MAX6412-MAX6420 Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay General Description The MAX6412-MAX6420 low-power microprocessor supervisor circuits monitor system voltages from 1.6V to 5V. These devices are designed to assert a reset signal whenever the VCC supply voltage or RESET IN falls below its reset threshold or the manual reset input is asserted. The reset output remains asserted for the reset timeout period after VCC and RESET IN rise above the reset threshold and the manual reset input is deasserted. The reset timeout is externally set by a capacitor to provide more flexibility. The MAX6412/MAX6413/MAX6414 feature fixed thresholds from 1.575V to 5V in approximately 100mV increments and a manual reset input. The MAX6415/MAX6416/ MAX6417 are offered with an adjustable reset input that can monitor voltages down to 1.26V and the MAX6418/ MAX6419/MAX6420 are offered with one fixed input and one adjustable input to monitor dual-voltage systems. The MAX6412/MAX6415/MAX6418 have an activelow, push-pull reset output. The MAX6413/MAX6416/ MAX6419 have an active-high, push-pull reset output and the MAX6414/MAX6417/MAX6420 have an active-low, open-drain reset output. All of these devices are offered in a SOT23-5 package and are fully specified from -40C to +125C. TOP VIEW RESET/RESET 1 5 VCC 4 SRT MAX6412 MAX6420 RESET IN (MR) 3 SOT23-5 ( ) FOR THE MAX6412/MAX6413/MAX6414. 19-2336; Rev 7; 12/15 Monitor System Voltages from 1.6V to 5V Capacitor-Adjustable Reset Timeout Period Manual Reset Input (MAX6412/MAX6413/MAX6414) Adjustable Reset Input Option (MAX6415-MAX6420) Dual-Voltage Monitoring (MAX6418/MAX6419/MAX6420) Low Quiescent Current (1.7A, typ) 3 * * * RESET Output Options Push-Pull RESET Push-Pull RESET Open-Drain RESET Guaranteed Reset Valid to VCC = 1V Power-Supply Transient Immunity Small SOT23-5 Packages Applications Automotive Medical Equipment Intelligent Instruments Portable Equipment Battery-Powered Computers/Controllers Embedded Controllers Critical P Monitoring Set-Top Boxes Computers Selector Guide, Ordering Information, and Typical Operating Circuit appear at end of data sheet. Pin Configuration GND 2 Benefits and Features MAX6412-MAX6420 Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Absolute Maximum Ratings All Voltages Referenced to GND VCC........................................................................-0.3V to +6.0V SRT, MR, RESET IN................................. -0.3V to (VCC + 0.3V) RESET, RESET (Push-Pull)...................... -0.3V to (VCC + 0.3V) RESET (Open-Drain)............................................-0.3V to +6.0V Input Current (All Pins)......................................................20mA Output Current (RESET, RESET).....................................20mA Continuous Power Dissipation (TA = +70C) 5-Pin SOT23 (derate 7.1mW/C above +70C)...........571mW Operating Temperature Range.......................... -40C to +125C Junction Temperature.......................................................+150C Storage Temperature Range............................. -65C to +150C Lead Temperature (soldering, 10s).................................. +300C Soldering Temperature (reflow) Lead(Pb)-free packages...............................................+260C Packages containing lead (Pb).....................................