AT88SC1616C Atmel CryptoMemory, 16-Kbit SUMMARY DATASHEET Features * * One of a family of nine devices with user memories from 1-Kbit to 256-Kbit 16-Kbit (2-Kbyte) EEPROM user memory * * * * * Sixteen 128-byte (1-Kbit) zones Self-timed write cycle Single byte or 16-byte page write mode Programmable access rights for each zone 2-Kbit configuration zone * 37-byte OTP area for user-defined codes * 160-byte area for user-defined keys and passwords * High security features * * * * * * * * Smart card features * * * * * * * This is a summary document. The complete document is available on the Atmel website at www.atmel.com. ISO 7816 Class A (5V) or Class B (3V) operation (R) ISO 7816-3 asynchronous T = 0 protocol (Gemplus patent) * Multiple zones, key sets and passwords for multi-application use Synchronous 2-wire serial interface for faster device initialization * Programmable 8-byte answer-to-reset register ISO 7816-2 compliant modules Embedded application features * * * * * * * 64-bit mutual authentication protocol (under license of ELVA) Encrypted checksum Stream encryption Four key sets for authentication and encryption Eight sets of two 24-bit passwords Anti-tearing function Voltage and frequency monitor Low voltage operation: 2.7V to 5.5V Secure nonvolatile storage for sensitive system or user information 2-wire serial interface 1.0MHz compatibility for fast operation Standard 8-lead plastic packages, green compliant (exceeds RoHS) Same pinout as 2-wire Serial EEPROMs High Reliability * Endurance: 100,000 cycles * Data retention: 10 years * ESD protection: 4,000V min * Note: Modules available with either T=0 / 2-wire modes or 2-wire mode only Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 Table 1. Pin Assignment Pad Description ISO Module TWI Module Standard Package Pin VCC Supply Voltage C1 C1 8 GND Ground C5 C5 4 SCL/CLK Serial Clock Input C3 C3 6 SDA/IO Serial Data Input/Output C7 C7 5 RST Reset Input C2 NC NC Figure 1. Pin Configuration ISO Smart Card Module VCC=C1 RST=C2 SCL/CLK=C3 NC=C4 C5=GND C6=NC C7=SDA/IO C8=NC 8-lead SOIC, PDIP NC NC NC 1 8 VCC 2 7 3 6 NC SCL GND 4 5 SDA TWI Smart Card Module VCC=C1 NC=C2 SCL/CLK=C3 NC=C4 1. C5=GND C6=NC C7=SDA/IO C8=NC Description (R) (R) The Atmel AT88SC1616C member of the Atmel CryptoMemory family is a high-performance secure memory providing 16-Kbits of user memory with advanced security and cryptographic features built in. The user memory is divided into 16 128byte zones, each of which may be individually set with different security access rights or effectively combined together to provide space for 1 to 16 data files. 1.1 Smart Card Applications The AT88SC1616C provides high security, low cost, and ease of implementation without the need for a microprocessor operating system. The embedded cryptographic engine provides for dynamic and symmetric mutual authentication between the device and host, as well as performing stream encryption for all data and passwords exchanged between the device and host. Up to four unique key sets may be used for these operations. The AT88SC1616C offers the ability to communicate with virtually any smart card reader using the asynchronous T = 0 protocol (Gemplus patent) defined in ISO 7816-3. 1.2 Embedded Applications Through dynamic and symmetric mutual authentication, data encryption, and the use of encrypted checksums, the AT88SC1616C provides a secure place for storage of sensitive information within a system. With its tamper detection circuits, this information remains safe even under attack. A 2-wire serial interface running at 1.0MHz is used for fast and efficient communications with up to 15 devices that may be individually addressed. The AT88SC1616C is available in industry standard 8-lead packages with the same familiar pinout as 2-wire serial EEPROMs. 2 AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 Figure 1-1. Block Diagram Power Management Authentication, Encryption and Certification Unit Synchronous Interface Data Transfer Asynchronous ISO Interface Password Verification Reset Block Answer to Reset VCC GND SCL/CLK SDA/IO RST 2. Pin Descriptions 2.1 Supply Voltage (VCC) Random Generator EEPROM The VCC input is a 2.7V to 5.5V positive voltage supplied by the host. 2.2 Clock (SCL/CLK) In the asynchronous T = 0 protocol, the SCL/CLK input is used to provide the device with a carrier frequency f. The nominal length of one bit emitted on I/O is defined as an "elementary time unit" (ETU) and is equal to 372/f. When the synchronous protocol is used, the SCL/CLK input is used to positive edge clock data into the device and negative edge clock data out of the device. 