High - Q NP0 Chip Capacitors Features * Capacitance available from 0.1 pF to 220 pF. * Available in 0201, 0402, 0603 and 0805 sizes. * Nickel Barrier / Tinned Termination. Characteristics Typical Series Resonant Frequency 0% 30ppm /C, -55C to 125C Dissipation Factor: .0002 (0.02%) max, 25C 0201 Quality Factor: Q > 1,000 @ 1MHz, Typical 10,000 Quality Factor: Q > 5,000 @ 1MHz Ageing: None Insulation Resistance: 1,000 GW @ 25C, 50 mA max 125C IR is 10% of 25C, 50 mA max Dielectric Strength: 2.5 x WVDC Min., 25C, 50 mA max Test Parameters: 1MHz 50kHz, 1.0 0.2 VRMS, 25C Frequency (GHz) 10 Temperature Coefficient: 0201 0402 0603 0805 1 0.1 1 10 100 Capacitance (pF) RF Performance Characteristics 0201, 0402, 0603 & 0805 Maximum ESR 0.25 2.7pF ESR (ohms) 0.20 0402 5.6pF 10pF 47pF 100pf 10pF 0.10 0.05 100 300 500 800 1000 Frequency (MHz) All components in this section are RoHS compliant per the EU directives and definitions. 25 5900 Shepherd Mountain Cove * Austin, TX 78730 Phone: 512 / 794-0081 * Fax: 512 / 794-0087 * Toll Free: 800 / 950-8365 e-mail: sales@venkel.com * www.venkel.com 1000 0402 390pF 330pF 270pF 220pF 180pF 150pF 120pF 82pF 100pF 68pF 56pF 47pF 39pF 33pF 27pF 22pF 20pF 18pF 15pF 12pF 10pF 9.1pF 8.2pF 6.8pF 5.6pF 4.7pF 3.9pF 3.3pF 2.7pF 2.2pF 1.8pF 1.5pF 1.2pF 1.0pF 0.9pF 0.8pF 0.7pF 0.6pF 0.5pF 25V 0.4pF 0201 0.3pF Voltage 0.2pF CASE SIZE 0.1pF Voltage and Capacitance Range 25V 50V 50V 0603 100V 200V 250V 100V 0805 200V 250V Above selection indicates standard product offering. Contact your sales representative for C/V requirements which may not be shown. Mechanical Characteristics L w PHYSICAL DIMENSIONS E/B T Tin Plating Electrodes 0201* 0402 0603 0805 LENGTH .010" .024 .040 .060 .080 (Millimeters) (0.6) (1.020.1) (1.52) (2.03) WIDTH .010" .012 .020 .030 .050 (Millimeters) (0.3) (0.510.1) (0.76) (1.27) THICKNESS MAX .012 .020 .035 .050 (Millimeters) (0.3) (0.510.1) (0.90) (1.27) Silver Base ENDBAND MAX .006 .010 .015 .020 (Millimeters) (0.15) (0.25) (0.38) (.508) Nickel Barrier Layer * 0201 dimensions are .001 How To Order C0805 Series See Chart HQN 201 -- 101 Dielectric Rated Voltage Capacitance Code 250 = 25V (pico - Farads) High - Q NP0 500 = 50v 1st 2 digits 101 = 100v are significant 151 = 150v followed by number 201 = 200v of zeroes. 251 = 250v J N h E Tolerance Termination Marking Packaging Code: N = Nickel barrier, 6 = EIA "J" Code E = Embossed Tape **A = 0.05 pF Tinned Termination "Leave blank if P = Paper Tape *B = 0.1 pF G = Gold over No Marking" *C = 0.25 pF Nickel *D = 0.5 pF Standard termination finish for this product F = 1% is 100% matte Tin (Sn) * 0402 size G = + 2% cannot be J = 5% marked. K = 10% *For capacitance values below 10 pF only **For capacitance values of 1.8 pF or less. 5900 Shepherd Mountain Cove * Austin, TX 78730 Phone: 512 / 794-0081 * Fax: 512 / 794-0087 * Toll Free: 800 / 950-8365 e-mail: sales@venkel.com * www.venkel.com 26