111517
19
X7R Dielectric
General Specifications
X7R formulations are called “temperature stable” ceramics and fall into EIA
Class II materials. X7R is the most popular of these intermediate dielectric
constant materials. Its temperature variation of capacitance is within ±15%
from -55°C to +125°C. This capacitance change is non-linear.
Capacitance for X7R varies under the influence of electrical operating con-
ditions such as voltage and frequency.
X7R dielectric chip usage covers the broad spectrum of industrial
applications where known changes in capacitance due to applied voltages
are acceptable.
PART NUMBER (see page 2 for complete part number explanation)
0805
Size
(L" x W")
5
Voltage
4V = 4
6.3V = 6
10V = Z
16V = Y
25V = 3
50V = 5
100V = 1
200V = 2
500V = 7
C
Dielectric
X7R = C
103
Capacitance
Code (In pF)
2 Sig. Digits + Num-
ber of Zeros
M
Capacitance
Tolerance
J = ± 5%*
K = ±10%
M = ± 20%
*≤1µF only,
contact factory for addi-
tional values
2
Packaging
2 = 7" Reel
4 = 13" Reel
Contact
Factory For
Multiples
A
Special
Code
A = Std. Product
T
Terminations
T = Plated Ni
and Sn
Z= FLEXITERM®**
A
Failure
Rate
A = Not
Applicable
*Optional termination
**See FLEXITERM®
X7R section
NOTE: Contact factory for availability of Termination and Tolerance Options for Specific Part Numbers.
Contact factory for non-specified capacitance values.
20
111517
X7R Dielectric
Specifications and Test Methods
Parameter/Test X7R Specification Limits Measuring Conditions
Operating Temperature Range -55ºC to +125ºC Temperature Cycle Chamber
Capacitance Within specified tolerance
≤ 10% for ≥ 50V DC rating Freq.: 1.0 kHz ± 10%
Dissipation Factor ≤ 12.5% for 25V DC rating Voltage: 1.0Vrms ± .2V
≤ 12.5% for 25V and 16V DC rating For Cap > 10µF, 05Vrm @ 120Hz
≤ 12.5% for ≤ 10V DC rating
Insulation Resistance 100,000MΩ or 1000MΩ - µF, Charge device with rated voltage for
whichever is less 120 ± 5 secs @ room temp/humidity
Charge device with 250% of rated voltage for
Dielectric Strength No breakdown or visual defects 1-5 seconds, w/charge and discharge current
limited to 50 mA (max)
Note: Charge device with 150% of rated
voltage for 500V devices.
Appearance No defects Deflection: 2mm
Capacitance Test Time: 30 seconds
Resistance to Variation ≤ ±12%
Flexure Dissipation Meets Initial Values (As Above)
Stresses Factor
Insulation ≥ Initial Value x 0.3
Resistance
Solderability ≥ 95% of each terminal should be covered Dip device in eutectic solder at 230 ± 5ºC
with fresh solder for 5.0 ± 0.5 seconds
Appearance No defects, <25% leaching of either end terminal
Capacitance
Variation ≤ ±7.5%
Dip device in eutectic solder at 260ºC for 60
Dissipation Meets Initial Values (As Above) seconds. Store at room temperature for 24 ± 2
Resistance to Factor hours before measuring electrical properties.
Solder Heat Insulation Meets Initial Values (As Above)
Resistance
Dielectric Meets Initial Values (As Above)
Strength
Appearance No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes
Capacitance
Variation ≤ ±7.5% Step 2: Room Temp ≤ 3 minutes
Dissipation Meets Initial Values (As Above) Step 3: +125ºC ± 2º 30 ± 3 minutes
Thermal Factor
Shock Insulation Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutes
Resistance
Dielectric Meets Initial Values (As Above) Repeat for 5 cycles and measure after
Strength 24 ± 2 hours at room temperature
Appearance No visual defects
Capacitance
Variation ≤ ±12.5%
Dissipation ≤ Initial Value x 2.0 (See Above)
Load Life Factor
Insulation ≥ Initial Value x 0.3 (See Above)
Resistance
Dielectric Meets Initial Values (As Above)
Strength
Appearance No visual defects
Capacitance
Variation ≤ ±12.5%
Load Dissipation ≤ Initial Value x 2.0 (See Above)
Humidity Factor
Insulation ≥ Initial Value x 0.3 (See Above)
Resistance
Dielectric Meets Initial Values (As Above)
Strength
Charge device with 1.5 rated voltage (≤ 10V) in
test chamber set at 125ºC ± 2ºC
for 1000 hours (+48, -0)
Remove from test chamber and stabilize
at room temperature for 24 ± 2 hours
before measuring.
