ELECTRICAL SPECIFICATIONS: 1.0 INDUCTANCE: Pi-J1l=Pe-Je ; P4-J4=P5-J5 2.0 DC RESISTANCE: i) P4 Pe O@ @|@|@ @ : 65 uH O0.01V, 10 KHz, nominal. Pi-J1 ' 5 ohm MAX Pe-Je ' 5 ohm MAX P4-J4 ' 5 ohm MAX PS-JS ' 5 ohm MAX 3.0 Common Modcle: CMA (-dB> FREQUENCY <MHz> TYPICAL _MIN_ 1 8 5 5 17 15 20 23 15 70 25 20 200 22 17 500 ii 6 NOTES: PINS NOT ELECTRICALLY CONNECTED ARE OMITTED. InNet Technologies Inc. http://www.innettech.com Stewart Connector Systems http'//www.stewartconnector.com tor 3] "S1- 40017 REV. 0 3 *2.354 [59.79] MAX LED GREEN (4 PLCS) \ NOTES: TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS DIMENSIONS SHOWN WITH * TO BE CENTRAL ABOUT CENTER LINE LED YELLOW (4 PLCS) LED SPECIFICATION POWER DISSIPATION: 105mW FORWARD VOLTAGE *: YELLOW : 2.1V (TYP) ; 2.5V (MAX) GREEN : 2.25V (TYP) ;2.6V (MAX) INTENSITY @ 10ma : 2-8 MCD WAVELENGTH : YELLOW : 590 nm GREEN : 565 nm * WITHA FORWARD CURRENT OF 20mA 01720091 /CT720074 /24-0065 & > 425 I S 7 Me Gl (2) "+" ON DIMENSION INDICATES HIGHEST POINT OF BEAM 8. =. DIMENSIONS SHOWN ARE SUBJECT TO CHANGE WITHOUT NOTICE = #8 PIN NOT ELECTRICALLY CONNECTED MAYBE. OMITTED. 2 2S SEE ELECTRICAL DRAWING FOR OMITTED PINS. i fa AVAILABLE. WITH: 5 STANDARD 50 MICRO-INCH SELECTIVE = i ! TW tt | -.025 [0.63] BO TPS SURFACE) AK + 1-550 [13.97] TYP 275 [6.99]-} + | TOL NON-ACcUM _, _ 050 [1.27] YP TOL NON-ACCUM SIS i 550 [13.97] TYP =a [025 [0.63] S % 8 = % .035 [0.89] (32) = ;100 [2.54] TYP = eS &, oS - 2a 5, 128 [3.25] 7 8 e (2) 195 518)" \ ee SSS 1 PIN te Vipoos [18 1.68] TT 06 Yoo? > yo gr 2G YO % 46 me TT = \ go [1.02|(16) ss | *2.100 [53.34] =~ o *,309 [7. rosa S 2 [P= *.509 oome P.C.B. RECOMMENDED HOLE LAYOUT SEEN FROM COMPONENT SIDE TOLERANCE +.003 [0.08] UNLESS OTHERWISE SPECIFIED InNet Technologies Inc. http://www.innettech.com Stewart Connector Systems http://www.stewartconnector.com a) OF 3 DRAWING NO. S I _ A 0 0 | 7 REV. 0 3 POINT OF CONTACT i f WITH PANEL 1100 / > .080 = i Wa 1000 7 S 900 . = 800 = S / ss | 700 2 600 ly Oo S 500 ; 275 MAX a L Le S o V THE SUGGESTED PANEL OPENING IS INTENDED s 500 TO GIVE THE USER THE ABILITY TO HAVE 200 |p REASONABLE JACK / PANEL CLEARANCES 109 A YET MAINTAIN RELIABLE GROUNDING CAPABILITY. THESE VARIABLES CAN BE S So 8 + +t WH | | PANEL GROUNDING BEAM DEFLECTION S.0.S. = SUGGESTED OPENING SIZE = 2.562 S Kw _| SUGGESTED PANEL OPENING CT720035x1/24-001701 :010 MAX. RADIUS(4) L .000 (TOP OF PCB TO BOTTOM OF OPENING) ADJUSTED IN EITHER DIRECTION BUT MAY CARRY SOME CONSEQUENCES IN THE FORM OF LOWER MATING FORCES OR TIGHTER ASSEMBLY TOLERANCES. FORCE VALUES ON THE GRAPH ARE GENERAL AVERAGES TAKEN AT THE POINT OF CONTACT SHOWN ABOVE. THE SUGGESTED PANEL OPENING INCLUDES APPROXIMATELY .020 CLEARANCE ON THE SIDES AND TOP AND .005 ON THE BOTTOM. http://www.innettech.com http://www.stewartconnector.com InNet Technologies Inc. Stewart Connector Systems SHEET DRAWING NO. 3 OF 3 SI-4001 7 REV. 0 3