VS-ST730CL Series
www.vishay.com Vishay Semiconductors
Revision: 28-Sep-17 1Document Number: 94414
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Phase Control Thyristors
(Hockey PUK Version), 990 A
FEATURES
Center amplifying gate
Metal case with ceramic insulator
International standard case B-PUK (TO-200AC)
Designed and qualified for industrial level
Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
TYPICAL APPLICATIONS
DC motor controls
Controlled DC power supplies
AC controllers
PRIMARY CHARACTERISTICS
IT(AV) 990 A
VDRM/VRRM 800 V, 1200 V, 1400 V, 1600 V,
1800 V, 2000 V
VTM 1.62 V
IGT 100 mA
TJ-40 °C to +125 °C
Package B-PUK (TO-200AC)
Circuit configuration Single SCR
B-PUK (TO-200AC)
MAJOR RATINGS AND CHARACTERISTICS
PARAMETER TEST CONDITIONS VALUES UNITS
IT(AV)
990 A
Ths 55 °C
IT(RMS)
2000 A
Ths 25 °C
ITSM
50 Hz 17 800 A
60 Hz 18 700
I2t50 Hz 1591 kA2s
60 Hz 1452
VDRM/VRRM 800 to 2000 V
tqTypical 150 μs
TJ-40 to 125 °C
VOLTAGE RATINGS
TYPE
NUMBER
VOLTAGE
CODE
VDRM/VRRM, MAXIMUM REPETITIVE
PEAK AND OFF-STATE VOLTAGE
V
VRSM, MAXIMUM
NON-REPETITIVE PEAK VOLTAGE
V
IDRM/IRRM MAXIMUM AT
TJ = TJ MAXIMUM
mA
VS-ST730CL
08 800 900
80
12 1200 1300
14 1400 1500
16 1600 1700
18 1800 1900
20 2000 2100
VS-ST730CL Series
www.vishay.com Vishay Semiconductors
Revision: 28-Sep-17 2Document Number: 94414
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ABSOLUTE MAXIMUM RATINGS
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum average on-state current
at heatsink temperature IT(AV) 180° conduction, half sine wave
double side (single side) cooled
990 (375) A
55 (85) °C
Maximum RMS on-state current IT(RMS) DC at 25 °C heatsink temperature double side cooled 2000
A
Maximum peak, one-cycle
non-repetitive surge current ITSM
t = 10 ms No voltage
reapplied
Sinusoidal half wave,
initial TJ = TJ maximum
17 800
t = 8.3 ms 18 700
t = 10 ms 100 % VRRM
reapplied
15 000
t = 8.3 ms 15 700
Maximum I2t for fusing I2t
t = 10 ms No voltage
reapplied
1591
kA2s
t = 8.3 ms 1452
t = 10 ms 100 % VRRM
reapplied
1125
t = 8.3 ms 1027
Maximum I2t for fusing I2t t = 0.1 to 10 ms, no voltage reapplied 15 910 kA2s
Low level value of threshold voltage VT(TO)1 (16.7 % x x IT(AV) < I < x IT(AV)), TJ = TJ maximum 0.98 V
High level value of threshold voltage VT(TO)2 (I > x IT(AV)), TJ = TJ maximum 1.12
Low level value of on-state slope resistance rt1 (16.7 % x x IT(AV) < I < x IT(AV)), TJ = TJ maximum 0.32 m
High level value of on-state slope resistance rt2 (I > x IT(AV)), TJ = TJ maximum 0.27
Maximum on-state voltage VTM Ipk = 2000 A, TJ = TJ maximum, tp = 10 ms sine pulse 1.62 V
Maximum holding current IHTJ = 25 °C, anode supply 12 V resistive load 600 mA
Typical latching current IL1000
SWITCHING
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum non-repetitive rate of rise
of turned-on current dI/dt Gate drive 20 V, 20 , tr 1 μs
TJ = TJ maximum, anode voltage 80 % VDRM 1000 A/μs
Typical delay time tdGate current 1 A, dIg/dt = 1 A/μs
Vd = 0.67 % VDRM, TJ = 25 °C 1.0
μs
Typical turn-off time tqITM = 750 A, TJ = TJ maximum, dI/dt = 60 A/μs,
VR = 50 V, dV/dt = 20 V/μs, gate 0 V 100 , tp = 500 μs 150
BLOCKING
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum critical rate of rise of
off-state voltage dV/dt TJ = TJ maximum linear to 80 % rated VDRM 500 V/μs
Maximum peak reverse and
off-state leakage current
IRRM,
IDRM TJ = TJ maximum, rated VDRM/VRRM applied 80 mA
VS-ST730CL Series
www.vishay.com Vishay Semiconductors
Revision: 28-Sep-17 3Document Number: 94414
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
The table above shows the increment of thermal resistance RthJ-hs when devices operate at different conduction angles than DC
TRIGGERING
PARAMETER SYMBOL TEST CONDITIONS
VALUES UNITS
Typ. Max.
