 5Eh)

Bit Symbol Description

7, 6 CorrFreq 0h - 212 kHz

1h - 424 kHz

2h - 848 kHz

3h - 848 kHz

5, 4 CorrSpeed Defines the number of clocks used for one correlation.

0h - ISO/IEC 14443

1h - ICODE 53 kBd, FeliCa 424 kBd

2h - ICODE 26 kBd, FeliCa 212 kBd

3h - RFU

3 CorrLen Defines the length of the correlation data. (64 or 32 values).

If set the lengths of the correlation data is 32 values. (ISO/IEC

18000-3 mode 3/ EPC Class-1HF, 2 Pulse Manchester 848 kHz

subcarrier).

2 to 0 RFU -

Table 244. RxCorr bits

9.17.8 FabCali

Bit 7 6 5 4 3 2 1 0

Symbol FabCali

Access

rights

r/w

Table 245. FabCali register (address 5Fh)

Bit Symbol Description

7 to 0 FabCali Fabrication calibration of the receiver.

NOTE: do not change boot value.

Table 246. FabCali bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 117 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

9.18 Version register

9.18.1 Version

Bit 7 6 5 4 3 2 1 0

Symbol Version SubVersion

Access

rights

r r

Table 247. Version register (address 7Fh)

Bit Symbol Description

7 to 4 Version Includes the version of the CLRC663 silicon.

CLRC66301: 0x1

CLRC66302: 0x1

CLRC66303: 0x1

3 to 0 SubVersion Includes the subversion of the CLRC663 silicon.

CLRC66301: 0x8

CLRC66302: 0x8 -No difference of the silicon between versions

CLRC66301 and CLRC66302

CLRC66303: 0xA

LPCD_OPTIONS register had been added compared to earlier

version of the CLRC663. Default configuration for LoadProtocol

updated for improved performance. User EEPROM initialized with

data. Transmitter driver allows higher ITVDD than lower SubVersions.

Table 248. Version bits

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 118 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

10 Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol Parameter Conditions Min Max Unit

VDD supply voltage -0.5 +6.0 V

VDD(PVDD) PVDD supply voltage -0.5 +6.0 V

VDD(TVDD) TVDD supply voltage -0.5 +6.0 V

CLRC66301, CLRC66302 - 250 mAIDD(TVDD) TVDD supply current

CLRC66303 - 500 mA

Vi(RXP) input voltage on pin RXP -0.5 +2.0 V

Vi(RXN) input voltage on pin RXN -0.5 +2.0 V

Ptot total power dissipation per package - 1125 mW

human body model (HBM)[1] ;

1500 Ω, 100 pF

-2000 2000 VVESD electrostatic discharge voltage

charge device model (CDM)[2] -500 500 V

Tj(max) maximum junction

temperature

- +150 °C

Tstg storage temperature no supply voltage applied -55 +150 °C

Table 249. Limiting values

[1] According to ANSI/ESDA/JEDEC JS-001.

[2] According to ANSI/ESDA/JEDEC JS-002.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 119 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

11 Recommended operating conditions

Exposure of the device to other conditions than specified in the Recommended Operating

Conditions section for extended periods may affect device reliability.

Electrical parameters (minimum, typical and maximum) of the device are guaranteed only

when it is used within the recommended operating conditions.

Symbol Parameter Conditions Min Typ Max Unit

VDD supply voltage 3.0 5.0 5.5 V

VDD(TVDD) TVDD supply voltage [1] 3.0 5.0 5.5 V

VDD(PVDD) PVDD supply voltage all host interfaces 3.0 5.0 5.5 V

Tj(max) maximum junction

temperature

- - - +125 °C

Tamb operating ambient

temperature

in still air with exposed pin soldered on a 4

layer JEDEC PCB

-40 +25 +105 °C

Tstg storage temperature no supply voltage applied, relative humidity

45...75%

-45 +25 +125 °C

Table 250. Operating conditions CLRC66301, CLRC66302

[1] VDD(PVDD) must always be the same or lower than VDD.

Symbol Parameter Conditions Min Typ Max Unit

VDD supply voltage 2.5 5.0 5.5 V

VDD(TVDD) TVDD supply voltage [1] 2.5 5.0 5.5 V

all host interfaces except I2C interface 2.5 5.0 5.5 VVDD(PVDD) PVDD supply voltage

all host interfaces incl. I2C interface 3.0 5.0 5.5 V

Tj(max) maximum junction

temperature

- - - +125 °C

HVQFN32 package, in still air with exposed

pin soldered on a 4 layer JEDEC PCB

-40 +25 +105 °CTamb operating ambient

temperature

VFBGA36 package, in still air with exposed

pin soldered on a 4 layer JEDEC PCB

-40 +25 +85 °C

Tstg storage temperature no supply voltage applied, relative humidity

45...75%

-45 +25 +125 °C

Table 251. Operating conditions CLRC66303

[1] VDD(PVDD) must always be the same or lower than VDD.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 120 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

12 Thermal characteristics

12.1 Thermal characteristics HVQFN32

Symbol Parameter Conditions Package Typ Unit

Rth(j-a) thermal resistance from junction to

ambient

in still air with exposed pin soldered on a 4

layer JEDEC PCB

HVQFN32 40 K/W

Table 252. Thermal characteristics

12.2 Thermal characteristics VFBGA36

Symbol Parameter Conditions Package Typ Unit

Rth(j-a) thermal resistance from junction to

ambient

in still air with exposed pin soldered on a 4

layer JEDEC PCB

VFBGA36 65 K/W

Table 253. Thermal characteristics

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 121 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

13 Characteristics

Symbol Parameter Conditions Min Typ Max Unit

Current consumption

IDD = AVDD+DVDD; modem

on (transmitter and

receiver are switched on)

- 17 20 mAIDD supply current

IDD = AVDD+DVDD; modem

off (transmitter and

receiver are switched off)

- 0.45 0.5 mA

IDD(PVDD) PVDD supply current no load on digital pins,

leakage current only

- 0.5 5 μA

CLRC66301HN,

CLRC66302HN

- 100 250 mAIDD(TVDD) TVDD supply current

CLRC66303HN - 250 350 mA

All OUTx pins floating

ambient temp = +25 °C - 40 400 nA

ambient temp = -40°C...

+85°C

- 1.5 2.1 μA

Ipd power-down current

CLRC66303: ambient temp

= +105 °C

- 3.5 5.2 μA

Istby standby current All OUTx pins floating

ambient temp = 25 °C,

IVDD+ITVDD+ IPVDD

- 3 6

ambient temp = -40°C...

+105°C, Istby = IVDD+ITVDD+

IPVDD

- 5.25 26

μA

All OUTx pins floatingILPCD(sleep) LPCD sleep current

LFO active, no RF field on,

ambient temp = 25 °C

[1] - 3.3 6.3 μA

All OUTx pins floating,

TxLoad = 50 ohms.

LPCD_FILTER = 0; Rfon

duration = 10 us, RF-off

duration 300ms; VTVDD =

3.0V; Tamb = 25°C; ILPCD =

IVDD+ITVDD+ IPVDD

LPCD_TX_HIGH = 0, - 12 -

ILPCD(average)

LPCD average current

LPCD_TX_HIGH = 1 - 23 -

μA

tRFON RF-on time during LPCD LPCD_TX_HIGH = 0;

TVDD=5.0 V

T=25°C;

- 10 - μs

LPCD_TX_HIGH = 1;

TVDD=5.0 V; T=25°C

- 50 - μs

Buffer capacitors on AVDD,DVDD

Table 254. Characteristics

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 122 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Symbol Parameter Conditions Min Typ Max Unit

CLexternal buffer capacitor AVDD 220 470 - nF

CLexternal buffer capacitor DVDD 220 470 - nF

I/O pin characteristics SIGIN/OUT7, SIGOUT, CLKOUT/OUT6,

IFSEL0/OUT4, IFSEL1/OUT5, TCK/OUT3, TMS/OUT2, TDI/

OUT1, TDO/OUT0, IRQ, IF0, IF1, IF2, SCL2, SDA2

ILI input leakage current output disabled 0.0 50 500 nA

VIL low-level input voltage -0.5 - 0.3 x VDD(PVDD) V

VIH high-level input voltage 0.7 x

VDD(PVDD)

VDD(PVDD) + 0.5 V

VOL low-level output voltage 0.0 0.0 0.4 V

VOH high-level output voltage If pins are used as output

OUTx, IOH = 4 mA driving

current for each pin

VDD(PVDD)-0.4 VDD(PVDD)

VDD(PVDD) V

Ciinput capacitance 0.0 2.5 4.5 pF

Pin characteristics PDOWN

VIL low-level input voltage 0.0 0.0 0.4 V

VIH high-level input voltage 0.6 x VPVDD VDD(PVDD)

VDD(PVDD) V

Pull-up resistance for TCK, TMS, TDI, IF2

Rpu pull-up resistance 50 72 120 KΩ

Pin characteristics AUX 1, AUX 2

Vooutput voltage 0.0 - 1.8 V

CLload capacitance 0.0 - 400 pF

Pin characteristics RXP, RXN

Vi(p) input voltage 0 1.65 1.8 V

Ciinput capacitance 2 3.5 5 pF

Vmod(pp) modulation voltage Vmod(pp) = Vi(pp)(max) - Vi(pp)

(min)

- 2.5 - mV

Pins TX1 and TX2

Vooutput voltage Vss(TVSS) - VDD(TVDD) V

CLRC66301, CLRC66302:

T=25°C, VDD(TVDD) = 5.0V

- 1.5 - ΩRooutput resistance

CLRC66303: T=25°C,

VDD(TVDD) = 5.0V

- 1.2 - Ω

Clock frequency Pin CLKOUT

fclk clock frequency configured to 27.12 MHz - 27.12 - MHz

δclk clock duty cycle - 50 - %

Crystal connection XTAL1, XTAL2

Vo(p-p) peak-to-peak output

voltage

pin XTAL1 - 1.0 - V

Table 254. Characteristics...continued

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 123 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Symbol Parameter Conditions Min Typ Max Unit

Viinput voltage pin XTAL1 0.0 - 1.8 V

Ciinput capacitance pin XTAL1 - 3 - pF

Crystal requirements

fxtal crystal frequency ISO/IEC14443 compliancy 27.12-14kHz 27.12 27.12+14kHz MHz

ESR equivalent series

resistance

- 50 100 Ω

CLload capacitance - 10 - pF

Pxtal crystal power dissipation - 50 100 μW

Input characteristics I/O Pin Characteristics IF3-SDA in I2C configuration

ILI input leakage current output disabled - 2 100 nA

VIL LOW-level input voltage -0.5 - +0.3 VDD(PVDD) V

VIH HIGH-level input voltage 0.7 VDD(PVDD) - VDD(PVDD) + 0.5 V

VOL LOW-level output voltage IOL = 3 mA - - 0.3 V

VOL = 0.4 V; Standard

mode, Fast mode

4 - - mAIOL LOW-level output current

VOL = 0.6 V; Standard

mode, Fast mode

6 - - mA

Standard mode, Fast

mode, CL < 400 pF

- - 250 nstf(o) output fall time

Fast mode +; CL < 550 pF - - 120 ns

tSP pulse width of spikes that

must be suppressed by

the input filter

0 - 50 ns

Ciinput capacitance - 3.5 5 pF

Standard mode - - 400 pFCLload capacitance

Fast mode - - 550 pF

tEER EEPROM data retention

time

Tamb = +55 °C 10 - - year

NEEC EEPROM endurance

(number of programming

cycles)

under all operating

conditions

5 x 105- - cycle

Table 254. Characteristics...continued

[1] Ipd is the total current for all supplies.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 124 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

001aak012

VMID

0 V

Vmod

Vi(p-p)(max) Vi(p-p)(min)

13.56 MHz

carrier

Figure 34. Pin RX input voltage

13.1 Timing characteristics

Symbol Parameter Conditions Min Typ Max Unit

tSCKL SCK LOW time 50 - - ns

tSCKH SCK HIGH time 50 - - ns

th(SCKH-D) SCK HIGH to data input hold

time

SCK to changing MOSI 25 - - ns

tsu(D-SCKH) data input to SCK HIGH set-

up time

changing MOSI to SCK 25 - - ns

th(SCKL-Q) SCK LOW to data output

hold time

SCK to changing MISO - - 25 ns

t(SCKL-NSSH) SCK LOW to NSS HIGH time 0 - - ns

tNSSH NSS HIGH time before communication 50 - - ns

Table 255. SPI timing characteristics

Remark: To send more bytes in one data stream, the NSS signal must be LOW during

the send process. To send more than one data stream, the NSS signal must be HIGH

between each data stream.