+240C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics (VCC = 1V to 5.5V, TA = TMIN to TMAX, unless otherwise specified. Typical values are at VCC = 5V and TA = +25C.) (Note 1) PARAMETER SYMBOL Supply Voltage Range VCC Supply Current ICC VCC Reset Threshold Accuracy Hysteresis VTH tRD Reset Timeout Period tRP VSRT Ramp Threshold RAMP Threshold Hysteresis RESET Output Voltage LOW MIN IRAMP TYP 1.0 VOH RESET Output Leakage Current, (Open-Drain) ILKG RESET Output Voltage HIGH www.maximintegrated.com VOH 5.5 V 2.6 4.5 2 3.5 VCC 2.0V 1.7 2.5 TA = +25C VTH 1.25% VTH + 1.25% TA = -40C to +125C VTH 2.5% VTH + 2.5% V mV 100 s VCC falling at 1mV/s CSRT = 1500pF A 4 x VTH 3.00 CSRT = 0F 4.375 5.75 0.275 VSRT = 0 to 0.65V; VCC = 1.6V to 5V ms 240 nA 0.65 V 33 mV VCC 1.0V, ISINK = 50A 0.3 VCC 2.7V, ISINK = 1.2mA 0.3 VCC 4.5V, ISINK = 3.2mA RESET Output Voltage HIGH, (Push-Pull) UNITS VCC 3.3V VTH-RAMP VCC = 1.6V to 5V (VRAMP rising) VRAMP falling threshold VOL MAX VCC 5.0V VHYST VCC to Reset Delay VSRT Ramp Current CONDITIONS V 0.4 VCC 1.8V, ISOURCE = 200A 0.8 x VCC VCC 2.25V, ISOURCE = 500A 0.8 x VCC VCC 4.5V, ISOURCE = 800A 0.8 x VCC VCC > VTH, reset not asserted V 1.0 VCC 1.0V, ISOURCE = 1A 0.8 x VCC VCC 1.8V, ISOURCE = 150A 0.8 x VCC VCC 2.7V, ISOURCE = 500A 0.8 x VCC VCC 4.5V, ISOURCE = 800A 0.8 x VCC A V Maxim Integrated 2 MAX6412-MAX6420 Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Electrical Characteristics (continued) (VCC = 1V to 5.5V, TA = TMIN to TMAX, unless otherwise specified. Typical values are at VCC = 5V and TA = +25C.) (Note 1) PARAMETER SYMBOL RESET Output Voltage LOW VOL VRST VIL TYP MAX 0.3 VCC 4.5V, ISINK = 3.2mA 0.4 VIL V 10 VRST falling, VCC = 1.6V to 5.0V 1.205 nA 1.255 V 0.8 2.4 V 0.3 x VCC VCC < 4.0V VIH UNITS 0.3 VCC > 4.0V VIH MR Input MIN VCC 2.7V, ISINK = 1.2mA RESET IN Leakage Current RESET IN Threshold CONDITIONS VCC 1.8V, ISINK = 500A 0.7 x VCC MR Minimum Pulse Width 1 s MR Glitch Rejection 75 ns MR to RESET Delay 20 ns MR Pullup Resistance Pull up to VCC 12 20 28 k Note 1: Devices production tested at TA = +25C. Over temperature limits are guaranteed by design. Typical Operating Characteristics (VCC = 5V, CSRT = 1500pF, TA = +25C, unless otherwise noted.) TA = +25C 2 TA = -40C 1 3.0 MAX6412-20 toc02 TA = +125C 3 3.5 SUPPLY CURRENT (A) MAX6412-20 toc01 SUPPLY CURRENT (A) 4 VCC = 5V 2.5 VCC = 3.3V 2.0 VCC = 1.8V 1.5 1.0 VCC = 1V 0.5 0 0 1 2 3 4 SUPPLY VOLTAGE (V) www.maximintegrated.com 5 6 0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 10,000 RESET TIMEOUT PERIOD vs. CSRT MAX6412-20 toc03 SUPPLY CURRENT vs. TEMPERATURE RESET TIMEOUT PERIOD (ms) SUPPLY CURRENT vs. SUPPLY VOLTAGE 1000 100 10 1 0.1 0.001 0.01 0.1 1 10 100 1000 CSRT (nF) Maxim Integrated 3 MAX6412-MAX6420 Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Typical Operating Characteristics (continued) (VCC = 5V, CSRT = 1500pF, TA = +25C, unless otherwise noted.) 4.20 4.15 4.10 500 450 400 350 300 250 -50 200 TEMPERATURE (C) 25 75 50 TEMPERATURE (C) RESET IN THRESHOLD VOLTAGE vs. TEMPERATURE MAXIMUM TRANSIENT DURATION vs. RESET THRESHOLD OVERDRIVE -25 0 25 50 75 100 125 MAX6412-20 toc06 1.280 RESET IN THRESHOLD VOLTAGE (V) CSRT = 0 550 1.275 1.270 1.265 1.260 175 25 50 75 www.maximintegrated.com 100 125 125 RESET OCCURS ABOVE THE CURVE 75 50 0 TEMPERATURE (C) 100 100 1.250 0 0 125 25 -25 -25 150 1.255 -50 -50 MAX6412-20 toc07 4.05 MAX6412-20 toc05 4.25 RESET TIMEOUT PERIOD vs. TEMPERATURE 600 RESET TIMEOUT PERIOD (s) CSRT = 1500pF TRANSIENT DURATION (s) RESET TIMEOUT PERIOD (ms) 4.30 MAX6412-20 toc04 RESET TIMEOUT PERIOD vs. TEMPERATURE