Store in a test chamber set at 85ºC ± 2ºC/
85% ± 5% relative humidity for 1000 hours
(+48, -0) with rated voltage applied.
Remove from chamber and stabilize at
room temperature and humidity for
24 ± 2 hours before measuring.
111517 21
X7R Dielectric
Capacitance Range
PREFERRED SIZES ARESHADED
SIZE 0101* 0201 0402 0603 0805 1206
Soldering Reflow Only Reflow Only Reflow/Wave Reflow/Wave Reflow/Wave Reflow/Wave
Packaging
Paper/Embossed
All Paper All Paper All Paper Paper/Embossed Paper/Embossed
(L) Length
mm
(in.) 0.40 ±0.02
(0.016 ±0.0008) 0.60 ±0.03
(0.024 ±0.001) 1.00 ±0.10
(0.040 ±0.004) 1.60 ±0.15
(0.063 ±0.006) 2.01 ±0.20
(0.079 ±0.008) 3.20 ±0.20
(0.126 ±0.008)
(W) Width
mm
(in.) 0.20 ±0.02
(0.008 ±0.0008) 0.30 ±0.03
(0.011 ±0.001) 0.50 ±0.10
(0.020 ±0.004) 0.81 ±0.15
(0.032 ±0.006) 1.25 ±0.20
(0.049 ±0.008) 1.60 ±0.20
(0.063 ±0.008)
(t) Terminal
mm
(in.) 0.10±0.04
(0.004 ±0.0016) 0.15 ±0.05
(0.006 ±0.002) 0.25 ±0.15
(0.010 ±0.006) 0.35 ±0.15
(0.014 ±0.006) 0.50 ±0.25
(0.020 ±0.010) 0.50 ±0.25
(0.020 ±0.010)
WVDC 16 6.3 10 16 25 50 6.3 10 16 25 50 6.3 10 16 25 50 100 200 6.3 10 16 25 50 100 200 6.3 10 16 25 50 100 200 500
Cap
100 101 B A A A A A C C C G G G
(pF)
150 151 B A A A A A C C C G G G
220 221 B A A A A A C C C G G G
330 331 B A A A A A C C C G G G J J J J J J K
470 471 B A A A A A C C C G G G J J J J J J K
680 681 B A A A A C C C G G G J J J J J J K
1000 102 B A A A A C C C C G G G J J J J J J K
1500 152 B A A A A C C C C G G J J J J J J J J J J J J M
2200 222 B A A A A C C C C G G J J J J J J J J J J J J M
3300 332 A A A A C C C C G G J J J J J J J J J J J J M
4700 472 A A A A C C C C G G J J J J J J J J J J J J M
6800 682 A A A A C C C C G G J J J J J J J J J J J J P
Cap
0.01 103 A A A A C C C C G G G J J J J J J J J J J J J J P
(µF)
0.015 153 C C C C G G G J J J J J J J J J J J J M Q
0.022 223 A C C C C G G G J J J J J N J J J J J M Q
0.033 333 C C C C G G J J J J J N N J J J J J M Q
0.047 473 A C C C C G G G J J J J J N N J J J J J M
0.068 683 C C C C G G G J J J J J N N J J J J J P
0.1 104 A C C C C G G G G J J J J J N N J J J J P P
0.15 154 G G G G J J J N N J J J J Q
0.22 224 C C C G G J J J J J N N N J J J J Q
0.33 334 J J J J N N N N N J J M P Q
0.47 474 C C J J J J J N N N N N M M M P Q
0.68 684 J J J N N N M M Q Q Q
1.0 105 C J J J J J N N N N M M Q Q Q
2.2 225 J J J P P P P** Q Q Q Q Q**
4.7 475 J P P P Q Q Q Q
10 106 P P P Q Q X X
22 226 Q Q Q
47 476 Q Q X
100 107
WVDC 16 6.3 10 16 25 50 6.3 10 16 25 50 6.3 10 16 25 50 100 200 6.3 10 16 25 50 100 200 6.3 10 16 25 50 100 200 500
SIZE 0101 0201 0402 0603 0805 1206
Letter A B C E G J K M N P Q X Y Z
Max.