Fast mode Fast mode

Plus

Symbol Parameter Conditions

Min Max Min Max

Unit

fSCL SCL clock frequency 0 400 0 1000 kHz

tHD;STA hold time (repeated) START condition after this period, the first

clock pulse is generated

600 - 260 - ns

tSU;STA set-up time for a repeated START

condition

600 - 260 - ns

tSU;STO set-up time for STOP condition 600 - 260 - ns

tLOW LOW period of the SCL clock 1300 - 500 - ns

tHIGH HIGH period of the SCL clock 600 - 260 - ns

tHD;DAT data hold time 0 900 - 450 ns

tSU;DAT data set-up time 100 - - - ns

Table 256. I2C-bus timing in fast mode and fast mode plus

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 125 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Fast mode Fast mode

Plus

Symbol Parameter Conditions

Min Max Min Max

Unit

trrise time SCL signal 20 300 - 120 ns

tffall time SCL signal 20 300 - 120 ns

trrise time SDA and SCL signals 20 300 - 120 ns

tffall time SDA and SCL signals 20 300 - 120 ns

tBUF bus free time between a STOP and

START condition

1.3 - 0.5 - μs

Table 256. I2C-bus timing in fast mode and fast mode plus...continued

001aaj635

SDA

SCL

tLOW tf

tSP tr

tHD;STA tHD;DAT

tHD;STA

trtHIGH

tSU;DAT

S Sr P S

tSU;STA

tSU;STO

tBUF

Figure 35. Timing for fast and standard mode devices on the I2C-bus

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 126 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

14 Application information

A typical application diagram using a complementary antenna connection to the

CLRC663 is shown in the following figure.

The antenna tuning and RF part matching is described in the application note [1] and [2].

001aam269

VDD PVDD

MICRO-

PROCESSOR

host

interface

TVDD

XTAL1 XTAL2

RXN

VMID

TX1

TVSS

TX2

8 25 18

VSS

33 20

28-31

PDOWN

IRQ

DVDD

AVDD

12 RXP

READER IC

L0 C1 Ra

CRXN

CRXP

Cvmid

27.12 MHz

antenna

Lant

Figure 36. Typical application antenna circuit diagram

14.1 Antenna design description

The matching circuit for the antenna consists of an EMC low pass filter (L0 and C0), a

matching circuitry (C1 and C2), and a receiving circuits (R1 = R3, R2 = R4, C3 = C5

and C4 = C6;), and the antenna itself. The receiving circuit component values need to

be designed for operation with the CLRC663. A re-use of dedicated antenna designs

done for other products without adaptation of component values will result in degraded

performance.

14.1.1 EMC low pass filter

The MIFARE product-based system operates at a frequency of 13.56 MHz. This

frequency is derived from a quartz oscillator to clock the CLRC663 and is also the

basis for driving the antenna with the 13.56 MHz energy carrier. This will not only

cause emitted power at 13.56 MHz but will also emit power at higher harmonics. The

international EMC regulations define the amplitude of the emitted power in a broad

frequency range. Thus, an appropriate filtering of the output signal is necessary to fulfill

these regulations.

Remark: The PCB layout has a major influence on the overall performance of the filter.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 127 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

14.1.2 Antenna matching

Due to the impedance transformation of the given low pass filter, the antenna coil has to

be matched to a certain impedance. The matching elements C1 and C2 can be estimated

and have to be fine-tuned depending on the design of the antenna coil.

The correct impedance matching is important to provide the optimum performance.

The overall quality factor has to be considered to guarantee a proper ISO/IEC 14443

communication scheme. Environmental influences have to be considered as well as

common EMC design rules.

For details, refer to the NXP application notes.

14.1.3 Receiving circuit

The internal receiving concept of the CLRC663 makes use both side-bands of the

subcarrier load modulation of the card response via a differential receiving concept (RXP,

RXN). No external filtering is required.

It is recommended using the internally generated VMID potential as the input potential

of pin RX. This DC voltage level of VMID has to be coupled to the Rx-pins via R2 and

R4. To provide a stable DC reference voltage capacitances C4, C6 has to be connected

between VMID and ground. Refer to Figure 36.

Considering the (AC) voltage limits at the Rx-pins the AC voltage divider of R1 + C3 and

R2 as well as R3 + C5 and R4 has to be designed. Depending on the antenna coil design

and the impedance matching, the voltage at the antenna coil varies from antenna design

to antenna design. Therefore the recommended way to design the receiving circuit is to

use the given values for R1(= R3), R2 (= R4), and C3 (= C5) from the above mentioned

application note, and adjust the voltage at the RX-pins by varying R1(= R3) within the

given limits.

Remark: R2 and R4 are AC-wise connected to ground (via C4 and C6).

14.1.4 Antenna coil

The precise calculation of the antenna coils’ inductance is not practicable but the

inductance can be estimated using the following formula. We recommend designing an

antenna either with a circular or rectangular shape.

(4)

•I1 - Length in cm of one turn of the conductor loop

•D1 - Diameter of the wire or width of the PCB conductor respectively

•K - Antenna shape factor (K = 1.07 for circular antennas and K = 1.47 for square

antennas)

•L1 - Inductance in nH

•N1 - Number of turns

•Ln: Natural logarithm function

The actual values of the antenna inductance, resistance, and capacitance at 13.56

MHz depend on various parameters such as:

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 128 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

•antenna construction (Type of PCB)

•thickness of conductor

•distance between the windings

•shielding layer

•metal or ferrite in the near environment

Therefore a measurement of those parameters under real life conditions, or at least a

rough measurement and a tuning procedure are highly recommended to guarantee a

reasonable performance. For details, refer to the above mentioned application notes.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 129 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

15 Package outline

15.1 Package outline HVQFN32

0.5 1

A1 Eh

UNIT y e

0.2

REFERENCES

OUTLINE

VERSION

EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

mm 5.1

4.9

3.25

2.95

5.1

4.9

3.25

2.95

3.5

0.30

0.18

0.05

0.00 0.05 0.1

DIMENSIONS (mm are the original dimensions)

SOT617-1 MO-220 - - - - - -

0.5

0.3

0.1

0.05

0 2.5 5 mm

scale

SOT617-1

HVQFN32: plastic thermal enhanced very thin quad flat package; no leads;

32 terminals; body 5 x 5 x 0.85 mm

A(1)

max.

detail X

y1 C

9 16

32 25

B A

terminal 1

index area

terminal 1

index area

01-08-08

02-10-18

1/2 e

1/2 e A C

v M

w M

(1)

Note

1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.

(1)

Figure 37. Package outline SOT-617-1 (HVQFN32)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 130 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

15.2 Package outline and PCB design information VFBGA36

Figure 38. VFBGA36 Package outline

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 131 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Figure 39. VFBGA36 Package outline notes

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 132 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Figure 40. VFBGA36 PCB design: Solder mask opening pattern

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 133 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Figure 41. VFBGA36 PCB design: I/O pads and solderable area

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 134 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Figure 42. VFBGA36 PCB design: Solder paste stencil

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 135 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

16 Marking

16.1 Marking HVQFN32

Type number Marking code

CLRC66303HN

Line A 66303

Line B Diffusion Batch ID, " ", Assembly sequence ID

Line C contains information about diffusion center

(“Z” = SSMC), assembly center (“S” = ATKH),

RHF classification (“D” = dark green), date

code (“718” = YWW) and maturity level

(“X” = engineering samples, “Y” = customer

qualification samples, “1“ = released product)

Table 257. Marking code

aaa-035755

A : 5

B : 5

C : 7

0 5

Figure 43. HVQFN32 Package marking

16.2 Marking VFBGA36

Type number Marking code

CLRC663A0EV

Line A 6633

Line B Diffusion Batch ID, Assembly sequence ID

Line C S, year, week, week, " "

Table 258. Marking code: VFBGA36

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 136 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

aaa-035760

A : 4

B : 5

C : 5

0 5

Figure 44. VFBGA36 Package marking

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 137 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

17 Handling information

CAUTION

This device is sensitive to ElectroStatic Discharge (ESD). Observe

precautions for handling electrostatic sensitive devices.

Such precautions are described in the ANSI/ESD S20.20, IEC/ST 61340-5,

JESD625-A or equivalent standards.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 138 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

18 Packing information

Moisture Sensitivity Level (MSL) evaluation has been performed according to SNW-

FQ-225B rev.04/07/07 (JEDEC J-STD-020C).

An MSL corresponds to a certain out-of-bag time (or floor life). If semiconductor

packages are removed from their sealed dry-bags and not soldered within their out-of-

bag time, they must be baked prior to reflow soldering, in order to remove any moisture

that might have soaked into the package.

For MSL3:

168h out-of-pack floor life at maximum ambient temperature, conditions < 30°C / 60 %

RH.

For MSL2:

•1 year out-of-pack floor life at maximum ambient temperature, conditions < 30°C / 60 %

RH.

For MSL1:

•No out-of-pack floor live spec. required. Conditions: <30°C / 85 % RH.

001aaj740

strap 46 mm from corner

tray

chamfer

PIN 1

chamfer

PIN 1

printed plano box

ESD warning preprinted

barcode label (permanent)

barcode label (peel-off)

QA seal

Hyatt patent preprinted

The straps around the package of

stacked trays inside the plano-box

have sufficient pre-tension to avoid

loosening of the trays.

In the traystack (2 trays)

only ONE tray type* allowed

*one supplier and one revision number.

Figure 45. Packing information 1 tray

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 139 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

aaa-004952

PQ-label (permanent) bag

strap 46 mm from the corner

dry-agent

ESD warning preprinted

PQ-label (permanent)

dry-pack ID preprinted

strap

QA seal

relative humidity indicator

tray

preprinted:

recycling symbol

moisture caution label

ESD warning

manufacturer bag info

chamfer

printed plano box

PIN 1

PLCC52

Figure 46. Packing information 5 tray

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 140 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

1.55

3.00

(0.30)

16.60±0.08+7°/S SQ.

1.20

0.56

3.32

(14.40+5°/S SQ.)

(1.45)

1.10

2.50

(0.64)

0.35

aaa-004949

AL AL AM AM

section BC-BC

scale 4:1

vacuum cell

section BD-BD

scale 4:1

section BA-BA

scale 4:1

detail AC

scale 20:1 section AJ-AJ

scale 2:1

section AR-AR

scale 2:1

section AL-AL

scale 5:1

section AK-AK

scale 5:1

section AM-AM

scale 4:1

section AN-AN

scale 4:1

end lock side lock

12.80-5°/S SQ.

14.20±0.08+10°/S SQ.

13.85±0.08+12°/S SQ.

BA C

0.50

BA C

0.50

Figure 47. Tray details

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 141 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

aaa-004950

tape

guard band

circular sprocket holes

opposite the label side of reel

cover tape

carrier tape

enlongated

circular

enlongated

PIN1 has to be

in quadrant 1

QA seal

preprinted ESD warning

PQ-label

dry-pack ID preprinted

(permanent)

product orientation

in carrier tape

product orientation ONLY for turned

products with 12nc ending 128

HOW TO SECURE LEADER END TO THE GUARD BAND,

HOW TO SECURE GUARD BAND

unreeling direction

(see: HOW TO SECURE)

PIN1

PIN1 PIN1

BGA

bare die BGA

bare die for SOT505-2

ending 125

for SOT765

ending 125

PIN1 PIN1 PIN1

PIN1 PIN1

QFP QFP

PLCCSO SO

1 2

3 4

(HV)QFN

(HV)SON

(H)BCC

(HV)QFN

(HV)SON

(H)BCC

1 2

3 4

see: ASSY REEL + LABELS

ASSY REEL + LABELS

label side embossed

ESD logo

embossed

ESD logo

tape

printed plano-box

Ø 330x12/16/24/32 (hub 7'')

Ø 330x16/24/32/44 (hub 4'')

Ø 330x44 (hub 6'')

Ø 180x12/16/24

tapeslot

label side

trailer

leader

leader : lenght of trailer shall be 400 mm min.

and covered with cover tape

circular sprocket hole side

guard band

trailer : lenght of trailer shall be 160 mm min.

and covered with cover tape

tape

(with pull tabs on both ends)

guard band

lape double-backed

onto itself on both ends

Figure 48. Packing information Reel

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 142 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Notes

This page intentionally left blank

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 143 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

19 Appendix

19.1 LoadProtocol command register initialization

The RF configuration is loaded with the command Load Protocol. The tables below

show the register configuration as performed by this command for each of the protocols.