VTH = 3.0V 0 200 400 600 800 1000 RESET THRESHOLD OVERDRIVE (mV) Maxim Integrated 4 MAX6412-MAX6420 Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Pin Description PIN MAX6412/ MAX6413/ MAX6414 MAX6415/ MAX6416/ MAX6417 1 MAX6418/ MAX6419/ MAX6420 1 NAME FUNCTION RESET RESET changes from high to low whenever VCC or RESET IN drops below the selected reset threshold voltage (VTH or VRESET IN, respectively) or manual reset is pulled low. RESET remains low for the reset timeout period after all reset conditions are deasserted and then goes high. RESET RESET changes from low to high whenever the VCC or RESET IN drops below the selected reset threshold voltage (VTH or VRESET IN) or manual reset is pulled low. RESET remains high for the reset timeout period after all reset conditions are deasserted and then goes low. 1 2 2 2 GND Ground -- 3 3 RESET IN 3 -- -- MR Manual Reset Input. Pull this pin low to manually reset the device. Reset remains asserted for the reset timeout period after MR is released. 4 4 4 SRT Set Reset Timeout Input. Connect a capacitor between SRT and ground to set the timeout period. Determine the period as follows: tRP = (2.71 x 106) x CSRT + 275s with tRP in seconds and CSRT in Farads. 5 5 5 VCC Supply Voltage and Input for Fixed-Threshold VCC Monitor Reset Input. High-impedance input to the adjustable reset comparator. Connect RESET IN to the center point of an external resistor-divider network to set the threshold of the externally monitored voltage. See Reset Threshold section. Detailed Description The MAX6412-MAX6420 low-power microprocessor (P) supervisory circuits provide maximum adjustability for supply-voltage monitoring and reset functionality. In addition, the MAX6412-MAX6420 reset timeout period is adjustable using an external capacitor. The MAX6412/MAX6413/MAX6414 have factory-trimmed reset threshold voltages in approximately 100mV increments from 1.575V to 5.0V with a manual reset input. The MAX6415/MAX6416/MAX6417 contain a reset threshold that can be adjusted to any voltage above 1.26V using external resistors. The MAX6418/MAX6419/MAX6420 offer both a factory-trimmed reset threshold and an adjustable reset threshold input for dual-voltage monitoring. known state. The MAX6412-MAX6420 P supervisory circuits provide the reset logic to prevent code-execution errors during power-up, power-down, and brownout conditions (see Typical Operating Circuit). For the MAX6413, MAX6416, and MAX6419, RESET changes from low to high whenever VCC or RESET IN drops below the reset threshold voltages. Once RESET IN and VCC exceed their respective reset threshold voltage(s), RESET remains high for the reset timeout period, then goes low. On power-up, once VCC reaches 1V, RESET is guaranteed to be a logic high. For applications requiring valid reset logic when VCC is less than 1V, see the section Ensuring a Valid RESET/RESET Output Down to VCC = 0V. A reset signal is asserted when VCC and/or RESET IN falls below the preset values or when MR is asserted. The reset remains asserted for an externally programmed interval after VCC and/or RESET IN has risen above the reset threshold or MR is deasserted. The active-low RESET output of the remaining supervisors is the inverse of the MAX6413, MAX6416, and MAX6419 active-high RESET output and is guaranteed valid for VCC 1V. Reset Output The MAX6415-MAX6420 monitor the voltage on RESET IN with an external resistor voltage-divider (Figure 1). The reset