MC14043B, MC14044B CMOS MSI Quad R-S Latches The MC14043B and MC14044B quad R-S latches are constructed with MOS P-Channel and N-Channel enhancement mode devices in a single monolithic structure. Each latch has an independent Q output and set and reset inputs. The Q outputs are gated through three-state buffers having a common enable input. The outputs are enabled with a logical "1" or high on the enable input; a logical "0" or low disconnects the latch from the Q outputs, resulting in an open circuit at the Q outputs. http://onsemi.com MARKING DIAGRAMS PDIP-16 P SUFFIX CASE 648 Features * Double Diode Input Protection * Three-State Outputs with Common Enable * Outputs Capable of Driving Two Low-power TTL Loads or One * * 16 Unit -0.5 to +18.0 V -0.5 to VDD + 0.5 V Input or Output Current (DC or Transient) per Pin 10 mA PD Power Dissipation, per Package (Note 1) 500 mW Vin, Vout Iin, Iout DC Supply Voltage Range Input or Output Voltage Range (DC or Transient) 140xxBG AWLYWW 1 Value VDD 1 SOIC-16 D SUFFIX CASE 751B MAXIMUM RATINGS (Voltages Referenced to VSS) Parameter MC140xxBCP AWLYYWWG 16 Low-Power Schottky TTL Load Over the Rated Temperature Range Supply Voltage Range = 3.0 Vdc to 18 Vdc These Devices are Pb-Free and are RoHS Compliant Symbol 16 TA Ambient Temperature Range -55 to +125 C Tstg Storage Temperature Range -65 to +150 C TL Lead Temperature (8-Second Soldering) 260 C Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. Temperature Derating: Plastic "P and D/DW" Packages: - 7.0 mW/_C From 65_C To 125_C SOEIAJ-16 F SUFFIX CASE 966 MC14043B ALYWG 1 xx A WL, L YY, Y WW, W G = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Indicator ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range VSS v (Vin or Vout) v VDD. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS or VDD). Unused outputs must be left open. (c) Semiconductor Components Industries, LLC, 2011 June, 2011 - Rev. 7 1 Publication Order Number: MC14043B/D MC14043B, MC14044B PIN ASSIGNMENT MC14043B MC14044B Q3 1 16 VDD Q3 1 16 VDD Q0 2 15 R3 NC 2 15 S3 R0 3 14 S3 S0 3 14 R3 S0 4 13 NC R0 4 13 Q0 E 5 12 S2 E 5 12 R2 S1 6 11 R2 R1 6 11 S2 R1 7 10 Q2 S1 7 10 Q2 VSS 8 9 Q1 VSS 8 9 Q1 NC = NO CONNECTION MC14043B S0 R0 S1 R1 S2 R2 S3 4 MC14044B 2 R0 Q0 3 S0 6 9 R1 Q1 7 12 VDD = PIN 16 VSS = PIN 8 NC = PIN 13 10 S1 R2 Q2 11 S2 14 TRUTH TABLE 1 Q3 S R E Q X X 0 High Impedance 15 R3 5 ENABLE 0 0 1 1 0 1 0 1 R3 4 13 Q0 3 6 9 Q1 7 12 VDD = PIN 16 VSS = PIN 8 NC = PIN 2 10 Q2 11 14 TRUTH TABLE 1 Q3 S R E Q X X 0 High Impedance 15 1 No Change 1 0 1 1 1 1 S3 5 ENABLE X = Don't Care http://onsemi.com 2 0 0 1 1 0 1 0 1 1 0 1 1 1 0 1 No Change X = Don't Care MC14043B, MC14044B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIII IIIIIIIII IIIII IIII IIIIIIIIIIIII IIIIII IIIIIIIIIIIIII IIIIIII IIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIIIIIIIIIIII IIIIIII IIIIII IIIIII IIIIIII IIIIIII