Antenna specific configurations are not covered by this register settings.

The CLRC66301 and CLRC66302 is not initialized for any antenna configuration. For this

product the antenna configuration needs to be done by firmware.

The CLRC66303 antenna configuration in the user EEPROM is described in the chapter

Section 19.2.

Value for register Value (hex)

TxBitMod 20

RFU 00

TxDataCon 04

TxDataMod 50

TxSymFreq 40

TxSym0H 00

TxSym0L 00

TxSym1H 00

TxSym1L 00

TxSym2 00

TxSym3 00

TxSym10Len 00

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 50

RxBitMod 02

RxEofSym 00

RxSyncValH 00

RxSyncValL 01

RxSyncMod 00

RxMod 08

RxCorr 80

FabCal B2

Table 259. ISO/IEC14443-A 106 / MIFARE Classic (Protocol Number 00)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 144 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

TxBitMod 20

RFU 00

TxDataCon 05

TxDataMod 50

TxSymFreq 50

TxSym0H 00

TxSym0L 00

TxSym1H 00

TxSym1L 00

TxSym2 00

TxSym3 00

TxSym10Len 00

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 50

RxBitMod 22

RxEofSym 00

RxSyncValH 00

RxSyncValL 00

RxSyncMod 00

RxMod 0D

RxCorr 80

FabCal B2

Table 260. ISO/IEC14443-A 212/ MIFARE Classic (Protocol Number 01)

Value for register Value (hex)

TxBitMod 20

RFU 00

TxDataCon 06

TxDataMod 50

TxSymFreq 60

TxSym0H 00

TxSym0L 00

TxSym1H 00

TxSym1L 00

Table 261. ISO/IEC14443-A 424/ MIFARE Classic (Protocol Number 02)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 145 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

TxSym2 00

TxSym3 00

TxSym10Len 00

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 50

RxBitMod 22

RxEofSym 00

RxSyncValH 00

RxSyncValL 00

RxSyncMod 00

RxMod 0D

RxCorr 80

FabCal B2

Table 261. ISO/IEC14443-A 424/ MIFARE Classic (Protocol Number 02)...continued

Value for register Value (hex)

TxBitMod 20

RFU 00

TxDataCon 07

TxDataMod 50

TxSymFreq 70

TxSym0H 00

TxSym0L 00

TxSym1H 00

TxSym1L 00

TxSym2 00

TxSym3 00

TxSym10Len 00

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 50

RxBitMod 22

RxEofSym 00

Table 262. ISO/IEC14443-A 848/ MIFARE Classic (Protocol Number 03)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 146 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

RxSyncValH 00

RxSyncValL 00

RxSyncMod 00

RxMod 0D

RxCorr 80

FabCal B2

Table 262. ISO/IEC14443-A 848/ MIFARE Classic (Protocol Number 03)...continued

Value for register Value (hex)

TxBitMod 09

RFU 00

TxDataCon 04

TxDataMod 08

TxSymFreq 04

TxSym0H 00

TxSym0L 03

TxSym1H 00

TxSym1L 01

TxSym2 00

TxSym3 00

TxSym10Len AB

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 08

TxSym32Mod 00

RxBitMod 04

RxEofSym 00

RxSyncValH 00

RxSyncValL 00

RxSyncMod 02

CLRC66301, CLRC66302: 1DRxMod

CLRC663003: 0D

RxCorr 80

FabCal B2

Table 263. ISO/IEC14443-B 106 Classic (Protocol Number 04)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 147 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

TxBitMod 09

RFU 00

TxDataCon 05

TxDataMod 08

TxSymFreq 05

TxSym0H 00

TxSym0L 03

TxSym1H 00

TxSym1L 01

TxSym2 00

TxSym3 00

TxSym10Len AB

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 08

TxSym32Mod 00

RxBitMod 04

RxEofSym 00

RxSyncValH 00

RxSyncValL 00

RxSyncMod 02

CLRC66301, CLRC66302: 1DRxMod

CLRC66303: 0D

RxCorr 80

FabCal B2

Table 264. ISO/IEC14443-B 212 Classic (Protocol Number 05)

Value for register Value (hex)

TxBitMod 09

RFU 00

TxDataCon 06

TxDataMod 08

TxSymFreq 06

TxSym0H 00

TxSym0L 03

TxSym1H 00

Table 265. ISO/IEC14443-B 424, (Protocol Number 06)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 148 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

TxSym1L 01

TxSym2 00

TxSym3 00

TxSym10Len AB

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 08

TxSym32Mod 00

RxBitMod 04

RxEofSym 00

RxSyncValH 00

RxSyncValL 00

RxSyncMod 02

CLRC66301, CLRC66302: 1DRxMod

CLRC66303: 0D

RxCorr 80

FabCal B2

Table 265. ISO/IEC14443-B 424, (Protocol Number 06)...continued

Value for register Value (hex)

TxBitMod 09

RFU 00

TxDataCon 07

TxDataMod 08

TxSymFreq 07

TxSym0H 00

TxSym0L 03

TxSym1H 00

TxSym1L 01

TxSym2 00

TxSym3 00

TxSym10Len AB

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 08

TxSym32Mod 00

Table 266. ISO/IEC14443-B 848, (Protocol Number 07)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 149 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

RxBitMod 04

RxEofSym 00

RxSyncValH 00

RxSyncValL 00

RxSyncMod 02

CLRC66301, CLRC66302: 1DRxMod

CLRC66303: 0D

RxCorr 80

FabCal B2

Table 266. ISO/IEC14443-B 848, (Protocol Number 07)...continued

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon 05

TxDataMod 01

TxSymFreq 05

TxSym0H B2

TxSym0L 4D

TxSym1H 00

TxSym1L 00

TxSym2 00

TxSym3 00

TxSym10Len 0F

TxSym32Len 00

TxSym10BurstCtrl 01

TxSym10Mod 01

TxSym32Mod 00

RxBitMod 18

RxEofSym 00

RxSyncValH B2

RxSyncValL 4D

RxSyncMod F0

RxMod 19

RxCorr 20

FabCal B0

Table 267. JIS X 6319-4 (FeliCa) 212, (Protocol Number 08)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 150 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon 06

TxDataMod 01

TxSymFreq 06

TxSym0H B2

TxSym0L 4D

TxSym1H 00

TxSym1L 00

TxSym2 00

TxSym3 00

TxSym10Len 0F

TxSym32Len 00

TxSym10BurstCtrl 01

TxSym10Mod 01

TxSym32Mod 00

RxBitMod 18

RxEofSym 00

RxSyncValH B2

RxSyncValL 4D

RxSyncMod F0

RxMod 19

RxCorr 50

FabCal B0

Table 268. JIS X 6319-4 (FeliCa) 424, (Protocol Number 09)

Value for register Value (hex)

TxBitMod 00

RFU 00

TxDataCon 83

TxDataMod 04

TxSymFreq 40

TxSym0H 00

TxSym0L 00

TxSym1H 00

TxSym1L 00

Table 269. ISO/IEC15693 SLI 1/4 - SSC- 26, (Protocol Number 10)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 151 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

TxSym2 84

TxSym3 02

TxSym10Len 00

TxSym32Len 37

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 00

RxEofSym 1D

RxSyncValH 00

RxSyncValL 01

RxSyncMod 00

RxMod 24

RxCorr 60

FabCal F0

Table 269. ISO/IEC15693 SLI 1/4 - SSC- 26, (Protocol Number 10)...continued

Value for register Value (hex)

TxBitMod 00

RFU 00

TxDataCon 83

TxDataMod 04

TxSymFreq 40

TxSym0H 00

TxSym0L 00

TxSym1H 00

TxSym1L 00

TxSym2 84

TxSym3 02

TxSym10Len 00

TxSym32Len 37

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 00

RxEofSym 1D

Table 270. ISO/IEC15693 SLI 1/4 - SSC- 53, (Protocol Number 11)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 152 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

RxSyncValH 00

RxSyncValL 01

RxSyncMod 00

RxMod 24

RxCorr 40

FabCal F0

Table 270. ISO/IEC15693 SLI 1/4 - SSC- 53, (Protocol Number 11)...continued

Value for register Value (hex)

TxBitMod 00

RFU 00

TxDataCon 83

TxDataMod 04

TxSymFreq 40

TxSym0H 00

TxSym0L 00

TxSym1H 00

TxSym1L 00

TxSym2 81

TxSym3 02

TxSym10Len 00

TxSym32Len 37

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 00

RxEofSym 1D

RxSyncValH 00

RxSyncValL 01

RxSyncMod 00

RxMod 26

RxCorr 60

FabCal F0

Table 271. SO/IEC15693 SLI 1/256 - DSC, (Protocol Number 12)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 153 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon 44

TxDataMod 00

TxSymFreq 44

TxSym0H 08

TxSym0L 22

TxSym1H 08

TxSym1L 28

TxSym2 8A

TxSym3 02

TxSym10Len BB

TxSym32Len 37

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 08

RxEofSym 0B

RxSyncValH 00

RxSyncValL 00

RxSyncMod 08

RxMod 04

RxCorr 50

FabCal F0

Table 272. EPC/UID - SSC -26, (Protocol Number 13)

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon C5

TxDataMod 00

TxSymFreq 05

TxSym0H 68

TxSym0L 41

TxSym1H 01

TxSym1L A1

Table 273. EPC-V2 - 2/424 (Protocol Number 14)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 154 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

TxSym2 00

TxSym3 00

TxSym10Len 8E

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 08

RxEofSym 0B

RxSyncValH 00

RxSyncValL 01

RxSyncMod 04

RxMod 0C

RxCorr 40

FabCal F0

Table 273. EPC-V2 - 2/424 (Protocol Number 14)...continued

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon C5

TxDataMod 00

TxSymFreq 05

TxSym0H 68

TxSym0L 41

TxSym1H 01

TxSym1L A1

TxSym2 00

TxSym3 00

TxSym10Len 8E

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 08

RxEofSym 0B

Table 274. EPC-V2 - 4/424, (Protocol Number 15)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 155 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

RxSyncValH 00

RxSyncValL 01

RxSyncMod 04

RxMod 0C

RxCorr 50

FabCal F0

Table 274. EPC-V2 - 4/424, (Protocol Number 15)...continued

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon C5

TxDataMod 00

TxSymFreq 05

TxSym0H 68

TxSym0L 41

TxSym1H 01

TxSym1L A1

TxSym2 00

TxSym3 00

TxSym10Len 8E

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 08

RxEofSym 0B

RxSyncValH 00

RxSyncValL 01

RxSyncMod 04

RxMod 0C

RxCorr 88

FabCal F0

Table 275. EPC-V2 - 2/848, (Protocol Number 16)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 156 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

TxBitMod 80

RFU 00

TxDataCon C5

TxDataMod 00

TxSymFreq 05

TxSym0H 68

TxSym0L 41

TxSym1H 01

TxSym1L A1

TxSym2 00

TxSym3 00

TxSym10Len 8E

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 00

RxBitMod 08

RxEofSym 0B

RxSyncValH 00

RxSyncValL 01

RxSyncMod 04

RxMod 0C

RxCorr 80

FabCal F0

Table 276. EPC-V2 - 4/848, (Protocol Number 17)

Value for register Value (hex)

TxBitMod 00

RFU 00

TxDataCon 04

TxDataMod D0

TxSymFreq 40

TxSym0H 00

TxSym0L 00

TxSym1H 00

TxSym1L 00

Table 277. Jewel, (Protocol Number 18)

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 157 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register Value (hex)

TxSym2 00

TxSym3 00

TxSym10Len 00

TxSym32Len 00

TxSym10BurstCtrl 00

TxSym10Mod 00

TxSym32Mod 50

RxBitMod 02

RxEofSym 00

RxSyncValH 00

RxSyncValL 01

RxSyncMod 00

RxMod 08

RxCorr 80

FabCal F0

Table 277. Jewel, (Protocol Number 18)...continued

19.2 CLRC66303 EEPROM configuration

The CLRC66303 user EEPROM had been initalized with useful values for configuration

of the chip using a typical 65x65mm antenna. These values stored in EEPROM can be

used to configure the CLRC66303 with the command LoadReg.Typically, some of this

entries will be required to be modified compared to the preset values to achieve the best

RF performance for a specific antenna.

The registers 0x28...0x39 are relevant for configuration of the Antenna. For each

supported protocol, a dedicated preset configuration is available. To ensure compatibility

between products of the CLRC663 family, all products of the family use the same

default settings which are initialized in EEPROM, even if some of this protocols are not

supported by the product family member and cannot be used.

Alternatively, the registers can be initialized by individual register write commands.

