REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) Convert to military drawing format. Add vendor CAGE 01295. Changes to table I. Delete subgroup 9 from final electrical test parameters. Add case outline X. Added four devices 09 - 12. C Update part numbers for vendor CAGE number 01295. Correction on page 18, terminal connections. Editorial changes throughout. Add vendor CAGE numger 01295 as a supplier of the K package for device types 01 through 08. Changes to pages 5 and 6 table I. Changes to pages 10 and 11 terminal connections. Changes on pages 21 - 28. D APPROVED 87-07-06 M. A. Frye 88-05-06 M. A. Frye E Correct figure 1 device types 02 and 04 for case outline X. Boilerplate updated. ksr 04-08-06 Raymond Monnin F Update drawing to current requirements. Editorial changes throughout. ksr. 09-11-30 Charles F. Saffle G Update drawing to reflect current MIL-PRF-38535 requirements. - llb 17-09-27 Charles F. Saffle REV SHEET REV G G G G G G G G G G G G G G G G SHEET 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 REV STATUS REV G G G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.landandmaritime.dla.mil Greg Pitz STANDARD MICROCIRCUIT DRAWING CHECKED BY Charles Reusing APPROVED BY Michael Frye THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A DRAWING APPROVAL DATE 84-08-24 REVISION LEVEL MICROCIRCUIT, MEMORY, DIGITAL, BIPOLAR, PROGRAMMABLE LOGIC, MONOLITHIC SILICON SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 DISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited. 84129 1 OF 30 5962-E602-17 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 84129 01 J A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device types. The device types identify the circuit function as follows: Device type Generic number 1/ 01, 09 02, 10 03, 11 04, 12 05 06 07 08 Circuit PAL20L8A, L8A-2 PAL20R8A, R8A-2 PAL20R6A, R6A-2 PAL20R4A, R4A-2 PAL20L10A PAL20X8A PAL20X10A PAL20X4A 20-input 8-output AND-OR invert gate array 20-input 8-output registered AND-OR gate array 20-input 6-output registered AND-OR gate array 20-input 4-output registered AND-OR gate array 20-input 10-output AND-OR invert gate array 20-input 8-output registered AND-OR-XOR gate array 20-input 10-output registered AND-OR-XOR gate array 20-input 4-output registered AND-OR-XOR gate array 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator J K L X 3 GDIP1-T24 or CDIP2-T24 GDFP2-F24 or CDFP3-24 GDIP3-T24 or CDIP4-T24 CQCC1-N28 CQCC1-N28 Terminals Package style 24 24 24 28 28 dual-in-line package flat package dual-in-line package square chip carrier package 1/ square chip carrier package 1/ 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage range (VCC) ------------------------------------------------Input voltage range ------- --------------------------------------------------Storage temperature range -----------------------------------------------Lead temperature (soldering, 10 seconds) ----------------------------Thermal resistance, junction-to-case (JC): 2/ 3/ Cases J, K, L, X, and 3 -------------------------------------------------Output voltage applied -- --------------------------------------------------Output sink current ------- --------------------------------------------------Maximum power dissipation(PD) 3/ --------------------------------------Maximum junction temperature (TJ) -------------------------------------- -0.5 V dc to +12.0 V dc -1.5 V dc to +5.5 V dc -65C to +150C +260C (See MIL-STD-1835) -1.5 V dc to +12 V dc 100 mA 1.2 W +175C 1/ See figure 1. 2/ Heat sinking is recommended to reduce the junction temperature. 