MC74VHCT139A Dual 2-to-4 Decoder/ Demultiplexer The MC74VHCT139A is an advanced high speed CMOS 2-to-4 decoder/demultiplexer fabricated with silicon gate CMOS technology. It achieves high speed operation similar to equivalent Bipolar Schottky TTL devices while maintaining CMOS low power dissipation. When the device is enabled (E = low), it can be used for gating or as a data input for demultiplexing operations. When the enable input is held high, all four outputs are fixed high, independent of other inputs. The internal circuit is composed of three stages, including a buffer output which provides high noise immunity and stable output. The device output is compatible with TTL-type input thresholds and the output has a full 5.0 V CMOS level output swing. The input protection circuitry on this device allows overvoltage tolerance on the input, allowing the device to be used as a logic-level translator from 3.0 V CMOS logic to 5.0 V CMOS logic, or from 1.8 V CMOS logic to 3.0 V CMOS logic while operating at the high-voltage power supply The MC74VHCT139A input structure provides protection when voltages up to 7.0 V are applied, regardless of the supply voltage. This allows the MC74VHCT139A to be used to interface 5.0 V circuits to 3.0 V circuits. The output structures also provide protection when VCC = 0 V. These input and output structures help prevent device destruction caused by supply voltage-input/output voltage mismatch, battery backup, hot insertion, etc. * * MARKING DIAGRAMS 16 SOIC-16 D SUFFIX CASE 751B 1 High Speed: tPD = 5.0 ns (Typ) at VCC = 5.0 V Low Power Dissipation: ICC = 4 m (Max) at TA = 25C TTL-Compatible Inputs: VIL = 0.8 V; VIH = 2.0 V Power Down Protection Provided on Inputs and Outputs Balanced Propagation Delays Designed for 2.0 V to 5.5 V Operating Range Low Noise: VOLP = 0.8 V (Max) Pin and Function Compatible with Other Standard Logic Families Latchup Performance Exceeds 300 mA ESD Performance: Human Body Model > 2000 V; Machine Model > 200 V Chip Complexity: 100 FETs or 25 Equivalent Gates Pb-Free Packages are Available* VHCT139AG AWLYWW 1 16 VHCT 139A ALYWG G TSSOP-16 DT SUFFIX CASE 948F 1 1 16 SOEIAJ-16 M SUFFIX CASE 966 1 Features * * * * * * * * * * http://onsemi.com 74VHCT139 ALYWG 1 A = Assembly Location WL, L = Wafer Lot Y = Year WW, W = Work Week G or G = Pb-Free Package (Note: Microdot may be in either location) FUNCTION TABLE Inputs Outputs E A1 A0 Y0 Y1 Y2 Y3 H L L L L X L L H H X L H L H H L H H H H H L H H H H H H L H H H L H ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. (c) Semiconductor Components Industries, LLC, 2006 January, 2006 - Rev. 4 1 Publication Order Number: MC74VHCT139A/D MC74VHCT139A ADDRESS INPUTS Ea 1 16 VCC A0a 2 15 Eb A1a 3 14 A0b Y0a 4 13 A1b Y1a 5 12 Y0b Y2a 6 11 Y1b Y3a 7 10 Y2b GND 8 9 Y3b A0a A1a 2 4 3 5 6 7 Y1a Y2a ACTIVE-LOW OUTPUTS Y3a 1 Ea ADDRESS INPUTS Y0a A0b A1b 14 12 13 11 10 9 Figure 1. Pin Assignment Eb Y0b Y1b Y2b ACTIVE-LOW OUTPUTS Y3b 15 Figure 2. Logic Diagram En Y0 Y1 A0 Y2 Y3 A1 Figure 3. Expanded Logic Diagram (1/2 of Device) A1a 3 A0a 2 Ea 1 1 X/Y 0 2 1 EN 2 3 INPUT 4 Y0a 5 Y1a A1a 3 A0a 2 6 Y2a 7 Y3a Ea 1 0 1 DMUX 0 0 G 3 1 2 3 12 Y0b 4 Y0a 5 Y1a 6 Y2a 7 Y3a 12 Y0b A1b 13 A0b 14 11 Y1b 10 Y2b A1b 13 A0b 14 11 Y1b 10 Y2b Eb 15 9 Y3b Eb 15 