Value for register EEPROM address (hex) Value (hex)

DrvMode C0 8E

TxAmp C1 12

DrvCon C2 39

TxI C3 0A

TXCrcPreset C4 18

RXCrcPreset C5 18

TxDataNum C6 0F

TxModWidth C7 21

Table 278. ISO/IEC14443-A 106 / MIFARE Classic

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 158 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

TxSym10BurstLen C8 00

TxWaitCtrl C9 C0

TxWaitLo CA 12

TxFrameCon CB CF

RxSofD CC 00

RxCtrl CD 04

RxWait CE 90

RxThreshold CF 5C

Rcv D0 12

RxAna D1 0A

Table 278. ISO/IEC14443-A 106 / MIFARE Classic...continued

Value for register EEPROM address (hex) Value (hex)

DrvMode D4 8E

TxAmp D5 D2

DrvCon D6 11

TxI D7 0A

TXCrcPreset D8 18

RXCrcPreset D9 18

TxDataNum DA 0F

TxModWidth DB 10

TxSym10BurstLen DC 00

TxWaitCtrl DD C0

TxWaitLo DE 12

TxFrameCon DF CF

RxSofD E0 00

RxCtrl E1 05

RxWait E2 90

RxThreshold E3 3C

Rcv E4 12

RxAna E5 0B

Table 279. ISO/IEC14443-A 212/ MIFARE Classic

Value for register EEPROM address (hex) Value (hex)

DrvMode E8 8F

Table 280. ISO/IEC14443-A 424/ MIFARE Classic

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 159 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

TxAmp E9 DE

DrvCon EA 11

TxI EB 0F

TXCrcPreset EC 18

RXCrcPreset ED 18

TxDataNum EE 0F

TxModWidth EF 07

TxSym10BurstLen F0 00

TxWaitCtrl F1 C0

TxWaitLo F2 12

TxFrameCon F3 CF

RxSofD F4 00

RxCtrl F5 06

RxWait F6 90

RxThreshold F7 2B

Rcv F8 12

RxAna F9 0B

Table 280. ISO/IEC14443-A 424/ MIFARE Classic...continued

Value for register EEPROM address (hex) Value (hex)

DrvMode 0100 8F

TxAmp 0101 DB

DrvCon 0102 21

TxI 0103 0F

TXCrcPreset 0104 18

RXCrcPreset 0105 18

TxDataNum 0106 0F

TxModWidth 0107 02

TxSym10BurstLen 0108 00

TxWaitCtrl 0109 C0

TxWaitLo 010A 12

TxFrameCon 010B CF

RxSofD 010C 00

RxCtrl 010D 07

RxWait 010E 90

RxThreshold 010F 3A

Table 281. ISO/IEC14443-A 848/ MIFARE Classic

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 160 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

Rcv 0110 12

RxAna 0111 0B

Table 281. ISO/IEC14443-A 848/ MIFARE Classic...continued

Value for register EEPROM address (hex) Value (hex)

DrvMode 0114 8F

TxAmp 0115 0E

DrvCon 0116 09

TxI 0117 0A

TXCrcPreset 0118 7B

RXCrcPreset 0119 7B

TxDataNum 011A 08

TxModWidth 011B 00

TxSym10BurstLen 011C 00

TxWaitCtrl 011D 01

TxWaitLo 011E 00

TxFrameCon 011F 05

RxSofD 0120 00

RxCtrl 0121 34

RxWait 0122 90

RxThreshold 0123 6F

Rcv 0124 12

RxAna 0125 03

Table 282. ISO/IEC14443-B 106

Value for register EEPROM address (hex) Value (hex)

DrvMode 0128 8F

TxAmp 0129 0E

DrvCon 012A 09

TxI 012B 0A

TXCrcPreset 012C 7B

RXCrcPreset 012D 7B

TxDataNum 012E 08

TxModWidth 012F 00

TxSym10BurstLen 0130 00

Table 283. ISO/IEC14443-B 212

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 161 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

TxWaitCtrl 0131 01

TxWaitLo 0132 00

TxFrameCon 0133 05

RxSofD 0134 00

RxCtrl 0135 35

RxWait 0136 90

RxThreshold 0137 3F

Rcv 0138 12

RxAna 0139 03

Table 283. ISO/IEC14443-B 212...continued

Value for register EEPROM address (hex) Value (hex)

DrvMode 0140 8F

TxAmp 0141 0F

DrvCon 0142 09

TxI 0143 0A

TXCrcPreset 0144 7B

RXCrcPreset 0145 7B

TxDataNum 0146 08

TxModWidth 0147 00

TxSym10BurstLen 0148 00

TxWaitCtrl 0149 01

TxWaitLo 014A 00

TxFrameCon 014B 05

RxSofD 014C 00

RxCtrl 014D 36

RxWait 014E 90

RxThreshold 014F 3F

Rcv 0150 12

RxAna 0151 03

Table 284. ISO/IEC14443-B 424

Value for register EEPROM address (hex) Value (hex)

DrvMode 0154 8F

TxAmp 0155 10

Table 285. ISO/IEC14443-B 848

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 162 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

DrvCon 0156 09

TxI 0157 0A

TXCrcPreset 0158 7B

RXCrcPreset 0159 7B

TxDataNum 015A 08

TxModWidth 015B 00

TxSym10BurstLen 015C 00

TxWaitCtrl 015D 01

TxWaitLo 015E 00

TxFrameCon 015F 05

RxSofD 0160 00

RxCtrl 0161 37

RxWait 0162 90

RxThreshold 0163 3F

Rcv 0164 12

RxAna 0165 03

Table 285. ISO/IEC14443-B 848...continued

Value for register EEPROM address (hex) Value (hex)

DrvMode 0168 8F

TxAmp 0169 17

DrvCon 016A 01

TxI 016B 06

TXCrcPreset 016C 09

RXCrcPreset 016D 09

TxDataNum 016E 08

TxModWidth 016F 00

TxSym10BurstLen 0170 03

TxWaitCtrl 0171 80

TxWaitLo 0172 12

TxFrameCon 0173 01

RxSofD 0174 00

RxCtrl 0175 05

RxWait 0176 86

RxThreshold 0177 3F

Rcv 0178 12

Table 286. JIS X 6319-4 (FeliCa) 212

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 163 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

RxAna 0179 02

Table 286. JIS X 6319-4 (FeliCa) 212...continued

Value for register EEPROM address (hex) Value (hex)

DrvMode 0180 8F

TxAmp 0181 17

DrvCon 0182 01

TxI 0183 06

TXCrcPreset 0184 09

RXCrcPreset 0185 09

TxDataNum 0186 08

TxModWidth 0187 00

TxSym10BurstLen 0188 03

TxWaitCtrl 0189 80

TxWaitLo 018A 12

TxFrameCon 018B 01

RxSofD 018C 00

RxCtrl 018D 06

RxWait 018E 86

RxThreshold 018F 3F

Rcv 0190 12

RxAna 0191 02

Table 287. JIS X 6319-4 (FeliCa) 424

Value for register EEPROM address (hex) Value (hex)

DrvMode 0194 89

TxAmp 0195 10

DrvCon 0196 09

TxI 0197 0A

TXCrcPreset 0198 7B

RXCrcPreset 0199 7B

TxDataNum 019A 08

TxModWidth 019B 00

TxSym10BurstLen 019C 00

TxWaitCtrl 019D 88

Table 288. ISO/IEC15693 SLI 1/4 - SSC- 26

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 164 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

TxWaitLo 019E A9

TxFrameCon 019F 0F

RxSofD 01A0 00

RxCtrl 01A1 02

RxWait 01A2 9C

RxThreshold 01A3 74

Rcv 01A4 12

RxAna 01A5 07

Table 288. ISO/IEC15693 SLI 1/4 - SSC- 26...continued

Value for register EEPROM address (hex) Value (hex)

DrvMode 01A8 89

TxAmp 01A9 10

DrvCon 01AA 09

TxI 01AB 0A

TXCrcPreset 01AC 7B

RXCrcPreset 01AD 7B

TxDataNum 01AE 08

TxModWidth 016F 00

TxSym10BurstLen 01B0 00

TxWaitCtrl 01B1 88

TxWaitLo 01B2 A9

TxFrameCon 01B3 0F

RxSofD 01B4 00

RxCtrl 01B5 03

RxWait 01B6 9C

RxThreshold 01B7 74

Rcv 01B8 12

RxAna 01B9 03

Table 289. ISO/IEC15693 SLI 1/4 - SSC-53

Value for register EEPROM address (hex) Value (hex)

DrvMode 01C0 8E

TxAmp 01C1 10

DrvCon 01C2 01

Table 290. ISO/IEC15693 SLI 1/256 - DSC

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 165 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

TxI 01C3 06

TXCrcPreset 01C4 7B

RXCrcPreset 01C5 7B

TxDataNum 01C6 08

TxModWidth 01C7 00

TxSym10BurstLen 01C8 00

TxWaitCtrl 01C9 88

TxWaitLo 01CA A9

TxFrameCon 01CB 0F

RxSofD 01CC 00

RxCtrl 01CD 02

RxWait 01CE 10

RxThreshold 01CF 44

Rcv 01D0 12

RxAna 01D1 06

Table 290. ISO/IEC15693 SLI 1/256 - DSC...continued

Value for register EEPROM address (hex) Value (hex)

DrvMode 01D4 8F

TxAmp 01D5 10

DrvCon 01D6 01

TxI 01D7 06

TXCrcPreset 01D8 74

RXCrcPreset 01D9 7B

TxDataNum 01DA 18

TxModWidth 01DB 00

TxSym10BurstLen 01DC 00

TxWaitCtrl 01DD 50

TxWaitLo 01DE 5C

TxFrameCon 01DF 0F

RxSofD 01E0 00

RxCtrl 01E1 03

RxWait 01E2 10

RxThreshold 01E3 4E

Rcv 01E4 12

RxAna 01E5 06

Table 291. EPC/UID - SSC -26

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 166 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

DrvMode 01E8 8F

TxAmp 01E9 10

DrvCon 01EA 09

TxI 01EB 0A

TXCrcPreset 01EC 11

RXCrcPreset 01ED 91

TxDataNum 01EE 09

TxModWidth 01EF 00

TxSym10BurstLen 01F0 00

TxWaitCtrl 01F1 80

TxWaitLo 01F2 12

TxFrameCon 01F3 01

RxSofD 01F4 00

RxCtrl 01F5 03

RxWait 01F6 A0

RxThreshold 01F7 56

Rcv 01F8 12

RxAna 01F9 0F

Table 292. EPC-V2 - 2/424

Value for register EEPROM address (hex) Value (hex)

DrvMode 0200 8F

TxAmp 0201 10

DrvCon 0202 09

TxI 0203 0A

TXCrcPreset 0204 11

RXCrcPreset 0205 91

TxDataNum 0206 09

TxModWidth 0207 00

TxSym10BurstLen 0208 00

TxWaitCtrl 0209 80

TxWaitLo 020A 12

TxFrameCon 020B 01

RxSofD 020C 00

RxCtrl 020D 03

RxWait 020E A0

Table 293. EPC-V2 - 4/424

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 167 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

RxThreshold 020F 56

Rcv 0210 12

RxAna 0211 0F

Table 293. EPC-V2 - 4/424...continued

Value for register EEPROM address (hex) Value (hex)

DrvMode 0214 8F

TxAmp 0215 D0

DrvCon 0216 01

TxI 0217 0A

TXCrcPreset 0218 11

RXCrcPreset 0219 91

TxDataNum 021A 09

TxModWidth 021B 00

TxSym10BurstLen 021C 00

TxWaitCtrl 021D 80

TxWaitLo 021E 12

TxFrameCon 021F 01

RxSofD 0220 00

RxCtrl 0221 05

RxWait 0222 A0

RxThreshold 0223 26

Rcv 0224 12

RxAna 0225 0E

Table 294. EPC-V2 - 2/848

Value for register EEPROM address (hex) Value (hex)

DrvMode 0228 8F

TxAmp 0229 D0

DrvCon 022A 01

TxI 022B 0A

TXCrcPreset 022C 11

RXCrcPreset 022D 91

TxDataNum 022E 09

TxModWidth 022F 00

Table 295. EPC-V2 - 4/848

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 168 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

TxSym10BurstLen 0230 00

TxWaitCtrl 0231 80

TxWaitLo 0232 12

TxFrameCon 0233 01

RxSofD 0234 00

RxCtrl 0235 05

RxWait 0236 A0

RxThreshold 0237 26

Rcv 0238 12

RxAna 0239 0E

Table 295. EPC-V2 - 4/848...continued

Value for register EEPROM address (hex) Value (hex)