Maximum peak gate power PGM TJ = TJ maximum, tp 5 ms 10.0 W
Maximum average gate power PG(AV) TJ = TJ maximum, f = 50 Hz, d% = 50 2.0
Maximum peak positive gate current IGM TJ = TJ maximum, tp 5 ms 3.0 A
Maximum peak positive gate voltage + VGM TJ = TJ maximum, tp 5 ms 20 V
Maximum peak negative gate voltage - VGM 5.0
DC gate current required to trigger IGT
TJ = -40 °C
Maximum required gate
trigger/
current/voltage are the lowest
value which will trigger all units
12 V anode to cathode applied
200 -
mATJ = 25 °C 100 200
TJ = 125 °C 50 -
DC gate voltage required to trigger VGT
TJ = -40 °C 2.5 -
V
TJ = 25 °C 1.8 3.0
TJ = 125 °C 1.1 -
DC gate current not to trigger IGD
TJ = TJ maximum
Maximum gate current/voltage
not to trigger is the maximum
value which will not trigger any
unit with rated VDRM anode to
cathode applied
10 mA
DC gate voltage not to trigger VGD 0.25 V
THERMAL AND MECHANICAL SPECIFICATIONS
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum operating junction temperature range TJ-40 to 125 °C
Maximum storage temperature range TStg -40 to 150
Maximum thermal resistance, junction to heatsink RthJ-hs
DC operation single side cooled 0.073
K/W
DC operation double side cooled 0.031
Maximum thermal resistance, case to heatsink RthC-hs
DC operation single side cooled 0.011
DC operation double side cooled 0.006
Mounting force, ± 10 % 14 700
(1500)
N
(kg)
Approximate weight 255 g
Case style See dimensions - link at the end of datasheet B-PUK (TO-200AC)
RthJ-hs CONDUCTION
CONDUCTION ANGLE SINUSOIDAL CONDUCTION RECTANGULAR CONDUCTION TEST CONDITIONS UNITS
SINGLE SIDE DOUBLE SIDE SINGLE SIDE DOUBLE SIDE
180° 0.009 0.009 0.006 0.006
TJ = TJ maximum K/W
120° 0.011 0.011 0.010 0.011
90° 0.014 0.014 0.015 0.015
60° 0.020 0.020 0.021 0.021
30° 0.036 0.036 0.036 0.036
VS-ST730CL Series
www.vishay.com Vishay Semiconductors
Revision: 28-Sep-17 4Document Number: 94414
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Fig. 1 - Current Ratings Characteristics
Fig. 2 - Current Ratings Characteristics
Fig. 3 - Current Ratings Characteristics
Fig. 4 - Current Ratings Characteristics
Fig. 5 - On-State Power Loss Characteristics
Fig. 6 - On-State Power Loss Characteristics
40
50
60
70
80
90
100
110
120
130
0 100200300400500600700
30° 60°
90°
120°
180°
Average On-state Current (A)
Conduction Angle
Maximum Allowable Heatsink Temperature (°C)
ST7 3 0 C . . L Se r i e s
(Single Side Cooled)
R (DC) = 0.073 K/ W
thJ-hs
20
30
40
50
60
70
80
90
100
110
120
130
020040060080010001200
DC
30°
60°
90°
120°
180°
Average On-state Current (A)
Conduc tion Period
Maximum Allowable Heatsink Temperature (°C)
ST730C..L Series
(Single Side Cooled)
R (DC) = 0.073 K/ W
thJ-hs
20
30
40
50
60
70
80
90
100
110
120
130
0 200 400 600 800 1000 1200 1400
30° 60° 90° 120° 180°
Conduction Angle
Maximum Allowable Heatsink TemperatureC)
ST7 3 0 C . . L Se r i e s
(Double Side Cooled)
R (DC) = 0.031 K/ W
thJ-hs
20
30
40
50
60
70
80
90
100
110
120
130
0 400 800 1200 1600 2000 2400
DC
30°
60°
90°
120°180°
Avera g e On-st a te Current (A)
Conduction Period
Maximum Allowable Heatsink Temperature (°C)
ST7 3 0 C . . L Se r i e s
(Double Side Cooled)
R (DC) = 0.031 K/ W
thJ-hs
0
500
1000
1500
2000
2500
0 200 400 600 800 1000 1200 1400
180°
120°
90°
60°
30° RM S Li m i t
Conduc tion Angle
Maximum Average On-state Power Loss (W)
Average On-state Current (A)
ST730C..L Series
T = 125°C
J
0
500
1000
1500
2000
2500
3000
3500
0 400 800 1200 1600 2000 2400
DC
180°
120°
90°
60°
30°
RM S Lim i t
Conduction Period
Maximum Average On-state Power Loss (W)
Average On-sta te Current (A)
ST730C..L Series
T = 1 2 5 ° C
J
VS-ST730CL Series
www.vishay.com Vishay Semiconductors
Revision: 28-Sep-17 5Document Number: 94414
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Fig. 7 - Maximum Non-Repetitive Surge Current
Single and Double Side Cooled
Fig. 8 - Maximum Non-Repetitive Surge Current
Single and Double Side Cooled
Fig. 9 - On-State Voltage Drop Characteristics
Fig. 10 - Thermal Impedance ZthJ-hs Characteristics
7000
8000
9000
10000
11000
12000
13000
14000
15000
16000
110100
Number Of Equal Amplitude Half Cycle Current Pulses (N)
Peak Ha lf Sine Wave On-state Current (A)
Initia l T = 125°C
@ 60 Hz 0.0083 s
@ 50 Hz 0.0100 s
J
ST7 3 0 C . . L Se r i e s
At Any Rated Load Condition And With
Rated V Applied Following Surge.
