SiT8103 High Performance 1-110 MHz Oscillator Features, Benefits and Applications MEMS oscillator with LVCMOS/LVTTL compatible output 1-110 MHz frequency range Frequency stability as low as 20 PPM Typical current consumption of 6.1 mA in active mode Standby or output enable modes 1.8V, 2.5V - 3.3V supply voltage SoftEdgeTM configurable rise/fall time for driving higher loads or EMI reduction. Four industry-standard packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2, 7.0 x 5.0 mm All-silicon device with outstanding reliability of 2 FIT, 10x improvement over quartz-based devices Ultra short lead time Ideal for consumer electronics: video, set top boxes, HDTV, DVR, scanners, printers, IP camera, etc. Ideal for high-speed serial protocols: Ethernet, USB, SATA, SAS, Fibre Channel, Firewire, PCI Express Specifications Electrical Characteristics[1] Parameter Output Frequency Range Frequency Stability Aging Operating Temperature Range Symbol Min. Typ. Max. Unit Condition f F_stab 1 -20 -25 - - - 110 +20 +25 MHz PPM PPM Inclusive of: Initial stability, operating temperature, rated power, supply voltage change, load change, shock and vibration. -30 - +30 PPM -50 - +50 PPM Ag -1.0 - 1.0 PPM 1st year at 25C T_use - - 1.8 2.5 2.8 3.3 6.7 6.1 2.4 1.2 0.4 50 50 1 1.3 1.9 2.3 2.9 3.4 - +70 +85 1.89 2.75 3.08 3.63 7.5 6.7 4.3 2.2 0.8 55 60 2 2.5 2.6 3.3 3.9 4.6 - C C V V V V mA mA A A A % % ns ns ns ns ns ns Vdd Extended Commercial Industrial Any voltage between 2.5V and 3.3V is supported with 1 decimal point resolution. 20 PPM available in extended commercial temperature only Rise/Fall Time Tr, Tf Output Voltage High VOH -20 -40 1.71 2.25 2.52 2.97 - - - - - 45 40 - - - - - - 90% Output Voltage Low VOL - - 10% Vdd No load condition, f = 20 MHz, Vdd = 2.5 V, 2.8 V or 3.3 V No load condition, f = 20 MHz, Vdd = 1.8 V ST = GND, Vdd = 3.3 V, Output is Weakly Pulled Down ST = GND, Vdd = 2.5 or 2.8 V, Output is Weakly Pulled Down ST = GND, Vdd = 1.8 V, Output is Weakly Pulled Down All Vdds. f <= 75 MHz All Vdds. f > 75 MHz 15pF load, 20% - 80% Vdd=2.5V, 2.8V or 3.3V 15pF load, 20% - 80% Vdd=1.8V 30pF load, 20% - 80% Vdd=2.5V, 2.8V or 3.3V 30pF load, 20% - 80% Vdd=1.8V 45pF load, 20% - 80% Vdd=2.5V, 2.8V or 3.3V 45pF load, 20% - 80% Vdd=1.8V IOH = -4 mA (Vdd = 3.3 V) IOH = -3 mA (Vdd = 2.8 V and Vdd = 2.5 V) IOH = -2 mA (Vdd = 1.8 V) Input Voltage High Input Voltage Low Startup Time Resume Time RMS Period Jitter VIH VIL T_start T_resume T_jitt 70% - - - - - - - - - - 3.0 - - 0.6 0.8 - 30% 10 4 4.0 6.5 - - Vdd Vdd ms ms ps ps ps ps Pin 1, OE or ST Pin 1, OE or ST Measured from the time Vdd reaches its rated minimum value Measured from the time ST pin crosses 50% threshold f = 75 MHz, Vdd = 2.5 V, 2.8 V or 3.3 V f = 75 MHz, Vdd = 1.8 V f = 75 MHz @ BW: 900 kHz to 7.5 MHz, VDD = 2.5 V to 3.3 V f = 75 MHz @ BW: 900 kHz to 7.5 MHz, VDD = 1.8 V Supply Voltage Vdd Current Consumption Idd Standby Current Duty Cycle RMS Phase Jitter (random) I_std DC T_phj Note: 1. All electrical specifications in the above table are measured with 15pF output load, unless stated otherwise in the Condition. For more information about SoftEdgeTM rise/fall time for driving higher output load or reducing EMI, download