DrvMode 0240 8E

TxAmp 0241 15

DrvCon 0242 11

TxI 0243 06

TXCrcPreset 0244 18

RXCrcPreset 0245 18

TxDataNum 0246 0F

TxModWidth 0247 20

TxSym10BurstLen 0248 00

TxWaitCtrl 0249 40

TxWaitLo 024A 09

TxFrameCon 024B 4F

RxSofD 024C 00

RxCtrl 024D 04

RxWait 024E 8F

RxThreshold 024F 32

Rcv 0250 12

RxAna 0251 0A

Table 296. Jewel

Value for register EEPROM address (hex) Value (hex)

DrvMode 0254 8F

Table 297. ISO/IEC14443 - B 106 EMVCo Optimized

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 169 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Value for register EEPROM address (hex) Value (hex)

TxAmp 0255 0E

DrvCon 0256 09

TxI 0257 0A

TXCrcPreset 0258 7B

RXCrcPreset 0259 7B

TxDataNum 025A 08

TxModWidth 025B 00

TxSym10BurstLen 025C 00

TxWaitCtrl 025D 01

TxWaitLo 025E 00

TxFrameCon 025F 05

RxSofD 0260 00

RxCtrl 0261 34

RxWait 0262 90

RxThreshold 0263 9F

Rcv 0264 12

RxAna 0265 03

Table 297. ISO/IEC14443 - B 106 EMVCo Optimized...continued

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 170 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

20 Abbreviations

Acronym Description

ADC Analog-to-Digital Converter

BPSK Binary Phase Shift Keying

CRC Cyclic Redundancy Check

CW Continuous Wave

EGT Extra Guard Time

EMC Electro Magnetic Compatibility

EMD Electro Magnetic Disturbance

EOF End Of Frame

EPC Electronic Product Code

ETU Elementary Time Unit

GPIO General Purpose Input/Output

HBM Human Body Model

I2C Inter-Integrated Circuit

IRQ Interrupt Request

LFO Low Frequency Oscillator

LPCD Low-Power Card Detection

LSB Least Significant Bit

MISO Master In Slave Out

MOSI Master Out Slave In

MSB Most Significant Bit

NRZ Not Return to Zero

NSS Not Slave Select

PCD Proximity Coupling Device

PLL Phase-Locked Loop

RZ Return To Zero

RX Receiver

SAM Secure Access Module

SOF Start Of Frame

SPI Serial Peripheral Interface

SW Software

TTimer Timing of the clk period

TX Transmitter

UART Universal Asynchronous Receiver Transmitter

UID Unique Identification

Table 298. Abbreviations

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 171 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Acronym Description

VCO Voltage Controlled Oscillator

Table 298. Abbreviations...continued

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 172 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

21 References

[1]

Application note AN11019

CLRC663, MFRC630, MFRC631, SLRC610 Antenna Design Guide

[2]

Application note AN11783

CLRC663 plus Low Power Card Detection

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 173 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

22 Revision history

Document ID Release date Data sheet status Change notice Supersedes

CLRC663 v.5.0 20201127 Product data sheet - CLRC663 v.4.9

Modifications: •Section 5 "Ordering information": MSL corrected

•Table 29 "Boundary scan path of the CLRC663": Cell BC_4 corrected

CLRC663 v.4.9 20200701 Product data sheet - CLRC663 v.4.8

CLRC663 v.4.8 20191028 Product data sheet - CLRC663 v.4.7

CLRC663 v.4.7 20180912 Product data sheet - CLRC663 v.4.6

CLRC663 v.4.6 20180516 Product data sheet - CLRC663 v.4.5

CLRC663 v.4.5 20171219 Product data sheet - CLRC663 v.4.4

CLRC663 v.4.4 20170502 Product data sheet - CLRC663 v.4.3

CLRC663 v.4.3 20170220 Product data sheet - CLRC663 v.4.2

CLRC663 v.4.2 20160427 Product data sheet - CLRC663 v.4.1

CLRC663 v.4.1 20160211 Product data sheet - CLRC663 v.4.0

CLRC663 v.4.0 20151029 Product data sheet - CLRC663 v.3.9

CLRC663 v.3.9 20150722 Product data sheet - CLRC663 v.3.8

CLRC663 v.3.7 20140206 Product data sheet - CLRC663 v.3.7

CLRC663 v.3.7 20140204 Product data sheet - CLRC663 v.3.6

CLRC663 v.3.6 20130910 Product data sheet - CLRC663 v.3.5

CLRC663 v.3.5 20120905 Product data sheet - CLRC663 v.3.4

CLRC663 v.3.4 20120717 Product data sheet - CLRC663 v.3.3

CLRC663 v.3.3 20120402 Product data sheet - CLRC663 v.3.2

CLRC663 v.3.2 20120202 Product data sheet - CLRC663 v.3.1

CLRC663 v.3.1 20110926 Product data sheet - CLRC663 v.3.0

CLRC663 v.3.0 20110919 Product data sheet - CLRC663 v.2.0

CLRC663 v.2.0 20110615 Preliminary data sheet - CLRC663 v.1.0

CLRC663 v.1.0 20110308 Objective data sheet - -

Table 299. Revision history

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 174 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

23 Legal information

23.1 Data sheet status

Document status[1][2] Product status[3] Definition

Objective [short] data sheet Development This document contains data from the objective specification for product

development.

Preliminary [short] data sheet Qualification This document contains data from the preliminary specification.

Product [short] data sheet Production This document contains the product specification.

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term 'short data sheet' is explained in section "Definitions".

[3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple

devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

23.2 Definitions

Draft — A draft status on a document indicates that the content is still

under internal review and subject to formal approval, which may result

in modifications or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included in a draft version of a document and shall have no

liability for the consequences of use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and title. A short data sheet is

intended for quick reference only and should not be relied upon to contain

detailed and full information. For detailed and full information see the

relevant full data sheet, which is available on request via the local NXP

Semiconductors sales office. In case of any inconsistency or conflict with the

short data sheet, the full data sheet shall prevail.

Product specification — The information and data provided in a Product

data sheet shall define the specification of the product as agreed between

NXP Semiconductors and its customer, unless NXP Semiconductors and

customer have explicitly agreed otherwise in writing. In no event however,

shall an agreement be valid in which the NXP Semiconductors product

is deemed to offer functions and qualities beyond those described in the

Product data sheet.

23.3 Disclaimers

Limited warranty and liability — Information in this document is believed

to be accurate and reliable. However, NXP Semiconductors does not

give any representations or warranties, expressed or implied, as to the

accuracy or completeness of such information and shall have no liability

for the consequences of use of such information. NXP Semiconductors

takes no responsibility for the content in this document if provided by an

information source outside of NXP Semiconductors. In no event shall NXP

Semiconductors be liable for any indirect, incidental, punitive, special or

consequential damages (including - without limitation - lost profits, lost

savings, business interruption, costs related to the removal or replacement

of any products or rework charges) whether or not such damages are based

on tort (including negligence), warranty, breach of contract or any other

legal theory. Notwithstanding any damages that customer might incur for

any reason whatsoever, NXP Semiconductors’ aggregate and cumulative

liability towards customer for the products described herein shall be limited

in accordance with the Terms and conditions of commercial sale of NXP

Semiconductors.

Right to make changes — NXP Semiconductors reserves the right to

make changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all information supplied prior

to the publication hereof.

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suitable for use in life support, life-critical or

safety-critical systems or equipment, nor in applications where failure or

malfunction of an NXP Semiconductors product can reasonably be expected

to result in personal injury, death or severe property or environmental

damage. NXP Semiconductors and its suppliers accept no liability for

inclusion and/or use of NXP Semiconductors products in such equipment or

applications and therefore such inclusion and/or use is at the customer’s own

risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes

no representation or warranty that such applications will be suitable

for the specified use without further testing or modification. Customers

are responsible for the design and operation of their applications and

products using NXP Semiconductors products, and NXP Semiconductors

accepts no liability for any assistance with applications or customer product

design. It is customer’s sole responsibility to determine whether the NXP

Semiconductors product is suitable and fit for the customer’s applications

and products planned, as well as for the planned application and use of

customer’s third party customer(s). Customers should provide appropriate

design and operating safeguards to minimize the risks associated with

their applications and products. NXP Semiconductors does not accept any

liability related to any default, damage, costs or problem which is based

on any weakness or default in the customer’s applications or products, or

the application or use by customer’s third party customer(s). Customer is

responsible for doing all necessary testing for the customer’s applications

and products using NXP Semiconductors products in order to avoid a

default of the applications and the products or of the application or use by

customer’s third party customer(s). NXP does not accept any liability in this

respect.

Limiting values — Stress above one or more limiting values (as defined in

the Absolute Maximum Ratings System of IEC 60134) will cause permanent

damage to the device. Limiting values are stress ratings only and (proper)

operation of the device at these or any other conditions above those

given in the Recommended operating conditions section (if present) or the

Characteristics sections of this document is not warranted. Constant or

repeated exposure to limiting values will permanently and irreversibly affect

the quality and reliability of the device.

Terms and conditions of commercial sale — NXP Semiconductors

products are sold subject to the general terms and conditions of commercial

sale, as published at http://www.nxp.com/profile/terms, unless otherwise

agreed in a valid written individual agreement. In case an individual

agreement is concluded only the terms and conditions of the respective

agreement shall apply. NXP Semiconductors hereby expressly objects to

applying the customer’s general terms and conditions with regard to the

purchase of NXP Semiconductors products by customer.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 175 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

No offer to sell or license — Nothing in this document may be interpreted

or construed as an offer to sell products that is open for acceptance or

the grant, conveyance or implication of any license under any copyrights,

patents or other industrial or intellectual property rights.

Quick reference data — The Quick reference data is an extract of the

product data given in the Limiting values and Characteristics sections of this

document, and as such is not complete, exhaustive or legally binding.

Export control — This document as well as the item(s) described herein

may be subject to export control regulations. Export might require a prior

authorization from competent authorities.

Non-automotive qualified products — Unless this data sheet expressly

states that this specific NXP Semiconductors product is automotive qualified,

the product is not suitable for automotive use. It is neither qualified nor

tested in accordance with automotive testing or application requirements.

NXP Semiconductors accepts no liability for inclusion and/or use of non-

automotive qualified products in automotive equipment or applications. In

the event that customer uses the product for design-in and use in automotive

applications to automotive specifications and standards, customer (a) shall

use the product without NXP Semiconductors’ warranty of the product for

such automotive applications, use and specifications, and (b) whenever

customer uses the product for automotive applications beyond NXP

Semiconductors’ specifications such use shall be solely at customer’s own

risk, and (c) customer fully indemnifies NXP Semiconductors for any liability,

damages or failed product claims resulting from customer design and use

of the product for automotive applications beyond NXP Semiconductors’

standard warranty and NXP Semiconductors’ product specifications.

Translations — A non-English (translated) version of a document is for

reference only. The English version shall prevail in case of any discrepancy

between the translated and English versions.

Security — Customer understands that all NXP products may be subject

to unidentified or documented vulnerabilities. Customer is responsible

for the design and operation of its applications and products throughout

their lifecycles to reduce the effect of these vulnerabilities on customer’s

applications and products. Customer’s responsibility also extends to other

open and/or proprietary technologies supported by NXP products for use

in customer’s applications. NXP accepts no liability for any vulnerability.

Customer should regularly check security updates from NXP and follow up

appropriately. Customer shall select products with security features that best

meet rules, regulations, and standards of the intended application and make

the ultimate design decisions regarding its products and is solely responsible

for compliance with all legal, regulatory, and security related requirements

concerning its products, regardless of any information or support that may

be provided by NXP. NXP has a Product Security Incident Response Team

(PSIRT) (reachable at PSIRT@nxp.com) that manages the investigation,

reporting, and solution release to security vulnerabilities of NXP products.

23.4 Licenses

Purchase of NXP ICs with ISO/IEC 14443 type B functionality

RATP/Innovatron

Technology

This NXP Semiconductors IC is ISO/IEC

14443 Type B software enabled and is

licensed under Innovatron’s Contactless

Card patents license for ISO/IEC 14443 B.

The license includes the right to use the IC

in systems and/or end-user equipment.

Purchase of NXP ICs with NFC technology

Purchase of an NXP Semiconductors IC that complies with one of the

Near Field Communication (NFC) standards ISO/IEC 18092 and ISO/

IEC 21481 does not convey an implied license under any patent right

infringed by implementation of any of those standards. Purchase of NXP

Semiconductors IC does not include a license to any NXP patent (or other

IP right) covering combinations of those products with other products,

whether hardware or software.