output is typically connected to the reset input of a P. A P's reset input starts or restarts the P in a www.maximintegrated.com Reset Threshold Maxim Integrated 5 MAX6412-MAX6420 Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Use the following formula to calculate the externally monitored voltage (VMON_TH): VCC VMON_TH = VRST x (R1 + R2)/R2 where VMON_TH is the desired reset threshold voltage and VRST is the reset input threshold (1.26V). Resistors R1 and R2 can have very high values to minimize current consumption due to low leakage currents. Set R2 to some conveniently high value (1M, for example) and calculate R1 based on the desired monitored voltage, using the following formula: R1 RESET IN R2 R1 = R2 x (VMON_TH/VRST - 1) () GND Manual Reset Input (MAX6412/MAX6413/MAX6414) Many P-based products require manual reset capability, allowing the operator, a technician, or external logic circuitry to initiate a reset. A logic low on MR asserts reset. Reset remains asserted while MR is low and for the reset timeout period after MR returns high. The MR has an internal 20k pullup resistor so it can be left open if not used. Connect a normally open momentary switch from MR to ground to create a manual reset function (external debounce circuitry is not required for long reset timeout periods). A manual reset option can easily be implemented with the MAX6415-MAX6420 by connecting a normally open momentary switch in parallel with R2 (Figure 2). When the switch is closed, the voltage on RESET IN goes to zero, initiating a reset. Similar to the MAX6412/MAX6413/ MAX6414 manual reset, reset remains asserted while the switch is closed and for the reset timeout period after the switch is opened. VMON_TH MAX6415 MAX6420 SRT Figure 2. Adding an External Manual Reset Function to the MAX6415-MAX6420 Monitoring Voltages Other than VCC (MAX6415/MAX6416/MAX6417) The MAX6415/MAX6416/MAX6417 contain an adjustable reset threshold input. These devices can be used to monitor voltages other than VCC. Calculate VMON_TH as shown in the Reset Threshold section. (See Figure 3.) VMON_TH VCC R1 R1 RESET IN R2 VCC RESET IN VCC R2 MAX6415 MAX6416 GND MAX6417 SRT VMON_TH = 1.26 x (R1 + R2)/R2 Figure 1. Calculating the Monitored Threshold Voltage (VMON_TH) www.maximintegrated.com VCC MAX6415 MAX6416 GND MAX6417 SRT Figure 3. Monitoring External Voltages Maxim Integrated 6 MAX6412-MAX6420 Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay VMON_TH VCC MAX6420 ONLY VCC LASER-TRIMMED RESISTORS 1.26V RL RESET CIRCUITRY (RESET) RESET P R1 R2 RESET IN GND SRT MAX6418 MAX6419 MAX6420 CSRT Figure 4. MAX6418/MAX6419/MAX6420 Monitoring Two Voltages Dual-Voltage Monitoring (MAX6418/MAX6419/MAX6420) The MAX6418/MAX6419/MAX6420 contain both factorytrimmed threshold voltages and an adjustable reset threshold input, allowing the monitoring of two voltages, VCC and VMON_TH (see Figure 4). Reset is asserted when either of the voltages falls below its respective threshold voltage. Application Information Selecting a Reset Capacitor The reset timeout period is adjustable to accommodate a variety of P applications. Adjust the reset timeout period (tRP) by connecting a capacitor (CSRT) between SRT and ground. Calculate the reset timeout capacitor as follows: The reset delay time is set by a current/capacitor-controlled ramp compared to an internal 0.65V reference. An internal 240nA ramp current source charges the external capacitor. The charge to the