Freescale Semiconductor Technical Data Document Number: MPC8641DEC Rev. 0, 7/2008 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications 1 Overview The MPC8641 processor family integrates either one or two Power ArchitectureTM e600 processor cores with system logic required for networking, storage, wireless infrastructure, and general-purpose embedded applications. The MPC8641 integrates one e600 core while the MPC8641D integrates two cores. 1. 2. 3. 4. 5. 6. 7. 8. 9. This section provides a high-level overview of the MPC8641 and MPC8641D features. When referring to the MPC8641 throughout the document, the functionality described applies to both the MPC8641 and the MPC8641D. Any differences specific to the MPC8641D are noted. Figure 1 shows the major functional units within the MPC8641 and MPC8641D. The major difference between the MPC8641 and MPC8641D is that there are two cores on the MPC8641D. (c) Freescale Semiconductor, Inc., 2008. All rights reserved. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . .5 Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .13 Input Clocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 RESET Initialization . . . . . . . . . . . . . . . . . . . . . . . . . .18 DDR and DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . .19 DUART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Ethernet Management Interface Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Local Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 High-Speed Serial Interfaces (HSSI) . . . . . . . . . . . . . .60 PCI Express . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Serial RapidIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 Signal Listings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Clocking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 System Design Information . . . . . . . . . . . . . . . . . . . .122 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . .132 Document Revision History. . . . . . . . . . . . . . . . . . . .136 Overview e600 Core Block e600 Core Block e600 Core 32-Kbyte L1 Instruction Cache 1-Mbyte L2 Cache 32-Kbyte L1 Data Cache e600 Core 32-Kbyte L1 Instruction Cache 1-Mbyte L2 Cache 32-Kbyte L1 Data Cache MPX Bus MPX Coherency Module (MCM) Platform Bus SDRAM DDR SDRAM Controller SDRAM DDR SDRAM Controller ROM, GPIO Local Bus Controller (LBC) IRQs Multiprocessor Programmable Interrupt Controller (MPIC) Serial Dual Universal Asynchronous Receiver/Transmitter (DUART) I2C I2C Controller I2C I2C Controller RMII, GMII, MII, RGMII, TBI, RTBI RMII, GMII, MII, RGMII, TBI, RTBI Enhanced TSEC Controller [ x1/x2/x4/x8 PCI Exp (4 GB/s) AND 1x/4x SRIO (2.5 GB/s) ] OR [2-x1/x2/x4/x8 PCI Express (8 GB/S) ] Enhanced TSEC Controller PCI Express Interface Enhanced TSEC Controller 10/100/1Gb RMII, GMII, MII, RGMII, TBI, RTBI OCeaN Switch Fabric Serial RapidIO Interface or PCI Express Interface 10/100/1Gb 10/100/1Gb RMII, GMII, MII, RGMII, TBI, RTBI Platform Four-Channel DMA Controller External Control Enhanced TSEC Controller 10/100/1Gb Figure 1. MPC8641 and MPC8641D MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 2 Freescale Semiconductor Overview 1.1 Key Features The following lists an overview of the MPC8641 key feature set: * Major features of the e600 core are as follows: -- High-performance, 32-bit superscalar microprocessor that implements the PowerPC ISA -- Eleven independent execution units and three register files - Branch processing unit (BPU) - Four integer units (IUs) that share 32 GPRs for integer operands - 64-bit floating-point unit (FPU) - Four vector units and a 32-entry vector register file (VRs) - Three-stage load/store unit (LSU) -- Three issue queues, FIQ, VIQ, and GIQ, can accept as many as one, two, and three instructions, respectively, in a cycle. -- Rename buffers -- Dispatch unit -- Completion unit -- Two separate 32-Kbyte instruction and data level 1 (L1) caches -- Integrated 1-Mbyte, eight-way set-associative unified instruction and data level 2 (L2) cache with ECC -- 36-bit real addressing -- Separate memory management units (MMUs) for instructions and data -- Multiprocessing support features -- Power and thermal management -- Performance monitor -- In-system testability and debugging features -- Reliability and serviceability * MPX coherency module (MCM) -- Ten local address windows plus two default windows -- Optional low memory offset mode for core 1 to allow for address disambiguation * Address translation and mapping units (ATMUs) -- Eight local access windows define mapping within local 36-bit address space -- Inbound and outbound ATMUs map to larger external address spaces -- Three inbound windows plus a configuration window on PCI Express -- Four inbound windows plus a default window on serial RapidIO -- Four outbound windows plus default translation for PCI Express -- Eight outbound windows plus default translation for serial RapidIO with segmentation and sub-segmentation support MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 3 Overview * * * * DDR memory controllers -- Dual 64-bit memory controllers (72-bit with ECC) -- Support of up to a 300-MHz clock rate and a 600-MHz DDR2 SDRAM -- Support for DDR, DDR2 SDRAM -- Up to 16 Gbytes per memory controller -- Cache line and page interleaving between memory controllers. Serial RapidIO interface unit -- Supports RapidIO Interconnect Specification, Revision 1.2 -- Both 1x and 4x LP-Serial link interfaces -- Transmission rates of 1.25-, 2.5-, and 3.125-Gbaud (data rates of 1.0-, 2.0-, and 2.5-Gbps) per lane -- RapidIO-compliant message unit -- RapidIO atomic transactions to the memory controller PCI Express interface -- PCI Express 1.0a compatible -- Supports x1, x2, x4, and x8 link widths -- 2.5 Gbaud, 2.0 Gbps lane Four enhanced three-speed Ethernet controllers (eTSECs) -- Three-speed support (10/100/1000 Mbps) -- Four IEEE 802.3, 802.3u, 802.3x, 802.3z, 802.3ac, 802.3ab compliant controllers -- Support of the following physical interfaces: MII, RMII, GMII, RGMII, TBI, and RTBI -- -- -- -- -- -- -- * Support a full-duplex FIFO mode for high-efficiency ASIC connectivity TCP/IP off-load Header parsing Quality of service support VLAN insertion and deletion MAC address recognition Buffer descriptors are backward compatible with PowerQUICC II and PowerQUICC III programming models -- RMON statistics support -- MII management interface for control and status Programmable interrupt controller (PIC) -- Programming model is compliant with the OpenPIC architecture -- Supports 16 programmable interrupt and processor task priority levels -- Supports 12 discrete external interrupts and 48 internal interrupts -- Eight global high resolution timers/counters that can generate interrupts -- Allows processors to interrupt each other with 32b messages MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 4 Freescale Semiconductor Electrical Characteristics * * * * * * * * 2 -- Support for PCI-Express message-shared interrupts (MSIs) Local bus controller (LBC) -- Multiplexed 32-bit address and data operating at up to 133 MHz -- Eight chip selects support eight external slaves Integrated DMA controller -- Four-channel controller -- All channels accessible by both the local and the remote masters -- Supports transfers to or from any local memory or I/O port -- Ability to start and flow control each DMA channel from external 3-pin interface Device performance monitor -- Supports eight 32-bit counters that count the occurrence of selected events -- Ability to count up to 512 counter-specific events -- Supports 64 reference events that can be counted on any of the 8 counters -- Supports duration and quantity threshold counting -- Burstiness feature that permits counting of burst events with a programmable time between bursts -- Triggering and chaining capability -- Ability to generate an interrupt on overflow Dual I2C controllers -- Two-wire interface -- Multiple master support -- Master or slave I2C mode support -- On-chip digital filtering rejects spikes on the bus Boot sequencer -- Optionally loads configuration data from serial ROM at reset via the I2C interface -- Can be used to initialize configuration registers and/or memory -- Supports extended I2C addressing mode -- Data integrity checked with preamble signature and CRC DUART -- Two 4-wire interfaces (SIN, SOUT, RTS, CTS) -- Programming model compatible with the original 16450 UART and the PC16550D IEEE 1149.1-compliant, JTAG boundary scan Available as 1023 pin Hi-CTE flip chip ceramic ball grid array (FC-CBGA) Electrical Characteristics This section provides the AC and DC electrical specifications and thermal characteristics for the MPC8641. The MPC8641 is currently targeted to these specifications. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 5 Electrical Characteristics 2.1 Overall DC Electrical Characteristics This section covers the ratings, conditions, and other characteristics. 2.1.1 Absolute Maximum Ratings Table 1 provides the absolute maximum ratings. Table 1. Absolute Maximum Ratings1 Characteristic Symbol Absolute Maximum Value Unit Notes Cores supply voltages VDD_Core0, VDD_Core1 -0.3 to 1.21 V V Cores PLL supply AVDD_Core0, AVDD_Core1 -0.3 to 1.21 V V SVDD -0.3 to 1.21 V V SerDes Serial I/O Supply Port 1 XVDD_SRDS1 -0.3 to 1.21V V SerDes Serial I/O Supply Port 2 XVDD_SRDS2 -0.3 to 1.21 V V SerDes DLL and PLL supply voltage for Port 1 and Port 2 AV DD_SRDS1, AVDD_SRDS2 -0.3 to 1.21V V Platform Supply voltage VDD_PLAT -0.3 to 1.21V V Local Bus and Platform PLL supply voltage AVDD_LB, AVDD_PLAT -0.3 to 1.21V V D1_GVDD, D2_GVDD -0.3 to 2.75 V V 3 -0.3 to 1.98 V V 3 LVDD -0.3 to 3.63 V V 4 -0.3 to 2.75 V V 4 -0.3 to 3.63 V V 4 -0.3 to 2.75 V V 4 OVDD -0.3 to 3.63V V Dn_MVIN - 0.3 to (Dn_GVDD + 0.3) V Dn_MVREF - 0.3 to (Dn_GVDD/2 + 0.3) V Three-speed Ethernet signals LVIN TVIN GND to (LVDD+ 0.3) GND to (TVDD+ 0.3) V 5 DUART, Local Bus, DMA, Multiprocessor Interrupts, System Control & Clocking, Debug, Test, Power management, I2C, JTAG and Miscellaneous I/O voltage OV IN GND to (OVDD+ 0.3) V 5 SerDes Transceiver Supply (Ports 1 and 2) DDR and DDR2 SDRAM I/O supply voltages eTSEC 1 and 2 I/O supply voltage eTSEC 3 and 4 I/O supply voltage Local Bus, DUART, DMA, Multiprocessor Interrupts, System Control & Clocking, Debug, Test, Power management, I2C, JTAG and Miscellaneous I/O voltage Input voltage DDR and DDR2 SDRAM signals DDR and DDR2 SDRAM reference TVDD 2 5 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 6 Freescale Semiconductor Electrical Characteristics Table 1. Absolute Maximum Ratings1 (continued) Characteristic Storage temperature range Symbol Absolute Maximum Value TSTG -55 to 150 Unit Notes C Notes: 1. Functional and tested operating conditions are given in Table 2. Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stresses beyond those listed may affect device reliability or cause permanent damage to the device. 2. Core 1 characteristics apply only to MPC8641D. If two separate power supplies are used for VDD_Core0 and VDD_Core1, they must be kept within 100 mV of each other during normal run time. 3. The -0.3 to 2.75 V range is for DDR and -0.3 to 1.98 V range is for DDR2. 4. The 3.63V maximum is only supported when the port is configured in GMII, MII, RMII, or TBI modes; otherwise the 2.75V maximum applies. See Section 8.2, "FIFO, GMII, MII, TBI, RGMII, RMII, and RTBI AC Timing Specifications" for details on the recommended operating conditions per protocol. 5. During run time (M,L,T,O)VIN and Dn_MVREF may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 2. 2.1.2 Recommended Operating Conditions Table 2 provides the recommended operating conditions for the MPC8641. Note that the values in Table 2 are the recommended and tested operating conditions. Proper device operation outside of these conditions is not guaranteed. For details on order information and specific operating conditions for parts, see Section 21, "Ordering Information." Table 2. Recommended Operating Conditions Characteristic Cores supply voltages Cores PLL supply SerDes Transceiver Supply (Ports 1 and 2) Symbol VDD_Core0, VDD_Core1 AVDD_Core0, AV DD_Core1 SVDD Recommended Value Unit Notes 1.10 50 mV V 1, 2, 8 1.05 50 mV 1, 2, 7 0.95 50 mV 1, 2, 12 1.10 50 mV V 1.05 50 mV 7, 13 0.95 50 mV 12, 13 1.10 50 mV V 1.05 50 mV SerDes Serial I/O Supply Port 1 XVDD_SRDS1 1.10 50 mV XVDD_SRDS2 1.10 50 mV V Platform Supply voltage AVDD_SRDS1, AVDD_SRDS2 1.10 50 mV VDD_PLAT 1.10 50 mV V 8 7 V 1.05 50 mV 1.05 50 mV 8 7 1.05 50 mV SerDes DLL and PLL supply voltage for Port 1 and Port 2 8, 11 7, 11 1.05 50 mV SerDes Serial I/O Supply Port 2 8, 13 8 7 V 8 7 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 7 Electrical Characteristics Table 2. Recommended Operating Conditions (continued) Recommended Value Unit Notes AVDD_LB, AVDD_PLAT 1.10 50 mV V 8 D1_GV DD, D2_GVDD 2.5 V 125 mV V 9 1.8 V 90 mV V 9 LVDD 3.3 V 165 mV V 10 2.5 V 125 mV V 10 3.3 V 165 mV V 10 2.5 V 125 mV V 10 OV DD 3.3 V 165 mV V 5 Dn_MV IN GND to D n_GVDD V 3, 6 Dn_MV REF Dn_GVDD/2 1% V Three-speed Ethernet signals LVIN TVIN GND to LVDD GND to TVDD V 4, 6 DUART, Local Bus, DMA, Multiprocessor Interrupts, System Control & Clocking, Debug, Test, Power management, I2C, JTAG and Miscellaneous I/O voltage OVIN GND to OVDD V 5,6 TJ 0 to 105 C Characteristic Local Bus and Platform PLL supply voltage DDR and DDR2 SDRAM I/O supply voltages eTSEC 1 and 2 I/O supply voltage eTSEC 3 and 4 I/O supply voltage Local Bus, DUART, DMA, Multiprocessor Interrupts, System Control & Clocking, Debug, Test, Power management, I2C, JTAG and Miscellaneous I/O voltage Input voltage DDR and DDR2 SDRAM signals DDR and DDR2 SDRAM reference Junction temperature range Symbol TVDD 1.05 50 mV 7 Notes: 1. Core 1 characteristics apply only to MPC8641D 2. If two separate power supplies are used for VDD_Core0 and VDD_Core1, they must be at the same nominal voltage and the individual power supplies must be tracked and kept within 100 mV of each other during normal run time. 3. Caution: Dn_MVIN must meet the overshoot/undershoot requirements for Dn_GVDD as shown in Figure 2. 4. Caution: L/TVIN must meet the overshoot/undershoot requirements for L/TVDD as shown in Figure 2 during regular run time. 5. Caution: OVIN must meet the overshoot/undershoot requirements for OVDD as shown in Figure 2 during regular run time. 6. Timing limitations for M,L,T,O)VIN and Dn_MVREF during regular run time is provided in Figure 2 7. Applies to devices marked with a core frequency of 1333 MHz and below. Refer to Table 74 Part Numbering Nomenclature to determine if the device has been marked for a core frequency of 1333 MHz and below. 8. Applies to devices marked with a core frequency above 1333 MHz. Refer to Table 74 Part Numbering Nomenclature to determine if the device has been marked for a core frequency above 1333 MHz. 9. The 2.5 V 125 mV range is for DDR and 1.8 V 90 mV range is for DDR2. 10. See Section 8.2, "FIFO, GMII, MII, TBI, RGMII, RMII, and RTBI AC Timing Specifications" for details on the recommended operating conditions per protocol. 11. The PCI Express interface of the device is expected to receive signals from 0.175 to 1.2 V. For more information refer to Section 14.4.3, "Differential Receiver (RX) Input Specifications." 12. Applies to Part Number MC8641xxx1000NX only. VDD_Coren = 0.95 V and VDD_PLAT = 1.05 V devices. Refer to Table 74 Part Numbering Nomenclature to determine if the device has been marked for VDD_Coren = 0.95 V. 13. This voltage is the input to the filter discussed in Section 20.2, "Power Supply Design and Sequencing" and not necessarily the voltage at the AV DD_Coren pin, which may be reduced from VDD_Coren by the filter. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 8 Freescale Semiconductor Electrical Characteristics Figure 2 shows the undershoot and overshoot voltages at the interfaces of the MPC8641. L/T/D n_G/O/X/SVDD + 20% L/T/D n_G/O/X/SV DD + 5% VIH L/T/Dn_G/O/X/SVDD GND GND - 0.3 V VIL GND - 0.7 V Not to Exceed 10% of tCLK1 Note: 1. tCLK references clocks for various functional blocks as follows: DDR n = 10% of Dn_MCK period eTsecn = 10% of EC n_GTX_CLK125 period Local Bus = 10% of LCLK[0:2] period I2C = 10% of SYSCLK JTAG = 10% of SYSCLK Figure 2. Overshoot/Undershoot Voltage for D n_M/O/L/TVIN The MPC8641 core voltage must always be provided at nominal VDD_Coren (See Table 2 for actual recommended core voltage). Voltage to the processor interface I/Os are provided through separate sets of supply pins and must be provided at the voltages shown in Table 2. The input voltage threshold scales with respect to the associated I/O supply voltage. OVDD and L/TVDD based receivers are simple CMOS I/O circuits and satisfy appropriate LVCMOS type specifications. The DDR SDRAM interface uses a single-ended differential receiver referenced to each externally supplied Dn_MVREF signal (nominally set to Dn_GVDD/2) as is appropriate for the (SSTL-18 and SSTL-25) electrical signaling standards. 2.1.3 Output Driver Characteristics Table 3 provides information on the characteristics of the output driver strengths. The values are preliminary estimates. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 9 Electrical Characteristics Table 3. Output Drive Capability Driver Type Programmable Output Impedance () Supply Voltage Notes DDR1 signal 18 36 (half strength mode) Dn_GVDD = 2.5 V 4, 9 DDR2 signal 18 36 (half strength mode) Dn_GVDD = 1.8 V 1, 5, 9 Local Bus signals 45 25 OVDD = 3.3 V 2, 6 eTSEC/10/100 signals 45 T/LVDD = 3.3 V 6 30 T/LVDD = 2.5 V 6 DUART, DMA, Multiprocessor Interrupts, System Control & Clocking, Debug, Test, Power management, JTAG and Miscellaneous I/O voltage 45 OVDD = 3.3 V 6 I2C 150 OVDD = 3.3 V 7 SRIO, PCI Express 100 SVDD = 1.1/1.05 V 3, 8 Notes: 1. See the DDR Control Driver registers in the MPC8641D reference manual for more information. 2. Only the following local bus signals have programmable drive strengths: LALE, LAD[0:31], LDP[0:3], LA[27:31], LCKE, LCS[1:2], LWE[0:3], LGPL1, LGPL2, LGPL3, LGPL4, LGPL5, LCLK[0:2]. The other local bus signals have a fixed drive strength of 45 ohms. See the POR Impedance Control register in the MPC8641D reference manual for more information about local bus signals and their drive strength programmability. 3. See Section 17, "Signal Listings" for details on resistor requirements for the calibration of SDn_IMP_CAL_TX and SDn_IMP_CAL_RX transmit and receive signals. 4. Stub Series Terminated Logic (SSTL-25) type pins. 5. Stub Series Terminated Logic (SSTL-18) type pins. 6. Low Voltage Transistor-Transistor Logic (LVTTL) type pins. 7. Open Drain type pins. 8. Low Voltage Differential Signaling (LVDS) type pins. 9. The drive strength of the DDR interface in half strength mode is at Tj = 105C and at Dn_GV DD (min). MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 10 Freescale Semiconductor Electrical Characteristics 2.2 Power Up/Down Sequence The MPC8641 requires its power rails to be applied in a specific sequence in order to ensure proper device operation. NOTE The recommended maximum ramp up time for power supplies is 20 milliseconds. The chronological order of power up is: 1. All power rails other than DDR I/O (Dn_GVDD, and Dn_MVREF). NOTE There is no required order sequence between the individual rails for this item (# 1). However, VDD_PLAT, AVDD_PLAT rails must reach 90% of their recommended value before the rail for Dn_GVDD, and Dn_MVREF (in next step) reaches 10% of their recommended value. AVDD type supplies must be delayed with respect to their source supplies by the RC time constant of the PLL filter circuit described in Section 20.2.1, "PLL Power Supply Filtering". 2. Dn_GVDD, Dn_MVREF NOTE It is possible to leave the related power supply (Dn_GVDD, Dn_MVREF) turned off at reset for a DDR port that will not be used. Note that these power supplies can only be powered up again at reset for functionality to occur on the DDR port. 3. SYSCLK The recommended order of power down is as follows: 1. Dn_GVDD, Dn_MVREF 2. All power rails other than DDR I/O (Dn_GVDD, Dn_MVREF). NOTE SYSCLK may be powered down simultaneous to either of item # 1 or # 2 in the power down sequence. Beyond this, the power supplies may power down simultaneously if the preservation of DDRn memory is not a concern. See Figure 3 for more details on the Power and Reset Sequencing details MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 11 Electrical Characteristics Figure 3 illustrates the Power Up sequence as described above. 