23.5 Trademarks

Notice: All referenced brands, product names, service names and

trademarks are the property of their respective owners.

I2C-bus — logo is a trademark of NXP B.V.

MIFARE — is a trademark of NXP B.V.

DESFire — is a trademark of NXP B.V.

ICODE and I-CODE — are trademarks of NXP B.V.

MIFARE Plus — is a trademark of NXP B.V.

MIFARE Ultralight — is a trademark of NXP B.V.

MIFARE Classic — is a trademark of NXP B.V.

NXP — wordmark and logo are trademarks of NXP B.V.

FeliCa — is a trademark of Sony Corporation.

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 176 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Tables

Tab. 1. Quick reference data CLRC66301 and

CLRC66302 .......................................................5

Tab. 2. Quick reference data CLRC66303 .................... 5

Tab. 3. Ordering information ..........................................6

Tab. 4. Pin description ...................................................8

Tab. 5. Pin description VFBGA36 ................................. 9

Tab. 6. Interrupt sources ............................................. 12

Tab. 7. Communication overview for ISO/IEC

14443 type A and read/write mode for

MIFARE Classic .............................................. 15

Tab. 8. Communication overview for ISO/IEC

14443 B reader/writer ......................................17

Tab. 9. Communication overview for FeliCa reader/

writer ................................................................18

Tab. 10. FeliCa framing and coding .............................. 18

Tab. 11. Communication overview for ISO/IEC

15693 reader/writer reader to label ................. 18

Tab. 12. Communication overview for ISO/IEC

15693 reader/writer label to reader ................. 19

Tab. 13. Communication overview for EPC/UID ............19

Tab. 14. Communication overview for Passive

communication mode ...................................... 21

Tab. 15. Framing and coding overview ......................... 21

Tab. 16. Connection scheme for detecting the

different interface types ...................................22

Tab. 17. Byte Order for MOSI and MISO ...................... 23

Tab. 18. Byte Order for MOSI and MISO ...................... 23

Tab. 19. Address byte 0 register; address MOSI ...........23

Tab. 20. Timing conditions SPI ..................................... 24

Tab. 21. Settings of BR_T0 and BR_T1 ........................25

Tab. 22. Selectable transfer speeds ..............................25

Tab. 23. UART framing ................................................. 25

Tab. 24. Byte Order to Read Data ................................ 26

Tab. 25. Byte Order to Write Data ................................ 26

Tab. 26. Timing parameter I2CL ................................... 31

Tab. 27. SPI SAM connection ....................................... 33

Tab. 28. Boundary scan command ............................... 33

Tab. 29. Boundary scan path of the CLRC663 ..............36

Tab. 30. Settings for TX1 and TX2 ............................... 40

Tab. 31. Setting residual carrier and modulation

index by TXamp.set_residual_carrier .............. 40

Tab. 32. Configuration for single or differential

receiver ............................................................43

Tab. 33. Register configuration of CLRC663 active

antenna concept (DIGITAL) .............................44

Tab. 34. Register configuration of CLRC663 active

antenna concept (Antenna) ............................. 44

Tab. 35. EEPROM memory organization ...................... 47

Tab. 36. Production area (Page 0) ................................47

Tab. 37. Product ID overview of CLRC663 family ......... 48

Tab. 38. Configuration area (Page 0) ............................48

Tab. 39. Interface byte .................................................. 48

Tab. 40. Interface bits ....................................................49

Tab. 41. Tx and Rx arrangements in the register set

protocol area ................................................... 49

Tab. 42. Register reset values (Hex.) (Page0) .............. 49

Tab. 43. Register reset values (Hex.)(Page1 and

page 2) ............................................................ 50

Tab. 44. Crystal requirements recommendations .......... 51

Tab. 45. Divider values for selected frequencies

using the integerN PLL ................................... 52

Tab. 46. Command set ..................................................55

Tab. 47. Predefined protocol overview RX .................... 59

Tab. 48. Predefined protocol overview TX .................... 59

Tab. 49. Behavior of register bits and their

designation ...................................................... 62

Tab. 50. CLRC663 registers overview ...........................62

Tab. 51. Command register (address 00h) ....................65

Tab. 52. Command bits ................................................. 65

Tab. 53. HostCtrl register (address 01h); ...................... 66

Tab. 54. HostCtrl bits .....................................................66

Tab. 55. FIFOControl register (address 02h); ............... 66

Tab. 56. FIFOControl bits ..............................................66

Tab. 57. WaterLevel register (address 03h); ................. 67

Tab. 58. WaterLevel bits ................................................67

Tab. 59. FIFOLength register (address 04h); reset

value: 00h ........................................................68

Tab. 60. FIFOLength bits .............................................. 68

Tab. 61. FIFOData register (address 05h); ................... 68

Tab. 62. FIFOData bits ..................................................68

Tab. 63. IRQ0 register (address 06h); reset value:

00h .................................................................. 69

Tab. 64. IRQ0 bits ......................................................... 69

Tab. 65. IRQ1 register (address 07h) ............................69

Tab. 66. IRQ1 bits ......................................................... 70

Tab. 67. IRQ0En register (address 08h) ....................... 70

Tab. 68. IRQ0En bits .....................................................70

Tab. 69. IRQ1EN register (address 09h); ......................71

Tab. 70. IRQ1EN bits .................................................... 71

Tab. 71. Error register (address 0Ah) ............................71

Tab. 72. Error bits ..........................................................71

Tab. 73. Status register (address 0Bh) ......................... 72

Tab. 74. Status bits ....................................................... 73

Tab. 75. RxBitCtrl register (address 0Ch); .................... 73

Tab. 76. RxBitCtrl bits ................................................... 73

Tab. 77. RxColl register (address 0Dh); ........................74

Tab. 78. RxColl bits ....................................................... 74

Tab. 79. TControl register (address 0Eh) ......................75

Tab. 80. TControl bits ....................................................75

Tab. 81. T0Control register (address 0Fh); ................... 75

Tab. 82. T0Control bits ..................................................75

Tab. 83. T0ReloadHi register (address 10h); ................ 76

Tab. 84. T0ReloadHi bits ...............................................76

Tab. 85. T0ReloadLo register (address 11h); ................76

Tab. 86. T0ReloadLo bits .............................................. 77

Tab. 87. T0CounterValHi register (address 12h) ........... 77

Tab. 88. T0CounterValHi bits ........................................ 77

Tab. 89. T0CounterValLo register (address 13h) .......... 77

Tab. 90. T0CounterValLo bits ........................................77

Tab. 91. T1Control register (address 14h); ................... 77

Tab. 92. T1Control bits ..................................................78

Tab. 93. T0ReloadHi register (address 15h) ................. 78

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 177 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Tab. 94. T1ReloadHi bits ...............................................78

Tab. 95. T1ReloadLo register (address 16h) .................78

Tab. 96. T1ReloadLo bits .............................................. 79

Tab. 97. T1CounterValHi register (address 17h) ........... 79

Tab. 98. T1CounterValHi bits ........................................ 79

Tab. 99. T1CounterValLo register (address 18h) .......... 79

Tab. 100. T1CounterValLo bits ........................................79

Tab. 101. T2Control register (address 19h) .................... 79

Tab. 102. T2Control bits ..................................................80

Tab. 103. T2ReloadHi register (address 1Ah) ................. 80

Tab. 104. T2ReloadHi bits ...............................................80

Tab. 105. T2ReloadLo register (address 1Bh) ................ 80

Tab. 106. T2ReloadLo bits .............................................. 81

Tab. 107. T2CounterValHi register (address 1Ch) .......... 81

Tab. 108. T2CounterValHi bits ........................................ 81

Tab. 109. T2CounterValLo register (address 1Dh) .......... 81

Tab. 110. T2CounterValLo bits ........................................81

Tab. 111. T3Control register (address 1Eh) .................... 81

Tab. 112. T3Control bits ..................................................82

Tab. 113. T3ReloadHi register (address 1Fh); ................ 82

Tab. 114. T3ReloadHi bits ...............................................82

Tab. 115. T3ReloadLo register (address 20h) .................82

Tab. 116. T3ReloadLo bits .............................................. 83

Tab. 117. T3CounterValHi register (address 21h) ........... 83

Tab. 118. T3CounterValHi bits ........................................ 83

Tab. 119. T3CounterValLo register (address 22h) .......... 83

Tab. 120. T3CounterValLo bits ........................................83

Tab. 121. T4Control register (address 23h) .................... 83

Tab. 122. T4Control bits ..................................................84

Tab. 123. T4ReloadHi register (address 24h) ................. 84

Tab. 124. T4ReloadHi bits ...............................................85

Tab. 125. T4ReloadLo register (address 25h) .................85

Tab. 126. T4ReloadLo bits .............................................. 85

Tab. 127. T4CounterValHi register (address 26h) ........... 85

Tab. 128. T4CounterValHi bits ........................................ 85

Tab. 129. T4CounterValLo register (address 27h) .......... 85

Tab. 130. T4CounterValLo bits ........................................86

Tab. 131. DrvMode register (address 28h) ......................86

Tab. 132. DrvMode bits ................................................... 86

Tab. 133. TxAmp register (address 29h) .........................86

Tab. 134. TxAmp bits ...................................................... 87

Tab. 135. TxCon register (address 2Ah) ......................... 87

Tab. 136. TxCon bits ....................................................... 87

Tab. 137. Txl register (address 2Bh) ...............................87

Tab. 138. Txl bits .............................................................88

Tab. 139. TXCrcPreset register (address 2Ch) ............... 88

Tab. 140. TxCrcPreset bits ..............................................88

Tab. 141. Transmitter CRC preset value configuration ....88

Tab. 142. RxCrcCon register (address 2Dh) ................... 89

Tab. 143. RxCrcCon bits ................................................. 89

Tab. 144. Receiver CRC preset value configuration ....... 89

Tab. 145. TxDataNum register (address 2Eh) .................90

Tab. 146. TxDataNum bits .............................................. 90

Tab. 147. TxDataModWidth register (address 2Fh) ........ 90

Tab. 148. TxDataModWidth bits ...................................... 90

Tab. 149. TxSym10BurstLen register (address 30h) ....... 91

Tab. 150. TxSym10BurstLen bits .................................... 91

Tab. 151. TxWaitCtrl register (address 31h); reset

value: C0h ....................................................... 91

Tab. 152. TXWaitCtrl bits ................................................ 92

Tab. 153. TxWaitLo register (address 32h) ..................... 92

Tab. 154. TxWaitLo bits ...................................................92

Tab. 155. FrameCon register (address 33h) ................... 92

Tab. 156. FrameCon bits .................................................93

Tab. 157. RxSofD register (address 34h) ........................93

Tab. 158. RxSofD bits ..................................................... 93

Tab. 159. RxCtrl register (address 35h) .......................... 93

Tab. 160. RxCtrl bits ........................................................94

Tab. 161. RxWait register (address 36h) .........................94

Tab. 162. RxWait bits ...................................................... 95

Tab. 163. RxThreshold register (address 37h) ................95

Tab. 164. RxThreshold bits ............................................. 95

Tab. 165. Rcv register (address 38h) ..............................95

Tab. 166. Rcv bits ........................................................... 95