2.3 Reset (RST) The AT88SC1616C provides an ISO 7816-3 compliant asynchronous answer to reset sequence. When the reset sequence is activated, the device will output the data programmed into the 64-bit answer-to-reset register. An internal pull-up on the RST input pad allows the device to be used in synchronous mode without bonding RST. The AT88SC1616C does not support the synchronous answer-to-reset sequence. 2.4 Serial Data (SDA/IO) The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wired with any number of other open drain or open collector devices. An external pull-up resistor should be connected between SDA and VCC. The value of this resistor and the system capacitance loading the SDA bus will determine the rise time of SDA. This rise time will determine the maximum frequency during read operations. Low value pull-up resistors will allow higher frequency operations while drawing higher average power. SDA/IO information applies to both asynchronous and synchronous protocols. When the synchronous protocol is used, the SCL/CLK input is used to positive edge clock data into the device and negative edge clock data out of the device. AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 3 3. Absolute Maximum Ratings* Operating temperature.................... -40C to +85C *Notice: Storage temperature ................... -65C to + 150C Voltage on any pin with respect to ground ...............- 0.7 to VCC +0.7V Maximum operating voltage ............................. 6.0V DC output current ......................................... 5.0mA Table 3-1. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other condition beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect device reliability. DC Characteristics Applicable over recommended operating range from VCC = +2.7 to 5.5V, TAC = -40C to +85C (unless otherwise noted) Symbol Parameter (2) VCC Supply Voltage ICC Supply Current (VCC = 5.5V) ICC Max Units 5.5 V Async Read at 3.57MHz 5 mA Supply Current (VCC = 5.5V) Async Write at 3.57MHz 5 mA ICC Supply Current (VCC = 5.5V) Synch Read at 1MHz 5 mA ICC Supply Current (VCC = 5.5V) Synch Write at 1MHz 5 mA ISB Min Standby Current (VCC = 5.5V) VIN = VCC or GND 100 A 2.7 Typ VIL (1) SDA/IO Input Low Threshold 0 VCC x 0.2 V VIL (1) SCL/CLK Input Low Threshold 0 VCC x 0.2 V VIL (1) RST Input Low Threshold 0 VCC x 0.2 V VIH (1)(2) SDA/IO Input High Threshold VCC x 0.7 VCC V (1)(2) VIH SCL/CLK Input High Threshold VCC x 0.7 VCC V (1)(2) VIH RST Input High Threshold VCC x 0.7 VCC V IIL SDA/IO Input Low Current 0 < VIL < VCC x 0.15 15 A IIL SCL/CLK Input Low Current 0 < VIL < VCC x 0.15 15 A IIL RST Input Low Current 0 < VIL < VCC x 0.15 50 A IIH SDA/IO Input High Current VCC x 0.7 < VIH < VCC 20 A IIH SCL/CLK Input High Current VCC x 0.7 < VIH < VCC 100 A IIH RST Input High Current VCC x 0.7 < VIH < VCC 150 A VOH SDA/IO Output High Voltage 20K ohm external pull-up VCC x 0.7 VCC V VOL SDA/IO Output Low Voltage IOL = 1mA 0 VCC x 0.15 V IOH SDA/IO Output High Current VOH 20 A Notes: 4 Test Condition 1. VIL min and VIH max are reference only and are not tested 2. To prevent latch up conditions from occurring during power up of the AT88SCxxxxC, VCC must be turned on before applying VIH. For powering down, VIH must be removed before turning VCC off AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 Table 3-2. AC Characteristics Applicable over recommended operating range from VCC = +2.7 to 5.5V, TAC = -40C to +85C, CL = 30pF (unless otherwise noted) 4. Symbol Parameter Min Max Units fCLK Async Clock Frequency (VCC Range: +4.5 - 5.5V) 1 5 MHZ fCLK Async Clock Frequency (VCC Range: +2.7 - 3.3V) 1 4 MHZ fCLK Synch Clock Frequency 0 1 MHZ Clock Duty cycle 40 60 % tR Rise Time - I/O, RST 1 S tF Fall Time - I/O, RST 1 S tR Rise Time - CLK 9% x period S tF Fall Time - CLK 9% x period S tAA Clock Low to Data Out Valid 35 nS tHD.STA Start Hold Time 200 nS tSU.STA Start Set-up Time 200 nS tHD.DAT Data In Hold Time 10 nS tSU.DAT Data In Set-up Time 100 nS tSU.STO Stop Set-up Time 200 nS tDH Data Out Hold Time 20 nS tWR Write Cycle Time (at 25 C) 5 mS tWR Write Cycle Time (-40 to +85C) 7 mS Device Operation for Synchronous Protocols Clock and Data Transitions: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see Figure 4-3 on page 7). Data changes during SCL high periods will indicate a start or stop condition as defined below. Start Condition: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (see Figure 4-4 on page 7). Stop Condition: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (see Figure 4-4 on page 7). Acknowledge: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle (see Figure 4-5 on page 7). Memory Reset: After an interruption in protocol, power loss or system reset, any 2-wire part can be reset by following these steps: 1. 