3.3 V L/T/OVDD DC Power Supply Voltage If 1 L/TVDD=2.5 V 2.5 V Dn_GVDD, = 1.8/2.5 V Dn_MVREF 1.8 V VDD_PLAT, AVDD_PLAT AVDD_LB, SVDD, XVDD_SRDSn AVDD_SRDSn VDD_Coren, AVDD_Coren 1.2 V 100 s Platform PLL Relock Time 3 7 0 Power Supply Ramp Up 2 Time SYSCLK 8 (not drawn to scale) 9 HRESET (& TRST) Asserted for 100 s after SYSCLK is functional 4 e6005 PLL Reset Configuration Pins Cycles Setup and hold Time 6 Notes: 1. Dotted waveforms correspond to optional supply values for a specified power supply. See Table 2. 2. The recommended maximum ramp up time for power supplies is 20 milliseconds. 3. Refer to Section 5, "RESET Initialization" for additional information on PLL relock and reset signal assertion timing requirements. 4. Refer to Table 11 for additional information on reset configuration pin setup timing requirements. In addition see Figure 68 regarding HRESET and JTAG connection details including TRST. 5. e600 PLL relock time is 100 microseconds maximum plus 255 MPX_clk cycles. 6. Stable PLL configuration signals are required as stable SYSCLK is applied. All other POR configuration inputs are required 4 SYSCLK cycles before HRESET negation and are valid at least 2 SYSCLK cycles after HRESET has negated (hold requirement). See Section 5, "RESET Initialization" for more information on setup and hold time of reset configuration signals. 7. VDD_PLAT, AVDD_PLAT must strictly reach 90% of their recommended voltage before the rail for Dn_GVDD, and Dn_MVREF reaches 10% of their recommended voltage. 8. SYSCLK must be driven only AFTER the power for the various power supplies is stable. 9. In device sleep mode, the reset configuration signals for DRAM types (TSEC2_TXD[4],TSEC2_TX_ER) must be valid BEFORE HRESET is asserted. Figure 3. MPC8641 Power-Up and Reset Sequence MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 12 Freescale Semiconductor Power Characteristics 3 Power Characteristics The power dissipation for the dual core MPC8641D device is shown in Table 4. Table 4. MPC8641D Power Dissipation (Dual Core) Power Mode Core Frequency (MHz) Platform Frequency (MHz) VDD_Coren, VDD_PLAT (Volts) Typical Thermal 1500 MHz 600 MHz 1.1 V Maximum 1333 MHz 533 MHz 1.05 V Maximum 1250 MHz 500 MHz 32.1 1, 2 43.4 1, 3 49.9 1, 4 23.9 1, 2 30.0 1, 3 34.1 1, 4 23.9 1, 2 30.0 1, 3 34.1 1, 4 23.9 1, 2 30.0 1, 3 34.1 1, 4 16.2 1, 2, 5 21.8 1, 3, 5 25.0 1, 4, 5 105 oC 105 oC 105 oC Typical 65 1000 MHz 400 MHz oC 1.05 V 105 oC Maximum 65 Typical Thermal 65 oC 1.05 V Maximum Thermal Notes 65 oC Typical Thermal Power (Watts) 65 oC Typical Thermal Junction Temperature 1000 MHz Maximum 500 MHz 0.95 V, 1.05 V oC 105 oC Notes: 1. These values specify the power consumption at nominal voltage and apply to all valid processor bus frequencies and configurations. The values do not include power dissipation for I/O supplies. 2. Typical power is an average value measured at the nominal recommended core voltage (VDD_Coren) and 65C junction temperature (see Table 2)while running the Dhrystone 2.1 benchmark and achieving 2.3 Dhrystone MIPs/MHz with one core at 100% efficiency and the second core at 65% efficiency. 3. Thermal power is the average power measured at nominal core voltage (VDD_Coren) and maximum operating junction temperature (see Table 2) while running the Dhrystone 2.1 benchmark and achieving 2.3 Dhrystone MIPs/MHz on both cores and a typical workload on platform interfaces. 4. Maximum power is the maximum power measured at nominal core voltage (VDD_Coren) and maximum operating junction temperature (see Table 2) while running a test which includes an entirely L1-cache-resident, contrived sequence of instructions which keep all the execution units maximally busy on both cores. 5. These power numbers are for Part Number MC8641Dxx1000NX only. VDD_Coren = 0.95 V and VDD_PLAT = 1.05 V. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 13 Power Characteristics The maximum power dissipation for individual power supplies of the MPC8641D is shown in Table 5. Table 5. MPC8641D Individual Supply Maximum Power Dissipation 1 Component Description Supply Voltage (Volts) Power (Watts) Per Core voltage Supply VDD_Core0/VDD_Core1 = 1.1 V @ 1500 MHz 21.00 Per Core PLL voltage supply AVDD_Core0/AVDD_Core1 = 1.1 V @ 1500 MHz 0.0125 Per Core voltage Supply VDD_Core0/VDD_Core1 = 1.05 V @ 1333 MHz 17.00 Per Core PLL voltage supply AV DD_Core0/AVDD_Core1 = 1.05 V @ 1333 MHz 0.0125 Per Core voltage Supply VDD_Core0/VDD_Core1 = 0.95 V @ 1000 MHz 11.50 5 Per Core PLL voltage supply AV DD_Core0/AVDD_Core1 = 0.95 V @ 1000 MHz 0.0125 5 DDR Controller I/O voltage supply Dn_GVDD = 2.5 V @ 400 MHz 0.80 2 Dn_GVDD = 1.8 V @ 533 MHz 0.68 2 Dn_GVDD = 1.8 V @ 600 MHz 0.77 2 16-bit FIFO @ 200 MHz eTsec 1&2/3&4 Voltage Supply L/TVDD = 3.3 V 0.11 2, 3 non-FIFO eTsecn Voltage Supply L/TVDD = 3.3 V 0.08 2 x8 SerDes transceiver Supply SVDD = 1.1 V 0.70 2 x8 SerDes I/O Supply XVDD_SRDS n = 1.1 V 0.66 2 SerDes PLL voltage supply Port 1 or 2 AVDD_SRDS1/AV DD_SRDS2 = 1.1 V 0.10 Platform I/O Supply OVDD = 3.3 V 0.45 Platform source Supply VDD_PLAT = 1.1 V @ 600 MHz 12.00 Platform source Supply VDD_PLAT = 1.05 Vn @ 500 MHz 9.80 Platform source Supply VDD_PLAT = 1.05 Vn @ 400 MHz 7.70 Platform, Local Bus PLL voltage Supply AVDD_PLAT, AVDD_LB = 1.1 V 0.0125 Notes 4 5 Notes: 1. This is a maximum power supply number which is provided for power supply and board design information. The numbers are based on 100% bus utilization for each component. The components listed are not expected to have 100% bus usage simultaneously for all components. Actual numbers may vary based on activity. 2. Number is based on a per port/interface value. 3. This is based on one eTSEC port used. Since 16-bit FIFO mode involves two ports, the number will need to be multiplied by two for the total. The other eTSEC protocols dissipate less than this number per port. Note that the power needs to be multiplied by the number of ports used for the protocol for the total eTSEC port power dissipation. 4.This includes Local Bus, DUART, I2C, DMA, Multiprocessor Interrupts, System Control & Clocking, Debug, Test, Power management, JTAG and Miscellaneous I/O voltage. 5. These power numbers are for Part Number MC8641xxx1000NX only. VDD_Coren = 0.95 V and VDD_PLAT = 1.05 V. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 14 Freescale Semiconductor Input Clocks The power dissipation for the MPC8641 single core device is shown in Table 6. Table 6. MPC8641 Power Dissipation (Single Core) Power Mode Core Frequency (MHz) Platform Frequency (MHz) VDD_Coren, VDD_PLAT (Volts) Typical Thermal 1500 MHz 600 MHz 1.1 V Maxim Junction Temperature Power (Watts) Notes 65 oC 20.3 1, 2 25.2 1, 3 28.9 1, 4 16.3 1, 2 20.2 1, 3 23.2 1, 4 16.3 1, 2 20.2 1, 3 23.2 1, 4 16.3 1, 2 20.2 1, 3 23.2 1, 4 11.6 1, 2, 5 14.4 1, 3, 5 16.5 1, 4, 5 105 oC o Typical 65 C Thermal 1333 MHz 533 MHz 1.05 V Maximum Typical 105 oC 65 Thermal 1250 MHz oC 1.05 V 500 MHz 105 oC Maximum 65 oC Typical Thermal 1000 MHz 400 MHz 1.05 V 105 oC Maximum 65 Typical Thermal 1000 MHz Maximum 500 MHz 0.95 V, 1.05 V oC 105 oC Notes: 1. These values specify the power consumption at nominal voltage and apply to all valid processor bus frequencies and configurations. The values do not include power dissipation for I/O supplies. 2. Typical power is an average value measured at the nominal recommended core voltage (VDD_Coren) and 65C junction temperature (see Table 2)while running the Dhrystone 2.1 benchmark and achieving 2.3 Dhrystone MIPs/MHz. 3. Thermal power is the average power measured at nominal core voltage (VDD_Coren) and maximum operating junction temperature (see Table 2) while running the Dhrystone 2.1 benchmark and achieving 2.3 Dhrystone MIPs/MHz and a typical workload on platform interfaces. 4. Maximum power is the maximum power measured at nominal core voltage (VDD_Coren) and maximum operating junction temperature (see Table 2) while running a test which includes an entirely L1-cache-resident, contrived sequence of instructions which keep all the execution units maximally busy. 5. These power numbers are for Part Number MC8641xx1000NX only. VDD_Coren = 0.95 V and VDD_PLAT = 1.05 V. 4 Input Clocks Table 7 provides the system clock (SYSCLK) DC specifications for the MPC8641. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 15 Input Clocks Table 7. SYSCLK DC Electrical Characteristics (OVDD = 3.3 V 165 mV.) Parameter Symbol Min Max Unit High-level input voltage VIH 2 OVDD + 0.3 V Low-level input voltage VIL -0.3 0.8 V Input current (VIN 1 = 0 V or VIN = V DD) IIN -- 5 A Note: 1. Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. 4.1 System Clock Timing Table 8 provides the system clock (SYSCLK) AC timing specifications for the MPC8641. Table 8. SYSCLK AC Timing Specifications At recommended operating conditions (see Table 2) with OVDD = 3.3 V 165 mV. Parameter/Condition Symbol Min Typical Max Unit Notes SYSCLK frequency fSYSCLK 66 -- 166.66 MHz 1 SYSCLK cycle time tSYSCLK 6 -- -- ns -- SYSCLK rise and fall time tKH, tKL 0.6 1.0 1.2 ns 2 tKHK/tSYSCLK 40 -- 60 % 3 -- -- -- 150 ps 4, 5 SYSCLK duty cycle SYSCLK jitter Notes: 1. Caution: The MPX clock to SYSCLK ratio and e600 core to MPX clock ratio settings must be chosen such that the resulting SYSCLK frequency, e600 (core) frequency, and MPX clock frequency do not exceed their respective maximum or minimum operating frequencies. Refer toSection 18.2, "MPX to SYSCLK PLL Ratio", and Section 18.3, "e600 to MPX clock PLL Ratio", for ratio settings. 2. Rise and fall times for SYSCLK are measured at 0.4 V and 2.7 V. 3. Timing is guaranteed by design and characterization. 4. This represents the short term jitter only and is guaranteed by design. 5. The SYSCLK driver's closed loop jitter bandwidth should be <500 kHz at -20 dB. The bandwidth must be set low to allow cascade-connected PLL-based devices to track SYSCLK drivers with the specified jitter. Note that the frequency modulation for SYSCLK reduces significantly for the spread spectrum source case. This is to guarantee what is supported based on design. 4.1.1 SYSCLK and Spread Spectrum Sources Spread spectrum clock sources are an increasingly popular way to control electromagnetic interference emissions (EMI) by spreading the emitted noise to a wider spectrum and reducing the peak noise magnitude in order to meet industry and government requirements. These clock sources intentionally add long-term jitter in order to diffuse the EMI spectral content. The jitter specification given in Table 8 considers short-term (cycle-to-cycle) jitter only and the clock generator's cycle-to-cycle output jitter should meet the MPC8641 input cycle-to-cycle jitter requirement. Frequency modulation and spread are separate concerns, and the MPC8641 is compatible with spread spectrum sources if the recommendations listed in Table 9 are observed. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 16 Freescale Semiconductor Input Clocks Table 9. Spread Spectrum Clock Source Recommendations At recommended operating conditions. See Table 2. Parameter Min Max Unit Notes Frequency modulation -- 50 kHz 1 Frequency spread -- 1.0 % 1, 2 Notes: 1. Guaranteed by design. 2. SYSCLK frequencies resulting from frequency spreading, and the resulting core and VCO frequencies, must meet the minimum and maximum specifications given in Table 8. It is imperative to note that the processor's minimum and maximum SYSCLK, core, and VCO frequencies must not be exceeded regardless of the type of clock source. Therefore, systems in which the processor is operated at its maximum rated e600 core frequency should avoid violating the stated limits by using down-spreading only. SDn_REF_CLK and SDn_REF_CLK was designed to work with a spread spectrum clock (+0 to 0.5% spreading at 30-33kHz rate is allowed), assuming both ends have same reference clock. For better results use a source without significant unintended modulation. 4.2 Real Time Clock Timing The RTC input is sampled by the platform clock (MPX clock). The output of the sampling latch is then used as an input to the counters of the PIC. There is no jitter specification. The minimum pulse width of the RTC signal should be greater than 2x the period of the MPX clock. That is, minimum clock high time is 2 x tMPX, and minimum clock low time is 2 x tMPX. There is no minimum RTC frequency; RTC may be grounded if not needed. 4.3 eTSEC Gigabit Reference Clock Timing Table 10 provides the eTSEC gigabit reference clocks (EC1_GTX_CLK125 and EC2_GTX_CLK125) AC timing specifications for the MPC8641. Table 10. EC n_GTX_CLK125 AC Timing Specifications Parameter/Condition Symbol Min Typical Max Unit Notes ECn_GTX_CLK125 frequency fG125 -- 125 100 ppm -- MHz 3 ECn_GTX_CLK125 cycle time tG125 -- 8 -- ns ECn_GTX_CLK125 peak-to-peak jitter tG125J -- -- 250 ps 1 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 17 RESET Initialization Table 10. ECn_GTX_CLK125 AC Timing Specifications (continued) ECn_GTX_CLK125 duty cycle % -- tG125H/tG125 1, 2 55 53 45 47 GMII, TBI 1000Base-T for RGMII, RTBI Notes: 1. Timing is guaranteed by design and characterization. 2. ECn_GTX_CLK125 is used to generate the GTX clock for the eTSEC transmitter with 2% degradation. ECn_GTX_CLK125 duty cycle can be loosened from 47/53% as long as the PHY device can tolerate the duty cycle generated by the eTSEC GTX_CLK. See Section 8.2.6, "RGMII and RTBI AC Timing Specifications" for duty cycle for 10Base-T and 100Base-T reference clock. 3. 100 ppm tolerance on ECn_GTX_CLK125 frequency NOTE The phase between the output clocks TSEC1_GTX_CLK and TSEC2_GTX_CLK (ports 1 and 2) is no more than 100 ps. The phase between the output clocks TSEC3_GTX_CLK and TSEC4_GTX_CLK (ports 3 and 4) is no more than 100 ps. 4.4 Other Input Clocks For information on the input clocks of other functional blocks of the platform such as SerDes, and eTSEC, see the specific section of this document. 5 RESET Initialization This section describes the AC electrical specifications for the RESET initialization timing requirements of the MPC8641. Table 11 provides the RESET initialization AC timing specifications. Table 11. RESET Initialization Timing Specifications Parameter/Condition Min Max Unit 100 -- s 3 -- SYSCLKs 1 100 -- s 2 Input setup time for POR configs (other than PLL config) with respect to negation of HRESET 4 -- SYSCLKs 1 Input hold time for all POR configs (including PLL config) with respect to negation of HRESET 2 -- SYSCLKs 1 Required assertion time of HRESET Minimum assertion time for SRESET_0 & SRESET_1 Platform PLL input setup time with stable SYSCLK before HRESET negation Notes MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 18 Freescale Semiconductor DDR and DDR2 SDRAM Table 11. RESET Initialization Timing Specifications Maximum valid-to-high impedance time for actively driven POR configs with respect to negation of HRESET -- 5 SYSCLKs 1 Notes: 1. SYSCLK is the primary clock input for the MPC8641. 2 This is related to HRESET assertion time. Stable PLL configuration inputs are required when a stable SYSCLK is applied. See the MPC8641D Integrated Host Processor Reference Manual for more details on the power-on reset sequence. Table 12 provides the PLL lock times. Table 12. PLL Lock Times Parameter/Condition Min Max Unit Notes (Platform and E600) PLL lock times -- 100 s 1 Local bus PLL -- 50 s Notes: 1. The PLL lock time for e600 PLLs require an additional 255 MPX_CLK cycles. 6 DDR and DDR2 SDRAM This section describes the DC and AC electrical specifications for the DDR SDRAM interface of the MPC8641. Note that DDR SDRAM is Dn_GVDD(typ) = 2.5 V and DDR2 SDRAM is Dn_GVDD(typ) = 1.8 V. 6.1 DDR SDRAM DC Electrical Characteristics Table 13 provides the recommended operating conditions for the DDR2 SDRAM component(s) of the MPC8641 when Dn_GVDD(typ) = 1.8 V. Table 13. DDR2 SDRAM DC Electrical Characteristics for Dn_GVDD(typ) = 1.8 V Parameter/Condition Symbol Min Max Unit Notes I/O supply voltage Dn_GVDD 1.71 1.89 V 1 I/O reference voltage Dn_MVREF 0.49 x Dn_GVDD 0.51 x Dn_GVDD V 2 I/O termination voltage VTT Dn_MVREF - 0.0 4 Dn_MVREF + 0.04 V 3 Input high voltage VIH Dn_MVREF+ 0.1 25 Dn_GVDD + 0.3 V Input low voltage VIL -0.3 Dn_MV REF - 0.125 V Output leakage current IOZ -50 50 A 4 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 19 DDR and DDR2 SDRAM Table 13. DDR2 SDRAM DC Electrical Characteristics for Dn_GVDD(typ) = 1.8 V Output high current (VOUT = 1.420 V) IOH -13.4 -- mA Output low current (VOUT = 0.280 V) IOL 13.4 -- mA Notes: 1. Dn_GV DD is expected to be within 50 mV of the DRAM Dn_GVDD at all times. 2. Dn_MV REF is expected to be equal to 0.5 x Dn_GVDD, and to track Dn_GVDD DC variations as measured at the receiver. Peak-to-peak noise on Dn_MVREF may not exceed 2% of the DC value. 3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be equal to Dn_MVREF. This rail should track variations in the DC level of Dn_MVREF. 4. Output leakage is measured with all outputs disabled, 0 V VOUT Dn_GVDD. Table 14 provides the DDR2 capacitance when Dn_GVDD(typ) = 1.8 V. Table 14. DDR2 SDRAM Capacitance for Dn_GVDD(typ)=1.8 V Parameter/Condition Symbol Min Max Unit Notes Input/output capacitance: DQ, DQS, DQS CIO 6 8 pF 1 Delta input/output capacitance: DQ, DQS, DQS CDIO -- 0.5 pF 1 Note: 1. This parameter is sampled. Dn_GVDD = 1.8 V 0.090 V, f = 1 MHz, TA = 25C, VOUT = Dn_GVDD/2, VOUT (peak-to-peak) = 0.2 V. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 20 Freescale Semiconductor DDR and DDR2 SDRAM Table 15 provides the recommended operating conditions for the DDR SDRAM component(s) when Dn_GVDD(typ) = 2.5 V. Table 15. DDR SDRAM DC Electrical Characteristics for Dn_GVDD (typ) = 2.5 V Parameter/Condition Symbol Min Max Unit Notes I/O supply voltage Dn_GVDD 2.375 2.625 V 1 I/O reference voltage Dn_MVREF 0.49 x Dn_GVDD 0.51 x Dn_GVDD V 2 I/O termination voltage VTT Dn_MVREF - 0.04 Dn_MV REF + 0.04 V 3 Input high voltage VIH Dn_MVREF + 0.15 D n_GVDD + 0.3 V Input low voltage VIL -0.3 Dn_MVREF- 0.15 V Output leakage current IOZ -50 50 A Output high current (VOUT = 1.95 V) IOH -16.2 -- mA Output low current (VOUT = 0.35 V) IOL 16.2 -- mA 4 Notes: 1. Dn_GV DD is expected to be within 50 mV of the DRAM Dn_GVDD at all times. 2. MVREF is expected to be equal to 0.5 x Dn_GVDD, and to track Dn_GV DD DC variations as measured at the receiver. Peak-to-peak noise on Dn_MVREF may not exceed 2% of the DC value. 3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be equal to Dn_MVREF. This rail should track variations in the DC level of Dn_MVREF. 4. Output leakage is measured with all outputs disabled, 0 V VOUT Dn_GV DD. Table 16 provides the DDR capacitance when Dn_GVDD (typ)=2.5 V. Table 16. DDR SDRAM Capacitance for Dn_GVDD (typ) = 2.5 V Parameter/Condition Symbol Min Max Unit Notes Input/output capacitance: DQ, DQS CIO 6 8 pF 1 Delta input/output capacitance: DQ, DQS CDIO -- 0.5 pF 1 Note: 1. This parameter is sampled. Dn_GVDD = 2.5 V 0.125 V, f = 1 MHz, TA = 25C, VOUT = Dn_GVDD/2, VOUT (peak-to-peak) = 0.2 V. Table 17 provides the current draw characteristics for MVREF. Table 17. Current Draw Characteristics for MVREF Parameter / Condition Current draw for MVREF Symbol Min Max Unit Note IMVREF -- 500 A 1 1. The voltage regulator for MVREF must be able to supply up to 500 A current. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 21 DDR and DDR2 SDRAM 6.2 DDR SDRAM AC Electrical Characteristics This section provides the AC electrical characteristics for the DDR SDRAM interface. 6.2.1 DDR SDRAM Input AC Timing Specifications Table 18 provides the input AC timing specifications for the DDR2 SDRAM when Dn_GVDD(typ)=1.8 V. Table 18. DDR2 SDRAM Input AC Timing Specifications for 1.8-V Interface At recommended operating conditions Parameter Symbol AC input low voltage Min Max -- Dn_MVREF - 0.25 Dn_MVREF - 0.20 Dn_MVREF + 0.25 Dn_MVREF + 0.20 -- Unit VIL 400, 533 MHz 600 MHz AC input high voltage V VIH 400, 533 MHz 600 MHz Notes V Table 19 provides the input AC timing specifications for the DDR SDRAM when Dn_GVDD(typ)=2.5 V. Table 19. DDR SDRAM Input AC Timing Specifications for 2.5-V Interface At recommended operating conditions. Parameter Symbol Min Max Unit AC input low voltage VIL -- Dn_MVREF - 0.31 V AC input high voltage VIH Dn_MVREF + 0.31 -- V Notes Table 20 provides the input AC timing specifications for the DDR SDRAM interface. Table 20. DDR SDRAM Input AC Timing Specifications At recommended operating conditions. Parameter Symbol Controller Skew for MDQS--MDQ/MECC Min Max tCISKEW Unit Notes ps 1, 2 600 MHz -240 240 3 533 MHz -300 300 3 400 MHz -365 365 Note: 1. tCISKEW represents the total amount of skew consumed by the controller between MDQS[n] and any corresponding bit that will be captured with MDQS[n]. This should be subtracted from the total timing budget. 2. The amount of skew that can be tolerated from MDQS to a corresponding MDQ signal is called tDISKEW.This can be determined by the following equation: tDISKEW =+/-(T/4 - abs(tCISKEW)) where T is the clock period and abs(tCISKEW) is the absolute value of tCISKEW. 