Tab. 167. RxAna register (address 39h) ......................... 96

Tab. 168. RxAna bits .......................................................96

Tab. 169. Effect of gain and high-pass corner register

settings ............................................................ 96

Tab. 170. SerialSpeed register (address3Bh); reset

value: 7Ah ....................................................... 97

Tab. 171. SerialSpeed bits .............................................. 97

Tab. 172. RS232 speed settings ..................................... 97

Tab. 173. LFO_Trimm register (address 3Ch) .................98

Tab. 174. LFO_Trimm bits ...............................................98

Tab. 175. PLL_Ctrl register (address3Dh) .......................98

Tab. 176. PLL_Ctrl register bits .......................................99

Tab. 177. Setting of feedback divider PLLDiv_FB

[1:0] ................................................................. 99

Tab. 178. PLLDiv_Out register (address 3Eh) ................ 99

Tab. 179. PLLDiv_Out bits .............................................. 99

Tab. 180. Setting for the output divider ratio PLLDiv_

Out [7:0] .......................................................... 99

Tab. 181. LPCD_QMin register (address 3Fh) .............. 100

Tab. 182. LPCD_QMin bits ............................................100

Tab. 183. LPCD_QMax register (address 40h) ............. 100

Tab. 184. LPCD_QMax bits ...........................................101

Tab. 185. LPCD_IMin register (address 41h) ................ 101

Tab. 186. LPCD_IMin bits ............................................. 101

Tab. 187. LPCD_Result_I register (address 42h) ..........101

Tab. 188. LPCD_Result_I bits ....................................... 102

Tab. 189. LPCD_Result_Q register (address 43h) ........ 102

Tab. 190. LPCD_Result_Q bits ..................................... 102

Tab. 191. LPCD_Options register (address 3Ah) .......... 102

Tab. 192. LPCD_Options ...............................................102

Tab. 193. PadEn register (address 44h) ....................... 103

Tab. 194. PadEn bits .....................................................103

Tab. 195. PadOut register (address 45h) ......................104

Tab. 196. PadOut bits ................................................... 104

Tab. 197. PadIn register (address 46h) .........................104

Tab. 198. PadIn bits ...................................................... 104

Tab. 199. SigOut register (address 47h) ....................... 105

Tab. 200. SigOut bits .....................................................105

Tab. 201. TxBitMod register (address 48h) ................... 106

Tab. 202. TxBitMod bits ................................................ 106

Tab. 203. TxDataCon (address 4Ah) ............................ 106

Tab. 204. TxDataCon bits ............................................. 107

Tab. 205. TxDataMod register (address 4Bh) ............... 107

Tab. 206. TxDataMod bits ............................................. 108

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 178 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Tab. 207. TxSymFreq (address 4Ch) ............................ 108

Tab. 208. TxSymFreq bits ............................................. 108

Tab. 209. TxSym0_H (address 4Dh) .............................109

Tab. 210. TxSym0_H bits ..............................................109

Tab. 211. TxSym0_L (address 4Eh) ............................. 109

Tab. 212. TxSYM0_L bits ..............................................110

Tab. 213. TxSym1_H (address 4Fh) ............................. 110

Tab. 214. TxSym1_H bits ..............................................110

Tab. 215. TxSym1_L (address 50h) .............................. 110

Tab. 216. TxSym1_L bits .............................................. 110

Tab. 217. TxSYM2 (address 51h) ................................. 110

Tab. 218. TxSym2 bits .................................................. 110

Tab. 219. TxSym3 (address 52h) ..................................111

Tab. 220. TxSym3 bits .................................................. 111

Tab. 221. TxSym10Len (address 53h) .......................... 111

Tab. 222. TxSym10Len bits ...........................................111

Tab. 223. TxSym32Len (address 54h) .......................... 111

Tab. 224. TxSym32Len bits ...........................................111

Tab. 225. TxSym10BurstCtrl register (address 55h) ..... 112

Tab. 226. TxSym10BurstCtrl bits ...................................112

Tab. 227. TxSym10Mod register (address 56h) ............ 112

Tab. 228. TxSym10Mod bits ..........................................112

Tab. 229. TxSym32Mod register (address 57h) ............ 113

Tab. 230. TxSym32Mod bits ..........................................113

Tab. 231. RxBitMod (address 58h) ............................... 114

Tab. 232. RxBitMod bits ................................................ 114

Tab. 233. RxEofSym (address 59h) .............................. 115

Tab. 234. RxEOFSym bits .............................................115

Tab. 235. RxSyncValH register (address5Ah) ............... 115

Tab. 236. RxSyncValH bits ............................................115

Tab. 237. RxSyncValL register (address 5Bh) ...............115

Tab. 238. RxSyncValL bits ............................................ 116

Tab. 239. RxSyncMode register (address 5Ch) ............ 116

Tab. 240. RxSyncMod bits ............................................ 116

Tab. 241. RxMod register (address 5Dh) ...................... 116

Tab. 242. RxMod bits .................................................... 116

Tab. 243. RxCorr register (address 5Eh) ...................... 117

Tab. 244. RxCorr bits .................................................... 117

Tab. 245. FabCali register (address 5Fh) ......................117

Tab. 246. FabCali bits ................................................... 117

Tab. 247. Version register (address 7Fh) ...................... 118

Tab. 248. Version bits ....................................................118

Tab. 249. Limiting values .............................................. 119

Tab. 250. Operating conditions CLRC66301,

CLRC66302 ...................................................120

Tab. 251. Operating conditions CLRC66303 .................120

Tab. 252. Thermal characteristics ................................. 121

Tab. 253. Thermal characteristics ................................. 121

Tab. 254. Characteristics ...............................................122

Tab. 255. SPI timing characteristics .............................. 125

Tab. 256. I2C-bus timing in fast mode and fast mode

plus ................................................................ 125

Tab. 257. Marking code .................................................136

Tab. 258. Marking code: VFBGA36 .............................. 136

Tab. 259. ISO/IEC14443-A 106 / MIFARE Classic

(Protocol Number 00) ....................................144

Tab. 260. ISO/IEC14443-A 212/ MIFARE Classic

(Protocol Number 01) ....................................145

Tab. 261. ISO/IEC14443-A 424/ MIFARE Classic

(Protocol Number 02) ....................................145

Tab. 262. ISO/IEC14443-A 848/ MIFARE Classic

(Protocol Number 03) ....................................146

Tab. 263. ISO/IEC14443-B 106 Classic (Protocol

Number 04) ................................................... 147

Tab. 264. ISO/IEC14443-B 212 Classic (Protocol

Number 05) ................................................... 148

Tab. 265. ISO/IEC14443-B 424, (Protocol Number

06) ................................................................. 148

Tab. 266. ISO/IEC14443-B 848, (Protocol Number

07) ................................................................. 149

Tab. 267. JIS X 6319-4 (FeliCa) 212, (Protocol

Number 08) ................................................... 150

Tab. 268. JIS X 6319-4 (FeliCa) 424, (Protocol

Number 09) ................................................... 151

Tab. 269. ISO/IEC15693 SLI 1/4 - SSC- 26, (Protocol

Number 10) ................................................... 151

Tab. 270. ISO/IEC15693 SLI 1/4 - SSC- 53, (Protocol

Number 11) ................................................... 152

Tab. 271. SO/IEC15693 SLI 1/256 - DSC, (Protocol

Number 12) ................................................... 153

Tab. 272. EPC/UID - SSC -26, (Protocol Number 13) ...154

Tab. 273. EPC-V2 - 2/424 (Protocol Number 14) .......... 154

Tab. 274. EPC-V2 - 4/424, (Protocol Number 15) ......... 155

Tab. 275. EPC-V2 - 2/848, (Protocol Number 16) ......... 156

Tab. 276. EPC-V2 - 4/848, (Protocol Number 17) ......... 157

Tab. 277. Jewel, (Protocol Number 18) .........................157

Tab. 278. ISO/IEC14443-A 106 / MIFARE Classic ........158

Tab. 279. ISO/IEC14443-A 212/ MIFARE Classic .........159

Tab. 280. ISO/IEC14443-A 424/ MIFARE Classic .........159

Tab. 281. ISO/IEC14443-A 848/ MIFARE Classic .........160

Tab. 282. ISO/IEC14443-B 106 .....................................161

Tab. 283. ISO/IEC14443-B 212 .....................................161

Tab. 284. ISO/IEC14443-B 424 .....................................162

Tab. 285. ISO/IEC14443-B 848 .....................................162

Tab. 286. JIS X 6319-4 (FeliCa) 212 ............................ 163

Tab. 287. JIS X 6319-4 (FeliCa) 424 ............................ 164

Tab. 288. ISO/IEC15693 SLI 1/4 - SSC- 26 ..................164

Tab. 289. ISO/IEC15693 SLI 1/4 - SSC-53 ...................165

Tab. 290. ISO/IEC15693 SLI 1/256 - DSC ....................165

Tab. 291. EPC/UID - SSC -26 ...................................... 166

Tab. 292. EPC-V2 - 2/424 .............................................167

Tab. 293. EPC-V2 - 4/424 .............................................167

Tab. 294. EPC-V2 - 2/848 .............................................168

Tab. 295. EPC-V2 - 4/848 .............................................168

Tab. 296. Jewel ............................................................. 169

Tab. 297. ISO/IEC14443 - B 106 EMVCo Optimized .... 169

Tab. 298. Abbreviations .................................................171

Tab. 299. Revision history ............................................. 174

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 179 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Figures

Fig. 1. Simplified block diagram of the CLRC663 .........7

Fig. 2. Pinning configuration HVQFN32

(SOT617-1) ........................................................8

Fig. 3. Detailed block diagram of the CLRC663 ......... 11

Fig. 4. Read/write mode ............................................. 15

Fig. 5. Read/write mode for ISO/IEC 14443 type A

and read/write mode for MIFARE Classic ........15

Fig. 6. Data coding and framing according to ISO/

IEC 14443 A ................................................... 16

Fig. 7. ISO/IEC 14443 type B communication

diagram ............................................................16

Fig. 8. SOF and EOF according to ISO/IEC 14443

B ...................................................................... 17

Fig. 9. FeliCa read/write communication diagram ...... 17

Fig. 10. Data coding according to ISO/IEC 15693.

standard mode reader to label ........................ 19

Fig. 11. Passive communication mode .........................21

Fig. 12. Connection to host with SPI ............................22

Fig. 13. Connection to host with SPI ............................24

Fig. 14. Example for UART Read ................................ 26

Fig. 15. Example diagram for a UART write .................27

Fig. 16. I2C-bus interface ............................................. 27

Fig. 17. Bit transfer on the I2C-bus ..............................28

Fig. 18. START and STOP conditions ..........................28

Fig. 19. Acknowledge on the I2C- bus ......................... 29

Fig. 20. Data transfer on the I2C- bus ......................... 29

Fig. 21. First byte following the START procedure ....... 30

Fig. 22. Register read and write access .......................31

Fig. 23. I2C interface enables convenient MIFARE

SAM integration ...............................................33

Fig. 24. Boundary scan cell path structure ...................35

Fig. 25. General dependences of modulation .............. 39

Fig. 26. Example 1: overshoot_t1 = 2d; overhoot_t2

= 5d. ................................................................ 41

Fig. 27. Example 2: overshoot_t1 = 0d; overhoot_t2

= 5d ................................................................. 42

Fig. 28. Block diagram of receiver circuitry .................. 43

Fig. 29. Block diagram of the active Antenna

concept ............................................................ 44

Fig. 30. Overview SIGIN/SIGOUT Signal Routing ........45

Fig. 31. Sector arrangement of the EEPROM .............. 47

Fig. 32. Crystal connection ...........................................51

Fig. 33. Internal PDown to voltage regulator logic ........55

Fig. 34. Pin RX input voltage ..................................... 125

Fig. 35. Timing for fast and standard mode devices

on the I2C-bus .............................................. 126

Fig. 36. Typical application antenna circuit diagram ... 127

Fig. 37. Package outline SOT-617-1 (HVQFN32) ...... 130

Fig. 38. VFBGA36 Package outline ............................131

Fig. 39. VFBGA36 Package outline notes ..................132

Fig. 40. VFBGA36 PCB design: Solder mask

opening pattern ............................................. 133

Fig. 41. VFBGA36 PCB design: I/O pads and

solderable area ............................................. 134

Fig. 42. VFBGA36 PCB design: Solder paste

stencil ............................................................ 135

Fig. 43. HVQFN32 Package marking ......................... 136

Fig. 44. VFBGA36 Package marking ......................... 137

Fig. 45. Packing information 1 tray .............................139

Fig. 46. Packing information 5 tray .............................140

Fig. 47. Tray details ....................................................141

Fig. 48. Packing information Reel .............................. 142

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 180 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