3/ Must withstand the added PD due to short circuit test (e.g., IOS). STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 2 1.4 Recommended operating conditions. Supply voltage (VCC) --------------------------------------------------------Minimum high level input voltage (VIH) ---------------------------------Maximum low level input voltage (VIL) ----------------------------------Case operating temperature range (TC)--------------------------------- 4.5 V dc minimum to 5.5 V dc maximum 2.0 V dc 0.8 V dc -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used. This drawing has been modified to allow the manufacturer to use the alternate die/fabrication requirements of paragraph A.3.2.2 of MIL-PRF-38535 or other alternative approved by the qualifying activity. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.2 Truth tables. The truth tables shall be as specified on figure 2. 3.2.2.1 Unprogrammed devices. The truth tables for unprogrammed devices for contracts involving no altered item drawing shall be as specified on figure 2. When required in groups A, B, or C (see 4.4), the devices shall be programmed by the manufacturer prior to test with a minimum of 50 percent of the total number of gates programmed or to any altered item drawing pattern which includes at least 25 percent of the total number of gates programmed. 3.2.2.2 Programmed devices. The truth tables for programmed devices shall be as specified by an attached altered item drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 3 3.2.3 Logic diagrams. The logic diagrams shall be as specified on figure 3. 3.2.4 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full (case or ambient) operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. 3.5.1 Certification/compliance mark. A compliance indicator "C" shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator "C" shall be replaced with a "Q" or "QML" certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. For product built in accordance with A.3.2.2 of MIL-PRF-38535, or as modified in the manufacturer's QM plan, the "QD" certification mark shall be used in place of the "Q" or "QML" certification mark. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Processing options. Since the device is capable of being programmed by either the manufacturer or the user to result in a wide variety of configurations, two processing options are provided for selection in the contract, using an altered item drawing. 3.10.1 Unprogrammed device delivered to the user. All testing shall be verified through group A testing as defined in 3.2.2.1 and table II. It is recommended that users perform subgroups 7 and 9 after programming to verify the specific program configuration. 3.10.2 Manufacturer-programmed device delivered to the user. All testing requirements and quality assurance provisions herein, including the requirements of the altered item drawing, shall be satisfied by the manufacturer prior to delivery. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 4 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C Group A subgroups Device type unless otherwise specified Limits Min Unit Max Input clamp voltage VIC VCC = 4.5 V, II = -18 mA 1 All High level output voltage VOH VCC = 4.5 V, VIL < 0.8 V, VIH > 2.0 V, IOH = -2 mA 1, 2, 3 All Low level output voltage VOL VCC = 4.5 V, VIL < 0.8 V, VIH > 2.0 V, IOH = 12 mA 1, 2, 3 All High level input voltage VIH VCC = 5.5 V 2/ 1, 2, 3 All Low level input voltage VIL VCC = 5.5 V 2/ 1, 2, 3 All 0.8 V High level input current IIH VCC = 5.5 V, VI = 2.4 V 3/ 1, 2, 3 All 40 A OE -1.5 V 2.4 V 0.5 V 2.0 others V 25 Low level input current IIL VCC = 5.5.V, VI = 0.4 V 3/ 1, 2, 3 All Output short circuit current IOS VCC = 5.5.V, VO = 0.4 V 3/ 1, 2, 3 01-08 -30 -0.25 mA -250 mA 09,10, 11,12 -130 Input current II VCC = 5.5 V, VI = 5.5. V 1, 2, 3 All 1.0 mA Off-state output current IOZL