3. Maximum DDR1 frequency is 400 MHz. Figure 4 shows the DDR SDRAM input timing for the MDQS to MDQ skew measurement (tDISKEW). MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 22 Freescale Semiconductor DDR and DDR2 SDRAM MCK[n] MCK[n] tMCK MDQS[n] MDQ[x] D0 D1 tDISKEW tDISKEW Figure 4. DDR Input Timing Diagram for tDISKEW MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 23 DDR and DDR2 SDRAM 6.2.2 DDR SDRAM Output AC Timing Specifications Table 21. DDR SDRAM Output AC Timing Specifications At recommended operating conditions. Parameter MCK[n] cycle time, MCK[n]/MCK[n] crossing MCK duty cycle Symbol 1 Min Max Unit Notes tMCK 3 10 ns 2 47.5 47 47 52.5 53 53 ADDR/CMD output setup with respect to MCK 8 9 9 tDDKHAS ns 3 600 MHz 1.10 -- 7 533 MHz 1.48 -- 7 400 MHz 1.95 -- ADDR/CMD output hold with respect to MCK tDDKHAX ns 3 600 MHz 1.10 -- 7 533 MHz 1.48 -- 7 400 MHz 1.95 -- MCS[n] output setup with respect to MCK tDDKHCS ns 3 600 MHz 1.10 -- 7 533 MHz 1.48 -- 7 400 MHz 1.95 -- MCS[n] output hold with respect to MCK tDDKHCX ns 3 600 MHz 1.10 -- 7 533 MHz 1.48 -- 7 400 MHz 1.95 -- -0.6 0.6 MCK to MDQS Skew tDDKHMH MDQ/MECC/MDM output setup with respect to MDQS tDDKHDS, tDDKLDS ns 4 ps 5 600 MHz 500 -- 7 533 MHz 590 -- 7 400 MHz 700 -- MDQ/MECC/MDM output hold with respect to MDQS MDQS preamble start % tMCKH/tMCK 600 MHz 533 MHz 400 MHz tDDKHDX, tDDKLDX ps 5 600 MHz 500 -- 7 533 MHz 590 -- 7 400 MHz 700 -- -0.5 x tMCK - 0.6 -0.5 x tMCK +0.6 tDDKHMP ns 6 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 24 Freescale Semiconductor DDR and DDR2 SDRAM Table 21. DDR SDRAM Output AC Timing Specifications (continued) At recommended operating conditions. Parameter MDQS epilogue end Symbol 1 Min Max Unit Notes tDDKHME -0.6 0.6 ns 6 Note: 1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing (DD) from the rising or falling edge of the reference clock (KH or KL) until the output went invalid (AX or DX). For example, tDDKHAS symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs (A) are setup (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes low (L) until data outputs (D) are invalid (X) or data output hold time. 2. All MCK/MCK referenced measurements are made from the crossing of the two signals 0.1 V. 3. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ/MECC/MDM/MDQS. 4. Note that tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD) from the rising edge of the MCK[n] clock (KH) until the MDQS signal is valid (MH). tDDKHMH can be modified through control of the DQS override bits (called WR_DATA_DELAY) in the TIMING_CFG_2 register. This will typically be set to the same delay as the clock adjust in the CLK_CNTL register. The timing parameters listed in the table assume that these 2 parameters have been set to the same adjustment value. See the MPC8641 Integrated Processor Reference Manual for a description and understanding of the timing modifications enabled by use of these bits. 5. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), ECC (MECC), or data mask (MDM). The data strobe should be centered inside of the data eye at the pins of the microprocessor. 6. All outputs are referenced to the rising edge of MCK[n] at the pins of the microprocessor. Note that tDDKHMP follows the symbol conventions described in note 1. 7. Maximum DDR1 frequency is 400 MHz 8. Per the JEDEC spec the DDR2 duty cycle at 600 MHz is the average low and high cycle time values that are defined as the average pulse widths calculated across any consecutive 200 pulses. Jitter can sometimes force single low and high cycle times to drift from the average values. tJIT = 125 ps. 9. Per the JEDEC spec the DDR2 duty cycle at 400 and 533 MHz is the low and high cycle time values. NOTE For the ADDR/CMD setup and hold specifications in Table 21, it is assumed that the Clock Control register is set to adjust the memory clocks by 1/2 applied cycle. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 25 DDR and DDR2 SDRAM Figure 5 shows the DDR SDRAM output timing for the MCK to MDQS skew measurement (tDDKHMH). MCK[n] MCK[n] tMCK tDDKHMHmax) = 0.6 ns MDQS tDDKHMH(min) = -0.6 ns MDQS Figure 5. Timing Diagram for tDDKHMH Figure 6 shows the DDR SDRAM output timing diagram. MCK[n] MCK[n] tMCK tDDKHAS ,tDDKHCS tDDKHAX ,tDDKHCX ADDR/CMD Write A0 NOOP tDDKHMP tDDKHMH MDQS[n] tDDKHME tDDKHDS tDDKLDS MDQ[x] D0 D1 tDDKLDX tDDKHDX Figure 6. DDR SDRAM Output Timing Diagram MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 26 Freescale Semiconductor DUART Figure 7 provides the AC test load for the DDR bus. Z0 = 50 Output Dn_GVDD/2 RL = 50 Figure 7. DDR AC Test Load 7 DUART This section describes the DC and AC electrical specifications for the DUART interface of the MPC8641. 7.1 DUART DC Electrical Characteristics Table 22 provides the DC electrical characteristics for the DUART interface. Table 22. DUART DC Electrical Characteristics Parameter Symbol Min Max Unit High-level input voltage VIH 2 OVDD + 0.3 V Low-level input voltage VIL - 0.3 0.8 V Input current (VIN 1 = 0 V or VIN = VDD) IIN -- 5 A High-level output voltage (OVDD = min, IOH = -100 A) VOH OVDD - 0.2 -- V Low-level output voltage (OVDD = min, IOL = 100 A) VOL -- 0.2 V Note: 1. Note that the symbol V IN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. 7.2 DUART AC Electrical Specifications Table 23 provides the AC timing parameters for the DUART interface. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 27 Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management Table 23. DUART AC Timing Specifications Parameter Value Unit Notes Minimum baud rate MPX clock/1,048,576 baud 1,2 Maximum baud rate MPX clock/16 baud 1,3 16 -- 1,4 Oversample rate Notes: 1. Guaranteed by design. 2. MPX clock refers to the platform clock. 3. Actual attainable baud rate will be limited by the latency of interrupt processing. 4. The middle of a start bit is detected as the 8th sampled 0 after the 1-to-0 transition of the start bit. Subsequent bit values are sampled each 16th sample. 8 Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management This section provides the AC and DC electrical characteristics for enhanced three-speed and MII management. 8.1 Enhanced Three-Speed Ethernet Controller (eTSEC) (10/100/1Gb Mbps)--GMII/MII/TBI/RGMII/RTBI/RMII Electrical Characteristics The electrical characteristics specified here apply to all gigabit media independent interface (GMII), media independent interface (MII), ten-bit interface (TBI), reduced gigabit media independent interface (RGMII), reduced ten-bit interface (RTBI), and reduced media independent interface (RMII) signals except management data input/output (MDIO) and management data clock (MDC). The RGMII and RTBI interfaces are defined for 2.5 V, while the GMII and TBI interfaces can be operated at 3.3 or 2.5 V. Whether the GMII or TBI interface is operated at 3.3 or 2.5 V, the timing is compliant with the IEEE 802.3 standard. The RGMII and RTBI interfaces follow the Reduced Gigabit Media-Independent Interface (RGMII) Specification Version 1.3 (12/10/2000). The RMII interface follows the RMII Consortium RMII Specification Version 1.2 (3/20/1998). The electrical characteristics for MDIO and MDC are specified in Section 9, "Ethernet Management Interface Electrical Characteristics." 8.1.1 eTSEC DC Electrical Characteristics All GMII, MII, TBI, RGMII, RMII and RTBI drivers and receivers comply with the DC parametric attributes specified in Table 24 and Table 25. The potential applied to the input of a GMII, MII, TBI, RGMII, RMII or RTBI receiver may exceed the potential of the receiver's power supply (i.e., a GMII driver powered from a 3.6-V supply driving VOH into a GMII receiver powered from a 2.5-V supply). Tolerance for dissimilar GMII driver and receiver supply potentials is implicit in these specifications. The MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 28 Freescale Semiconductor Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management RGMII and RTBI signals are based on a 2.5-V CMOS interface voltage as defined by JEDEC EIA/JESD8-5. Table 24. GMII, MII, RMII, TBI and FIFO DC Electrical Characteristics Parameter Symbol Min Max Unit LVDD TVDD 3.135 3.465 V Output high voltage (LV DD/TVDD = Min, IOH = -4.0 mA) VOH 2.40 -- V Output low voltage (LV DD/TVDD = Min, IOL = 4.0 mA) VOL -- 0.50 V Input high voltage VIH 2.0 -- V Input low voltage VIL -- 0.90 V Input high current (VIN = LVDD, VIN = TVDD) IIH -- 40 A Input low current (VIN = GND) IIL -600 Supply voltage 3.3 V Notes 1, 2 1, 2, 3 A -- 3 Notes: 1 LVDD supports eTSECs 1 and 2. TVDD supports eTSECs 3 and 4. 3 The symbol V , in this case, represents the LV and TV symbols referenced in Table 1 and Table 2. IN IN IN 2 Table 25. GMII, RGMII, RTBI, TBI and FIFO DC Electrical Characteristics Parameters Symbol Min Max Unit LVDD/TVDD 2.375 2.625 V Output high voltage (LVDD/TVDD = Min, IOH = -1.0 mA) VOH 2.00 -- V Output low voltage (LVDD/TVDD = Min, IOL = 1.0 mA) VOL -- 0.40 V Input high voltage VIH 1.70 -- V Input low voltage VIL -- 0.90 V Input high current (VIN = LVDD, VIN = TVDD) IIH -- 10 A Input low current (VIN = GND) IIL -15 Supply voltage 2.5 V Notes 1, 2 1, 2, 3 -- A 3 Note: 1 2 LVDD supports eTSECs 1 and 2. TVDD supports eTSECs 3 and 4. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 29 Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management 3 Note that the symbol VIN, in this case, represents the LVIN and TVIN symbols referenced in Table 1 and Table 2. 8.2 FIFO, GMII, MII, TBI, RGMII, RMII, and RTBI AC Timing Specifications The AC timing specifications for FIFO, GMII, MII, TBI, RGMII, RMII and RTBI are presented in this section. 8.2.1 FIFO AC Specifications The basis for the AC specifications for the eTSEC's FIFO modes is the double data rate RGMII and RTBI specifications, since they have similar performance and are described in a source-synchronous fashion like FIFO modes. However, the FIFO interface provides deliberate skew between the transmitted data and source clock in GMII fashion. When the eTSEC is configured for FIFO modes, all clocks are supplied from external sources to the relevant eTSEC interface. That is, the transmit clock must be applied to the eTSECn's TSECn_TX_CLK, while the receive clock must be applied to pin TSECn_RX_CLK. The eTSEC internally uses the transmit clock to synchronously generate transmit data and outputs an echoed copy of the transmit clock back out onto the TSECn_GTX_CLK pin (while transmit data appears on TSECn_TXD[7:0], for example). It is intended that external receivers capture eTSEC transmit data using the clock on TSECn_GTX_CLK as a source- synchronous timing reference. Typically, the clock edge that launched the data can be used, since the clock is delayed by the eTSEC to allow acceptable set-up margin at the receiver. Note that there is relationship between the maximum FIFO speed and the platform speed. For more information see Section 18.4.2, "Platform to FIFO Restrictions" NOTE The phase between the output clocks TSEC1_GTX_CLK and TSEC2_GTX_CLK (ports 1 and 2) is no more than 100 ps. The phase between the output clocks TSEC3_GTX_CLK and TSEC4_GTX_CLK (ports 3 and 4) is no more than 100 ps. A summary of the FIFO AC specifications appears in Table 26 and Table 27. Table 26. FIFO Mode Transmit AC Timing Specification At recommended operating conditions with L/TVDD of 3.3 V 5% and 2.5 V 5%. Parameter/Condition Symbol Min Typ Max Unit TX_CLK, GTX_CLK clock period (GMII mode) tFIT 7.0 8.0 100 ns TX_CLK, GTX_CLK clock period (Encoded mode) tFIT 5.3 8.0 100 ns tFITH/tFIT 45 50 55 % TX_CLK, GTX_CLK peak-to-peak jitter tFITJ -- -- 250 ps Rise time TX_CLK (20%-80%) tFITR -- -- 0.75 ns Fall time TX_CLK (80%-20%) tFITF -- -- 0.75 ns TX_CLK, GTX_CLK duty cycle MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 30 Freescale Semiconductor Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management Table 26. FIFO Mode Transmit AC Timing Specification (continued) At recommended operating conditions with L/TVDD of 3.3 V 5% and 2.5 V 5%. Parameter/Condition Symbol Min Typ Max Unit FIFO data TXD[7:0], TX_ER, TX_EN setup time to GTX_CLK tFITDV 2.0 -- -- ns GTX_CLK to FIFO data TXD[7:0], TX_ER, TX_EN hold time tFITDX 0.5 -- 3.0 ns Table 27. FIFO Mode Receive AC Timing Specification At recommended operating conditions with L/TVDD of 3.3 V 5% and 2.5 V 5%. Parameter/Condition Symbol Min Typ Max Unit tFIR 1 7.0 8.0 100 ns 1 5.3 8.0 100 ns tFIRH/tFIR 45 50 55 % RX_CLK peak-to-peak jitter tFIRJ -- -- 250 ps Rise time RX_CLK (20%-80%) tFIRR -- -- 0.75 ns Fall time RX_CLK (80%-20%) tFIRF -- -- 0.75 ns RXD[7:0], RX_DV, RX_ER setup time to RX_CLK tFIRDV 1.5 -- -- ns RXD[7:0], RX_DV, RX_ER hold time to RX_CLK tFIRDX 0.5 -- -- ns RX_CLK clock period (GMII mode) RX_CLK clock period (Encoded mode) tFIR RX_CLK duty cycle 1 100 ppm tolerance on RX_CLK frequency Timing diagrams for FIFO appear in Figure 8 and Figure 9. . tFITF tFITR tFIT GTX_CLK tFITH tFITDV tFITDX TXD[7:0] TX_EN TX_ER Figure 8. FIFO Transmit AC Timing Diagram MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 31 Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management tFIRR tFIR RX_CLK tFIRH tFIRF RXD[7:0] RX_DV RX_ER valid data tFIRDV tFIRDX Figure 9. FIFO Receive AC Timing Diagram 8.2.2 GMII AC Timing Specifications This section describes the GMII transmit and receive AC timing specifications. 8.2.2.1 GMII Transmit AC Timing Specifications Table 28 provides the GMII transmit AC timing specifications. Table 28. GMII Transmit AC Timing Specifications At recommended operating conditions with L/TVDD of 3.3 V 5% and 2.5 V 5%. Symbol 1 Min Typ Max Unit GMII data TXD[7:0], TX_ER, TX_EN setup time tGTKHDV 2.5 -- -- ns GTX_CLK to GMII data TXD[7:0], TX_ER, TX_EN delay tGTKHDX 0.5 -- 5.0 ns GTX_CLK data clock rise time (20%-80%) tGTXR2 -- -- 1.0 ns GTX_CLK data clock fall time (80%-20%) tGTXF2 -- -- 1.0 ns Parameter/Condition Notes: 1. The symbols used for timing specifications herein follow the pattern t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tGTKHDV symbolizes GMII transmit timing (GT) with respect to the tGTX clock reference (K) going to the high state (H) relative to the time date input signals (D) reaching the valid state (V) to state or setup time. Also, tGTKHDX symbolizes GMII transmit timing (GT) with respect to the tGTX clock reference (K) going to the high state (H) relative to the time date input signals (D) going invalid (X) or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tGTX represents the GMII(G) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. Guaranteed by design. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 32 Freescale Semiconductor Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management Figure 10 shows the GMII transmit AC timing diagram. tGTXR tGTX GTX_CLK tGTXF tGTXH TXD[7:0] TX_EN TX_ER tGTKHDX tGTKHDV Figure 10. GMII Transmit AC Timing Diagram 8.2.2.2 GMII Receive AC Timing Specifications Table 29 provides the GMII receive AC timing specifications. Table 29. GMII Receive AC Timing Specifications At recommended operating conditions with L/TVDD of 3.3 V 5% and 2.5 V 5%. Symbol 1 Min Typ Max Unit tGRX3 -- 8.0 -- ns tGRXH/tGRX 40 -- 60 ns RXD[7:0], RX_DV, RX_ER setup time to RX_CLK tGRDVKH 2.0 -- -- ns RXD[7:0], RX_DV, RX_ER hold time to RX_CLK tGRDXKH Parameter/Condition RX_CLK clock period RX_CLK duty cycle 0.5 -- -- ns RX_CLK clock rise time (20%-80%) tGRXR 2 -- -- 1.0 ns RX_CLK clock fall time (80%-20%) tGRXF2 -- -- 1.0 ns Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tGRDVKH symbolizes GMII receive timing (GR) with respect to the time data input signals (D) reaching the valid state (V) relative to the tRX clock reference (K) going to the high state (H) or setup time. Also, tGRDXKL symbolizes GMII receive timing (GR) with respect to the time data input signals (D) went invalid (X) relative to the tGRX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tGRX represents the GMII (G) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. Guaranteed by design. 3. 100 ppm tolerance on RX_CLK frequency Figure 11 provides the AC test load for eTSEC. Output Z0 = 50 RL = 50 LVDD/2 Figure 11. eTSEC AC Test Load MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 33 Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management Figure 12 shows the GMII receive AC timing diagram. tGRX tGRXR RX_CLK tGRXH tGRXF RXD[7:0] RX_DV RX_ER tGRDXKH tGRDVKH Figure 12. GMII Receive AC Timing Diagram 8.2.3 MII AC Timing Specifications This section describes the MII transmit and receive AC timing specifications. 8.2.3.1 MII Transmit AC Timing Specifications Table 30 provides the MII transmit AC timing specifications. Table 30. MII Transmit AC Timing Specifications At recommended operating conditions with L/TVDD of 3.3 V 5%. Symbol 1 Min Typ Max Unit TX_CLK clock period 10 Mbps tMTX2 -- 400 -- ns TX_CLK clock period 100 Mbps tMTX -- 40 -- ns tMTXH/tMTX 35 -- 65 % tMTKHDX 1 5 15 ns TX_CLK data clock rise time (20%-80%) tMTXR2 1.0 -- 4.0 ns TX_CLK data clock fall time (80%-20%) tMTXF2 1.0 -- 4.0 ns Parameter/Condition TX_CLK duty cycle TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII transmit timing (MT) for the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. For example, the subscript of tMTX represents the MII(M) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. Guaranteed by design. Figure 13 shows the MII transmit AC timing diagram. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 34 Freescale Semiconductor Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management tMTX tMTXR TX_CLK tMTXF tMTXH TXD[3:0] TX_EN TX_ER tMTKHDX Figure 13. MII Transmit AC Timing Diagram 8.2.3.2 MII Receive AC Timing Specifications Table 31 provides the MII receive AC timing specifications. Table 31. MII Receive AC Timing Specifications At recommended operating conditions with L/TVDD of 3.3 V 5%. Symbol 1 Min Typ Max Unit RX_CLK clock period 10 Mbps tMRX2,3 -- 400 -- ns RX_CLK clock period 100 Mbps tMRX3 -- 40 -- ns tMRXH/tMRX 35 -- 65 % RXD[3:0], RX_DV, RX_ER setup time to RX_CLK tMRDVKH 10.0 -- -- ns RXD[3:0], RX_DV, RX_ER hold time to RX_CLK tMRDXKH 10.0 -- -- ns RX_CLK clock rise time (20%-80%) tMRXR2 1.0 -- 4.0 ns RX_CLK clock fall time (80%-20%) tMRXF2 1.0 -- 4.0 ns Parameter/Condition RX_CLK duty cycle Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive timing (MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K) going to the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data input signals (D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tMRX represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. Guaranteed by design. 3. 100 ppm tolerance on RX_CLK frequency Figure 14 provides the AC test load for eTSEC. Output Z0 = 50 RL = 50 LVDD/2 Figure 14. eTSEC AC Test Load MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 35 Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management Figure 15 shows the MII receive AC timing diagram. tMRX tMRXR RX_CLK tMRXF tMRXH RXD[3:0] RX_DV RX_ER Valid Data tMRDVKH tMRDXKL Figure 15. MII Receive AC Timing Diagram 8.2.4 TBI AC Timing Specifications This section describes the TBI transmit and receive AC timing specifications. 8.2.4.1 TBI Transmit AC Timing Specifications Table 32 provides the TBI transmit AC timing specifications. Table 32. TBI Transmit AC Timing Specifications At recommended operating conditions with L/TVDD of 3.3 V 5% and 2.5 V 5%. Symbol 1 Min Typ Max Unit TCG[9:0] setup time GTX_CLK going high tTTKHDV 2.0 -- -- ns TCG[9:0] hold time from GTX_CLK going high tTTKHDX 1.0 -- -- ns GTX_CLK rise time (20%-80%) tTTXR2 -- -- 1.0 ns GTX_CLK fall time (80%-20%) tTTXF2 -- -- 1.0 ns Parameter/Condition Notes: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state )(reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tTTKHDV symbolizes the TBI transmit timing (TT) with respect to the time from tTTX (K) going high (H) until the referenced data signals (D) reach the valid state (V) or setup time. Also, tTTKHDX symbolizes the TBI transmit timing (TT) with respect to the time from tTTX (K) going high (H) until the referenced data signals (D) reach the invalid state (X) or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tTTX represents the TBI (T) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. Guaranteed by design. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 36 Freescale Semiconductor Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management Figure 16 shows the TBI transmit AC timing diagram. tTTXR tTTX GTX_CLK tTTXH tTTXF tTTXF TCG[9:0] tTTKHDV tTTXR tTTKHDX Figure 16. TBI Transmit AC Timing Diagram 8.2.4.2 TBI Receive AC Timing Specifications Table 33 provides the TBI receive AC timing specifications. Table 33. TBI Receive AC Timing Specifications At recommended operating conditions with L/TVDD of 3.3 V 5% and 2.5 V 5%. Parameter/Condition PMA_RX_CLK[0:1] clock period PMA_RX_CLK[0:1] skew Symbol 1 Min tTRX3 Typ Max 16.0 Unit ns tSKTRX 7.5 -- 8.5 ns tTRXH/tTRX 40 -- 60 % RCG[9:0] setup time to rising PMA_RX_CLK tTRDVKH 2.5 -- -- ns RCG[9:0] hold time to rising PMA_RX_CLK tTRDXKH 1.5 -- -- ns PMA_RX_CLK[0:1] clock rise time (20%-80%) tTRXR2 0.7 -- 2.4 ns PMA_RX_CLK[0:1] clock fall time (80%-20%) tTRXF2 0.7 -- 2.4 ns PMA_RX_CLK[0:1] duty cycle Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tTRDVKH symbolizes TBI receive timing (TR) with respect to the time data input signals (D) reach the valid state (V) relative to the tTRX clock reference (K) going to the high (H) state or setup time. Also, tTRDXKH symbolizes TBI receive timing (TR) with respect to the time data input signals (D) went invalid (X) relative to the tTRX clock reference (K) going to the high (H) state. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tTRX represents the TBI (T) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). For symbols representing skews, the subscript is skew (SK) followed by the clock that is being skewed (TRX). 2. Guaranteed by design. 3. 100 ppm tolerance on PMA_RX_CLK[0:1] frequency MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 37 Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management Figure 17 shows the TBI receive AC timing diagram. tTRX tTRXR PMA_RX_CLK1 tTRXH tTRXF Valid Data RCG[9:0] Valid Data tTRDVKH tSKTRX tTRDXKH PMA_RX_CLK0 tTRXH tTRDXKH tTRDVKH Figure 17. TBI Receive AC Timing Diagram 8.2.5 TBI Single-Clock Mode AC Specifications When the eTSEC is configured for TBI modes, all clocks are supplied from external sources to the relevant eTSEC interface. In single-clock TBI mode, when TBICON[CLKSEL] = 1 a 125-MHz TBI receive clock is supplied on TSECn_RX_CLK pin (no receive clock is used on TSECn_TX_CLK in this mode, whereas for the dual-clock mode this is the PMA1 receive clock). The 125-MHz transmit clock is applied on the TSEC_GTX_CLK125 pin in all TBI modes. A summary of the single-clock TBI mode AC specifications for receive appears in Table 34. Table 34. TBI single-clock Mode Receive AC Timing Specification At recommended operating conditions with L/TVDD of 3.3 V 5% and 2.5 V 5%. Parameter/Condition Min Typ Max Unit 7.5 8.0 8.5 ns tTRRH/tTRR 40 50 60 % RX_CLK peak-to-peak jitter tTRRJ -- -- 250 ps Rise time RX_CLK (20%-80%) tTRRR -- -- 1.0 ns Fall time RX_CLK (80%-20%) tTRRF -- -- 1.0 ns RCG[9:0] setup time to RX_CLK rising edge tTRRDVKH 2.0 -- -- ns RCG[9:0] hold time to RX_CLK rising edge tTRRDXKH 1.0 -- -- ns RX_CLK clock period RX_CLK duty cycle 1 Symbol tTRR 1 100 ppm tolerance on RX_CLK frequency MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 38 Freescale Semiconductor Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management A timing diagram for TBI receive appears in Figure 18. . tTRRR tTRR RX_CLK tTRRH tTRRF RCG[9:0] valid data tTRRDVKH tTRRDXKH Figure 18. TBI Single-Clock Mode Receive AC Timing Diagram 8.2.6 RGMII and RTBI AC Timing Specifications Table 35 presents the RGMII and RTBI AC timing specifications. Table 35. RGMII and RTBI AC Timing Specifications At recommended operating conditions with L/TVDD of 2.5 V 5%. Parameter/Condition Data to clock output skew (at transmitter) Data to clock input skew (at receiver) 2 Clock period duration 3 Duty cycle for 10BASE-T and 100BASE-TX Rise time (20%-80%) Fall time (80%-20%) 3, 4 Symbol 1 Min Typ Max Unit tSKRGT5 -500 0 500 ps tSKRGT 1.0 -- 2.8 ns tRGT5,6 7.2 8.0 8.8 ns tRGTH/tRGT5 40 50 60 % tRGTR5 -- -- 0.75 ns 5 -- -- 0.75 ns tRGTF Notes: 1. Note that, in general, the clock reference symbol representation for this section is based on the symbols RGT to represent RGMII and RTBI timing. For example, the subscript of tRGT represents the TBI (T) receive (RX) clock. Note also that the notation for rise (R) and fall (F) times follows the clock symbol that is being represented. For symbols representing skews, the subscript is skew (SK) followed by the clock that is being skewed (RGT). 2. This implies that PC board design will require clocks to be routed such that an additional trace delay of greater than 1.5 ns will be added to the associated clock signal. 3. For 10 and 100 Mbps, tRGT scales to 400 ns 40 ns and 40 ns 4 ns, respectively. 4. Duty cycle may be stretched/shrunk during speed changes or while transitioning to a received packet's clock domains as long as the minimum duty cycle is not violated and stretching occurs for no more than three tRGT of the lowest speed transitioned between. 5. Guaranteed by characterization 6. 100 ppm tolerance on RX_CLK frequency MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 39 Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management Figure 19 shows the RGMII and RTBI AC timing and multiplexing diagrams. tRGT tRGTH GTX_CLK (At Transmitter) tSKRGT TXD[8:5][3:0] TXD[7:4][3:0] TXD[8:5] TXD[3:0] TXD[7:4] TXD[4] TXEN TX_CTL TXD[9] TXERR tSKRGT TX_CLK (At PHY) RXD[8:5][3:0] RXD[7:4][3:0] RXD[8:5] RXD[3:0] RXD[7:4] tSKRGT RXD[4] RXDV RX_CTL RXD[9] RXERR tSKRGT RX_CLK (At PHY) Figure 19. RGMII and RTBI AC Timing and Multiplexing Diagrams 8.2.7 RMII AC Timing Specifications This section describes the RMII transmit and receive AC timing specifications. 8.2.7.1 RMII Transmit AC Timing Specifications The RMII transmit AC timing specifications are in Table 36. Table 36. RMII Transmit AC Timing Specifications At recommended operating conditions with L/TVDD of 3.3 V 5%. Parameter/Condition REF_CLK clock period Symbol 1 Min tRMT Typ Max 20.0 Unit ns tRMTH/tRMT 35 50 65 % REF_CLK peak-to-peak jitter tRMTJ -- -- 250 ps Rise time REF_CLK (20%-80%) tRMTR 1.0 -- 2.0 ns Fall time REF_CLK (80%-20%) tRMTF 1.0 -- 2.0 ns REF_CLK duty cycle MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 40 Freescale Semiconductor Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management Table 36. RMII Transmit AC Timing Specifications (continued) At recommended operating conditions with L/TVDD of 3.3 V 5%. Parameter/Condition REF_CLK to RMII data TXD[1:0], TX_EN delay Symbol 1 Min Typ Max Unit tRMTDX 1.0 -- 10.0 ns Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII transmit timing (MT) for the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. For example, the subscript of tMTX represents the MII(M) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). Figure 20 shows the RMII transmit AC timing diagram. tRMT tRMTR REF_CLK tRMTH tRMTF TXD[1:0] TX_EN TX_ER tRMTDX Figure 20. RMII Transmit AC Timing Diagram 8.2.7.2 RMII Receive AC Timing Specifications Table 37. RMII Receive AC Timing Specifications At recommended operating conditions with L/TVDD of 3.3 V 5%. Symbol 1 Min Typ Max Unit tRMR 15.0 20.0 25.0 ns tRMRH/tRMR 35 50 65 % REF_CLK peak-to-peak jitter tRMRJ -- -- 250 ps Rise time REF_CLK (20%-80%) tRMRR 1.0 -- 2.0 ns Fall time REF_CLK (80%-20%) tRMRF 1.0 -- 2.0 ns RXD[1:0], CRS_DV, RX_ER setup time to REF_CLK rising edge tRMRDV 4.0 -- -- ns Parameter/Condition REF_CLK clock period REF_CLK duty cycle MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 41 Ethernet Management Interface Electrical Characteristics Table 37. RMII Receive AC Timing Specifications (continued) At recommended operating conditions with L/TVDD of 3.3 V 5%. Parameter/Condition RXD[1:0], CRS_DV, RX_ER hold time to REF_CLK rising edge Symbol 1 Min Typ Max Unit tRMRDX 2.0 -- -- ns Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive timing (MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K) going to the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data input signals (D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tMRX represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). Figure 21 provides the AC test load for eTSEC. Z0 = 50 Output RL = 50 LVDD/2 Figure 21. eTSEC AC Test Load Figure 22 shows the RMII receive AC timing diagram. tRMRR tRMR REF_CLK tRMRH RXD[1:0] CRS_DV RX_ER tRMRF Valid Data tRMRDV tRMRDX Figure 22. RMII Receive AC Timing Diagram 9 Ethernet Management Interface Electrical Characteristics The electrical characteristics specified here apply to MII management interface signals MDIO (management data input/output) and MDC (management data clock). The electrical characteristics for GMII, RGMII, RMII, TBI and RTBI are specified in "Section 8, "Ethernet: Enhanced Three-Speed Ethernet (eTSEC), MII Management." MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 42 Freescale Semiconductor Ethernet Management Interface Electrical Characteristics 9.1 MII Management DC Electrical Characteristics The MDC and MDIO are defined to operate at a supply voltage of 3.3 V. The DC electrical characteristics for MDIO and MDC are provided in Table 38. Table 38. MII Management DC Electrical Characteristics Parameter Symbol Min Max Unit OVDD 3.135 3.465 V Output high voltage (OVDD = Min, IOH = -1.0 mA) VOH 2.10 -- V Output low voltage (OVDD =Min, IOL = 1.0 mA) VOL -- 0.50 V Input high voltage VIH 1.70 -- V Input low voltage VIL -- 0.90 V Input high current (OVDD = Max, VIN 1 = 2.1 V) IIH -- 40 A Input low current (OVDD = Max, VIN = 0.5 V) IIL -600 -- A Supply voltage (3.3 V) Note: 1. Note that the symbol V IN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. 9.2 MII Management AC Electrical Specifications Table 39 provides the MII management AC timing specifications. Table 39. MII Management AC Timing Specifications At recommended operating conditions with OVDD is 3.3 V 5%. Symbol 1 Min Typ Max Unit Notes MDC frequency fMDC 2.5 -- 9.3 MHz 2, 4 MDC period tMDC 80 -- 400 ns MDC clock pulse width high tMDCH 32 -- -- ns MDC to MDIO valid tMDKHDV 16*tMPXCLK MDC to MDIO delay tMDKHDX 10 -- MDIO to MDC setup time tMDDVKH 5 MDIO to MDC hold time tMDDXKH tMDCR Parameter/Condition MDC rise time ns 5 16*tMPXCLK ns 3, 5 -- -- ns 0 -- -- ns -- -- 10 ns 4 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 43 Ethernet Management Interface Electrical Characteristics Table 39. MII Management AC Timing Specifications (continued) At recommended operating conditions with OVDD is 3.3 V 5%. Parameter/Condition MDC fall time Symbol 1 Min Typ Max Unit Notes tMDHF -- -- 10 ns 4 Notes: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMDKHDX symbolizes management data timing (MD) for the time tMDC from clock reference (K) high (H) until data outputs (D) are invalid (X) or data hold time. Also, tMDDVKH symbolizes management data timing (MD) with respect to the time data input signals (D) reach the valid state (V) relative to the tMDC clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. This parameter is dependent on the system clock speed. (The maximum frequency is the maximum platform frequency divided by 64.) 3. This parameter is dependent on the system clock speed. (That is, for a system clock of 267 MHz, the maximum frequency is 8.3 MHz and the minimum frequency is 1.2 MHz; for a system clock of 375 MHz, the maximum frequency is 11.7 MHz and the minimum frequency is 1.7 MHz.) 4. Guaranteed by design. 5. tMPXCLK is the platform (MPX) clock Figure 23 provides the AC test load for eTSEC. Z0 = 50 Output RL = 50 OVDD/2 Figure 23. eTSEC AC Test Load NOTE Output will see a 50 load since what it sees is the transmission line. Figure 24 shows the MII management AC timing diagram. tMDC tMDCR MDC tMDCF tMDCH MDIO (Input) tMDDVKH tMDDXKH MDIO (Output) tMDKHDX Figure 24. MII Management Interface Timing Diagram MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 44 Freescale Semiconductor Local Bus 10 Local Bus This section describes the DC and AC electrical specifications for the local bus interface of the MPC8641. 10.1 Local Bus DC Electrical Characteristics Table 40 provides the DC electrical characteristics for the local bus interface operating at OVDD = 3.3 V DC. Table 40. Local Bus DC Electrical Characteristics (3.3 V DC) Parameter Symbol Min Max Unit High-level input voltage VIH 2 OVDD + 0.3 V Low-level input voltage VIL -0.3 0.8 V Input current (VIN 1 = 0 V or VIN = OVDD) IIN -- 5 A High-level output voltage (OVDD = min, IOH = -2 mA) VOH OVDD - 0.2 -- V Low-level output voltage (OVDD = min, IOL = 2 mA) VOL -- 0.2 V Note: 1. Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. 10.2 Local Bus AC Electrical Specifications Table 41 describes the timing parameters of the local bus interface at OVDD = 3.3 V with PLL enabled. For information about the frequency range of local bus see Section 18.1, "Clock Ranges." Table 41. Local Bus Timing Parameters (OVDD = 3.3 V)m - PLL Enabled Symbol 1 Min Max Unit Notes Local bus cycle time tLBK 7.5 -- ns 2 Local Bus Duty Cycle tLBKH/tLBK 45 55 % LCLK[n] skew to LCLK[m] or LSYNC_OUT tLBKSKEW -- 150 ps 7, 8 Input setup to local bus clock (except LGTA/LUPWAIT) tLBIVKH1 1.8 -- ns 3, 4 LGTA/LUPWAIT input setup to local bus clock tLBIVKH2 1.7 -- ns 3, 4 Input hold from local bus clock (except LGTA/LUPWAIT) tLBIXKH1 1.0 -- ns 3, 4 LGTA/LUPWAIT input hold from local bus clock tLBIXKH2 1.0 -- ns 3, 4 LALE output transition to LAD/LDP output transition (LATCH hold time) tLBOTOT 1.5 -- ns 6 Parameter MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 45 Local Bus Table 41. Local Bus Timing Parameters (OVDD = 3.3 V)m - PLL Enabled (continued) Parameter Symbol 1 Min Max Unit Local bus clock to output valid (except LAD/LDP and LALE) tLBKHOV1 -- 2.0 ns Local bus clock to data valid for LAD/LDP tLBKHOV2 -- 2.2 ns Local bus clock to address valid for LAD tLBKHOV3 -- 2.3 ns Local bus clock to LALE assertion tLBKHOV4 -- 2.3 ns Output hold from local bus clock (except LAD/LDP and LALE) tLBKHOX1 0.7 -- ns Output hold from local bus clock for LAD/LDP tLBKHOX2 0.7 -- ns 3 Local bus clock to output high Impedance (except LAD/LDP and LALE) tLBKHOZ1 -- 2.5 ns 5 Local bus clock to output high impedance for LAD/LDP tLBKHOZ2 -- 2.5 ns 5 Notes 3 Note: 1. The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold time. 2. All timings are in reference to LSYNC_IN for PLL enabled and internal local bus clock for PLL bypass mode. 3. All signals are measured from OVDD/2 of the rising edge of LSYNC_IN for PLL enabled or internal local bus clock for PLL bypass mode to 0.4 x OVDD of the signal in question for 3.3-V signaling levels. 4. Input timings are measured at the pin. 5. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 6. tLBOTOT is a measurement of the minimum time between the negation of LALE and any change in LAD. tLBOTOT is programmed with the LBCR[AHD] parameter. 7. Maximum possible clock skew between a clock LCLK[m] and a relative clock LCLK[n]. Skew measured between complementary signals at BVDD/2. 8. Guaranteed by design. Figure 25 provides the AC test load for the local bus. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 46 Freescale Semiconductor Local Bus Z0 = 50 Output OVDD/2 RL = 50 Figure 25. Local Bus AC Test Load Figure 26 to Figure 31 show the local bus signals. LSYNC_IN tLBIXKH1 tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBIXKH2 tLBIVKH2 Input Signal: LGTA LUPWAIT Output Signals: LA[27:31]/LBCTL/LBCKE/LOE/ LSDA10/LSDWE/LSDRAS/ LSDCAS/LSDDQM[0:3] tLBKHOV1 tLBKHOZ1 tLBKHOX1 tLBKHOV2 tLBKHOZ2 tLBKHOX2 Output (Data) Signals: LAD[0:31]/LDP[0:3] tLBKHOV3 tLBKHOZ2 tLBKHOX2 Output (Address) Signal: LAD[0:31] tLBOTOT tLBKHOV4 LALE Figure 26. Local Bus Signals (PLL Enabled) NOTE PLL bypass mode is recommended when LBIU frequency is at or below 83 MHz. When LBIU operates above 83 Mhz, LBIU PLL is recommended to be enabled. Table 42 describes the general timing parameters of the local bus interface at OVDD = 3.3 V with PLL bypassed. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 47 Local Bus Table 42. Local Bus Timing Parameters--PLL Bypassed Symbol 1 Min Max Unit Notes Local bus cycle time tLBK 12 -- ns 2 Local bus duty cycle tLBKH/tLBK 45 55 % Internal launch/capture clock to LCLK delay tLBKHKT 2.3 3.9 ns 8 Input setup to local bus clock (except LGTA/LUPWAIT) tLBIVKH1 5.7 -- ns 4, 5 LGTA/LUPWAIT input setup to local bus clock tLBIVKL2 5.6 -- ns 4, 5 Input hold from local bus clock (except LGTA/LUPWAIT) tLBIXKH1 -1.8 -- ns 4, 5 LGTA/LUPWAIT input hold from local bus clock tLBIXKL2 -1.3 -- ns 4, 5 LALE output transition to LAD/LDP output transition (LATCH hold time) tLBOTOT 1.5 -- ns 6 Local bus clock to output valid (except LAD/LDP and LALE) tLBKLOV1 -- -0.3 ns Local bus clock to data valid for LAD/LDP tLBKLOV2 -- -0.1 ns 4 Local bus clock to address valid for LAD tLBKLOV3 -- 0 ns 4 Local bus clock to LALE assertion tLBKLOV4 -- 0 ns 4 Output hold from local bus clock (except LAD/LDP and LALE) tLBKLOX1 -3.2 -- ns 4 Output hold from local bus clock for LAD/LDP tLBKLOX2 -3.2 -- ns 4 Local bus clock to output high Impedance (except LAD/LDP and LALE) tLBKLOZ1 -- 0.2 ns 7 Parameter MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 48 Freescale Semiconductor Local Bus Table 42. Local Bus Timing Parameters--PLL Bypassed (continued) Parameter Symbol 1 Min Max Unit Notes Local bus clock to output high impedance for LAD/LDP tLBKLOZ2 -- 0.2 ns 7 Notes: 1. The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold time. 2. All timings are in reference to local bus clock for PLL bypass mode. Timings may be negative with respect to the local bus clock because the actual launch and capture of signals is done with the internal launch/capture clock, which precedes LCLK by tLBKHKT. 3. Maximum possible clock skew between a clock LCLK[m] and a relative clock LCLK[n]. Skew measured between complementary signals at BVDD/2. 4. All signals are measured from BVDD/2 of the rising edge of local bus clock for PLL bypass mode to 0.4 x BVDD of the signal in question for 3.3-V signaling levels. 5. Input timings are measured at the pin. 6. The value of tLBOTOT is the measurement of the minimum time between the negation of LALE and any change in LAD 7. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 8. Guaranteed by characterization. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 49 Local Bus Internal launch/capture clock tLBKHKT LCLK[n] tLBIVKH1 tLBIXKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBIVKL2 Input Signal: LGTA tLBIXKL2 LUPWAIT tLBKLOV1 tLBKLOX1 Output Signals: LA[27:31]/LBCTL/LBCKE/LOE/ LSDA10/LSDWE/LSDRAS/ LSDCAS/LSDDQM[0:3] tLBKLOZ1 tLBKLOZ2 tLBKLOV2 Output (Data) Signals: LAD[0:31]/LDP[0:3] tLBKLOX2 tLBKLOV3 Output (Address) Signal: LAD[0:31] tLBKLOV4 tLBOTOT LALE Figure 27. Local Bus Signals (PLL Bypass Mode) NOTE In PLL bypass mode, LCLK[n] is the inverted version of the internal clock with the delay of tLBKHKT. In this mode, signals are launched at the rising edge of the internal clock and are captured at falling edge of the internal clock, with the exception of the LGTA/LUPWAIT signal, which is captured at the rising edge of the internal clock. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 50 Freescale Semiconductor Local Bus LSYNC_IN T1 T3 GPCM Mode Output Signals: LCS[0:7]/LWE tLBKHOV1 tLBKHOZ1 GPCM Mode Input Signal: LGTA tLBIVKH2 tLBIXKH2 UPM Mode Input Signal: LUPWAIT tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBIXKH1 tLBKHOV1 tLBKHOZ1 UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] Figure 28. Local Bus Signals, GPCM/UPM Signals for LCRR[CLKDIV] = 2 (clock ratio of 4) (PLL Enabled) MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 51 Local Bus Internal launch/capture clock T1 T3 LCLK tLBKLOX1 tLBKLOV1 GPCM Mode Output Signals: LCS[0:7]/LWE tLBKLOZ1 GPCM Mode Input Signal: LGTA tLBIVKL2 tLBIXKL2 UPM Mode Input Signal: LUPWAIT tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBIXKH1 UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] Figure 29. Local Bus Signals, GPCM/UPM Signals for LCRR[CLKDIV] = 2 (clock ratio of 4) (PLL Bypass Mode) MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 52 Freescale Semiconductor Local Bus LSYNC_IN T1 T2 T3 T4 tLBKHOV1 tLBKHOZ1 GPCM Mode Output Signals: LCS[0:7]/LWE GPCM Mode Input Signal: LGTA tLBIVKH2 tLBIXKH2 UPM Mode Input Signal: LUPWAIT tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBIXKH1 tLBKHOV1 tLBKHOZ1 UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] Figure 30. Local Bus Signals, GPCM/UPM Signals for LCRR[CLKDIV] = 4 or 8 (clock ratio of 8 or 16) (PLL Enabled) MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 53 JTAG Internal launch/capture clock T1 T2 T3 T4 LCLK tLBKLOX1 tLBKLOV1 GPCM Mode Output Signals: LCS[0:7]/LWE tLBKLOZ1 GPCM Mode Input Signal: LGTA tLBIVKL2 tLBIXKL2 UPM Mode Input Signal: LUPWAIT tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBIXKH1 UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] Figure 31. Local Bus Signals, GPCM/UPM Signals for LCRR[CLKDIV] = 4 or 8 (clock ratio of 8 or 16) (PLL Bypass Mode) 11 JTAG This section describes the DC and AC electrical specifications for the IEEE 1149.1 (JTAG) interface of the MPC8641/D. 11.1 JTAG DC Electrical Characteristics Table 43 provides the DC electrical characteristics for the JTAG interface. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 54 Freescale Semiconductor JTAG Table 43. JTAG DC Electrical Characteristics Parameter Symbol Min Max Unit High-level input voltage VIH 2 OVDD + 0.3 V Low-level input voltage VIL - 0.3 0.8 V Input current (VIN 1 = 0 V or VIN = VDD) IIN -- 5 A High-level output voltage (OVDD = min, IOH = -100 A) VOH OVDD - 0.2 -- V Low-level output voltage (OVDD = min, IOL = 100 A) VOL -- 0.2 V Note: 1. Note that the symbol V IN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. 11.2 JTAG AC Electrical Specifications Table 44 provides the JTAG AC timing specifications as defined in Figure 33 through Figure 35. Table 44. JTAG AC Timing Specifications (Independent of SYSCLK) 1 At recommended operating conditions (see Table 3). Symbol 2 Min Max Unit JTAG external clock frequency of operation fJTG 0 33.3 MHz JTAG external clock cycle time t JTG 30 -- ns tJTKHKL 15 -- ns tJTGR & tJTGF 0 2 ns 6 tTRST 25 -- ns 3 Boundary-scan data TMS, TDI tJTDVKH tJTIVKH 4 0 -- -- Boundary-scan data TMS, TDI tJTDXKH tJTIXKH 20 25 -- -- Boundary-scan data TDO tJTKLDV tJTKLOV 4 4 20 25 Boundary-scan data TDO tJTKLDX tJTKLOX 30 30 -- -- JTAG external clock to output high impedance: Boundary-scan data TDO tJTKLDZ tJTKLOZ 3 3 19 9 Parameter JTAG external clock pulse width measured at 1.4 V JTAG external clock rise and fall times TRST assert time Notes ns Input setup times: Input hold times: 4 ns Valid times: 4 ns Output hold times: 5 ns 5, 6 ns 5, 6 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 55 JTAG Table 44. JTAG AC Timing Specifications (Independent of SYSCLK) 1 (continued) At recommended operating conditions (see Table 3). Parameter Symbol 2 Min Max Unit Notes Notes: 1. All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50- load (see Figure 32). Time-of-flight delays must be added for trace lengths, vias, and connectors in the system. 2. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device timing (JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K) going to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals (D) went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 3. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only. 4. Non-JTAG signal input timing with respect to tTCLK. 5. Non-JTAG signal output timing with respect to tTCLK. 6. Guaranteed by design. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 56 Freescale Semiconductor JTAG Figure 32 provides the AC test load for TDO and the boundary-scan outputs. Z0 = 50 Output R L = 50 OVDD/2 Figure 32. AC Test Load for the JTAG Interface Figure 33 provides the JTAG clock input timing diagram. JTAG External Clock VM VM VM tJTGR tJTKHKL tJTGF tJTG VM = Midpoint Voltage (OVDD/2) Figure 33. JTAG Clock Input Timing Diagram Figure 34 provides the TRST timing diagram. TRST VM VM tTRST VM = Midpoint Voltage (OVDD /2) Figure 34. TRST Timing Diagram Figure 35 provides the boundary-scan timing diagram. JTAG External Clock VM VM tJTDVKH tJTDXKH Boundary Data Inputs Input Data Valid tJTKLDV tJTKLDX Boundary Data Outputs Output Data Valid tJTKLDZ Boundary Data Outputs Output Data Valid VM = Midpoint Voltage (OV DD/2) Figure 35. Boundary-Scan Timing Diagram MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 57 I2C 12 I2C This section describes the DC and AC electrical characteristics for the I2C interfaces of the MPC8641. 12.1 I2C DC Electrical Characteristics Table 45 provides the DC electrical characteristics for the I2C interfaces. Table 45. I2C DC Electrical Characteristics At recommended operating conditions with OVDD of 3.3 V 5%. Parameter Symbol Min Max Unit Input high voltage level VIH 0.7 x OV DD OVDD + 0.3 V Input low voltage level VIL -0.3 0.3 x OV DD V Low level output voltage VOL 0 0.2 x OV DD V 1 tI2KHKL 0 50 ns 2 Input current each I/O pin (input voltage is between 0.1 x OVDD and 0.9 x OVDD(max) II -10 10 A 3 Capacitance for each I/O pin CI -- 10 pF Pulse width of spikes which must be suppressed by the input filter Notes Notes: 1. Output voltage (open drain or open collector) condition = 3 mA sink current. 2. Refer to the MPC8641 Integrated Host Processor Reference Manual for information on the digital filter used. 3. I/O pins will obstruct the SDA and SCL lines if OVDD is switched off. 12.2 I2C AC Electrical Specifications Table 46 provides the AC timing parameters for the I2C interfaces. Table 46. I2C AC Electrical Specifications All values refer to VIH (min) and VIL (max) levels (see Table 45). Symbol 1 Min Max Unit fI2C 0 400 kHz Low period of the SCL clock tI2CL 4 1.3 -- s High period of the SCL clock tI2CH 4 0.6 -- s Setup time for a repeated START condition tI2SVKH 4 0.6 -- s Hold time (repeated) START condition (after this period, the first clock pulse is generated) tI2SXKL 4 0.6 -- s Data setup time tI2DVKH 4 100 -- ns -- 02 -- -- s 20 + 0.1 C B5 300 ns Parameter SCL clock frequency Data input hold time: tI2DXKL CBUS compatible masters I2C bus devices Rise time of both SDA and SCL signals tI2CR MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 58 Freescale Semiconductor I2C Table 46. I2C AC Electrical Specifications (continued) All values refer to VIH (min) and VIL (max) levels (see Table 45). Parameter Symbol 1 Min Max Unit tI2CF 20 + 0.1 Cb 5 300 ns Fall time of both SDA and SCL signals 3 s Data output delay time tI2OVKL -- 0.9 Set-up time for STOP condition tI2PVKH 0.6 -- s Bus free time between a STOP and START condition tI2KHDX 1.3 -- s Noise margin at the LOW level for each connected device (including hysteresis) VNL 0.1 x OV DD -- V Noise margin at the HIGH level for each connected device (including hysteresis) VNH 0.2 x OV DD -- V Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I2C timing (I2) with respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. Also, tI2SXKL symbolizes I2C timing (I2) for the time that the data with respect to the start condition (S) went invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH symbolizes I2C timing (I2) for the time that the data with respect to the stop condition (P) reaching the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. As a transmitter, the MPC8641 provides a delay time of at least 300 ns for the SDA signal (referred to the Vihmin of the SCL signal) to bridge the undefined region of the falling edge of SCL to avoid unintended generation of Start or Stop condition. When MPC8641 acts as the I2C bus master while transmitting, MPC8641 drives both SCL and SDA. As long as the load on SCL and SDA are balanced, MPC8641 would not cause unintended generation of Start or Stop condition. Therefore, the 300 ns SDA output delay time is not a concern. If, under some rare condition, the 300 ns SDA output delay time is required for MPC8641 as transmitter, the following setting is recommended for the FDR bit field of the I2CFDR register to ensure both the desired I2C SCL clock frequency and SDA output delay time are achieved, assuming that the desired I2C SCL clock frequency is 400 KHz and the Digital Filter Sampling Rate Register (I2CDFSRR) is programmed with its default setting of 0x10 (decimal 16): I2C Source Clock Frequency 333 MHz 266 MHz 200 MHz 133 MHz FDR Bit Setting 0x2A 0x05 0x26 0x00 Actual FDR Divider Selected 896 704 512 384 378 KHz 390 KHz 346 KHz Actual I2C SCL Frequency Generated 371 KHz For the detail of I2C frequency calculation, refer to the application note AN2919 "Determining the I2C Frequency Divider Ratio for SCL". Note that the I2C Source Clock Frequency is half of the MPX clock frequency for MPC8641. 3. The maximum tI2DXKL has only to be met if the device does not stretch the LOW period (tI2CL) of the SCL signal. 4. Guaranteed by design. 5. CB = capacitance of one bus line in pF. Figure 32 provides the AC test load for the I2C. Output Z0 = 50 RL = 50 OVDD/2 Figure 36. I2C AC Test Load Figure 37 shows the AC timing diagram for the I2C bus. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 59 High-Speed Serial Interfaces (HSSI) SDA tI2CF tI2DVKH tI2CL tI2KHKL tI2SXKL tI2CF tI2CR SCL tI2SXKL S tI2CH tI2DXKL tI2SVKH Sr tI2PVKH P S Figure 37. I2C Bus AC Timing Diagram 13 High-Speed Serial Interfaces (HSSI) The MPC8641D features two Serializer/Deserializer (SerDes) interfaces to be used for high-speed serial interconnect applications. The SerDes1 interface is dedicated for PCI Express data transfers. The SerDes2 can be used for PCI Express and/or Serial RapidIO data transfers. This section describes the common portion of SerDes DC electrical specifications, which is the DC requirement for SerDes Reference Clocks. The SerDes data lane's transmitter and receiver reference circuits are also shown. 13.1 Signal Terms Definition The SerDes utilizes differential signaling to transfer data across the serial link. This section defines terms used in the description and specification of differential signals. Figure 38 shows how the signals are defined. For illustration purpose, only one SerDes lane is used for description. The figure shows waveform for either a transmitter output (SDn_TX and SDn_TX) or a receiver input (SDn_RX and SDn_RX). Each signal swings between A Volts and B Volts where A > B. Using this waveform, the definitions are as follows. To simplify illustration, the following definitions assume that the SerDes transmitter and receiver operate in a fully symmetrical differential signaling environment. 1. Single-Ended Swing The transmitter output signals and the receiver input signals SDn_TX, SDn_TX, SDn_RX and SDn_RX each have a peak-to-peak swing of A - B Volts. This is also referred as each signal wire's Single-Ended Swing. 2. Differential Output Voltage, VOD (or Differential Output Swing): The Differential Output Voltage (or Swing) of the transmitter, VOD, is defined as the difference of the two complimentary output voltages: VSDn_TX - VSDn_TX. The VOD value can be either positive or negative. 3. Differential Input Voltage, VID (or Differential Input Swing): MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 60 Freescale Semiconductor High-Speed Serial Interfaces (HSSI) 4. 5. 6. 7. The Differential Input Voltage (or Swing) of the receiver, VID, is defined as the difference of the two complimentary input voltages: VSDn_RX - VSDn_RX. The VID value can be either positive or negative. Differential Peak Voltage, VDIFFp The peak value of the differential transmitter output signal or the differential receiver input signal is defined as Differential Peak Voltage, VDIFFp = |A - B| Volts. Differential Peak-to-Peak, VDIFFp-p Since the differential output signal of the transmitter and the differential input signal of the receiver each range from A - B to -(A - B) Volts, the peak-to-peak value of the differential transmitter output signal or the differential receiver input signal is defined as Differential Peak-to-Peak Voltage, VDIFFp-p = 2*VDIFFp = 2 * |(A - B)| Volts, which is twice of differential swing in amplitude, or twice of the differential peak. For example, the output differential peak-peak voltage can also be calculated as VTX-DIFFp-p = 2*|VOD|. Differential Waveform The differential waveform is constructed by subtracting the inverting signal (SDn_TX, for example) from the non-inverting signal (SDn_TX, for example) within a differential pair. There is only one signal trace curve in a differential waveform. The voltage represented in the differential waveform is not referenced to ground. Refer to Figure 47 as an example for differential waveform. Common Mode Voltage, Vcm The Common Mode Voltage is equal to one half of the sum of the voltages between each conductor of a balanced interchange circuit and ground. In this example, for SerDes output, Vcm_out = (VSDn_TX + VSDn_TX)/2 = (A + B) / 2, which is the arithmetic mean of the two complimentary output voltages within a differential pair. In a system, the common mode voltage may often differ from one component's output to the other's input. Sometimes, it may be even different between the receiver input and driver output circuits within the same component. It's also referred as the DC offset in some occasion. SDn_TX or SDn_RX A Volts Vcm = (A + B) / 2 SDn_TX or SDn_RX B Volts Differential Swing, VID or VOD = A - B Differential Peak Voltage, VDIFFp = |A - B| Differential Peak-Peak Voltage, VDIFFpp = 2*VDIFFp (not shown) Figure 38. Differential Voltage Definitions for Transmitter or Receiver MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 61 High-Speed Serial Interfaces (HSSI) To illustrate these definitions using real values, consider the case of a CML (Current Mode Logic) transmitter that has a common mode voltage of 2.25 V and each of its outputs, TD and TD, has a swing that goes between 2.5V and 2.0V. Using these values, the peak-to-peak voltage swing of each signal (TD or TD) is 500 mV p-p, which is referred as the single-ended swing for each signal. In this example, since the differential signaling environment is fully symmetrical, the transmitter output's differential swing (VOD) has the same amplitude as each signal's single-ended swing. The differential output signal ranges between 500 mV and -500 mV, in other words, VOD is 500 mV in one phase and -500 mV in the other phase. The peak differential voltage (VDIFFp) is 500 mV. The peak-to-peak differential voltage (VDIFFp-p) is 1000 mV p-p. 13.2 SerDes Reference Clocks The SerDes reference clock inputs are applied to an internal PLL whose output creates the clock used by the corresponding SerDes lanes. The SerDes reference clocks inputs are SDn_REF_CLK and SDn_REF_CLK for PCI Express and Serial RapidIO. The following sections describe the SerDes reference clock requirements and some application information. 13.2.1 SerDes Reference Clock Receiver Characteristics Figure 39 shows a receiver reference diagram of the SerDes reference clocks. * The supply voltage requirements for XVDD_SRDSn are specified in Table 1 and Table 2. * SerDes Reference Clock Receiver Reference Circuit Structure -- The SDn_REF_CLK and SDn_REF_CLK are internally AC-coupled differential inputs as shown in Figure 39. Each differential clock input (SDn_REF_CLK or SDn_REF_CLK) has a 50- termination to SGND followed by on-chip AC-coupling. -- The external reference clock driver must be able to drive this termination. -- The SerDes reference clock input can be either differential or single-ended. Refer to the Differential Mode and Single-ended Mode description below for further detailed requirements. * The maximum average current requirement that also determines the common mode voltage range -- When the SerDes reference clock differential inputs are DC coupled externally with the clock driver chip, the maximum average current allowed for each input pin is 8mA. In this case, the exact common mode input voltage is not critical as long as it is within the range allowed by the maximum average current of 8 mA (refer to the following bullet for more detail), since the input is AC-coupled on-chip. -- This current limitation sets the maximum common mode input voltage to be less than 0.4V (0.4V/50 = 8mA) while the minimum common mode input level is 0.1V above SGND. For example, a clock with a 50/50 duty cycle can be produced by a clock driver with output driven by its current source from 0mA to 16mA (0-0.8V), such that each phase of the differential input has a single-ended swing from 0V to 800mV with the common mode voltage at 400mV. -- If the device driving the SDn_REF_CLK and SDn_REF_CLK inputs cannot drive 50 ohms to SGND DC, or it exceeds the maximum input current limitations, then it must be AC-coupled off-chip. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 62 Freescale Semiconductor High-Speed Serial Interfaces (HSSI) * The input amplitude requirement -- This requirement is described in detail in the following sections. 50 SDn_REF_CLK Input Amp SDn_REF_CLK 50 Figure 39. Receiver of SerDes Reference Clocks 13.2.2 DC Level Requirement for SerDes Reference Clocks The DC level requirement for the MPC8641D SerDes reference clock inputs is different depending on the signaling mode used to connect the clock driver chip and SerDes reference clock inputs as described below. * Differential Mode -- The input amplitude of the differential clock must be between 400mV and 1600mV differential peak-peak (or between 200mV and 800mV differential peak). In other words, each signal wire of the differential pair must have a single-ended swing less than 800mV and greater than 200mV. This requirement is the same for both external DC-coupled or AC-coupled connection. -- For external DC-coupled connection, as described in section 13.2.1, the maximum average current requirements sets the requirement for average voltage (common mode voltage) to be between 100 mV and 400 mV. Figure 40 shows the SerDes reference clock input requirement for DC-coupled connection scheme. -- For external AC-coupled connection, there is no common mode voltage requirement for the clock driver. Since the external AC-coupling capacitor blocks the DC level, the clock driver and the SerDes reference clock receiver operate in different command mode voltages. The SerDes reference clock receiver in this connection scheme has its common mode voltage set to SGND. Each signal wire of the differential inputs is allowed to swing below and above the command mode voltage (SGND). Figure 41 shows the SerDes reference clock input requirement for AC-coupled connection scheme. * Single-ended Mode -- The reference clock can also be single-ended. The SDn_REF_CLK input amplitude (single-ended swing) must be between 400mV and 800mV peak-peak (from Vmin to Vmax) with SDn_REF_CLK either left unconnected or tied to ground. -- The SDn_REF_CLK input average voltage must be between 200 and 400 mV. Figure 42 shows the SerDes reference clock input requirement for single-ended signaling mode. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 63 High-Speed Serial Interfaces (HSSI) -- To meet the input amplitude requirement, the reference clock inputs might need to be DC or AC-coupled externally. For the best noise performance, the reference of the clock could be DC or AC-coupled into the unused phase (SDn_REF_CLK) through the same source impedance as the clock input (SDn_REF_CLK) in use. SDn_REF_CLK 200mV < Input Amplitude or Differential Peak < 800mV Vmax < 800mV 100mV < Vcm < 400mV Vmin > 0V SDn_REF_CLK Figure 40. Differential Reference Clock Input DC Requirements (External DC-Coupled) 200mV < Input Amplitude or Differential Peak < 800mV SDn_REF_CLK Vmax < Vcm + 400mV Vcm Vmin > Vcm - 400mV SDn_REF_CLK Figure 41. Differential Reference Clock Input DC Requirements (External AC-Coupled) 400mV < SDn_REF_CLK Input Amplitude < 800mV SDn_REF_CLK 0V SDn_REF_CLK Figure 42. Single-Ended Reference Clock Input DC Requirements MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 64 Freescale Semiconductor High-Speed Serial Interfaces (HSSI) 13.2.3 * * * Interfacing With Other Differential Signaling Levels With on-chip termination to SGND, the differential reference clocks inputs are HCSL (High-Speed Current Steering Logic) compatible DC-coupled. Many other low voltage differential type outputs like LVDS (Low Voltage Differential Signaling) can be used but may need to be AC-coupled due to the limited common mode input range allowed (100 to 400 mV) for DC-coupled connection. LVPECL outputs can produce signal with too large amplitude and may need to be DC-biased at clock driver output first, then followed with series attenuation resistor to reduce the amplitude, in addition to AC-coupling. NOTE Figure 43 to Figure 46 below are for conceptual reference only. Due to the fact that clock driver chip's internal structure, output impedance and termination requirements are different between various clock driver chip manufacturers, it's very possible that the clock circuit reference designs provided by clock driver chip vendor are different from what is shown below. They might also vary from one vendor to the other. Therefore, Freescale Semiconductor can neither provide the optimal clock driver reference circuits, nor guarantee the correctness of the following clock driver connection reference circuits. The system designer is recommended to contact the selected clock driver chip vendor for the optimal reference circuits with the MPC8641D SerDes reference clock receiver requirement provided in this document. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 65 High-Speed Serial Interfaces (HSSI) Figure 43 shows the SerDes reference clock connection reference circuits for HCSL type clock driver. It assumes that the DC levels of the clock driver chip is compatible with MPC8641D SerDes reference clock input's DC requirement. MPC8641D HCSL CLK Driver Chip CLK_Out 33 SDn_REF_CLK 50 SerDes Refer. CLK Receiver 100 differential PWB trace Clock Driver 33 SDn_REF_CLK CLK_Out Total 50 . Assume clock driver's output impedance is about 16 . 50 Clock driver vendor dependent source termination resistor Figure 43. DC-Coupled Differential Connection with HCSL Clock Driver (Reference Only) Figure 44 shows the SerDes reference clock connection reference circuits for LVDS type clock driver. Since LVDS clock driver's common mode voltage is higher than the MPC8641D SerDes reference clock input's allowed range (100 to 400mV), AC-coupled connection scheme must be used. It assumes the LVDS output driver features 50- termination resistor. It also assumes that the LVDS transmitter establishes its own common mode level without relying on the receiver or other external component. MPC8641D LVDS CLK Driver Chip CLK_Out 10 nF 50 SerDes Refer. CLK Receiver 100 differential PWB trace Clock Driver CLK_Out SDn_REF_CLK 10 nF SDn_REF_CLK 50 Figure 44. AC-Coupled Differential Connection with LVDS Clock Driver (Reference Only) MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 66 Freescale Semiconductor High-Speed Serial Interfaces (HSSI) Figure 45 shows the SerDes reference clock connection reference circuits for LVPECL type clock driver. Since LVPECL driver's DC levels (both common mode voltages and output swing) are incompatible with MPC8641D SerDes reference clock input's DC requirement, AC-coupling has to be used. Figure 45 assumes that the LVPECL clock driver's output impedance is 50. R1 is used to DC-bias the LVPECL outputs prior to AC-coupling. Its value could be ranged from 140 to 240 depending on clock driver vendor's requirement. R2 is used together with the SerDes reference clock receiver's 50- termination resistor to attenuate the LVPECL output's differential peak level such that it meets the MPC8641D SerDes reference clock's differential input amplitude requirement (between 200mV and 800mV differential peak). For example, if the LVPECL output's differential peak is 900mV and the desired SerDes reference clock input amplitude is selected as 600mV, the attenuation factor is 0.67, which requires R2 = 25. Please consult clock driver chip manufacturer to verify whether this connection scheme is compatible with a particular clock driver chip. LVPECL CLK Driver Chip MPC8641D CLK_Out Clock Driver R2 R1 10nF SDn_REF_CLK SerDes Refer. CLK Receiver 100 differential PWB trace R2 10nF SDn_REF_CLK CLK_Out R1 50 50 Figure 45. AC-Coupled Differential Connection with LVPECL Clock Driver (Reference Only) MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 67 High-Speed Serial Interfaces (HSSI) Figure 46 shows the SerDes reference clock connection reference circuits for a single-ended clock driver. It assumes the DC levels of the clock driver are compatible with MPC8641D SerDes reference clock input's DC requirement. Single-Ended CLK Driver Chip MPC8641D Total 50 . Assume clock driver's output impedance is about 16 . Clock Driver CLK_Out 50 SDn_REF_CLK 33 SerDes Refer. CLK Receiver 100 differential PWB trace 50 SDn_REF_CLK 50 Figure 46. Single-Ended Connection (Reference Only) 13.2.4 AC Requirements for SerDes Reference Clocks The clock driver selected should provide a high quality reference clock with low phase noise and cycle-to-cycle jitter. Phase noise less than 100KHz can be tracked by the PLL and data recovery loops and is less of a problem. Phase noise above 15MHz is filtered by the PLL. The most problematic phase noise occurs in the 1-15MHz range. The source impedance of the clock driver should be 50 ohms to match the transmission line and reduce reflections which are a source of noise to the system. Table 47 describes some AC parameters common to PCI Express and Serial RapidIO protocols. Table 47. SerDes Reference Clock Common AC Parameters At recommended operating conditions with XVDD_SRDS1 or XVDD_SRDS2 = 1.1V 5% and 1.05V 5%. Parameter Symbol Min Max Unit Notes Rising Edge Rate Rise Edge Rate 1.0 4.0 V/ns 2, 3 Falling Edge Rate Fall Edge Rate 1.0 4.0 V/ns 2, 3 Differential Input High Voltage VIH +200 mV 2 Differential Input Low Voltage VIL -- mV 2 -200 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 68 Freescale Semiconductor High-Speed Serial Interfaces (HSSI) Table 47. SerDes Reference Clock Common AC Parameters (continued) At recommended operating conditions with XVDD_SRDS1 or XVDD_SRDS2 = 1.1V 5% and 1.05V 5%. Parameter Rising edge rate (SDn_REF_CLK) to falling edge rate (SD n_REF_CLK) matching Symbol Min Max Unit Notes Rise-Fall Matching -- 20 % 1, 4 Notes: 1. Measurement taken from single ended waveform. 2. Measurement taken from differential waveform. 3. Measured from -200 mV to +200 mV on the differential waveform (derived from SDn_REF_CLK minus SDn_REF_CLK). The signal must be monotonic through the measurement region for rise and fall time. The 400 mV measurement window is centered on the differential zero crossing. See Figure 47. 4. Matching applies to rising edge rate for SDn_REF_CLK and falling edge rate for SDn_REF_CLK. It is measured using a 200 mV window centered on the median cross point where SDn_REF_CLK rising meets SDn_REF_CLK falling. The median cross point is used to calculate the voltage thresholds the oscilloscope is to use for the edge rate calculations. The Rise Edge Rate of SD n_REF_CLK should be compared to the Fall Edge Rate of SDn_REF_CLK, the maximum allowed difference should not exceed 20% of the slowest edge rate. See Figure 48. VIH = +200 mV 0.0 V VIL = -200 mV SDn_REF_CLK minus SDn_REF_CLK Figure 47. Differential Measurement Points for Rise and Fall Time SDn_REF_CLK SDn_REF_CLK SDn_REF_CLK SDn_REF_CLK Figure 48. Single-Ended Measurement Points for Rise and Fall Time Matching The other detailed AC requirements of the SerDes Reference Clocks is defined by each interface protocol based on application usage. Refer to the following sections for detailed information: * Section 14.2, "AC Requirements for PCI Express SerDes Clocks" * Section 15.2, "AC Requirements for Serial RapidIO SDn_REF_CLK and SDn_REF_CLK MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 69 PCI Express 13.3 SerDes Transmitter and Receiver Reference Circuits Figure 49 shows the reference circuits for SerDes data lane's transmitter and receiver. 50 SD1_TX n or SD2_TX n SD1_RXn or SD2_RXn 50 Transmitter Receiver 50 SD1_TXn or SD2_TXn SD1_RXn or SD2_RXn 50 Figure 49. SerDes Transmitter and Receiver Reference Circuits The DC and AC specification of SerDes data lanes are defined in each interface protocol section below (PCI Express or Serial Rapid IO) in this document based on the application usage:" * Section 14, "PCI Express" * Section 15, "Serial RapidIO" Note that external AC Coupling capacitor is required for the above two serial transmission protocols with the capacitor value defined in specification of each protocol section. 14 PCI Express This section describes the DC and AC electrical specifications for the PCI Express bus of the MPC8641. 14.1 DC Requirements for PCI Express SDn_REF_CLK and SDn_REF_CLK For more information, see Section 13.1, "DC Requirements for SerDes Reference Clocks." 14.2 AC Requirements for PCI Express SerDes Clocks Table 48 lists AC requirements. Table 48. SDn_REF_CLK and SDn_REF_CLK AC Requirements Symbol tREF Parameter Description REFCLK cycle time tREFCJ REFCLK cycle-to-cycle jitter. Difference in the period of any two adjacent REFCLK cycles tREFPJ Phase jitter. Deviation in edge location with respect to mean edge location Min Typical Max Units Notes - 10 - ns -- -- -- 100 ps -- -50 -- 50 ps -- MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 70 Freescale Semiconductor PCI Express 14.3 Clocking Dependencies The ports on the two ends of a link must transmit data at a rate that is within 600 parts per million (ppm) of each other at all times. This is specified to allow bit rate clock sources with a +/- 300 ppm tolerance. 14.4 Physical Layer Specifications The following is a summary of the specifications for the physical layer of PCI Express on this device. For further details as well as the specifications of the Transport and Data Link layer please use the PCI EXPRESS Base Specification. REV. 1.0a document. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 71 PCI Express 14.4.1 Differential Transmitter (TX) Output Table 49 defines the specifications for the differential output at all transmitters (TXs). The parameters are specified at the component pins. Table 49. Differential Transmitter (TX) Output Specifications Symbol Parameter Min Nom Max Units Comments 399.88 400 400.12 ps Each UI is 400 ps 300 ppm. UI does not account for Spread Spectrum Clock dictated variations. See Note 1. 1.2 V VTX-DIFFp-p = 2*|V TX-D+ - VTX-D-| See Note 2. -4.0 dB Ratio of the V TX-DIFFp-p of the second and following bits after a transition divided by the VTX-DIFFp-p of the first bit after a transition. See Note 2. UI The maximum Transmitter jitter can be derived as TTX-MAX-JITTER = 1 - TTX-EYE= 0.3 UI. See Notes 2 and 3. UI Jitter is defined as the measurement variation of the crossing points (VTX-DIFFp-p = 0 V) in relation to a recovered TX UI. A recovered TX UI is calculated over 3500 consecutive unit intervals of sample data. Jitter is measured using all edges of the 250 consecutive UI in the center of the 3500 UI used for calculating the TX UI. See Notes 2 and 3. UI See Notes 2 and 5 20 mV VTX-CM-ACp = RMS(|VTXD+ - VTXD-|/2 - V TX-CM-DC) VTX-CM-DC = DC(avg) of |VTX-D+ - VTX-D-|/2 See Note 2 100 mV |VTX-CM-DC (during LO) - VTX-CM-Idle-DC (During Electrical mV VTX-CM-DC = DC(avg) of |VTX-D+ - VTX-D-|/2 [LO] VTX-CM-Idle-DC = DC (avg) of |VTX-D+ - VTX-D-|/2 [Electrical Idle] See Note 2. UI Unit Interval VTX-DIFFp-p Differential Peak-to-Peak Output Voltage 0.8 VTX-DE-RATIO De- Emphasized Differential Output Voltage (Ratio) -3.0 TTX-EYE Minimum TX Eye Width 0.70 TTX-EYE-MEDIAN-to- Maximum time between the jitter median and maximum deviation from the median. MAX-JITTER -3.5 0.15 TTX-RISE, TTX-FALL D+/D- TX Output 0.125 Rise/Fall Time VTX-CM-ACp RMS AC Peak Common Mode Output Voltage VTX-CM-DC-ACTIVE- Absolute Delta of DC Common Mode Voltage During LO and Electrical Idle 0 VTX-CM-DC-LINE-DELTA Absolute Delta of DC Common Mode between D+ and D- 0 25 mV |VTX-CM-DC-D+ - VTX-CM-DC-D-| <= 25 mV VTX-CM-DC-D+ = DC(avg) of |VTX-D+| VTX-CM-DC-D- = DC(avg) of |VTX-D-| See Note 2. Electrical Idle differential Peak Output Voltage 0 20 mV VTX-IDLE-DIFFp = |VTX-IDLE-D+ -VTX-IDLE-D-| <= 20 mV See Note 2. IDLE-DELTA VTX-IDLE-DIFFp Idle)|<=100 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 72 Freescale Semiconductor PCI Express Table 49. Differential Transmitter (TX) Output Specifications (continued) Symbol Parameter Min Nom Max Units Comments 600 mV The total amount of voltage change that a transmitter can apply to sense whether a low impedance Receiver is present. See Note 6. 3.6 V The allowed DC Common Mode voltage under any conditions. See Note 6. 90 mA The total current the Transmitter can provide when shorted to its ground UI Minimum time a Transmitter must be in Electrical Idle Utilized by the Receiver to start looking for an Electrical Idle Exit after successfully receiving an Electrical Idle ordered set VTX-RCV-DETECT The amount of voltage change allowed during Receiver Detection VTX-DC-CM The TX DC Common Mode Voltage ITX-SHORT TX Short Circuit Current Limit TTX-IDLE-MIN Minimum time spent in Electrical Idle TTX-IDLE-SET-TO-IDLE Maximum time to transition to a valid Electrical idle after sending an Electrical Idle ordered set 20 UI After sending an Electrical Idle ordered set, the Transmitter must meet all Electrical Idle Specifications within this time. This is considered a debounce time for the Transmitter to meet Electrical Idle after transitioning from LO. TTX-IDLE-TO-DIFF-DATA Maximum time to transition to valid TX specifications after leaving an Electrical idle condition 20 UI Maximum time to meet all TX specifications when transitioning from Electrical Idle to sending differential data. This is considered a debounce time for the TX to meet all TX specifications after leaving Electrical Idle 0 50 RLTX-DIFF Differential Return Loss 12 dB Measured over 50 MHz to 1.25 GHz. See Note 4 RLTX-CM Common Mode Return Loss 6 dB Measured over 50 MHz to 1.25 GHz. See Note 4 ZTX-DIFF-DC DC Differential TX Impedance 80 TX DC Differential mode Low Impedance ZTX-DC Transmitter DC Impedance 40 Required TX D+ as well as D- DC Impedance during all states LTX-SKEW Lane-to-Lane Output Skew 500 + 2 UI ps Static skew between any two Transmitter Lanes within a single Link CTX AC Coupling Capacitor 200 nF All Transmitters shall be AC coupled. The AC coupling is required either within the media or within the transmitting component itself. 75 100 120 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 73 PCI Express Table 49. Differential Transmitter (TX) Output Specifications (continued) Symbol Tcrosslink Parameter Crosslink Random Timeout Min 0 Nom Max Units Comments 1 ms This random timeout helps resolve conflicts in crosslink configuration by eventually resulting in only one Downstream and one Upstream Port. See Note 7. Notes: 1.) No test load is necessarily associated with this value. 2.) Specified at the measurement point into a timing and voltage compliance test load as shown in Figure 52 and measured over any 250 consecutive TX UIs. (Also refer to the transmitter compliance eye diagram shown in Figure 50) 3.) A TTX-EYE = 0.70 UI provides for a total sum of deterministic and random jitter budget of TTX-JITTER-MAX = 0.30 UI for the Transmitter collected over any 250 consecutive TX UIs. The TTX-EYE-MEDIAN-to-MAX-JITTER median is less than half of the total TX jitter budget collected over any 250 consecutive TX UIs. It should be noted that the median is not the same as the mean. The jitter median describes the point in time where the number of jitter points on either side is approximately equal as opposed to the averaged time value. 4.) The Transmitter input impedance shall result in a differential return loss greater than or equal to 12 dB and a common mode return loss greater than or equal to 6 dB over a frequency range of 50 MHz to 1.25 GHz. This input impedance requirement applies to all valid input levels. The reference impedance for return loss measurements is 50 ohms to ground for both the D+ and D- line (that is, as measured by a Vector Network Analyzer with 50 ohm probes--see Figure 52). Note that the series capacitors CTX is optional for the return loss measurement. 5.) Measured between 20-80% at transmitter package pins into a test load as shown in Figure 52 for both VTX-D+ and VTX-D-. 6.) See Section 4.3.1.8 of the PCI Express Base Specifications Rev 1.0a 7.) See Section 4.2.6.3 of the PCI Express Base Specifications Rev 1.0a 14.4.2 Transmitter Compliance Eye Diagrams The TX eye diagram in Figure 50 is specified using the passive compliance/test measurement load (see Figure 52) in place of any real PCI Express interconnect + RX component. There are two eye diagrams that must be met for the transmitter. Both eye diagrams must be aligned in time using the jitter median to locate the center of the eye diagram. The different eye diagrams will differ in voltage depending whether it is a transition bit or a de-emphasized bit. The exact reduced voltage level of the de-emphasized bit will always be relative to the transition bit. The eye diagram must be valid for any 250 consecutive UIs. A recovered TX UI is calculated over 3500 consecutive unit intervals of sample data. The eye diagram is created using all edges of the 250 consecutive UI in the center of the 3500 UI used for calculating the TX UI. NOTE It is recommended that the recovered TX UI is calculated using all edges in the 3500 consecutive UI interval with a fit algorithm using a minimization merit function (i.e., least squares and median deviation fits). MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 74 Freescale Semiconductor PCI Express Figure 50. Minimum Transmitter Timing and Voltage Output Compliance Specifications 14.4.3 Differential Receiver (RX) Input Specifications Table 50 defines the specifications for the differential input at all receivers (RXs). The parameters are specified at the component pins. Table 50. Differential Receiver (RX) Input Specifications Symbol Parameter Min Nom Max Units Comments 400 400.12 ps Each UI is 400 ps 300 ppm. UI does not account for Spread Spectrum Clock dictated variations. See Note 1. 1.200 V VRX-DIFFp-p = 2*|VRX-D+ - VRX-D-| See Note 2. UI The maximum interconnect media and Transmitter jitter that can be tolerated by the Receiver can be derived as TRX-MAX-JITTER = 1 - TRX-EYE= 0.6 UI. See Notes 2 and 3. UI Unit Interval 399.8 8 VRX-DIFFp-p Differential Peak-to-Peak Output Voltage 0.175 TRX-EYE Minimum Receiver Eye Width 0.4 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 75 PCI Express Table 50. Differential Receiver (RX) Input Specifications (continued) Symbol Parameter Min Nom Max Units Comments TRX-EYE-MEDIAN-to-MAX Maximum time between the jitter median and maximum deviation from the median. 0.3 UI Jitter is defined as the measurement variation of the crossing points (VRX-DIFFp-p = 0 V) in relation to a recovered TX UI. A recovered TX UI is calculated over 3500 consecutive unit intervals of sample data. Jitter is measured using all edges of the 250 consecutive UI in the center of the 3500 UI used for calculating the TX UI. See Notes 2, 3 and 7. VRX-CM-ACp AC Peak Common Mode Input Voltage 150 mV VRX-CM-ACp = |VRXD+ - VRXD-|/2 - VRX-CM-DC VRX-CM-DC = DC(avg) of |VRX-D+ - V RX-D-|/2 See Note 2 RLRX-DIFF Differential Return Loss 15 dB Measured over 50 MHz to 1.25 GHz with the D+ and D- lines biased at +300 mV and -300 mV, respectively. See Note 4 RLRX-CM Common Mode Return Loss 6 dB Measured over 50 MHz to 1.25 GHz with the D+ and D- lines biased at 0 V. See Note 4 ZRX-DIFF-DC DC Differential Input Impedance 80 100 120 RX DC Differential mode impedance. See Note 5 ZRX-DC DC Input Impedance 40 50 60 Required RX D+ as well as D- DC Impedance (50 20% tolerance). See Notes 2 and 5. ZRX-HIGH-IMP-DC Powered Down DC Input Impedance Required RX D+ as well as D- DC Impedance when the Receiver terminations do not have power. See Note 6. VRX-IDLE-DET-DIFFp-p Electrical Idle Detect Threshold 175 mV VRX-IDLE-DET-DIFFp-p = 2*|VRX-D+ -VRX-D-| Measured at the package pins of the Receiver TRX-IDLE-DET-DIFF- Unexpected Electrical Idle Enter Detect Threshold Integration Time 10 ms An unexpected Electrical Idle (V RX-DIFFp-p < VRX-IDLE-DET-DIFFp-p) must be recognized no longer than TRX-IDLE-DET-DIFF-ENTERING to signal an unexpected idle condition. -JITTER ENTERTIME 200 k 65 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 76 Freescale Semiconductor PCI Express Table 50. Differential Receiver (RX) Input Specifications (continued) Symbol LTX-SKEW Parameter Total Skew Min Nom Max Units Comments 20 ns Skew across all lanes on a Link. This includes variation in the length of SKP ordered set (e.g. COM and one to five Symbols) at the RX as well as any delay differences arising from the interconnect itself. Notes: 1.) No test load is necessarily associated with this value. 2.) Specified at the measurement point and measured over any 250 consecutive UIs. The test load in Figure 52 should be used as the RX device when taking measurements (also refer to the Receiver compliance eye diagram shown in Figure 51). If the clocks to the RX and TX are not derived from the same reference clock, the TX UI recovered from 3500 consecutive UI must be used as a reference for the eye diagram. 3.) A TRX-EYE = 0.40 UI provides for a total sum of 0.60 UI deterministic and random jitter budget for the Transmitter and interconnect collected any 250 consecutive UIs. The TRX-EYE-MEDIAN-to-MAX-JITTER specification ensures a jitter distribution in which the median and the maximum deviation from the median is less than half of the total. UI jitter budget collected over any 250 consecutive TX UIs. It should be noted that the median is not the same as the mean. The jitter median describes the point in time where the number of jitter points on either side is approximately equal as opposed to the averaged time value. If the clocks to the RX and TX are not derived from the same reference clock, the TX UI recovered from 3500 consecutive UI must be used as the reference for the eye diagram. 