Contents

1 General description ............................................ 1

2 Features and benefits .........................................3

3 Applications .........................................................4

4 Quick reference data .......................................... 5

5 Ordering information .......................................... 6

6 Block diagram ..................................................... 7

7 Pinning information ............................................ 8

7.1 Pin description HVQFN32 ................................. 8

7.2 Pin description VFBGA36 ..................................9

8 Functional description ......................................11

8.1 Interrupt controller ............................................11

8.2 Timer module ...................................................13

8.2.1 Timer modes ....................................................14

8.2.1.1 Time-Out- and Watch-Dog-Counter ................. 14

8.2.1.2 Wake-up timer ................................................. 14

8.2.1.3 Stop watch .......................................................14

8.2.1.4 Programmable one-shot timer ......................... 14

8.2.1.5 Periodical trigger ..............................................14

8.3 Contactless interface unit ................................ 15

8.3.1 Communication mode for ISO/IEC 14443

type A and for MIFARE Classic ....................... 15

8.3.2 ISO/IEC14443 type B functionality .................. 16

8.3.3 FeliCa functionality .......................................... 17

8.3.3.1 FeliCa framing and coding .............................. 18

8.3.4 ISO/IEC15693 functionality ..............................18

8.3.5 EPC-UID/UID-OTP functionality ...................... 19

8.3.6 ISO/IEC 18000-3 mode 3/ EPC Class-1 HF

functionality ...................................................... 20

8.3.6.1 Data encoding ICODE ..................................... 20

8.3.7 ISO/IEC 18092 mode ...................................... 20

8.3.7.1 Passive communication mode ......................... 20

8.3.7.2 ISO/IEC 18092 framing and coding ................. 21

8.3.7.3 ISO/IEC 18092 protocol support ......................21

8.4 Host interfaces .................................................22

8.4.1 Host interface configuration ............................. 22

8.4.2 SPI interface .................................................... 22

8.4.2.1 General ............................................................ 22

8.4.2.2 Read data ........................................................23

8.4.2.3 Write data ........................................................ 23

8.4.2.4 Address byte ....................................................23

8.4.2.5 Timing Specification SPI ..................................24

8.4.3 RS232 interface ...............................................24

8.4.3.1 Selection of the transfer speeds ...................... 24

8.4.3.2 Framing ............................................................25

8.4.4 I2C-bus interface ............................................. 27

8.4.4.1 General ............................................................ 27

8.4.4.2 I2C Data validity .............................................. 28

8.4.4.3 I2C START and STOP conditions ....................28

8.4.4.4 I2C byte format ................................................28

8.4.4.5 I2C Acknowledge .............................................29

8.4.4.6 I2C 7-bit addressing ........................................ 29

8.4.4.7 I2C-register write access ................................. 30

8.4.4.8 I2C-register read access ................................. 30

8.4.4.9 I2CL-bus interface ........................................... 31

8.4.5 SAM interface .................................................. 32

8.4.5.1 SAM functionality ............................................. 32

8.4.5.2 SAM connection .............................................. 33

8.4.6 Boundary scan interface ..................................33

8.4.6.1 Interface signals .............................................. 34

8.4.6.2 Test Clock (TCK) ............................................. 34

8.4.6.3 Test Mode Select (TMS) ..................................34

8.4.6.4 Test Data Input (TDI) ....................................... 35

8.4.6.5 Test Data Output (TDO) .................................. 35

8.4.6.6 Data register .................................................... 35

8.4.6.7 Boundary scan cell .......................................... 35

8.4.6.8 Boundary scan path ........................................ 35

8.4.6.9 Boundary Scan Description Language

(BSDL) ............................................................. 36

8.4.6.10 Non-IEEE1149.1 commands ............................37

8.5 Buffer ............................................................... 37

8.5.1 Overview .......................................................... 37

8.5.2 Accessing the FIFO buffer ...............................37

8.5.3 Controlling the FIFO buffer .............................. 37

8.5.4 Status Information about the FIFO buffer .........38

8.6 Analog interface and contactless UART .......... 39

8.6.1 General ............................................................ 39

8.6.2 TX transmitter .................................................. 39

8.6.2.1 Overshoot protection ....................................... 41

8.6.2.2 Bit generator .................................................... 42

8.6.3 Receiver circuitry ............................................. 42

8.6.3.1 General ............................................................ 42

8.6.3.2 Block diagram ..................................................42

8.6.4 Active antenna concept ................................... 43

8.6.5 Symbol generator ............................................ 46

8.7 Memory ............................................................ 46

8.7.1 Memory overview .............................................46

8.7.2 EEPROM memory organization .......................46

8.7.2.1 Product information and configuration -

Page 0 ............................................................. 47

8.7.3 EEPROM initialization content

LoadProtocol ....................................................49

8.8 Clock generation ..............................................51

8.8.1 Crystal oscillator .............................................. 51

8.8.2 IntegerN PLL clock line ................................... 52

8.8.3 Low Frequency Oscillator (LFO) ......................52

8.9 Power management .........................................53

8.9.1 Supply concept ................................................ 53

8.9.2 Power reduction mode .....................................53

8.9.2.1 Power-down ..................................................... 53

8.9.2.2 Standby mode ................................................. 54

8.9.2.3 Modem off mode ............................................. 54

8.9.3 Low-Power Card Detection (LPCD) .................54

8.9.4 Reset and start-up time ................................... 54

8.10 Command set .................................................. 55

8.10.1 General ............................................................ 55

8.10.2 Command set overview ................................... 55

8.10.3 Command functionality .................................... 56

8.10.3.1 Idle command .................................................. 56

8.10.3.2 LPCD command .............................................. 56

8.10.3.3 Load key command ......................................... 56

8.10.3.4 MFAuthent command .......................................57

8.10.3.5 AckReq command ........................................... 57

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 181 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

8.10.3.6 Receive command ........................................... 57

8.10.3.7 Transmit command .......................................... 57

8.10.3.8 Transceive command .......................................58

8.10.3.9 WriteE2 command ........................................... 58

8.10.3.10 WriteE2PAGE command ..................................58

8.10.3.11 ReadE2 command ........................................... 58

8.10.3.12 LoadReg command ......................................... 58

8.10.3.13 LoadProtocol command ...................................58

8.10.3.14 LoadKeyE2 command ..................................... 60

8.10.3.15 StoreKeyE2 command .....................................60

8.10.3.16 GetRNR command .......................................... 60

8.10.3.17 SoftReset command ........................................ 61

9 CLRC663 registers ............................................62

9.1 Register bit behavior ....................................... 62

9.2 Command configuration ...................................65

9.2.1 Command ........................................................ 65

9.3 SAM configuration register .............................. 65

9.3.1 HostCtrl ............................................................ 65

9.4 FIFO configuration register .............................. 66

9.4.1 FIFOControl ..................................................... 66

9.4.2 WaterLevel ....................................................... 67

9.4.3 FIFOLength ......................................................68

9.4.4 FIFOData ......................................................... 68

9.5 Interrupt configuration registers ....................... 68

9.5.1 IRQ0 register ................................................... 69

9.5.2 IRQ1 register ................................................... 69

9.5.3 IRQ0En register ...............................................70

9.5.4 IRQ1En ............................................................ 70

9.6 Contactless interface configuration

registers ........................................................... 71

9.6.1 Error ................................................................. 71

9.6.2 Status ...............................................................72

9.6.3 RxBitCtrl ...........................................................73

9.6.4 RxColl .............................................................. 74

9.7 Timer configuration registers ........................... 74

9.7.1 TControl ........................................................... 74

9.7.2 T0Control ......................................................... 75

9.7.2.1 T0ReloadHi ...................................................... 76

9.7.2.2 T0ReloadLo ..................................................... 76

9.7.2.3 T0CounterValHi ................................................77

9.7.2.4 T0CounterValLo ............................................... 77

9.7.2.5 T1Control ......................................................... 77

9.7.2.6 T1ReloadHi ...................................................... 78

9.7.2.7 T1ReloadLo ..................................................... 78

9.7.2.8 T1CounterValHi ................................................79

9.7.2.9 T1CounterValLo ............................................... 79

9.7.2.10 T2Control ......................................................... 79

9.7.2.11 T2ReloadHi ...................................................... 80

9.7.2.12 T2ReloadLo ..................................................... 80

9.7.2.13 T2CounterValHi ................................................81

9.7.2.14 T2CounterValLoReg ........................................ 81

9.7.2.15 T3Control ......................................................... 81

9.7.2.16 T3ReloadHi ...................................................... 82

9.7.2.17 T3ReloadLo ..................................................... 82

9.7.2.18 T3CounterValHi ................................................83

9.7.2.19 T3CounterValLo ............................................... 83

9.7.2.20 T4Control ......................................................... 83

9.7.2.21 T4ReloadHi ...................................................... 84

9.7.2.22 T4ReloadLo ..................................................... 85

9.7.2.23 T4CounterValHi ................................................85

9.7.2.24 T4CounterValLo ............................................... 85

9.8 Transmitter driver configuration registers .........86

9.8.1 DrvMode .......................................................... 86

9.8.2 TxAmp ..............................................................86

9.8.3 TxCon .............................................................. 87

9.8.4 Txl .................................................................... 87

9.9 Transmitter CRC configuration registers ..........88

9.9.1 TxCrcPreset ..................................................... 88

9.9.2 RxCrcCon ........................................................ 89

9.10 Transmitter data configuration registers ...........89

9.10.1 TxDataNum ......................................................90

9.10.2 TxDATAModWidth ............................................90

9.10.3 TxSym10BurstLen ........................................... 91

9.10.4 TxWaitCtrl ........................................................ 91

9.10.5 TxWaitLo .......................................................... 92

9.11 FrameCon ........................................................ 92

9.12 Receiver configuration registers ...................... 93

9.12.1 RxSofD .............................................................93

9.12.2 RxCtrl ............................................................... 93

9.12.3 RxWait ............................................................. 94

9.12.4 RxThreshold .....................................................95

9.12.5 Rcv ...................................................................95

9.12.6 RxAna .............................................................. 96

9.13 Clock configuration .......................................... 97

9.13.1 SerialSpeed ..................................................... 97

9.13.2 LFO_Trimm ...................................................... 98

9.13.3 PLL_Ctrl Register ............................................ 98

9.13.4 PLLDiv_Out ......................................................99

9.14 Low-power card detection configuration

registers ......................................................... 100

9.14.1 LPCD_QMin ...................................................100

9.14.2 LPCD_QMax ..................................................100

9.14.3 LPCD_IMin .....................................................101

9.14.4 LPCD_Result_I .............................................. 101

9.14.5 LPCD_Result_Q ............................................ 102

9.14.6 LPCD_Options ............................................... 102

9.15 Pin configuration ............................................103

9.15.1 PadEn ............................................................ 103

9.15.2 PadOut ...........................................................104

9.15.3 PadIn ..............................................................104

9.15.4 SigOut ............................................................ 105

9.16 Protocol configuration registers ..................... 106

9.16.1 TxBitMod ........................................................106

9.16.2 TxDataCon .....................................................106

9.16.3 TxDataMod .................................................... 107

9.16.4 TxSymFreq .................................................... 108

9.16.5 TxSym0 ..........................................................109

9.16.6 TxSym1 ..........................................................110

9.16.7 TxSym2 ..........................................................110

9.16.8 TxSym3 ..........................................................111

9.16.9 TxSym10Len ..................................................111

9.16.10 TxSym32Len ..................................................111

9.16.11 TxSym10BurstCtrl ..........................................112

9.16.12 TxSym10Mod Reg ......................................... 112

9.16.13 TxSym32Mod .................................................113

9.17 Receiver configuration ................................... 114

9.17.1 RxBitMod ....................................................... 114

9.17.2 RxEofSym ...................................................... 115

Product data sheet Rev. 5.0 — 27 November 2020

COMPANY PUBLIC 171150 182 / 183

NXP Semiconductors CLRC663

High performance multi-protocol NFC frontend CLRC663 and CLRC663 plus

9.17.3 RxSyncValH ................................................... 115

9.17.4 RxSyncValL ....................................................115

9.17.5 RxSyncMod ....................................................116

9.17.6 RxMod ............................................................116

9.17.7 RxCorr ............................................................117

9.17.8 FabCali ...........................................................117

9.18 Version register ..............................................118

9.18.1 Version ........................................................... 118

10 Limiting values ................................................ 119

11 Recommended operating conditions ............ 120

12 Thermal characteristics ..................................121

12.1 Thermal characteristics HVQFN32 ................ 121

12.2 Thermal characteristics VFBGA36 .................121

13 Characteristics ................................................ 122

13.1 Timing characteristics .................................... 125

14 Application information ..................................127

14.1 Antenna design description ........................... 127

14.1.1 EMC low pass filter ....................................... 127

14.1.2 Antenna matching ..........................................128

14.1.3 Receiving circuit .............................................128

14.1.4 Antenna coil ...................................................128

15 Package outline ...............................................130

15.1 Package outline HVQFN32 ............................130

15.2 Package outline and PCB design

information VFBGA36 ....................................131

16 Marking .............................................................136

16.1 Marking HVQFN32 ........................................ 136

16.2 Marking VFBGA36 .........................................136

17 Handling information ...................................... 138

18 Packing information ........................................139

19 Appendix .......................................................... 144

19.1 LoadProtocol command register

initialization .................................................... 144

19.2 CLRC66303 EEPROM configuration ............. 158

20 Abbreviations .................................................. 171

21 References ....................................................... 173

22 Revision history .............................................. 174

23 Legal information ............................................ 175

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section 'Legal information'.

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 27 November 2020

Document identifier: CLRC663

Document number: 171150