IIIIIII IIIIIII IIIIII IIIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII III IIII III IIII III III III IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIII III IIIIIIIIIIIIIIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII III IIIIIIIIIIIIIIIII IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS) Characteristic Output Voltage Vin = VDD or 0 Symbol - 55_C 25_C 125_C VDD Vdc Min Max Min Typ (Note 2) Max Min Max Unit "0" Level VOL 5.0 10 15 - - - 0.05 0.05 0.05 - - - 0 0 0 0.05 0.05 0.05 - - - 0.05 0.05 0.05 Vdc "1" Level VOH 5.0 10 15 4.95 9.95 14.95 - - - 4.95 9.95 14.95 5.0 10 15 - - - 4.95 9.95 14.95 - - - Vdc Input Voltage "0" Level (VO = 4.5 or 0.5 Vdc) (VO = 9.0 or 1.0 Vdc) (VO = 13.5 or 1.5 Vdc) VIL 5.0 10 15 - - - 1.5 3.0 4.0 - - - 2.25 4.50 6.75 1.5 3.0 4.0 - - - 1.5 3.0 4.0 "1" Level VIH 5.0 10 15 3.5 7.0 11 - - - 3.5 7.0 11 2.75 5.50 8.25 - - - 3.5 7.0 11 - - - 5.0 5.0 10 15 - 3.0 - 0.64 - 1.6 - 4.2 - - - - - 2.4 - 0.51 - 1.3 - 3.4 - 4.2 - 0.88 - 2.25 - 8.8 - - - - - 1.7 - 0.36 - 0.9 - 2.4 - - - - IOL 5.0 10 15 0.64 1.6 4.2 - - - 0.51 1.3 3.4 0.88 2.25 8.8 - - - 0.36 0.9 2.4 - - - mAdc Input Current Iin 15 - 0.1 - 0.00001 0.1 - 1.0 mAdc Input Capacitance (Vin = 0) Cin - - - - 5.0 7.5 - - pF Quiescent Current (Per Package) IDD 5.0 10 15 - - - 1.0 2.0 4.0 - - - 0.002 0.004 0.006 1.0 2.0 4.0 - - - 30 60 120 mAdc Total Supply Current (Notes 3 & 4) (Dynamic plus Quiescent, Per Package) (CL = 50 pF on all outputs all buffers switching) IT 5.0 10 15 Three-State Output Leakage Current ITL 15 Vin = 0 or VDD (VO = 0.5 or 4.5 Vdc) (VO = 1.0 or 9.0 Vdc) (VO = 1.5 or 13.5 Vdc) Output Drive Current (VOH = 2.5 Vdc) (VOH = 4.6 Vdc) (VOH = 9.5 Vdc) (VOH = 13.5 Vdc) Source (VOL = 0.4 Vdc) (VOL = 0.5 Vdc) (VOL = 1.5 Vdc) Sink IOH Vdc Vdc mAdc IT = (0.58 mA/kHz) f + IDD IT = (1.15 mA/kHz) f + IDD IT = (1.73 mA/kHz) f + IDD - 0.1 - 0.0001 0.1 mAdc - 3.0 2. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. 3. The formulas given are for the typical characteristics only at 25_C. 4. To calculate total supply current at loads other than 50 pF: IT(CL) = IT(50 pF) + (CL - 50) Vfk where: IT is in mA (per package), CL in pF, V = (VDD - VSS) in volts, f in kHz is input frequency, and k = 0.004. http://onsemi.com 3 mAdc MC14043B, MC14044B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII SWITCHING CHARACTERISTICS (Note 5) (CL = 50 pF, TA = 25_C) Characteristic Symbol VDD Vdc Min Typ (Note 6) Max 5.0 10 15 - - - 100 50 40 200 100 80 5.0 10 15 - - - 100 50 40 200 100 80 5.0 10 15 - - - 175 75 60 350 175 120 Unit Output Rise Time tTLH = (1.35 ns/pF) CL + 32.5 ns tTLH = (0.60 ns/pF) CL + 20 ns tTLH = (0.40 ns/pF) CL + 20 ns tTLH Output Fall Time tTHL = (1.35 ns/pF) CL + 32.5 ns tTHL = (0.60 ns/pF) CL + 20 ns tTHL = (0.40 ns/pF) CL + 20 ns tTHL Propagation Delay Time tPLH = (0.90 ns/pF) CL + 130 ns tPLH = (0.36 ns/pF) CL + 57 ns tPLH = (0.26 ns/pF) CL + 47 ns tPLH tPHL = (0.90 ns/pF) CL + 130 ns tPHL = (0.90 ns/pF) CL + 57 ns tPHL = (0.26 ns/pF) CL + 47 ns tPHL 5.0 10 15 - - - 175 75 60 350 175 120 ns Set, Set Pulse Width tW 5.0 10 15 200 100 70 80 40 30 - - - ns Reset, Reset Pulse Width tW 5.0 10 15 200 100 70 80 40 30 - - - ns tPLZ, tPHZ, tPZL, tPZH 5.0 10 15 - - - 150 80 55 300 160 110 ns Three-State Enable/Disable Delay ns ns ns 5. The formulas given are for the typical characteristics only at 25_C. 6. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. AC WAVEFORMS MC14043B MC14044B 20 ns 50% 10% 20 ns 50% tPHL VDD 90% 10% VSS 20 ns 90% VDD VDD 10% 10% 50% 20 ns 90% tTHL Q SET VSS 20 ns RESET 20 ns VDD 90% SET 20 ns 20 ns 50% RESET VSS tTLH tTHL tTLH VOH 90% 50% 10% Q 50% VOL 90% 10% tPLH tPLH http://onsemi.com 4 tPHL VSS VOH VOL MC14043B, MC14044B THREE-STATE ENABLE/DISABLE DELAYS Set, Reset, Enable, and Switch Conditions for 3-State Tests MC14043B VDD MC14044B S1 S2 Q S R S R tPZH Open Closed A VDD VSS VSS VDD tPZL Closed Open B VSS VDD VDD VSS tPHZ Open Closed A VDD VSS VSS VDD tPLZ Closed Open B VSS VDD VDD VSS Test Enable S1 TO OUTPUT UNDER TEST 1k CL 50 pF S2 VSS VDD ENABLE 50% VSS tPZH VDD 90% QA 10% tPZL tPHZ VOL tPLZ VOH QB 10% VSS ORDERING INFORMATION Package Shipping MC14043BCPG PDIP-16 (Pb-Free) 500 Units / Rail MC14043BDG SOIC-16 (Pb-Free) 48 Units / Rail MC14043BDR2G SOIC-16 (Pb-Free) 2500 Units / Tape & Reel MC14043BFELG SOEIAJ-16 2000 Units / Tape & Reel MC14044BCPG PDIP-16 (Pb-Free) 500 Units / Rail MC14044BDG SOIC-16 (Pb-Free) 48 Units / Rail MC14044BDR2G SOIC-16 (Pb-Free) 2500 Units / Tape & Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 5 MC14043B, MC14044B PACKAGE DIMENSIONS PDIP-16 P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE T NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. -A- 16 9 1 8 B F C L DIM A B C D F G H J K L M S S -T- SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M T A M INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 SOEIAJ-16 F SUFFIX PLASTIC EIAJ SOIC PACKAGE CASE 966-01 ISSUE A 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 9 Q1 E HE 1 M_ L 8 Z DETAIL P D e VIEW P A A1 b 0.13 (0.005) c M 0.10 (0.004) http://onsemi.com 6 DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.10 0.20 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --0.78 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --0.031 MC14043B, MC14044B PACKAGE DIMENSIONS SOIC-16 D SUFFIX PLASTIC SOIC PACKAGE CASE 751B-05 ISSUE K -A- 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 -B- 1 P 8 PL 0.25 (0.010) 8 M B S G R K F X 45 _ C -T- SEATING PLANE J M D DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 16 PL 0.25 (0.010) M T B S A S SOLDERING FOOTPRINT 8X 6.40 16X 1 1.12 16 16X 0.58 1.27 PITCH 8 9 DIMENSIONS: MILLIMETERS ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 7 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC14043B/D