RRM
7000
8000
9000
10000
11000
12000
13000
14000
15000
16000
17000
18000
0.01 0.1 1
Pulse Train Duration (s)
Ve rsus Pulse Train Dura t ion. Contro l
Peak Half Sine Wave On-state Current (A)
Init ial T = 125°C
No Voltage Reapplied
Ra t e d V Re a p p l i e d
RRM
J
ST7 3 0 C . . L Se r i e s
Maximum Non Repetitive Surge Current
Of Conduction May Not Be Maintained.
100
1000
10000
0.5 1 1.5 2 2.5 3 3.5
T = 2 5 ° C
J
Instantaneous On-state Current (A)
Instantaneous On-state Voltage (V)
T = 125°C
J
ST7 3 0 C . . L Se r i e s
0.001
0.01
0.1
0.001 0.01 0.1 1 10
Sq u a r e W a v e Pu l se D u r a t i o n ( s)
thJ-hs
Steady State Value
R = 0.073 K/ W
(Single Side Cooled)
R = 0.031 K/ W
(Double Side Cooled)
(DC Operation)
thJ-hs
thJ-hs
ST7 3 0 C . . L Se r i e s
Transient Thermal Impedance Z (K/W)
VS-ST730CL Series
www.vishay.com Vishay Semiconductors
Revision: 28-Sep-17 6Document Number: 94414
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Fig. 11 - Gate Characteristics
ORDERING INFORMATION TABLE
0.1
1
10
100
0.001 0.01 0.1 1 10 100
VGD
IGD
(b)
(a)
Tj = 2 5 ° C
Tj = 12 5 ° C
Tj = - 4 0 ° C
(2) (3)
Instantaneous Gate Current (A)
In st a n t a n e o u s G a t e V o lt a g e ( V )
a) Recommended load line for
b) Recommended load line for
<=30% rated di/ d t : 10V, 10ohms
Fre q u e n c y Lim it e d b y PG ( A V )
rated di/dt : 20V, 10ohms; tr<=1 µs
tr<=1 µs
(1)
(1) PGM = 10W, tp = 4ms
(2) PGM = 20W, tp = 2ms
(3) PGM = 40W, tp = 1ms
(4) PGM = 60W, tp = 0.66ms
Rectangular gate pulse
Device: ST730C..L Series
(4)
- Thyristor
2
- Essential part number
3
- 0 = converter grade
4
- C = ceramic PUK
5
- Voltage code x 100 = VRRM (see Voltage Ratings table)
6
- L = PUK case B-PUK (TO-200AC)
7
- 0 = eyelet terminals (gate and auxiliary cathode unsoldered leads)
1 = fast-on terminals (gate and auxiliary cathode unsoldered leads)
2 = eyelet terminals (gate and auxiliary cathode soldered leads)
9
8
- Critical dV/dt: None = 500 V/µs (standard selection)
L = 1000 V/µs (special selection)
3 = fast-on terminals (gate and auxiliary cathode soldered leads)
Device code
51 32 4 6 7 8 9
STVS- 73 0 C 20 L 1 -
1- Vishay Semiconductors product
LINKS TO RELATED DOCUMENTS
Dimensions www.vishay.com/doc?95076
Outline Dimensions
www.vishay.com Vishay Semiconductors
Revision: 12-Jul-17 1Document Number: 95076
For technical questions within your region: DiodesAmericass@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
B-PUK (TO-200AC)
DIMENSIONS in millimeters (inches)
Pin receptacle
AMP. 60598-1
0.7 (0.03) MIN. 34 (1.34) DIA. MAX.
2 places
53 (2.09) DIA. MAX.
58.5 (2.3) DIA. MAX.
2 holes DIA. 3.5 (0.14) x 2.5 (0.1) deep
4.7 (0.18)
27 (1.06) MAX.
0.7 (0.03) MIN.
6.2 (0.24) MIN.
36.5 (1.44)
Creepage distance: 36.33 (1.430) minimum
Strike distance: 17.43 (0.686) minimum
Quote between upper and lower pole pieces has to be considered after
application of mounting force (see thermal and mechanical specification)
20° ± 5°
C
A
Note:
A = Anode
C = Cathode
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 08-Feb-17 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Vishay:
ST730C12L0L ST730C12L1L ST730C14L0L ST730C14L1L ST730C16L0L ST730C16L1L ST730C18L1L VS-
ST730C12L0 VS-ST730C14L0 VS-ST730C16L0 VS-ST730C18L0 VS-ST730C12L1 VS-ST730C14L1 VS-
ST730C08L0 VS-ST730C18L1 VS-ST730C16L1 VS-ST730C08L1