capacitor is cleared when a reset condition is detected. Once the reset condition is removed, the voltage on the capacitor ramps according to the formula: dV/dt = I/C. The CSRT capacitor must ramp to 0.65V to deassert the reset. CSRT must be a low-leakage (<10nA) type capacitor, ceramic is recommended. Operating as a Voltage Detector The MAX6412-MAX6420 can be operated in a voltage detector mode by leaving SRT unconnected. The reset delay times for VCC rising above or falling below the threshold are not significantly different. The reset output is deasserted smoothly without false pulses. CSRT = (tRP - 275s) / (2.71 x 106) where tRP is in seconds and CSRT is in Farads www.maximintegrated.com Maxim Integrated 7 MAX6412-MAX6420 3.3V Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay 5.0V VCC 10k RESET MAX6414 MAX6417 MAX6420 5V SYSTEM GND CMOS-logic inputs connected to RESET can drift to undetermined voltages. This presents no problems in most applications, since most Ps and other circuitry do not operate with VCC below 1V. In those applications where RESET must be valid down to 0, adding a pulldown resistor between RESET and ground sinks any stray leakage currents, holding RESET low (Figure 6). The value of the pulldown resistor is not critical; 100k is large enough not to load RESET and small enough to pull RESET to ground. For applications using the MAX6413, MAX6416, and MAX6419, a 100k pullup resistor between RESET and VCC will hold RESET high when VCC falls below 1V (Figure 7). Open-drain RESET versions are not recommended for applications requiring valid logic for VCC down to 0V. Figure 5. MAX6414/MAX6417/MAX6420 Open-Drain RESET Output Allows use with Multiple Supplies Interfacing to Other Voltages for Logic Compatibility The open-drain outputs of the MAX6414/MAX6417/ MAX6420 can be used to interface to Ps with other logic levels. As shown in Figure 5, the open-drain output can be connected to voltages from 0 to 5.5V. This allows for easy logic compatibility to various microprocessors. Negative-Going VCC Transients In addition to issuing a reset to the P during power-up, power-down, and brownout conditions, these supervisors are relatively immune to short-duration negative-going transients (glitches). The Maximum Transient Duration vs. Reset Threshold Overdrive graph in the Typical Operating Characteristics shows this relationship. The area below the curve of the graph is the region in which these devices typically do not generate a reset pulse. This graph was generated using a negative-going pulse applied to VCC, starting above the actual reset threshold (VTH) and ending below it by the magnitude indicated (reset-threshold overdrive). As the magnitude of the transient decreases (farther below the reset threshold), the maximum allowable pulse width decreases. Typically, a VCC transient that goes 100mV below the reset threshold and lasts 50s or less will not cause a reset pulse to be issued. Ensuring a Valid RESET or RESET Down to VCC = 0V When VCC falls below 1V, RESET/RESET current sinking (sourcing) capabilities decline drastically. In the case of the MAX6412, MAX6415, and MAX6418, high-impedance www.maximintegrated.com VCC MAX6412 MAX6415 MAX6418 VCC RESET 100k GND Figure 6. Ensuring RESET Valid to VCC = 0V VCC MAX6413 MAX6416 MAX6419 VCC 100k RESET GND Figure 7. Ensuring RESET Valid to VCC = 0V Maxim Integrated 8 MAX6412-MAX6420 Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Layout