Thickness 0.33
(0.013) 0.22
(0.009) 0.56
(0.022) 0.71
(0.028) 0.90
(0.035) 0.94
(0.037) 1.02
(0.040) 1.27
(0.050) 1.40
(0.055) 1.52
(0.060) 1.80
(0.071) 2.29
(0.090) 2.54
(0.100) 2.79
(0.110)
PAPER EMBOSSED
NOTE: Contact factory for non-sp ecified capacita ncevalues
*EIA01005
**Contact Factory forSpecifications
PAPERand EMBOSSED available for 01005
22
111517
X7R Dielectric
Capacitance Range
PREFERRED SIZES ARE SHADED
SIZE 1210 1812 1825 2220 2225
Soldering Reflow Only Reflow Only Reflow Only Reflow Only Reflow Only
Packaging Paper/Embossed All Embossed All Embossed All Embossed All Embossed
(L) Length mm 3.30 ± 0.4 4.50 ± 0.30 4.50 ± 0.30 5.70 ± 0.40 5.72 ± 0.25
(in.) (0.130± 0.016) (0.177 ± 0.012) (0.177 ± 0.012) (0.225 ± 0.016) (0.225 ± 0.010)
(W) Width mm 2.50 ± 0.20 3.20 ± 0.20 6.40 ± 0.40 5.00 ± 0.40 6.35 ± 0.25
(in.) (0.098 ± 0.008) (0.126 ± 0.008) (0.252 ± 0.016) (0.197 ± 0.016) (0.250 ± 0.010)
(t) Terminal mm 0.50 ± 0.25 0.61 ± 0.36 0.61 ± 0.36 0.64 ± 0.39 0.64 ± 0.39
(in.) (0.020 ± 0.010) (0.024 ± 0.014) (0.024 ± 0.014) (0.025 ± 0.015) (0.025 ± 0.015)
WVDC 10 16 25 50 100 200 500 16 25 50 100 200 500 50 100 200 25 50 100 200 500 50 100 200
Cap 100 101
(pF) 150 151
220 221
330 331
470 471
680 681
1000 102
1500 152 J J J J J J M
2200 222 J J J J J J M
3300 332 J J J J J J M
4700 472 J J J J J J M
6800 682 J J J J J J M
Cap 0.01 103 J J J J J J M K K K K K M M M X X X X M P P
(µF) 0.015 153 J J J J J J P K K K K P M M M X X X X M P P
0.022 223 J J J J J J Q K K K K P M M M X X X X M P P
0.033 333 J J J J J J Q K K K K X M M M X X X X M P P
0.047 473 J J J J J J Q K K K K Z M M M X X X X M P P
0.068 683 J J J J J M Q K K K K Z M M M X X X X M P P
0.1 104 J J J J J M X K K K K Z M M M X X X X M P P
0.15 154 J J J J M Z K K K P Z M M M X X X X M P X
0.22 224 J J J J P Z K K K P Z M M M X X X X M P X
0.33 334 J J J J Q K K M X M M X X X X M P X
0.47 474 M M M M Q K K P X M M X X X X M P X
0.68 684 M M P X X M M Q M P X X M P X
1.0 105 N N P X Z M M X Z M P X X M P X
1.5 155 N N Z Z Z Z Z Z Q X X M X Z
2.2 225 X X Z Z Z Z Z Z X X M X Z
3.3 335 X X Z Z Z Z Z Z X Z
4.7 475 Z Z Z Z Z Z X Z
10 106 Z Z Z Z Z ZZ
22 226 Z Z Z Z
47 476 Z
100 107
WVDC 10 16 25 50 100 200 500 16 25 50 100 200 500 50 100 200 25 50 100 200 500 50 100 200
SIZE 1210 1812 1825 2220 2225
Letter ABCEGJKMNPQXYZ
Max. 0.33 0.22 0.56 0.71 0.90 0.94 1.02 1.27 1.40 1.52 1.80 2.29 2.54 2.79
Thickness (0.013) (0.009) (0.022) (0.028) (0.035) (0.037) (0.040) (0.050) (0.055) (0.060) (0.071) (0.090) (0.100) (0.110)
PAPER EMBOSSED
NOTE: Contact factory for non-specified capacitance values
Z
Z
Z
Z
Z
Z
X
XXZ
Z
Z
Z
X
XZ
Z
Z
Z
Z