2. 3. Clock up to nine cycles Look for SDA high in each cycle while SCL is high Create a start condition AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 5 Figure 4-1. Bus Timing for 2-wire Communications SCL: Serial Clock, SDA - Serial Data I/O tHIGH tF tR tLOW SCL tSU.STA tLOW tHD.STA tHD.DAT tSU.STO tSU.DAT SDA IN tAA tDH tBUF SDA OUT Figure 4-2. Write Cycle Timing: SCL Serial Clock, SDA - Serial Data I/O SCL SDA 8th BIT ACK WORDn twr STOP CONDITION Note: 6 (1) START CONDITION The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 Figure 4-3. Data Validity SDA SCL DATA STABLE DATA STABLE DATA CHANGE ALLOWED Figure 4-4. Start and Stop Definitions SDA SCL START STOP Figure 4-5. Output Acknowledge 1 SCL 8 9 DATA IN DATA OUT START ACKNOWLEDGE AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 7 5. Device Architecture 5.1 User Zones The EEPROM user memory is divided into 16 zones of 1024 bits each. Multiple zones allow for different types of data or files to be stored in different zones. Access to the user zones is allowed only after security requirements have been met. These security requirements are defined by the user during the personalization of the device in the configuration memory. If the same security requirements are selected for multiple zones, then these zones may effectively be accessed as one larger zone. Figure 5-1. User Zones Zone User 0 $0 $1 $2 $3 $4 $5 $6 $7 $00 128 bytes $78 User 1 User 14 $00 User 15 $00 $78 128 bytes $78 6. Control Logic Access to the user zones occurs only through the control logic built into the device. This logic is configurable through access registers, key registers and keys programmed into the configuration memory during device personalization. Also implemented in the control logic is a cryptographic engine for performing the various higher-level security functions of the device. 8 AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 7. Configuration Memory The configuration memory consists of 2048 bits of EEPROM memory used for storing passwords, keys and codes and for defining security levels to be used for each user zone. Access rights to the configuration memory are defined in the control logic and may not be altered by the user. Figure 7-1. Configuration Memory $0 $1 $2 $3 $00 $08 $4 $5 $6 $7 Answer to Reset Fab Code MTZ $10 Identification Card Manufacturer Code Lot History Code Read Only $18 DCR Identification Number Nc $20 AR0 PR0 AR1 PR1 AR2 PR2 AR3 PR3 $28 AR4 PR4 AR5 PR5 AR6 PR6 AR7 PR7 $30 AR8 PR8 AR9 PR9 AR10 PR10 AR11 PR11 $38 AR12 PR12 AR13 PR13 AR14 PR14 AR15 PR15 $40 Access Control Issuer Code $48 $50 $58 $60 $68 $70 For Authentication and Encryption Use Cryptography For Authentication and Encryption Use Secret $78 $80 $88 $90 $98 $A0 $A8 $B0 PAC Write 0 PAC Read 0 $B8 PAC Write 1 PAC Read 1 $C0 PAC Write 2 PAC Read 2 $C8 PAC Write 3 PAC Read 3 $D0 PAC Write 4 PAC Read 4 $D8 PAC Write 5 PAC Read 5 $E0 PAC Write 6 PAC Read 6 $E8 PAC Write 7 PAC Read 7 $F0 $F8 Reserved Password Forbidden AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 9 8. Security Fuses There are three fuses on the device that must be blown during the device personalization process. Each fuse locks certain portions of the configuration memory as OTP memory. Fuses are designed for the module manufacturer, card manufacturer and card issuer and should be blown in sequence, although all programming of the device and blowing of the fuses may be performed at one final step. 9. Protocol Selection The AT88SC1616C supports two different communication protocols. * Smart Card Applications: The asynchronous T = 0 protocol defined by ISO 7816-3 is used for compatibility with the industry's standard smart card readers * Embedded Applications: A 2-wire serial interface is used for fast and efficient communication with logic or controllers The power-up sequence determines which of the two communication protocols will be used. 9.1 Asynchronous T = 0 Protocol This power-up sequence complies with ISO 7816-3 for a cold reset in smart card applications. * * * * VCC goes high; RST, I/O-SDA and CLK-SCL are low Set I/O-SDA in receive mode Provide a clock signal to CLK-SCL RST goes high after 400 clock