VCC = 5.5 V, VIL = 0.8 V, VIH = 2.4 V, VO = 0.4 V 3/ 1, 2, 3 All -250 A Off-state output current IOZH VCC = 5.5 V, VIL = 0.8 V, VIH = 2.4 V, VO = 2.4 V 3/ 1, 2, 3 All 100 A Supply current ICC VCC = 5.5 V 1, 2, 3 01,02, 03,04 210 mA 05 165 06,07, 08 180 09,10, 11,12 105 Functional testing See 4.3.1c 7, 8A, 8B All See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 5 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C Group A subgroups Device type unless otherwise specified Propagation delay data input to output Propagation delay data input to output Propagation delay high impedance to output high Propagation delay high impedance to output low Propagation delay output high to high impedance 5/ tPHL VCC = 5.0 V, CL = 50 pF +10%, R1 = 390, +5%, R2 = 750 +5% (or equivalent load circuit) Unless otherwise specified tPLH Min 9, 10, 11 9, 10, 11 tPZH 9, 10, 11 tPZL 9, 10, 11 tPHZ Limits 9, 10, 11 Unit Max 01,03, 04 30 05,06, 08 35 09,11, 12 50 01,03, 04 30 05,06, 08 35 09,11, 12 50 01,03, 04 30 05,06, 08 35 09,11, 12 45 01,03, 04 30 05,06, 08 35 09,11, 12 45 01,03, 04 30 05,06, 08 35 09,11, 12 45 ns ns ns ns ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C Group A subgroups Device type unless otherwise specified Propagation delay output low to high impedance 5/ tPLZ VCC = 5.0 V, CL = 50 pF +10%, R1 = 390, +5%, R2 = 750 +5% (or equivalent load circuit) Unless otherwise specified Limits Min 9, 10, 11 Unit Max 01,03, 04 30 05,06, 08 35 09,11, 12 45 ns Propagation delay high impedance to output high OE to all output pins tPZH 9, 10, 11 02,03, 04,06, 07,08, 10,11, 12 25 ns Propagation delay high impedance to output low OE to all output pins tPZL 9, 10, 11 02,03, 04,06, 07,08, 10,11, 12 25 ns Propagation delay output high to high impedance OE to all output pins 5/ tPHZ 9, 10, 11 02,03, 04,06, 07,08, 10,11, 12 25 ns Propagation delay output low to high impedance OE to all output pins 5/ tPLZ 9, 10, 11 02,03, 04,06, 07,08, 10,11, 12 25 ns Clock to output tPCH 9, 10, 11 02,03, 04 20 ns 06,07, 08,09, 10,11, 12 25 tPCL Minimum clock pulse width Minimum setup time 2/ tp(CL) 9, 10, 11 tsu 9, 10, 11 02,03, 04 20 06,07, 08 35 09,10, 11,12 25 02,03, 04 30 06,07, 08 40 09,10, 11,12 50 ns ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 7 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C Group A subgroups Device type unless otherwise specified Minimum hold time 2/ tH Maximum clock frequency 2/ fMAX 1/ 2/ 3/ 4/ 5/ VCC = 5.0 V, CL = 50 pF +10%, R1 = 390, +5%, R2 = 750 +5% (or equivalent load circuit) Unless otherwise specified Limits Min Unit Max 9, 10, 11 03,03, 04,06, 07,08, 09,10, 11,12 0 ns 9, 10, 11 02,03, 04 20 MHz 06,07, 08,09, 10,11, 12 15.3 Unless otherwise specified VCC is 4.5 V to 5.5 V. Tested only initially and after any design change, or used as setup condition, therefore guaranteed if not tested. I/O terminal leakage is the worst case of IIX or IOZX. Only one output shorted at a time. CL = 5 pF. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 8 FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 9 FIGURE 1. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 10 FIGURE 1. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 11 FIGURE 1. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 12 FIGURE 1. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 13 FIGURE 1. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 14 FIGURE 1. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 15 FIGURE 1. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 16 FIGURE 1. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 17 FIGURE 1. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 18 Device types 01 and 09 INPUTS OUTPUTS I13 I12 I11 I10 I9 I8 I7 I6 I5 I4 I3 I2 I1 I0 O7 X X X X X X X X X X X X X X Z I/O6 I/O5 I/O4 I/O3 I/O2 I/O1 Z Z Z Z O0 Z Z Z Device types 02 and 10 INPUTS OUTPUTS OE I11 I10 I9 I8 I7 I6 I5 I4 I3 I2 I1 I0 CLK O7 O6 O5 O4 O3 O2 O1 O0 H X X X X X X X X X X X X CLK Z Z Z Z Z Z Z Z L X X X X X X X X X X X X CLK H H H H H H H H Device types 03 and 11 INPUTS OUTPUTS OE I11 I10 I9 I8 I7 I6 I5 I4 I3 I2 I1 I0 CLK I/O7 O6 O5 O4 O3 O2 O1 I/O0 H X X X X X X X X X X X X CLK Z Z Z Z Z Z Z Z L X X X X X X X X X X X X CLK Z H H H H H H Z Device types 04 and 12 INPUTS OUTPUTS OE I11 I10 I9 I8 I7 I6 I5 I4 I3 I2 I1 I0 CLK I/O7 I/O6 O5 O4 O3 O2 H X X X X X X X X X X X X CLK Z Z Z Z Z Z Z Z L X X X X X X X X X X X X CLK Z Z H H H H Z Z I/O1 I/O0 FIGURE 2. Truth tables (unprogrammed). STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 19 Device types 05 INPUTS OUTPUTS I11 I10 I9 I8 I7 I6 I5 I4 I3 I2 I1 I0 O9 X X X X X X X X X X X X Z I/O8 I/O7 I/O6 I/O5 I/O4 I/O3 I/O2 I/O1 Z Z Z Z Z O0 Z Z Z Z Device types 06 INPUTS OUTPUTS OE I9 I8 I7 I6 I5 I4 I3 I2 I1 I0 CLK I/O9 O8 O7 O6 O5 O4 O3 O2 O1 I/O0 H X X X X X X X X X X CLK Z Z Z Z Z Z Z Z Z Z L X X X X X X X X X X CLK Z H H H H H H H H Z Device types 07 INPUTS OUTPUTS OE I9 I8 I7 I6 I5 I4 I3 I2 I1 I0 CLK O9 O8 O7 O6 O5 O4 O3 O2 O1 O0 H X X X X X X X X X X CLK Z Z Z Z Z Z Z Z Z Z L X X X X X X X X X X CLK H H H H H H H H H H Device types 08 INPUTS OUTPUTS OE I9 I8 I7 I6 I5 I4 I3 I2 I1 I0 CLK I/O9 I/O8 I/O7 O6 O5 O4 O3 H X X X X X X X X X X CLK Z Z Z Z Z Z Z Z Z Z L X X X X X X X X X X CLK Z Z Z H H H H Z Z Z I/O2 I/O1 I/O0 FIGURE 2. Truth tables (unprogrammed) - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 20 FIGURE 3. (Unprogrammed) Logic diagrams. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 21 FIGURE 3. (Unprogrammed) Logic diagrams - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 22 FIGURE 3. (Unprogrammed) Logic diagrams - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 23 FIGURE 3. (Unprogrammed) Logic diagrams - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 24 FIGURE 3. (Unprogrammed) Logic diagrams - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 25 FIGURE 3. (Unprogrammed) Logic diagrams - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 26 FIGURE 3. (Unprogrammed) Logic diagrams - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 27 FIGURE 3. (Unprogrammed) Logic diagrams - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 28 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA = +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. TABLE II. Electrical test requirements. MIL-STD-883 test requirements Interim electrical parameters (method 5004) Subgroups (per method 5005, table I) 1 Final electrical test parameters (method 5004) for programmed devices 1*,2,3,7*,8A, 8B,9 Final electrical test parameters (method 5004) for unprogrammed devices 1*,2,3,7*,8A, 8B Group A test requirements (method 5005) 1,2,3,7,8A,8B,9 10, 11 4/ Groups C and D end-point electrical parameters (method 5005) 1,2,3 1/ * PDA applies to subgroups 1 and 7. 2/ Any or all subgroups may be combined when using high-speed testers. 3/ Subgroups 7, 8A, and 8B functional tests shall also verify that no fuses are blown for unprogrammed devices or that the altered item drawing pattern exists for programmed devices. 4/ Subgroups 10 and 11, if not tested, shall be guaranteed to specified limits in table I. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 29 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, and 6 in table I, method 5005 of MIL-STD-883 shall be omitted. c. For unprogrammed devices, a sample shall be selected to satisfy programmability requirements prior to performing subgroup 9. Twelve devices shall be submitted to programming (see 3.2.2.1). If more than two devices fail to program, the lot shall be rejected. At the manufacturer's option, the sample may be increased to 24 total devices with no more than 4 total device failures allowed. d. For unprogrammed devices, 10 devices from the programmability sample shall be submitted to the requirements of group A, subgroup 9. If more than two devices fail, the lot shall be rejected. At the manufacturer's option, the sample may be increased to 20 total devices with no more than 4 total device failures allowable. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA = +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0540. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103 and QML-38535. The vendors listed in MIL-HDBK-103 and QML-38535 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DLA Land and Maritime-VA. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 84129 A REVISION LEVEL G SHEET 30 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 17-09-27 Approved sources of supply for SMD 84129 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime maintains an online database of all current sources of supply at https://landandmaritimeapps.dla.mil/Programs/Smcr. Standard Microcircuit drawing PIN 1/ 84129013A 8412901JA 8412901KA 8412901LA 8412901XA 84129023A 8412902JA 8412902KA 8412902LA 8412902XA 84129033A 8412903JA 8412903KA 8412903LA 8412903XA 84129043A 8412904JA 8412904KA 8412904LA 8412904XA 84129053A 8412905KA 8412905LA 8412905XA 84129063A 8412906KA 8412906LA 8412906XA 84129073A 8412907KA 8412907LA 8412907XA Vendor CAGE number 3/ 3/ 3/ 3/ 01295 3/ 01295 3/ 3/ 3/ 3/ 01295 3/ 3/ 3/ 3/ 3/ 3/ 01295 3/ 3/ 3/ 3/ 3/ 3/ 01295 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ Vendor similar part 2/ number PAL20L8AML/883B PAL20L8AMJTB PAL20L8AMW/883B TIBPAL20L8-20MWB TIBPAL20L8-20MJTB PAL20L8AMJS/883B TIBPAL20L8-20 PAL20R8AML/883B PAL20R8AMJTB PAL20R8AMW/883B TIBPAL20R8-20MWB TIBPAL20R8-20MJTB PAL20R8AMJS/883B TIBPAL20R8-20 PAL20R6AML/883B PAL20R6AMTJB PAL20R6AMW/883B TIBPAL20R6-20MWB TIBPAL20R6-20MJTB PAL20R6AMJS/883B TIBPAL20R6-20 PAL20R4AML/883B PAL20R4AMJTB PAL20R4AMW/883B TIBPAL20R4-20MWB TIBPAL20R4-20MJTB PAL20R4AMJS/883B TIBPAL20R4-20 PAL20L10AML/883B PAL20L10AMW/883B TIBPAL20L10-25MWB TIBPAL20L10-25MJTB PAL20L10AMJS/883B TIBPAL20L10-25MFKB PAL20X8AML/883B PAL20X8AMW/883B TIBPAL20X8-25MWB TIBPAL20X8-25MJTB PAL20X8AMJS/883B TIBPAL20X8-25MFKB PAL20X10AML/883B PAL20X10AMW/883B TIBPAL20X10-25MWB TIBPAL20X10-25MJTB PAL20X10AMJS/883B TIBPAL20X10-25MFKB See footnotes at end of table. 1 of 2 Reference military specification part number M38510/50501B3A M38510/50501BLA M38510/50502B3A M38510/50502BLA M38510/50503B3A M38510/50503BLA M38510/50504B3A M38510/50504BLA STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 17-09-27 Standard Microcircuit drawing PIN 1/ 84129083A 3/ Vendor similar part 2/ number PAL20X4AML/883B 8412908XA 3/ 3/ 3/ 3/ 3/ PAL20X4AMW/883B TIBPAL20X4-25MWB TIBPAL20X4-25MJTB PAL20X4AMJS/883B TIBPAL20X4-25MFKB 84129093A 8412909KA 3/ 3/ PAL20L8A-2ML/883B PAL20L8A-2MW/883B 8412909LA 3/ PAL20L8A-2MJS/883B 84129103A 3/ PAL20R8A-2ML/883B 8412910KA 3/ PAL20R8A-2MW/883B 8412910LA 3/ PAL20R8A-2MJS/883B 84129113A 3/ PAL20L6A-2ML/883B 8412911KA 3/ PAL20R6A-2MW/883B 8412911LA 3/ PAL20R6A-2MJS/883B 84129123A 3/ PAL20R4A-2ML/883B 8412912KA 3/ PAL20R4A-2MW/883B 8412912LA 3/ PAL20R4A-2MJS/883B 8412908KA 8412908LA Vendor CAGE number Reference military specification part number 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number 01295 Vendor name and address Texas Instruments, Inc. Semiconductor Group 8505 Forest Ln. P O Box 660199 Dallas, TX 75243 Fusible link Titanium-Tungsten The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 2 of 2