Consideration SRT is a precise current source. When developing the layout for the application, be careful to minimize board capacitance and leakage currents around this pin. Traces connected to SRT should be kept as short as possible. Traces carrying high-speed digital signals and traces with large voltage potentials should be routed as far from SRT as possible. Leakage current and stray capacitance (e.g., a scope probe) at this pin could cause errors in the reset timeout period. When evaluating these parts, use clean prototype boards to ensure accurate reset periods. RESET IN is a high-impedance input, which is typically driven by a high-impedance resistor-divider network (e.g., 1M to 10M). Minimize coupling to transient signals by keeping the connections to this input short. Any DC leakage current at RESET IN (e.g., a scope probe) causes errors in the programmed reset threshold. Chip Information TRANSISTOR COUNT: 325 PROCESS: BiCMOS www.maximintegrated.com Table 1. Reset Voltages Suffix Table SUFFIX MIN TYP MAX 16 1.536 1.575 1.614 17 1.623 1.665 1.707 18 1.755 1.800 1.845 19 1.853 1.900 1.948 20 1.950 2.000 2.050 21 2.048 2.100 2.153 22 2.133 2.188 2.243 23 2.313 2.313 2.371 24 2.340 2.400 2.460 25 2.438 2.500 2.563 26 2.559 2.625 2.691 27 2.633 2.700 2.768 28 2.730 2.800 2.870 29 2.852 2.925 2.998 30 2.925 3.000 3.075 31 2.998 3.075 3.152 32 3.120 3.200 3.280 33 3.218 3.300 3.383 34 3.315 3.400 3.485 35 3.413 3.500 3.558 36 3.510 3.600 3.690 37 3.608 3.700 3.793 38 3.705 3.800 3.895 39 3.803 3.900 3.998 40 3.900 4.000 4.100 41 3.998 4.100 4.203 42 4.095 4.200 4.305 43 4.193 4.300 4.408 44 4.266 4.375 4.484 45 4.388 4.500 4.613 46 4.509 4.625 4.741 47 4.583 4.700 4.818 48 4.680 4.800 4.920 49 4.778 4.900 5.023 50 4.875 5.000 5.125 Maxim Integrated 9 MAX6412-MAX6420 Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Standard Versions Table PART* Ordering Information TEMP RANGE PIN-PACKAGE MAX6412UK16-T MAX6412UK_ _-T -40C to +125C 5 SOT23 MAX6412UK22-T MAX6412UK_ _+T -40C to +125C 5 SOT23 MAX6412UK26-T MAX6413UK_ _-T -40C to +125C 5 SOT23 MAX6412UK29-T MAX6413UK_ _+T -40C to +125C 5 SOT23 MAX6412UK46-T MAX6414UK_ _-T -40C to +125C 5 SOT23 MAX6413UK16-T MAX6414UK_ _+T -40C to +125C 5 SOT23 MAX6413UK22-T MAX6414UK_ _/V+T* -40C to +125C 5 SOT23 MAX6413UK26-T MAX6415UK+T -40C to +125C 5 SOT23 MAX6413UK29-T MAX6416UK+T -40C to +125C 5 SOT23 MAX6413UK46-T MAX6417UK+T -40C to +125C 5 SOT23 MAX6414UK16-T MAX6418UK_ _-T -40C to +125C 5 SOT23 MAX6414UK22-T MAX6418UK_ _+T -40C to +125C 5 SOT23 MAX6414UK26-T MAX6419UK_ _-T -40C to +125C 5 SOT23 MAX6414UK29-T MAX6419UK_ _+T -40C to +125C 5 SOT23 MAX6414UK46-T MAX6420UK_ _-T -40C to +125C 5 SOT23 MAX6415UK-T MAX6420UK_ _+T -40C to +125C 5 SOT23 MAX6416UK-T MAX6420UK_ _/V-T* -40C to +125C 5 SOT23 MAX6417UK-T MAX6418UK16-T MAX6418UK22-T MAX6418UK26-T MAX6418UK29-T MAX6418UK46-T MAX6419UK16-T MAX6419UK22-T MAX6419UK26-T MAX6419UK29-T MAX6419UK46-T MAX6420UK16-T PART Note: The MAX6412/MAX6413/MAX6414 and MAX6418/ MAX6419/MAX6420 are available with factory-set VCC reset thresholds from 1.575V to 5.0V in approximately 0.1V increments. Insert the desired nominal reset threshold suffix (from Table 1) into the blanks following the letters UK. There are 33 standard versions with a required order increment of 2500 pieces. Sample stock is generally held on standard versions only (see Standard Versions Table). Required order increment is 10,000 pieces for nonstandard versions. Contact