cycles The device will respond with a 64-bit ATR code, including historical bytes to indicate the memory density within the CryptoMemory family. Once the asynchronous mode has been selected, it is not possible to switch to the synchronous mode without powering off the device. Figure 9-1. Asynchronous T = 0 Protocol (Gemplus Patent) Vcc I/O-SDA RST CLK-SCL 10 AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 ATR 9.2 Synchronous 2-wire Serial Interface The synchronous mode is the default after powering up VCC due to an internal pull-up on RST. For embedded applications using CryptoMemory in standard plastic packages, this is the only communication protocol. * * Power-up VCC, RST goes high also After stable VCC, CLK-SCL and I/O-SDA may be driven Figure 9-2. Synchronous 2-wire Protocol Vcc I/O-SDA RST 1 CLK-SCL Note: 10. 2 4 3 5 Five clock pulses must be sent before the first command is issued Communication Security Modes Communications between the device and host operate in three basic modes. Standard mode is the default mode for the device after power-up. Authentication mode is activated by a successful authentication sequence. Encryption mode is activated by a successful encryption activation following a successful authentication. Table 10-1. Communication Security Modes Mode (1) Configuration Data User Data Passwords Data Integrity Check Standard Clear Clear Clear MDC Authentication Clear Clear Encrypted MAC Encryption Clear Encrypted Encrypted MAC Notes: 1. Configuration data include viewable areas of the configuration zone except the passwords: MDC: Modification Detection Code MAC: Message Authentication Code AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 11 11. Security Options 11.1 Anti-tearing In the event of a power loss during a write cycle, the integrity of the device's stored data may be recovered. This function is optional - the host may choose to activate the anti-tearing function, depending on application requirements. When anti-tearing is active, write commands take longer to execute, since more write cycles are required to complete them, and data are limited to eight bytes. Data are written first to a buffer zone in EEPROM instead of the intended destination address, but with the same access conditions. The data are then written in the required location. If this second write cycle is interrupted due to a power loss, the device will automatically recover the data from the system buffer zone at the next power-up. In 2-wire mode, the host is required to perform ACK polling for up to 8mS after write commands when anti-tearing is active. At power-up, the host is required to perform ACK polling, in some cases for up to 2mS, in the event that the device needs to carry out the data recovery process. 11.2 Write Lock If a user zone is configured in the write lock mode, the lowest address byte of an 8-byte page constitutes a write access byte for the bytes of that page. Example: The write lock byte at $080 controls the bytes from $080 to $087 Table 11-1. Write Lock Example Address $080 $0 $1 $2 $3 $4 $5 $6 $7 11011001 xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx locked locked locked The write lock byte may also be locked by writing its least significant (rightmost) bit to "0". Moreover, when write lock mode is activated, the write lock byte can only be programmed - that is, bits written to "0" cannot return to "1". In the write lock configuration, only one byte can be written at a time. Even if several bytes are received, only the first byte will be taken into account by the device. 12 AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 12. Password Verification Passwords may be used to protect read and/or write access of any user zone. When a valid password is presented, it is memorized and active until power is turned off, unless a new password is presented or RST becomes active. There are eight password sets that may be used to protect any user zone. Only one password is active at a time, but write passwords give read access also. 12.1 Authentication Protocol The access to a user zone may be protected by an authentication protocol. Any one of four keys may be selected to use with a user zone. The authentication success is memorized and active as long as the chip is powered, unless a new authentication is initialized or RST becomes active. If the new authentication request is not validated, the card loses its previous authentication and it should be presented again. Only the last request is memorized. Note: Password and authentication may