http://www.sitime.com/support2/documents/AN10022-rise-and-fall-time-rev1.1.pdf. SiTime Corporation Rev. 1.46 990 Almanor Avenue Sunnyvale, CA 94085 (408) 328-4400 www.sitime.com Revised August 11, 2011 SiT8103 High Performance 1-110 MHz Oscillator Pin Description Tables Pin #1 Functionality OE H or Open[2]: Pin Map specified frequency output L: output is high impedance ST H or Open: specified frequency output Pin Connection 1 OE/ST 2 GND 3 CLK 4 VDD L: output is low level (weak pull down). Oscillation stops Absolute Maximum Table Attempted operation outside the absolute maximum ratings of the part may cause permanent damage to the part. Actual performance of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings. Min. Max. Unit Storage Temperature Parameter -65 150 C VDD -0.5 4 V Electrostatic Discharge - 6000 V Theta JA (with copper plane on VDD and GND) - 75 C/W C/W Theta JC (with PCB traces of 0.010 inch to all pins) - 24 Soldering Temperature (follow standard Pb free soldering guidelines) - 260 C Number of Program Writes - 1 NA 1,000+ - years Program Retention over -40 to 125C, Process, VDD (0 to 3.65 V) Environmental Compliance Parameter Condition/Test Method Mechanical Shock MIL-STD-883F, Method 2002 Mechanical Vibration MIL-STD-883F, Method 2007 Temperature Cycle JESD22, Method A104 Solderability MIL-STD-883F, Method 2003 Moisture Sensitivity Level MSL1 @ 260C Startup and Resume Timing Diagram 90% Vdd: 2.5/2.8/3.3 V parts 95% Vdd: 1.8 V parts Vdd Vdd Pin 4 Voltage ST Voltage 50% Vdd T_resume T_start CLK Output T_start: Time to start from power-off (ST/OE Mode) CLK Output T_resume: Time to resume from ST (ST Mode Only) Note: 2. In 1.8 V mode, a resistor of <100 k between OE pin and VDD is required. Dimensions and Land Patterns Rev. 1.46 Page 2 of 4 www.sitime.com SiT8103 High Performance 1-110 MHz Oscillator Package Size - Dimensions (Unit: mm)[] Recommended Land Pattern (Unit: mm)[5] 2.5 x 2.0 x 0.75 mm 2.5 0.10 #3 1.5 0.5 #2 #2 #1 1.0 #1 #4 1.1 YXXXX 1.9 1.00 #3 2.0 0.10 #4 0.75 0.05 0.75 1.1 3.2 x 2.5 x 0.75 mm 3.2 0.15 2.1 #3 1.9 0.7 #2 #1 0.9 0.75 0.05 #2 1.2 #1 #4 0.9 YXXXX 2.2 #3 2.5 0.15 #4 1.4 5.0 x 3.2 x 0.75 mm 5.0 0.15 #4 #2 #1 2.2 0.8 1.6 0.75 0.05 #2 #3 1.1 YXXXX #1 2.54 2.39 #3 3.2 0.15 #4 1.15 1.5 7.0 x 5.0 x 0.90 mm #3 5.08 #4 No Connect [5] #2 0.90 0.10 #2 2.0 1.1 2.6 5.08 1.7 2.1 5.0 0.15 YXXXX #1 #3 3.81 7.0 0.15 #4 #1 1.4 2.2 Notes: 3. Top marking: Y denotes manufacturing origin and XXXX denotes manufacturing lot number. The value of "Y" will depend on the assembly location of the device 4. A capacitor of value 0.1 F between Vdd and GND is recommended. 5. The 7050 package with part number designation "-8" has NO center pad. Rev. 1.46 Page 3 of 4 www.sitime.com SiT8103 High Performance 1-110 MHz Oscillator Part No. Guide - How to Order The Part No. Guide is for reference only. For real-time customization and exact part number, use the SiTime Part Number Generator. SiT8103AC -13-18E -105.12345T Packaging "SiT8103" "T": Tape & Reel, 3K reel "Y": Tape & Reel, 1K reel Blank for Bulk Revision Letter "A" is the revision Frequency 1.00000 to 110.00000 MHz Part Family Feature Pin "E" for Output Enable "S" for Standby Temperature Range "C" Commercial, -20 to 70C "I" Industrial, -40 to 85C [8] Supply Voltage [6] Output