factory for availability. All devices are available in tape-and-reel only. Devices are available in both leaded (-) and lead-free (+) packaging. /V denotes an automotive qualified part. For top mark information, please visit Maxim's website at www.maximintegrated.com. *Future product--contact factory for availability. MAX6420UK22-T MAX6420UK26-T MAX6420UK29-T MAX6420UK46-T *Sample Stock is generally held on all standard versions. Contact factory for availability of nonstandard versions. www.maximintegrated.com Maxim Integrated 10 MAX6412-MAX6420 Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Selector Guide PART FIXED VTH MANUAL RESET RESET IN PUSH-PULL RESET PUSH-PULL RESET OPEN-DRAIN RESET MAX6412 u u -- u -- -- MAX6413 u u -- -- u -- MAX6414 u u -- -- -- u MAX6415 -- -- u u -- -- MAX6416 -- -- u -- u -- MAX6417 -- -- u -- -- u MAX6418 u -- u u -- -- MAX6419 u -- u -- u -- MAX6420 u -- u -- -- u Typical Operating Circuit Package Information VCC VCC MR RESET/RESET MAX6412 MAX6413 MAX6414 GND www.maximintegrated.com RESET/RESET P For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 5 SOT23 U5+2, U5-2 21-0057 90-0174 SRT Maxim Integrated 11 MAX6412-MAX6420 Low-Power, Single/Dual-Voltage P Reset Circuits with Capacitor-Adjustable Reset Timeout Delay Revision History REVISION NUMBER REVISION DATE PAGES CHANGED 0 01/02 Initial release -- 1 8/03 Corrected top marks 10 2 12/05 Added lead-free information in Ordering Information 1 3 3/10 Deleted RESET in Hysteresis parameter in the Electrical Characteristics table 3 DESCRIPTION 4 2/11 Corrected formula for SRT 5 8/12 Added automotive qualified part to Ordering Information 1 6 3/14 Added MAX6414UK_ _/V+T to Ordering Information 1 12/15 Added lead-free part numbers to Ordering Information table, updated package code and removed top mark information from page 10. 7 5, 7 1, 10 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated's website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. (c) 2015 Maxim Integrated Products, Inc. 12 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX6412UK22+T MAX6413UK29+T MAX6414UK29+T MAX6415UK+T MAX6416UK+T MAX6417UK+T MAX6418UK29+T MAX6419UK31+T MAX6420UK29+T MAX6420UK32+T MAX6412UK16+T MAX6412UK17+T MAX6412UK18+T MAX6412UK19+T MAX6412UK20+T MAX6412UK21+T MAX6412UK23+T MAX6412UK24+T MAX6412UK25+T MAX6412UK26+T MAX6412UK27+T MAX6412UK28+T MAX6412UK29+T MAX6412UK30+T MAX6412UK31+T MAX6412UK32+T MAX6412UK33+T MAX6412UK34+T MAX6412UK35+T MAX6412UK36+T MAX6412UK37+T MAX6412UK38+T MAX6412UK39+T MAX6412UK40+T MAX6412UK41+T MAX6412UK42+T MAX6412UK43+T MAX6412UK44+T MAX6412UK45+T MAX6412UK46+T MAX6412UK47+T MAX6412UK48+T MAX6412UK49+T MAX6412UK50+T MAX6413UK16+T MAX6413UK17+T MAX6413UK18+T MAX6413UK19+T MAX6413UK20+T MAX6413UK21+T MAX6413UK22+T MAX6413UK23+T MAX6413UK24+T MAX6413UK25+T MAX6413UK26+T MAX6413UK27+T MAX6413UK28+T MAX6413UK30+T MAX6413UK31+T MAX6413UK32+T MAX6413UK33+T MAX6413UK34+T MAX6413UK35+T MAX6413UK36+T MAX6413UK37+T MAX6413UK38+T MAX6413UK39+T MAX6413UK40+T MAX6413UK41+T MAX6413UK42+T MAX6413UK43+T MAX6413UK44+T MAX6413UK45+T MAX6413UK46+T MAX6413UK47+T MAX6413UK48+T MAX6413UK49+T MAX6413UK50+T MAX6414UK16+T MAX6414UK17+T MAX6414UK175+T MAX6414UK18+T MAX6414UK19+T MAX6414UK20+T MAX6414UK21+T MAX6414UK22+T MAX6414UK23+T MAX6414UK24+T MAX6414UK25+T MAX6414UK26+T MAX6414UK27+T MAX6414UK28+T MAX6414UK30+T MAX6414UK31+T MAX6414UK32+T MAX6414UK33+T MAX6414UK34+T MAX6414UK35+T MAX6414UK36+T MAX6414UK37+T