be presented at any time and in any order. If the trials limit has been reached (after four consecutive incorrect attempts), the password verification or authentication process will not be taken into account Figure 12-1. Password and Authentication Operations Host (Reader) Device (Card) Card Number AUTHENTICATION Challenge A VERIFY A COMPUTE Challenge B VERIFY B Challenge B VERIFY RPW DATA Checksum (CS) VERIFY WPW VERIFY CS COMPUTE Challenge A READ ACCESS Read Password (RPW) VERIFY CS WRITE ACCESS Write Password (WPW) DATA CS Write DATA AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 13 12.2 Checksum The AT88SC1616C implements a data validity check function in the form of a checksum, which may function in standard, authentication or encryption modes. In the standard mode, the checksum is implemented as a Modification Detection Code (MDC), in which the host may read an MDC from the device in order to verify that the data sent was received correctly. In the authentication and encryption modes, the checksum becomes more powerful since it provides a bidirectional data integrity check and data origin authentication capability in the form of a Message Authentication Code (MAC). Only the host/device that carried out a valid authentication is capable of computing a valid MAC. While operating in the authentication or encryption modes, the use of a MAC is required. For an ingoing command, if the device calculates a MAC different from the MAC transmitted by the host, not only is the command abandoned but the mode is also reset. A new authentication and/or encryption activation will be required to reactivate the MAC. 12.3 Encryption The data exchanged between the device and the host during read, write and verify password commands may be encrypted to ensure data confidentiality. The issuer may choose to require encryption for a user zone by settings made in the configuration memory. Any one of four keys may be selected for use with a user zone. In this case, activation of the encryption mode is required in order to read/write data in the zone and only encrypted data will be transmitted. Even if not required, the host may elect to activate encryption provided the proper keys are known. 12.4 Supervisor Mode Enabling this feature allows the holder of one specific password to gain full access to all eight password sets, including the ability to change passwords. 12.5 Modify Forbidden No write access is allowed in a user zone protected with this feature at any time. The user zone must be written during device personalization prior to blowing the security fuses. 12.6 Program Only For a user zone protected by this feature, data within the zone may be changed from a "1" to a "0", but never from a "0" to a "1". 13. Initial Device Programming To enable the security features of CryptoMemory, the device must first be personalized to set up several registers and load in the appropriate passwords and keys. This is accomplished through programming the configuration memory of CryptoMemory using simple write and read commands. To gain access to the configuration memory, the secure code must first be successfully presented. For the AT88SC1616C device, the secure code is $20 0C E0. After writing and verifying data in the configuration memory, the security fuses must be blown to lock this information in the device. For additional information on personalizing CryptoMemory, please see the application notes Programming CryptoMemory for Embedded Applications and Initializing CryptoMemory for Smart Card Applications (at www.Atmel.com). 14 AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 14. Ordering Information Atmel Ordering Code Package Voltage Range Temperature Range AT88SC1616C-MJ AT88SC1616C-MP AT88SC1616C-MJTG AT88SC1616C-MPTG M2 - J Module - ISO M2 - P Module - ISO M2 - J Module - TWI M2 - P Module - TWI 2.7V-5.5V Commercial (0C-70C) AT88SC1616C-PU AT88SC1616C-SH 8P3 8S1 2.7V-5.5V Green compliant (exceeds RoHS) Industrial (-40C-85C) AT88SC1616C-WI 7 mil wafer 2.7V-5.5V Industrial (-40C-85C) Package Type (1) (2) Description M2 - J Module : ISO or TWI M2 ISO 7816 smart card module M2 - P Module : ISO or TWI M2 ISO 7816 smart card module with Atmel logo 8P3 8-lead, 0.300" wide, Plastic Dual Inline (PDIP) 8S1 8-lead, 0.150" wide, Plastic Gull Wing Small Outline (JEDEC SOIC) Notes: (R) 1. Formal drawings may be obtained from an Atmel sales office 2. Both the J and P module packages are used for either ISO (T=0 / 2-wire mode) or TWI (2-wire mode only) AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 