Driver Strength "18" for 1.8 V 5% "25" for 2.5 V 10% "28" for 2.8 V 10% "33" for 3.3 V 10% "-" Default Package Size "1" 2.5 x 2.0 mm "2" 3.2 x 2.5 mm Frequency Stability "1" for 20 PPM "2" for 25 PPM "3" for 50 PPM "8" for 30 PPM "3" 5.0 x 3.2 mm "4" 7.0 x 5.0 mm "8" 7.0 x 5.0 mm[7] Notes: 6. Contact SiTime for different drive strength options for driving loads with faster rise/fall time spec than those shown in the electrical table, or reducing EMI. 7. Without Center Pad. 8. Supply voltage can be configured to any voltage up to 1 decimal place between 2.5V and 3.3V. Frequency Stability vs. Temperature Range Options Frequency Stability (PPM) Supply Voltage Temperature Range 1.8 V 2.5 V 2.8 V 3.3 V C (-20 to +70C) 3 3 3 3 I (-40 to +85C) - - - - 25 C (-20 to +70C) I (-40 to +85C) 3 3 3 3 30 C (-20 to +70C) I (-40 to +85C) 3 3 3 3 50 C (-20 to +70C) I (-40 to +85C) 3 3 3 3 20 (c) SiTime Corporation 2011. The information contained herein is subject to change at any time without notice. SiTime assumes no responsibility or liability for any loss, damage or defect of a Product which is caused in whole or in part by (i) use of any circuitry other than circuitry embodied in a SiTime product, (ii) misuse or abuse including static discharge, neglect or accident, (iii) unauthorized modification or repairs which have been soldered or altered during assembly and are not capable of being tested by SiTime under its normal test conditions, or (iv) improper installation, storage, handling, warehousing or transportation, or (v) being subjected to unusual physical, thermal, or electrical stress. Disclaimer: SiTime makes no warranty of any kind, express or implied, with regard to this material, and specifically disclaims any and all express or implied warranties, either in fact or by operation of law, statutory or otherwise, including the implied warranties of merchantability and fitness for use or a particular purpose, and any implied warranty arising from course of dealing or usage of trade, as well as any common-law duties relating to accuracy or lack of negligence, with respect to this material, any sitime product and any product documentation. products sold by sitme are not suitable or intended to be used in a life support application or component, to operate nuclear facilities, or in other mission critical applications where human life may be involved or at stake. all sales are made conditioned upon compliance with the critical uses policy set forth below. CRITICAL USE EXCLUSION POLICY BUYER AGREES NOT TO USE SITIME'S PRODUCTS FOR ANY APPLICATION OR IN ANY COMPONENTS USED IN LIFE SUPPORT DEVICES OR TO OPERATE NUCLEAR FACILITIES OR FOR USE IN OTHER MISSION-CRITICAL APPLICATIONS OR COMPONENTS WHERE HUMAN LIFE OR PROPERTY MAY BE AT STAKE. SiTime owns all rights, title and interest to the intellectual property related to SiTime's products, including any software, firmware, copyright, patent, or trademark. The sale of SiTime products does not convey or imply any license under patent or other rights. SiTime retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by SiTime. Unless otherwise agreed to in writing by SiTime, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited. Rev. 1.46 Page 4 of 4 Revised August 11, 2011