9 Y3b Figure 5. IEC Logic Diagram Figure 4. Input Equivalent Circuit http://onsemi.com 2 MC74VHCT139A MAXIMUM RATINGS (Note 1) Value Unit VCC Positive DC Supply Voltage Parameter -0.5 to +7.0 V VIN Digital Input Voltage -0.5 to +7.0 V VOUT DC Output Voltage -0.5 to +7.0 -0.5 to VCC +0.5 V IIK Input Diode Current -20 mA IOK Output Diode Current $20 mA IOUT DC Output Current, per Pin $25 mA ICC DC Supply Current, VCC and GND Pins PD Power Dissipation in Still Air TSTG Storage Temperature Range VESD ESD Withstand Voltage Symbol ILATCHUP qJA Latchup Performance Output in 3-State High or Low State SOIC Package TSSOP $75 mA 200 180 mW -65 to +150 C Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) >2000 >200 >2000 V Above VCC and Below GND at 125C (Note 5) $300 mA 143 164 C/W Thermal Resistance, Junction-to-Ambient SOIC Package TSSOP Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. 2. Tested to EIA/JESD22-A114-A 3. Tested to EIA/JESD22-A115-A 4. Tested to JESD22-C101-A 5. Tested to EIA/JESD78 RECOMMENDED OPERATING CONDITIONS Symbol Characteristics Min Max Unit 4.5 5.5 V VCC DC Supply Voltage VIN DC Input Voltage 0 5.5 V DC Output Voltage Output in 3-State High or Low State 0 0 5.5 VCC V -55 125 C 0 20 ns/V VOUT TA Operating Temperature Range, all Package Types tr, tf Input Rise or Fall Time VCC = 5.0 V + 0.5 V 47.9 100 178,700 20.4 110 79,600 9.4 120 37,000 4.2 130 17,800 2.0 140 8,900 1.0 TJ = 80 C 117.8 419,300 TJ = 90 C 1,032,200 90 TJ = 100 C 80 FAILURE RATE OF PLASTIC = CERAMIC UNTIL INTERMETALLICS OCCUR TJ = 110 C Time, Years TJ = 120 C Time, Hours TJ = 130 C Junction Temperature C NORMALIZED FAILURE RATE DEVICE JUNCTION TEMPERATURE VERSUS TIME TO 0.1% BOND FAILURES 1 1 10 100 1000 TIME, YEARS Figure 6. Failure Rate vs. Time Junction Temperature http://onsemi.com 3 MC74VHCT139A DC CHARACTERISTICS (Voltages Referenced to GND) VCC Symbol Parameter (V) Min VIH Minimum High-Level Input Voltage 4.5 to 5.5 2 VIL Maximum Low-Level Input Voltage 4.5 to 5.5 VOH Maximum High-Level Output Voltage VOL Maximum Low-Level Output Voltage Condition TA 85C TA = 25C Typ Max Min Max 2 0.8 VIN = VIH or VIL IOH = -50 mA 4.5 4.4 VIN = VIH or VIL IOH = -8 mA 4.5 3.94 VIN = VIH or VIL IOL = 50 mA 4.5 VIN = VIH or VIL IOH = 8 mA TA = - 55 to 125C Min Max 2 0.8 Unit V 0.8 V V 4.5 4.4 4.4 3.8 3.66 V 0 0.1 0.1 0.1 4.5 0.36 0.44 0.52 IIN Input Leakage Current VIN = 5.5 V or GND 0 to 5.5 0.1 1.0 1.0 mA ICC Maximum Quiescent Supply Current VIN = VCC or GND 5.5 4.0 40.0 40.0 mA ICCT Additional Quiescent Supply Current (per Pin) Any one input: VIN = 3.4 V All other inputs: VIN = VCC or GND 5.5 1.35 1.5 1.5 mA mA IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIII IIIIIIIII IIIIIII IIIII IIII II IIII IIIIIII IIIIIIIII IIIIIII IIIII IIII II IIIIIIIIIII IIIIIIIII IIIIIII IIIII III III III III III IIII III II II IIII IIIIIII IIIIIIIII III III III III III III II II IIIIIIIII III III III III III III II IIII IIIIIII II IIIIIIIIIII IIIIIIIII III III III III III III IIII IIIIIII III III III II II IIII IIIIIIIII III III III IIII IIIIIII IIIIIIIII III III III III III III II II II IIIIIIIIIII IIIIIIIII III III III III III III II IIIIIII IIIIIIIII III III III III III III II II IIII IIIIIIIIIII IIIIIIIII III III III III III III IIII IIII IIIIIIIIIII