15 15. Packaging Information Ordering Code: MJ or MJTG Module Size: Dimension*: Glob Top: Thickness: Pitch: Note: 16 Ordering Code: MP or MPTG M2 12.6 x 11.4 [mm] Round - 8.5 [mm] 0.58 [mm] 14.25mm Module Size: M2 Dimension*: Glob Top: Thickness: Pitch: 12.6 x 11.4 [mm] Square - 8.8 x 8.8 [mm] 0.58 [mm] 14.25mm *The module dimensions listed refer to the dimensions of the exposed metal contact area. The actual dimensions of the module after excise or punching from the carrier tape are generally 0.4mm greater in both directions (i.e., a punched M2 module will yield 13.0 x 11.8mm) AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 15.1 Atmel AT88SC1616C Package Marking Information AT88SC1616C: Package Marking Information 8-lead PDIP 8-lead SOIC AT88SC 1616C U YYWW AT88SC 1616C H YMXX @ No Bottom side mark (this package) Note 1: designates pin 1 Note 2: Package drawings are not to scale Date Codes YY = Year 12: 2012 13: 2013 14: 2014 15: 2015 Grade/Lead Finish Material WW = Work Week of Assembly 02:Week 2 04:Week 4 ... 52:Week 52 Y = Year 2: 2012 3: 2013 4: 2014 5: 2015 M = Month A = January B = February ... L = December Country of Assembly Lot Number @ = Country of Assembly Marked on Bottom side unless in Injector Mold for PDI P only! Marked on Bottom side for the PDI P only! U: H: Industrial/Matte Tin Industrial/NiPdAu Atmel Truncation AT: Atmel Trace Code XX = Trace Code (Atmel Lot Numbers to Correspond to Code) Example: AA, AB.... YZ, ZZ 3/5/12 TITLE Package Mark Contact: DL-CSO-Assy_eng@atmel.com 88SC1616CSM, AT88SC1616C Package Marking Information DRAWING NO. REV. 88SC1616CSM A AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 17 15.2 Ordering Code: SH 8S1 - 8-lead JEDEC SOIC C 1 E E1 L N O TOP VIEW e END VIEW b COMMON DIMENSIONS (Unit of Measure = mm) A A1 D SIDE VIEW Notes: This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. SYMBOL MIN A 1.35 NOM MAX - 1.75 A1 0.10 - 0.25 b 0.31 - 0.51 C 0.17 - 0.25 D 4.80 - 5.05 E1 3.81 - 3.99 E 5.79 - 6.20 e L NOTE 1.27 BSC 0.40 - 1.27 0 - 8 6/22/11 Package Drawing Contact: packagedrawings@atmel.com 18 TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 GPC SWB DRAWING NO. REV. 8S1 G 15.3 Ordering Code: PU 8P3 - 8-lead PDIP E 1 E1 N Top View c eA End View D D1 COMMON DIMENSIONS (Unit of Measure = inches) e SYMBOL A2 A b2 b3 L Side View 1. 2. 3. 4. 5. 6. 0.210 NOTE 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 D1 0.005 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 0.100 BSC eA 0.300 BSC 0.115 3 3 e L Notes: MAX NOM A b 4 PLCS MIN 0.130 4 0.150 2 This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. E and eA measured with the leads constrained to be perpendicular to datum. Pointed or rounded lead tips are preferred to ease insertion. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm). 06/21/11 Package Drawing Contact: packagedrawings@atmel.com TITLE GPC DRAWING NO. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) PTC 8P3 AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 REV. D 19 16. 20 Revision History Doc. Rev. Date Comments 2030MS 12/2013 Add package marking information. Update Atmel logos and disclaimer page. 2030LS 12/2011 Update template. Update package drawings. Change AT88SC1616C-SU to AT88SC1616C-SH. 2030KS 10/2009 Features Section - add `Green compliant (exceeds RoHS) to end of `Standard 8-lead Plastic Packages' bullet added Note to DC Characteristics table and applied to VCC and all 3 instances of Vih symbols in table. Ordering Information page: Add `Green compliant (exceeds RoHS) to middle row of Temperature Range Replace `Lead-free/Halogen-free. Keep industrial. Updated to 2009 Copyright. SB - TWI Package update. 2030JS 11/2008 Removed P module offering. 2030IS 04/2007 Updated timing diagrams. 2030IS 01/2007 Final release version. 2030IS 01/2007 Replaced User Zone, Configuration Memory, and Write Lock. Example tables with new information. AT88SC1616C [SUMMARY DATASHEET] Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013 Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 www.atmel.com (c) 2013 Atmel Corporation. / Rev.: Atmel-2030MS-CryptoMem-AT88SC1616C-Datasheet-Summary_122013. Atmel(R), Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. ARM(R), ARM Connected(R) logo, and others are the registered trademarks or trademarks of ARM Ltd. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death ("Safety-Critical Applications") without an Atmel officer's specific written consent. SafetyCritical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.