IIIIIIIII IIIIII III III IIIIII IOPD Output Leakage Current VOUT = 5.5 V 0 0.5 5 5 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0ns) TA 85C TA = 25C Symbol tPLH, tPHL tPLH, tPHL CIN Parameter Maximum Propagation Delay, A to Y Maximum Propagation Delay, E to Y Test Conditions Min TA = - 55 to 125C Typ Max Min Max Min Max Unit ns VCC = 3.3 0.3 V CL = 15 pF CL = 50 pF 7.2 9.7 11.0 14.5 1.0 1.0 13.0 16.5 1.0 1.0 13.0 16.5 VCC = 5.0 0.5 V CL = 15 pF CL = 50 pF 5.0 6.5 7.2 9.2 1.0 1.0 8.5 10.5 1.0 1.0 8.5 10.5 VCC = 3.3 0.3 V CL = 15 pF CL = 50 pF 6.4 8.9 9.2 12.7 1.0 1.0 11.0 14.5 1.0 1.0 11.0 14.5 VCC = 5.0 0.5 V CL = 15 pF CL = 50 pF 4.4 5.9 6.3 8.3 1.0 1.0 7.5 9.5 1.0 1.0 7.5 9.5 4 10 Maximum Input Capacitance 10 10 ns pF Typical @ 25C, VCC = 5.0V CPD 26 Power Dissipation Capacitance (Note 6) pF 6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC/2 (per decoder). CPD is used to determine the no-load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. http://onsemi.com 4 MC74VHCT139A A 3.0 V 1.5 V E GND 1.5 V tPHL tPLH Y 3.0 V tPLH tPHL VOH 1.5 V Figure 7. Switching Waveform VOH 1.5 V Y VOL GND VOL Figure 8. Switching Waveform TEST POINT OUTPUT DEVICE UNDER TEST C L* *Includes all probe and jig capacitance Figure 9. Test Circuit ORDERING INFORMATION Package Shipping MC74VHCT139AD SOIC-16 48 Units / Rail MC74VHCT139ADG SOIC-16 (Pb-Free) 48 Units / Rail MC74VHCT139ADR2 SOIC-16 2500 Tape & Reel MC74VHCT139ADR2G SOIC-16 (Pb-Free) 2500 Tape & Reel MC74VHCT139ADT TSSOP-16* 96 Units / Rail MC74VHCT139ADTG TSSOP-16* 96 Units / Rail MC74VHCT139ADTR2 TSSOP-16* 2500 Tape & Reel MC74VHCT139ADTRG TSSOP-16* 2500 Tape & Reel MC74VHCT139AM SOEIAJ-16 50 Units / Rail MC74VHCT139AMG SOEIAJ-16 (Pb-Free) 50 Units / Rail MC74VHCT139AMEL SOEIAJ-16 2000 Tape & Reel MC74VHCT139AMELG SOEIAJ-16 (Pb-Free) 2000 Tape & Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *This package is inherently Pb-Free. http://onsemi.com 5 MC74VHCT139A PACKAGE DIMENSIONS SOIC-16 D SUFFIX CASE 751B-05 ISSUE J NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. -A- 16 9 -B- 1 P 8 PL 0.25 (0.010) 8 B M S G R K DIM A B C D F G J K M P R F X 45 _ C -T- SEATING PLANE J M D 16 PL 0.25 (0.010) M T B S A MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 S TSSOP-16 DT SUFFIX CASE 948F-01 ISSUE A 16X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S K EEE CCC CCC EEE CCC K1 2X L/2 16 9 J1 B -U- L SECTION N-N J PIN 1 IDENT. 8 1 N 0.15 (0.006) T U S 0.25 (0.010) A -V- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. M N F DETAIL E -W- C 0.10 (0.004) -T- SEATING PLANE H D DETAIL E G http://onsemi.com 6 DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ MC74VHCT139A PACKAGE DIMENSIONS SOEIAJ-16 M SUFFIX CASE 966-01 ISSUE A 16X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S K EEE CCC CCC EEE K1 2X L/2 16 9 J1 B -U- L SECTION N-N J PIN 1 IDENT. 8 1 N 0.15 (0.006) T U S 0.25 (0.010) A -V- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. M N F DETAIL E -W- C 0.10 (0.004) -T- SEATING PLANE H D DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ DETAIL E G ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Phone: 81-3-5773-3850 Email: orderlit@onsemi.com http://onsemi.com 7 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. MC74VHCT139A/D