4.) The Receiver input impedance shall result in a differential return loss greater than or equal to 15 dB with the D+ line biased to 300 mV and the D- line biased to -300 mV and a common mode return loss greater than or equal to 6 dB (no bias required) over a frequency range of 50 MHz to 1.25 GHz. This input impedance requirement applies to all valid input levels. The reference impedance for return loss measurements for is 50 ohms to ground for both the D+ and D- line (that is, as measured by a Vector Network Analyzer with 50 ohm probes - see Figure 52). Note: that the series capacitors C TX is optional for the return loss measurement. 5.) Impedance during all LTSSM states. When transitioning from a Fundamental Reset to Detect (the initial state of the LTSSM) there is a 5 ms transition time before Receiver termination values must be met on all un-configured Lanes of a Port. 6.) The RX DC Common Mode Impedance that exists when no power is present or Fundamental Reset is asserted. This helps ensure that the Receiver Detect circuit will not falsely assume a Receiver is powered on when it is not. This term must be measured at 300 mV above the RX ground. 7.) It is recommended that the recovered TX UI is calculated using all edges in the 3500 consecutive UI interval with a fit algorithm using a minimization merit function. Least squares and median deviation fits have worked well with experimental and simulated data. 14.5 Receiver Compliance Eye Diagrams The RX eye diagram in Figure 51 is specified using the passive compliance/test measurement load (see Figure 52) in place of any real PCI Express RX component. Note: In general, the minimum Receiver eye diagram measured with the compliance/test measurement load (see Figure 52) will be larger than the minimum Receiver eye diagram measured over a range of systems at the input Receiver of any real PCI Express component. The degraded eye diagram at the input Receiver is due to traces internal to the package as well as silicon parasitic characteristics which cause the real PCI Express component to vary in impedance from the compliance/test measurement load. The input Receiver eye diagram is implementation specific and is not specified. RX component designer should provide additional margin to adequately compensate for the degraded minimum Receiver eye diagram (shown in Figure 51) expected at the input Receiver based on some adequate combination of system simulations and the Return Loss measured looking into the RX package and silicon. The RX eye diagram must be aligned in time using the jitter median to locate the center of the eye diagram. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 77 PCI Express The eye diagram must be valid for any 250 consecutive UIs. A recovered TX UI is calculated over 3500 consecutive unit intervals of sample data. The eye diagram is created using all edges of the 250 consecutive UI in the center of the 3500 UI used for calculating the TX UI. NOTE The reference impedance for return loss measurements is 50 to ground for both the D+ and D- line (i.e., as measured by a Vector Network Analyzer with 50 probes--see Figure 52). Note that the series capacitors, CTX, are optional for the return loss measurement. Figure 51. Minimum Receiver Eye Timing and Voltage Compliance Specification 14.5.1 Compliance Test and Measurement Load The AC timing and voltage parameters must be verified at the measurement point, as specified within 0.2 inches of the package pins, into a test/measurement load shown in Figure 52. NOTE The allowance of the measurement point to be within 0.2 inches of the package pins is meant to acknowledge that package/board routing may benefit from D+ and D- not being exactly matched in length at the package pin boundary. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 78 Freescale Semiconductor Serial RapidIO Figure 52. Compliance Test/Measurement Load 15 Serial RapidIO This section describes the DC and AC electrical specifications for the RapidIO interface of the MPC8641, for the LP-Serial physical layer. The electrical specifications cover both single and multiple-lane links. Two transmitter types (short run and long run) on a single receiver are specified for each of three baud rates, 1.25, 2.50, and 3.125 GBaud. Two transmitter specifications allow for solutions ranging from simple board-to-board interconnect to driving two connectors across a backplane. A single receiver specification is given that will accept signals from both the short run and long run transmitter specifications. The short run transmitter specifications should be used mainly for chip-to-chip connections on either the same printed circuit board or across a single connector. This covers the case where connections are made to a mezzanine (daughter) card. The minimum swings of the short run specification reduce the overall power used by the transceivers. The long run transmitter specifications use larger voltage swings that are capable of driving signals across backplanes. This allows a user to drive signals across two connectors and a backplane. The specifications allow a distance of at least 50 cm at all baud rates. All unit intervals are specified with a tolerance of +/- 100 ppm. The worst case frequency difference between any transmit and receive clock will be 200 ppm. To ensure interoperability between drivers and receivers of different vendors and technologies, AC coupling at the receiver input must be used. 15.1 DC Requirements for Serial RapidIO SDn_REF_CLK and SDn_REF_CLK For more information, see Section 13.1, "DC Requirements for SerDes Reference Clocks." MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 79 Serial RapidIO 15.2 AC Requirements for Serial RapidIO SDn_REF_CLK and SDn_REF_CLK Table 51 lists AC requirements. Table 51. SDn_REF_CLK and SDn_REF_CLK AC Requirements Symbol Parameter Description Min Typical Max Units REFCLK cycle time -- 10(8) -- ns tREFCJ REFCLK cycle-to-cycle jitter. Difference in the period of any two adjacent REFCLK cycles -- -- 80 ps tREFPJ Phase jitter. Deviation in edge location with respect to mean edge location -40 -- 40 ps tREF 15.3 Comments 8 ns applies only to serial RapidIO with 125-MHz reference clock -- Signal Definitions LP-Serial links use differential signaling. This section defines terms used in the description and specification of differential signals. Figure 53 shows how the signals are defined. The figures show waveforms for either a transmitter output (TD and TD) or a receiver input (RD and RD). Each signal swings between A Volts and B Volts where A > B. Using these waveforms, the definitions are as follows: 8. The transmitter output signals and the receiver input signals TD, TD, RD and RD each have a peak-to-peak swing of A - B Volts 9. The differential output signal of the transmitter, VOD, is defined as VTD-VTD 10. The differential input signal of the receiver, VID, is defined as VRD-VRD 11. The differential output signal of the transmitter and the differential input signal of the receiver each range from A - B to -(A - B) Volts 12. The peak value of the differential transmitter output signal and the differential receiver input signal is A - B Volts 13. The peak-to-peak value of the differential transmitter output signal and the differential receiver input signal is 2 * (A - B) Volts MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 80 Freescale Semiconductor Serial RapidIO TD or RD A Volts TD or RD B Volts Differential Peak-Peak = 2 * (A-B) Figure 53. Differential Peak-Peak Voltage of Transmitter or Receiver To illustrate these definitions using real values, consider the case of a CML (Current Mode Logic) transmitter that has a common mode voltage of 2.25 V and each of its outputs, TD and TD, has a swing that goes between 2.5V and 2.0V. Using these values, the peak-to-peak voltage swing of the signals TD and TD is 500 mV p-p. The differential output signal ranges between 500 mV and -500 mV. The peak differential voltage is 500 mV. The peak-to-peak differential voltage is 1000 mV p-p. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 81 Serial RapidIO 15.4 Equalization With the use of high speed serial links, the interconnect media will cause degradation of the signal at the receiver. Effects such as Inter-Symbol Interference (ISI) or data dependent jitter are produced. This loss can be large enough to degrade the eye opening at the receiver beyond what is allowed in the specification. To negate a portion of these effects, equalization can be used. The most common equalization techniques that can be used are: * A passive high pass filter network placed at the receiver. This is often referred to as passive equalization. * The use of active circuits in the receiver. This is often referred to as adaptive equalization. 15.5 Explanatory Note on Transmitter and Receiver Specifications AC electrical specifications are given for transmitter and receiver. Long run and short run interfaces at three baud rates (a total of six cases) are described. The parameters for the AC electrical specifications are guided by the XAUI electrical interface specified in Clause 47 of IEEE 802.3ae-2002. XAUI has similar application goals to serial RapidIO, as described in Section 8.1. The goal of this standard is that electrical designs for serial RapidIO can reuse electrical designs for XAUI, suitably modified for applications at the baud intervals and reaches described herein. 15.6 Transmitter Specifications LP-Serial transmitter electrical and timing specifications are stated in the text and tables of this section. The differential return loss, S11, of the transmitter in each case shall be better than * -10 dB for (Baud Frequency)/10 < Freq(f) < 625 MHz, and * -10 dB + 10log(f/625 MHz) dB for 625 MHz Freq(f) Baud Frequency The reference impedance for the differential return loss measurements is 100 Ohm resistive. Differential return loss includes contributions from on-chip circuitry, chip packaging and any off-chip components related to the driver. The output impedance requirement applies to all valid output levels. It is recommended that the 20%-80% rise/fall time of the transmitter, as measured at the transmitter output, in each case have a minimum value 60 ps. It is recommended that the timing skew at the output of an LP-Serial transmitter between the two signals that comprise a differential pair not exceed 25 ps at 1.25 GB, 20 ps at 2.50 GB and 15 ps at 3.125 GB. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 82 Freescale Semiconductor Serial RapidIO Table 52. Short Run Transmitter AC Timing Specifications--1.25 GBaud Range Characteristic Symbol Unit Min Notes Max Output Voltage, VO -0.40 2.30 Volts Differential Output Voltage VDIFFPP 500 1000 mV p-p Deterministic Jitter JD 0.17 UI p-p Total Jitter JT 0.35 UI p-p Multiple output skew SMO 1000 ps Skew at the transmitter output between lanes of a multilane link Unit Interval UI 800 ps +/- 100 ppm 800 Voltage relative to COMMON of either signal comprising a differential pair Table 53. Short Run Transmitter AC Timing Specifications--2.5 GBaud Range Characteristic Symbol Unit Min Notes Max Output Voltage, VO -0.40 2.30 Volts Differential Output Voltage VDIFFPP 500 1000 mV p-p Deterministic Jitter JD 0.17 UI p-p Total Jitter JT 0.35 UI p-p Multiple Output skew SMO 1000 ps Skew at the transmitter output between lanes of a multilane link Unit Interval UI 400 ps +/- 100 ppm 400 Voltage relative to COMMON of either signal comprising a differential pair Table 54. Short Run Transmitter AC Timing Specifications--3.125 GBaud Range Characteristic Symbol Unit Min Notes Max Output Voltage, VO -0.40 2.30 Volts Differential Output Voltage VDIFFPP 500 1000 mV p-p Deterministic Jitter JD 0.17 UI p-p Total Jitter JT 0.35 UI p-p Voltage relative to COMMON of either signal comprising a differential pair MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 83 Serial RapidIO Table 54. Short Run Transmitter AC Timing Specifications--3.125 GBaud (continued) Range Characteristic Symbol Unit Min Multiple output skew SMO Unit Interval UI 320 Notes Max 1000 ps Skew at the transmitter output between lanes of a multilane link 320 ps +/- 100 ppm Table 55. Long Run Transmitter AC Timing Specifications--1.25 GBaud Range Characteristic Symbol Unit Min Notes Max Output Voltage, VO -0.40 2.30 Volts Differential Output Voltage VDIFFPP 800 1600 mV p-p Deterministic Jitter JD 0.17 UI p-p Total Jitter JT 0.35 UI p-p Multiple output skew SMO 1000 ps Skew at the transmitter output between lanes of a multilane link Unit Interval UI 800 ps +/- 100 ppm 800 Voltage relative to COMMON of either signal comprising a differential pair Table 56. Long Run Transmitter AC Timing Specifications--2.5 GBaud Range Characteristic Symbol Unit Min Notes Max Output Voltage, VO -0.40 2.30 Volts Differential Output Voltage VDIFFPP 800 1600 mV p-p Deterministic Jitter JD 0.17 UI p-p Total Jitter JT 0.35 UI p-p Multiple output skew SMO 1000 ps Skew at the transmitter output between lanes of a multilane link Unit Interval UI 400 ps +/- 100 ppm 400 Voltage relative to COMMON of either signal comprising a differential pair MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 84 Freescale Semiconductor Serial RapidIO Table 57. Long Run Transmitter AC Timing Specifications--3.125 GBaud Range Characteristic Symbol Unit Min Notes Max Output Voltage, VO -0.40 2.30 Volts Differential Output Voltage VDIFFPP 800 1600 mV p-p Deterministic Jitter JD 0.17 UI p-p Total Jitter JT 0.35 UI p-p Multiple output skew SMO 1000 ps Skew at the transmitter output between lanes of a multilane link Unit Interval UI 320 ps +/- 100 ppm 320 Voltage relative to COMMON of either signal comprising a differential pair Transmitter Differential Output Voltage For each baud rate at which an LP-Serial transmitter is specified to operate, the output eye pattern of the transmitter shall fall entirely within the unshaded portion of the Transmitter Output Compliance Mask shown in Figure 54 with the parameters specified in Table 58 when measured at the output pins of the device and the device is driving a 100 Ohm +/-5% differential resistive load. The output eye pattern of an LP-Serial transmitter that implements pre-emphasis (to equalize the link and reduce inter-symbol interference) need only comply with the Transmitter Output Compliance Mask when pre-emphasis is disabled or minimized. VDIFF max VDIFF min 0 -VDIFF min -VDIFF max 0 A B 1-B 1-A 1 Time in UI Figure 54. Transmitter Output Compliance Mask MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 85 Serial RapidIO Table 58. Transmitter Differential Output Eye Diagram Parameters VDIFFmin (mV) VDIFFmax (mV) A (UI) B (UI) 1.25 GBaud short range 250 500 0.175 0.39 1.25 GBaud long range 400 800 0.175 0.39 2.5 GBaud short range 250 500 0.175 0.39 2.5 GBaud long range 400 800 0.175 0.39 3.125 GBaud short range 250 500 0.175 0.39 3.125 GBaud long range 400 800 0.175 0.39 Transmitter Type 15.7 Receiver Specifications LP-Serial receiver electrical and timing specifications are stated in the text and tables of this section. Receiver input impedance shall result in a differential return loss better that 10 dB and a common mode return loss better than 6 dB from 100 MHz to (0.8)*(Baud Frequency). This includes contributions from on-chip circuitry, the chip package and any off-chip components related to the receiver. AC coupling components are included in this requirement. The reference impedance for return loss measurements is 100 Ohm resistive for differential return loss and 25 Ohm resistive for common mode. Table 59. Receiver AC Timing Specifications--1.25 GBaud Range Characteristic Symbol Unit Min Differential Input Voltage VIN 200 Deterministic Jitter Tolerance JD Combined Deterministic and Random Jitter Tolerance Notes Max mV p-p Measured at receiver 0.37 UI p-p Measured at receiver JDR 0.55 UI p-p Measured at receiver Total Jitter Tolerance1 JT 0.65 UI p-p Measured at receiver Multiple Input Skew SMI 24 ns Skew at the receiver input between lanes of a multilane link Bit Error Rate BER 10-12 Unit Interval UI ps +/- 100 ppm 800 1600 800 Note: 1. Total jitter is composed of three components, deterministic jitter, random jitter and single frequency sinusoidal jitter. The sinusoidal jitter may have any amplitude and frequency in the unshaded region of Figure 55. The sinusoidal jitter component is included to ensure margin for low frequency jitter, wander, noise, crosstalk and other variable system effects. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 86 Freescale Semiconductor Serial RapidIO Table 60. Receiver AC Timing Specifications--2.5 GBaud Range Characteristic Symbol Unit Min Differential Input Voltage VIN 200 Deterministic Jitter Tolerance JD Combined Deterministic and Random Jitter Tolerance Notes Max 1600 mV p-p Measured at receiver 0.37 UI p-p Measured at receiver JDR 0.55 UI p-p Measured at receiver Total Jitter Tolerance1 JT 0.65 UI p-p Measured at receiver Multiple Input Skew SMI 24 ns Skew at the receiver input between lanes of a multilane link Bit Error Rate BER 10-12 Unit Interval UI ps +/- 100 ppm 400 400 Note: 1. Total jitter is composed of three components, deterministic jitter, random jitter and single frequency sinusoidal jitter. The sinusoidal jitter may have any amplitude and frequency in the unshaded region of Figure 55. The sinusoidal jitter component is included to ensure margin for low frequency jitter, wander, noise, crosstalk and other variable system effects. Table 61. Receiver AC Timing Specifications--3.125 GBaud Range Characteristic Symbol Unit Min Differential Input Voltage VIN 200 Deterministic Jitter Tolerance JD Combined Deterministic and Random Jitter Tolerance Notes Max mV p-p Measured at receiver 0.37 UI p-p Measured at receiver JDR 0.55 UI p-p Measured at receiver Total Jitter Tolerance1 JT 0.65 UI p-p Measured at receiver Multiple Input Skew SMI 22 ns Skew at the receiver input between lanes of a multilane link Bit Error Rate BER 10-12 Unit Interval UI ps +/- 100 ppm 320 1600 320 Note: 1. Total jitter is composed of three components, deterministic jitter, random jitter and single frequency sinusoidal jitter. The sinusoidal jitter may have any amplitude and frequency in the unshaded region of Figure 55. The sinusoidal jitter component is included to ensure margin for low frequency jitter, wander, noise, crosstalk and other variable system effects. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 87 Serial RapidIO 8.5 UI p-p Sinusoidal Jitter Amplitude 0.10 UI p-p 22.1 kHz 1.875 MHz 20 MHz Frequency Figure 55. Single Frequency Sinusoidal Jitter Limits 15.8 Receiver Eye Diagrams For each baud rate at which an LP-Serial receiver is specified to operate, the receiver shall meet the corresponding Bit Error Rate specification (Table 59, Table 60, Table 61) when the eye pattern of the receiver test signal (exclusive of sinusoidal jitter) falls entirely within the unshaded portion of the Receiver Input Compliance Mask shown in Figure 56 with the parameters specified in Table 62. The eye pattern of the receiver test signal is measured at the input pins of the receiving device with the device replaced with a 100 Ohm +/- 5% differential resistive load. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 88 Freescale Semiconductor Serial RapidIO Receiver Differential Input Voltage VDIFF max VDIFF min 0 -V DIFF min -V DIFF max A 0 B 1-B 1-A 1 Time (UI) Figure 56. Receiver Input Compliance Mask Table 62. Receiver Input Compliance Mask Parameters Exclusive of Sinusoidal Jitter VDIFFmin (mV) VDIFFmax (mV) A (UI) B (UI) 1.25 GBaud 100 800 0.275 0.400 2.5 GBaud 100 800 0.275 0.400 3.125 GBaud 100 800 0.275 0.400 Receiver Type 15.9 Measurement and Test Requirements Since the LP-Serial electrical specification are guided by the XAUI electrical interface specified in Clause 47 of IEEE 802.3ae-2002, the measurement and test requirements defined here are similarly guided by Clause 47. In addition, the CJPAT test pattern defined in Annex 48A of IEEE802.3ae-2002 is specified as the test pattern for use in eye pattern and jitter measurements. Annex 48B of IEEE802.3ae-2002 is recommended as a reference for additional information on jitter test methods. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 89 Serial RapidIO 15.9.1 Eye Template Measurements For the purpose of eye template measurements, the effects of a single-pole high pass filter with a 3 dB point at (Baud Frequency)/1667 is applied to the jitter. The data pattern for template measurements is the Continuous Jitter Test Pattern (CJPAT) defined in Annex 48A of IEEE802.3ae. All lanes of the LP-Serial link shall be active in both the transmit and receive directions, and opposite ends of the links shall use asynchronous clocks. Four lane implementations shall use CJPAT as defined in Annex 48A. Single lane implementations shall use the CJPAT sequence specified in Annex 48A for transmission on lane 0. The amount of data represented in the eye shall be adequate to ensure that the bit error ratio is less than 10-12. The eye pattern shall be measured with AC coupling and the compliance template centered at 0 Volts differential. The left and right edges of the template shall be aligned with the mean zero crossing points of the measured data eye. The load for this test shall be 100 Ohms resistive +/- 5% differential to 2.5 GHz. 15.9.2 Jitter Test Measurements For the purpose of jitter measurement, the effects of a single-pole high pass filter with a 3 dB point at (Baud Frequency)/1667 is applied to the jitter. The data pattern for jitter measurements is the Continuous Jitter Test Pattern (CJPAT) pattern defined in Annex 48A of IEEE802.3ae. All lanes of the LP-Serial link shall be active in both the transmit and receive directions, and opposite ends of the links shall use asynchronous clocks. Four lane implementations shall use CJPAT as defined in Annex 48A. Single lane implementations shall use the CJPAT sequence specified in Annex 48A for transmission on lane 0. Jitter shall be measured with AC coupling and at 0 Volts differential. Jitter measurement for the transmitter (or for calibration of a jitter tolerance setup) shall be performed with a test procedure resulting in a BER curve such as that described in Annex 48B of IEEE802.3ae. 15.9.3 Transmit Jitter Transmit jitter is measured at the driver output when terminated into a load of 100 Ohms resistive +/- 5% differential to 2.5 GHz. 15.9.4 Jitter Tolerance Jitter tolerance is measured at the receiver using a jitter tolerance test signal. This signal is obtained by first producing the sum of deterministic and random jitter defined in Section 8.6 and then adjusting the signal amplitude until the data eye contacts the 6 points of the minimum eye opening of the receive template shown in Figure 8-4 and Table 8-11. Note that for this to occur, the test signal must have vertical waveform symmetry about the average value and have horizontal symmetry (including jitter) about the mean zero crossing. Eye template measurement requirements are as defined above. Random jitter is calibrated using a high pass filter with a low frequency corner at 20 MHz and a 20 dB/decade roll-off below this. The required sinusoidal jitter specified in Section 8.6 is then added to the signal and the test load is replaced by the receiver being tested. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 90 Freescale Semiconductor Package 16 Package This section details package parameters and dimensions. 16.1 Package Parameters for the MPC8641 The package parameters are as provided in the following list. The package type is 33 mm x 33 mm, 1023 pins. There are two package options: high-lead Flip Chip-Ceramic Ball Grid Array (FC-CBGA), and lead-free (FC-CBGA). For all package types: Die size Package outline Interconnects Pitch Total Capacitor count 12.1 mm x 14.7 mm 33 mm x 33 mm 1023 1 mm 43 caps; 100 nF each For high-lead FC-CBGA (package option: HCTE1 HX) Maximum module height Minimum module height Solder Balls Ball diameter (typical2) 2.97 mm 2.47 mm 89.5% Pb 10.5% Sn 0.60 mm For RoHS lead-free FC-CBGA (package option: HCTE1 VU) Maximum module height Minimum module height Solder Balls Ball diameter (typical2) 1 2 2.77 mm 2.27 mm 95.5% Sn 4.0% Ag 0.5% Cu 0.60 mm High-coefficient of thermal expansion Typical ball diameter is before reflow MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 91 Package 16.2 Mechanical Dimensions of the MPC8641 FC-CBGA The mechanical dimensions and bottom surface nomenclature of the MPC8641D (dual core) and MPC8641 (single core) high-lead FC-CBGA (package option: HCTE HX) and lead-free FC-CBGA (package option: HCTE VU) are shown respectfully in Figure 57 and Figure 58. Figure 57. MPC8641D High-Head FC-CBGA Dimensions MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 92 Freescale Semiconductor Package 1. 2. 3. 4. 5. 6. 7. NOTES for Figure 57 All dimensions are in millimeters. Dimensions and tolerances per ASME Y14.5M-1994. Maximum solder ball diameter measured parallel to datum A. Datum A, the seating plane, is defined by the spherical crowns of the solder balls. Capacitors may not be present on all devices. Caution must be taken not to short capacitors or expose metal capacitor pads on package top. All dimensions symmetrical about centerlines unless otherwise specified. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 93 Package Figure 58. MPC8641D Lead-Free FC-CBGA Dimensions MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 94 Freescale Semiconductor Signal Listings 1. 2. 3. 4. 5. 6. 7. NOTES for Figure 58 All dimensions are in millimeters. Dimensions and tolerances per ASME Y14.5M-1994. Maximum solder ball diameter measured parallel to datum A. Datum A, the seating plane, is defined by the spherical crowns of the solder balls. Capacitors may not be present on all devices. Caution must be taken not to short capacitors or expose metal capacitor pads on package top. All dimensions symmetrical about centerlines unless otherwise specified. 17 Signal Listings Table 63 provides the pin assignments for the signals. Notes for the signal changes on the single core device (MPC8641) are italicized and prefixed by "S". Table 63. MPC8641 Signal Reference by Functional Block Name1 Package Pin Number Pin Type Power Supply Notes DDR Memory Interface 1 Signals2,3 D1_MDQ[0:63] D15, A14, B12, D12, A15, B15, B13, C13, C11, D11, D9, A8, A12, A11, A9, B9, F11, G12, K11, K12, E10, E9, J11, J10, G8, H10, L9, L7, F10, G9, K9, K8, AC6, AC7, AG8, AH9, AB6, AB8, AE9, AF9, AL8, AM8, AM10, AK11, AH8, AK8, AJ10, AK10, AL12, AJ12, AL14, AM14, AL11, AM11, AM13, AK14, AM15, AJ16, AK18, AL18, AJ15, AL15, AL17, AM17 I/O D1_GVDD D1_MECC[0:7] M8, M7, R8, T10, L11, L10, P9, R10 I/O D1_GVDD D1_MDM[0:8] C14, A10, G11, H9, AD7, AJ9, AM12, AK16, N10 O D1_GVDD D1_MDQS[0:8] A13, C10, H12, J7, AE8, AM9, AK13, AK17, N9 I/O D1_GVDD D1_MDQS[0:8] D14, B10, H13, J8, AD8, AL9, AJ13, AM16, P10 I/O D1_GVDD D1_MBA[0:2] AA8, AA10, T9 O D1_GVDD D1_MA[0:15] Y10, W8, W9, V7, V8, U6, V10, U9, U7, U10, Y9, T6, T8, AE12, R7, P6 O D1_GVDD D1_MWE AB11 O D1_GVDD D1_MRAS AB12 O D1_GVDD D1_MCAS AC10 O D1_GVDD MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 95 Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number Pin Type Power Supply AB9, AD10, AC12, AD11 O D1_GVDD P7, M10, N8, M11 O D1_GVDD D1_MCK[0:5] W6, E13, AH11, Y7, F14, AG10 O D1_GVDD D1_MCK[0:5] Y6, E12, AH12, AA7, F13, AG11 O D1_GVDD D1_MODT[0:3] AC9, AF12, AE11, AF10 O D1_GVDD D1_MDIC[0:1] E15, G14 IO D1_GVDD 27 DDR Port 1 reference voltage D1_GVDD /2 3 D1_MCS[0:3] D1_MCKE[0:3] D1_MVREF AM18 Notes 23 DDR Memory Interface 2 Signals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and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 96 Freescale Semiconductor Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number D2_MDIC[0:1] D2_MVREF F8, F7 A18 Pin Type Power Supply Notes IO D2_GVDD 27 DDR Port 2 reference voltage D2_GVDD /2 3 High Speed I/O Interface 1 (SERDES 1)4 SD1_TX[0:7] L26, M24, N26, P24, R26, T24, U26, V24 O SVDD SD1_TX[0:7] L27, M25, N27, P25, R27, T25, U27, V25 O SVDD SD1_RX[0:7] J32, K30, L32, M30, T30, U32, V30, W32 I SVDD SD1_RX[0:7] J31, K29, L31, M29, T29, U31, V29, W31 I SVDD SD1_REF_CLK N32 I SVDD SD1_REF_CLK N31 I SVDD SD1_IMP_CAL_TX Y26 Analog SVDD 19 SD1_IMP_CAL_RX J28 Analog SVDD 30 SD1_PLL_TPD U28 O SVDD 13, 17 SD1_PLL_TPA T28 Analog SVDD 13, 18 SD1_DLL_TPD N28 O SVDD 13, 17 SD1_DLL_TPA P31 Analog SVDD 13, 18 High Speed I/O Interface 2 (SERDES 2)4 SD2_TX[0:3] Y24, AA27, AB25, AC27 O SVDD SD2_TX[4:7] AE27, AG27, AJ27, AL27 O SVDD SD2_TX[0:3] Y25, AA28, AB26, AC28 O SVDD SD2_TX[4:7] AE28, AG28, AJ28, AL28 O SVDD 34 SD2_RX[0:3] Y30, AA32, AB30, AC32 I SVDD 32 SD2_RX[4:7] AH30, AJ32, AK30, AL32 I SVDD 32, 35 SD2_RX[0:3] Y29, AA31, AB29, AC31 I SVDD SD2_RX[4:7] AH29, AJ31, AK29, AL31 I SVDD SD2_REF_CLK AE32 I SVDD SD2_REF_CLK AE31 I SVDD SD2_IMP_CAL_TX AM29 Analog SVDD 34 35 19 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 97 Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number Pin Type Power Supply Notes SD2_IMP_CAL_RX AA26 Analog SVDD 30 SD2_PLL_TPD AF29 O SVDD 13, 17 SD2_PLL_TPA AF31 Analog SVDD 13, 18 SD2_DLL_TPD AD29 O SVDD 13, 17 SD2_DLL_TPA AD30 Analog SVDD 13, 18 Special Connection Requirement pins No Connects K24, K25, P28, P29, W26, W27, AD25, AD26 - - 13 Reserved H30, R32, V28, AG32 - - 14 Reserved H29, R31, W28, AG31 - - 15 Reserved AD24, AG26 - - 16 Ethernet Miscellaneous Signals5 EC1_GTX_CLK125 AL23 I LVDD 39 EC2_GTX_CLK125 AM23 I TVDD 39 EC_MDC G31 O OVDD EC_MDIO G32 I/O OVDD AF25, AC23,AG24, AG23, AE24, AE23, AE22, AD22 O LVDD 6, 10 TSEC1_TX_EN AB22 O LVDD 36 TSEC1_TX_ER AH26 O LVDD TSEC1_TX_CLK AC22 I LVDD 40 TSEC1_GTX_CLK AH25 O LVDD 41 TSEC1_CRS AM24 I/O LVDD 37 TSEC1_COL AM25 I LVDD AL25, AL24, AK26, AK25, AM26, AF26, AH24, AG25 I LVDD TSEC1_RX_DV AJ24 I LVDD TSEC1_RX_ER AJ25 I LVDD TSEC1_RX_CLK AK24 I LVDD 40 O LVDD 6, 10 eTSEC Port 1 Signals5 TSEC1_TXD[0:7]/ GPOUT[0:7] TSEC1_RXD[0:7]/ GPIN[0:7] 10 eTSEC Port 2 Signals5 TSEC2_TXD[0:3]/ GPOUT[8:15] AB20, AJ23, AJ22, AD19 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 98 Freescale Semiconductor Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number Pin Type Power Supply Notes AH23 O LVDD 6,10, 38 AH21, AG22, AG21 O LVDD 6, 10 TSEC2_TX_EN AB21 O LVDD 36 TSEC2_TX_ER AB19 O LVDD 6, 38 TSEC2_TX_CLK AC21 I LVDD 40 TSEC2_GTX_CLK AD20 O LVDD 41 TSEC2_CRS AE20 I/O LVDD 37 TSEC2_COL AE21 I LVDD AL22, AK22, AM21, AH20, AG20, AF20, AF23, AF22 I LVDD TSEC2_RX_DV AC19 I LVDD TSEC2_RX_ER AD21 I LVDD TSEC2_RX_CLK AM22 I LVDD 40 6 TSEC2_TXD[4]/ GPOUT[12] TSEC2_TXD[5:7]/ GPOUT[13:15] TSEC2_RXD[0:7]/ GPIN[8:15] 10 eTSEC Port 3 Signals5 TSEC3_TXD[0:3] AL21, AJ21, AM20, AJ20 O TVDD TSEC3_TXD[4]/ AM19 O TVDD TSEC3_TXD[5:7] AK21, AL20, AL19 O TVDD 6 TSEC3_TX_EN AH19 O TVDD 36 TSEC3_TX_ER AH17 O TVDD TSEC3_TX_CLK AH18 I TVDD 40 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 99 Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number Pin Type Power Supply Notes TSEC3_GTX_CLK AG19 O TVDD 41 TSEC3_CRS AE15 I/O TVDD 37 TSEC3_COL AF15 I TVDD AJ17, AE16, AH16, AH14, AJ19, AH15, AG16, AE19 I TVDD TSEC3_RX_DV AG15 I TVDD TSEC3_RX_ER AF16 I TVDD TSEC3_RX_CLK AJ18 I TVDD 40 AC18, AC16, AD18, AD17 O TVDD 6 AD16 O TVDD 25 AB18, AB17, AB16 O TVDD 6 TSEC4_TX_EN AF17 O TVDD 36 TSEC4_TX_ER AF19 O TVDD TSEC4_TX_CLK AF18 I TVDD 40 TSEC4_GTX_CLK AG17 O TVDD 41 TSEC4_CRS AB14 I/O TVDD 37 TSEC4_COL AC13 I TVDD AG14, AD13, AF13, AD14, AE14, AB15, AC14, AE17 I TVDD TSEC4_RX_DV AC15 I TVDD TSEC4_RX_ER AF14 I TVDD TSEC4_RX_CLK AG13 I TVDD TSEC3_RXD[0:7] eTSEC Port 4 Signals5 TSEC4_TXD[0:3] TSEC4_TXD[4] TSEC4_TXD[5:7] TSEC4_RXD[0:7] 40 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 100 Freescale Semiconductor Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number Pin Type Power Supply Notes Local Bus Signals5 LAD[0:31] A30, E29, C29, D28, D29, H25, B29, A29, C28, L22, M22, A28, C27, H26, G26, B27, B26, A27, E27, G25, D26, E26, G24, F27, A26, A25, C25, H23, K22, D25, F25, H22 I/O OVDD 6 LDP[0:3] A24, E24, C24, B24 I/O OVDD 6, 22 LA[27:31] J21, K21, G22, F24, G21 O OVDD 6, 22 LCS[0:4] A22, C22, D23, E22, A23 O OVDD 7 LCS[5]/DMA_DREQ[2] B23 O OVDD 7, 9, 10 LCS[6]/DMA_DACK[2] E23 O OVDD 7, 10 LCS[7]/DMA_DDONE[2] F23 O OVDD 7, 10 E21, F21, D22, E20 O OVDD 6 LBCTL D21 O OVDD LALE E19 O OVDD LGPL0/LSDA10 F20 O OVDD 25 LGPL1/LSDWE H20 O OVDD 25 LGPL2/LOE/ LSDRAS J20 O OVDD LGPL3/LSDCAS K20 O OVDD 6 LGPL4/LGTA/ LUPWAIT/LPBSE L21 I/O OVDD 42 LGPL5 J19 O OVDD 6 LCKE H19 O OVDD LCLK[0:2] G19, L19, M20 O OVDD LSYNC_IN M19 I OVDD LSYNC_OUT D20 O OVDD I OVDD LWE[0:3]/ LSDDQM[0:3]/ LBS[0:3] DMA DMA_DREQ[0:1] E31, E32 Signals5 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 101 Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number Pin Type Power Supply Notes DMA_DREQ[2]/LCS[5] B23 I OVDD 9, 10 DMA_DREQ[3]/IRQ[9] B30 I OVDD 10 D32, F30 O OVDD DMA_DACK[2]/LCS[6] E23 O OVDD 10 DMA_DACK[3]/IRQ[10] C30 O OVDD 9, 10 F31, F32 O OVDD DMA_DDONE[2]/LCS[7] F23 O OVDD 10 DMA_DDONE[3]/IRQ[11] D30 O OVDD 9, 10 DMA_DACK[0:1] DMA_DDONE[0:1] Programmable Interrupt Controller Signals 5 MCP_0 F17 I OVDD MCP _1 H17 I OVDD IRQ[0:8] G28, G29, H27, J23, M23, J27, F28, J24, L23 I OVDD IRQ[9]/DMA_DREQ[3] B30 I OVDD 10 IRQ[10]/DMA_DACK[3] C30 I OVDD 9, 10 IRQ[11]/DMA_DDONE[3] D30 I OVDD 9, 10 J26 O OVDD 7, 11 IRQ_OUT 12, S4 DUART Signals5 UART_SIN[0:1] B32, C32 I OVDD UART_SOUT[0:1] D31, A32 O OVDD UART_CTS[0:1] A31, B31 I OVDD UART_RTS[0:1] C31, E30 O OVDD I/O OVDD I2C Signals IIC1_SDA A16 7, 11 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 102 Freescale Semiconductor Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number Pin Type Power Supply Notes IIC1_SCL B17 I/O OVDD 7, 11 IIC2_SDA A21 I/O OVDD 7, 11 IIC2_SCL B21 I/O OVDD 7, 11 System Control Signals5 HRESET B18 I OVDD HRESET_REQ K18 O OVDD SMI_0 L15 I OVDD SMI_1 L16 I OVDD SRESET_0 C20 I OVDD SRESET_1 C21 I OVDD CKSTP_IN L18 I OVDD CKSTP_OUT L17 O OVDD 7, 11 READY/TRIG_OUT J13 O OVDD 10, 25 12, S4 12, S4 Debug Signals5 TRIG_IN J14 I OVDD TRIG_OUT/READY J13 O OVDD 10, 25 F15, K15 O OVDD 6, 10 K14 O OVDD 10, 25 D1_MSRCID[3:4]/ LB_SRCID[3:4] H15, G15 O OVDD 10 D2_MSRCID[0:4] E16, C17, F16, H16, K16 O OVDD D1_MDVAL/LB_DVAL J16 O OVDD D2_MDVAL D19 O OVDD O OVDD D1_MSRCID[0:1]/ LB_SRCID[0:1] D1_MSRCID[2]/ LB_SRCID[2] 10 Power Management Signals5 ASLEEP C19 System Clocking Signals5 SYSCLK G16 I OVDD RTC K17 I OVDD 32 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 103 Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number CLK_OUT Pin Type Power Supply Notes O OVDD 23 I OVDD 26 I OVDD 26 B16 Test Signals5 LSSD_MODE TEST_MODE[0:3] C18 C16, E17, D18, D16 JTAG Signals5 TCK H18 I OVDD TDI J18 I OVDD 24 TDO G18 O OVDD 23 TMS F18 I OVDD 24 TRST A17 I OVDD 24 J17 - - 13 GPOUT[0:7]/ TSEC1_TXD[0:7] AF25, AC23, AG24, AG23, AE24, AE23, AE22, AD22 O OVDD 6, 10 GPIN[0:7]/ TSEC1_RXD[0:7] AL25, AL24, AK26, AK25, AM26, AF26, AH24, AG25 I OVDD 10 GPOUT[8:15]/ TSEC2_TXD[0:7] AB20, AJ23, AJ22, AD19, AH23, AH21, AG22, AG21 O OVDD 10 GPIN[8:15]/ TSEC2_RXD[0:7] AL22, AK22, AM21, AH20, AG20, AF20, AF23, AF22 I OVDD 10 AA11 Thermal - Y11 Thermal - Miscellaneous5 Spare Additional Analog Signals TEMP_ANODE TEMP_CATHODE Sense, Power and GND Signals SENSEVDD_Core0 M14 VDD_Core0 sensing pin 31 SENSEVDD_Core1 U20 VDD_Core1 sensing pin 12,31, S1 SENSEVSS_Core0 P14 Core0 GND sensing pin 31 SENSEVSS_Core1 V20 Core1 GND sensing pin 12, 31, S3 SENSEVDD_PLAT N18 VDD_PLAT sensing pin 28 SENSEVSS_PLAT P18 Platform GND sensing pin 29 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 104 Freescale Semiconductor Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number Pin Type Power Supply D1_GVDD B11, B14, D10, D13, F9, F12, H8, H11, H14, K10, K13, L8, P8, R6, U8, V6, W10, Y8, AA6, AB10, AC8, AD12, AE10, AF8, AG12, AH10, AJ8, AJ14, AK12, AL10, AL16 SDRAM 1 I/O supply D1_GVDD 2.5 - DDR 1.8 DDR2 D2_GVDD B2, B5, B8, D4, D7, E2, F6, G4, H2, J6, K4, L2, M6, N4, P2, T4, U2, W4, Y2, AB4, AC2, AD6, AE4, AF2, AG6, AH4, AJ2, AK6, AL4, AM2 SDRAM 2 I/O supply D2_GVDD 2.5 V - DDR 1.8 V - DDR2 OVDD B22, B25, B28, D17, D24, D27, F19, F22, F26, F29, G17, H21, H24, K19, K23, M21, AM30 DUART, Local Bus, DMA, Multiprocessor Interrupts, System Control & Clocking, Debug, Test, JTAG, Power management, I2C, JTAG and Miscellaneous I/O voltage OVDD 3.3 V LVDD AC20, AD23, AH22 TSEC1 and TSEC2 I/O voltage LVDD 2.5/3.3 V TVDD AC17, AG18, AK20 TSEC3 and TSEC4 I/O voltage TVDD 2.5/3.3 V SVDD H31, J29, K28, K32, L30, M28, M31, N29, R30, T31, U29, V32, W30, Y31, AA29, AB32, AC30, AD31, AE29, AG30, AH31, AJ29, AK32, AL30, AM31 Transceiver Power Supply SerDes K26, L24, M27, N25, P26, R24, R28, T27, U25, V26 Serial I/O Power Supply for SerDes Port 1 XVDD_SRDS1 Serial I/O Power Supply for SerDes Port 2 XVDD_SRDS2 L12, L13, L14, M13, M15, N12, N14, P11, P13, P15, R12, R14, T11, T13, T15, U12, U14, V11, V13, V15, W12, W14, Y12, Y13, Y15, AA12, AA14, AB13 Core 0 voltage supply VDD_Core0 R16, R18, R20, T17, T19, T21, T23, U16, U18, U22, V17, V19, V21, V23, W16, W18, W20, W22, Y17, Y19, Y21, Y23, AA16, AA18, AA20, AA22, AB23, AC24 Core 1 voltage supply XVDD_SRDS1 XVDD_SRDS2 VDD_Core0 VDD_Core1 AA25, AB28, AC26, AD27, AE25, AF28, AH27, AK28, AM27, W24, Y27 Notes SVDD 1.05/1.1 V 1.05/1.1 V 1.05/1.1 V 0.95/1.05/1.1 V VDD_Core1 12, S1 0.95/1.05/1.1 V MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 105 Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number Pin Type Power Supply VDD_PLAT M16, M17, M18, N16, N20, N22, P17, P19, P21, P23, R22 Platform supply voltage VDD_PLAT 1.05/1.1 V AVDD_Core0 B20 Core 0 PLL Supply AVDD_Core0 0.95/1.05/1.1 V AVDD_Core1 A19 Core 1 PLL Supply AVDD_Core1 0.95/1.05/1.1 V AV DD_PLAT B19 Platform PLL supply voltage AV DD_PLAT 1.05/1.1 V AVDD_LB A20 Local Bus PLL supply voltage AVDD_LB 1.05/1.1 V AV DD_SRDS1 P32 SerDes Port 1 PLL & DLL Power Supply AVDD_SRDS1 SerDes Port 2 PLL & DLL Power Supply AVDD_SRDS2 GND - AV DD_SRDS2 GND AF32 C3, C6, C9, C12, C15, C23, C26, E5, E8, E11, E14, E18, E25, E28, F3, G7, G10, G13, G20, G23, G27, G30, H5, J3, J9, J12, J15, J22, J25, K7, L5, L20, M3, M9, M12, N7, N11, N13, N15, N17, N19, N21, N23, P5, P12, P16, P20, P22, R3, R9, R11, R13, R15, R17, R19, R21, R23, T7, T12, T14, T16, T18, T20, T22, U5, U11,U13, U15, U17, U19, U21, U23, V3, V9, V12, V14, V16, V18, V22, W7, W11, W13, W15, W17, W19, W21, W23,Y5, Y14, Y16, Y18, Y20, Y22, AA3, AA9, AA13, AA15, AA17, AA19, AA21, AA23, AB7, AB24, AC5, AC11, AD3, AD9, AD15, AE7, AE13, AE18, AF5, AF11, AF21, AF24, AG3, AG9, AH7, AH13, AJ5, AJ11, AK3, AK9, AK15, AK19, AK23, AL7, AL13 12, S2 1.05/1.1 V 1.05/1.1 V AGND_SRDS1 P30 SerDes Port 1 Ground pin for AVDD_SRDS1 - AGND_SRDS2 AF30 SerDes Port 2 Ground pin for AVDD_SRDS2 - SGND Notes Ground pins for H28, H32, J30, K31, L28, L29, M32, N30, SVDD R29, T32, U30, V31, W29,Y32 AA30, AB31, AC29, AD32, AE30, AG29, AH32, AJ30, AK31, AL29, AM32 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 106 Freescale Semiconductor Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number Pin Type XGND K27, L25, M26, N24, P27, R25, T26, U24, V27, W25, Y28, AA24, AB27, AC25, AD28, AE26, AF27, AH28, AJ26, AK27, AL26, AM28 Ground pins for XVDD_SRDS n Power Supply Notes Reset Configuration Signals20 TSEC1_TXD[0] / AF25 - LVDD TSEC1_TXD[1]/ cfg_platform_freq AC23 - LVDD TSEC1_TXD[2:4]/ cfg_device_id[5:7] AG24, AG23, AE24 - LVDD TSEC1_TXD[5]/ cfg_tsec1_reduce AE23 - LVDD AE22, AD22 - LVDD TSEC2_TXD[0:3]/ cfg_rom_loc[0:3] AB20, AJ23, AJ22, AD19 - LVDD TSEC2_TXD[4], TSEC2_TX_ER/ cfg_dram_type[0:1] AH23, AB19 - LVDD TSEC2_TXD[5]/ cfg_tsec2_reduce AH21 - LVDD TSEC2_TXD[6:7]/ cfg_tsec2_prtcl[0:1] AG22, AG21 - LVDD TSEC3_TXD[0:1]/ cfg_spare[0:1] AL21, AJ21 O TVDD TSEC3_TXD[2]/ cfg_core1_enable AM20 O TVDD TSEC3_TXD[3]/ cfg_core1_lm_offset AJ20 - LVDD TSEC3_TXD[5]/ cfg_tsec3_reduce AK21 - LVDD AL20, AL19 - LVDD TSEC4_TXD[0:3]/ cfg_io_ports[0:3] AC18, AC16, AD18, AD17 - LVDD TSEC4_TXD[5]/ cfg_tsec4_reduce AB18 - LVDD AB17, AB16 - LVDD cfg_alt_boot_vec TSEC1_TXD[6:7]/ cfg_tsec1_prtcl[0:1] TSEC3_TXD[6:7]/ cfg_tsec3_prtcl[0:1] TSEC4_TXD[6:7]/ cfg_tsec4_prtcl[0:1] 21 38 33 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 107 Signal Listings Table 63. MPC8641 Signal Reference by Functional Block (continued) Name1 Package Pin Number Pin Type Power Supply A30, E29, C29, D28, D29, H25, B29, A29, C28, L22, M22, A28, C27, H26, G26, B27, B26, A27, E27, G25, D26, E26, G24, F27, A26, A25, C25, H23, K22, D25, F25, H22 - OVDD LWE[0]/ cfg_cpu_boot E21 - OVDD LWE[1]/ cfg_rio_sys_size F21 - OVDD LWE[2:3]/ cfg_host_agt[0:1] D22, E20 - OVDD LDP[0:3], LA[27] / cfg_core_pll[0:4] A24, E24, C24, B24, J21 - OVDD 22 LA[28:31]/ cfg_sys_pll[0:3] K21, G22, F24, G21 - OVDD 22 LGPL[3], LGPL[5]/ cfg_boot_seq[0:1] K20, J19 - OVDD D1_MSRCID[0]/ cfg_mem_debug F15 - OVDD D1_MSRCID[1]/ cfg_ddr_debug K15 - OVDD LAD[0:31]/ cfg_gpporcr[0:31] Notes Note: 1. Multi-pin signals such as D1_MDQ[0:63] and D2_MDQ[0:63] have their physical package pin numbers listed in order corresponding to the signal names. 2. Stub Series Terminated Logic (SSTL-18 and SSTL-25) type pins. 3. If a DDR port is not used, it is possible to leave the related power supply (Dn_GVDD, Dn_MVREF) turned off at reset. Note that these power supplies can only be powered up again at reset for functionality to occur on the DDR port. 4. Low Voltage Differential Signaling (LVDS) type pins. 5. Low Voltage Transistor-Transistor Logic (LVTTL) type pins. 6. This pin is a reset configuration pin and appears again in the Reset Configuration Signals section of this table. See the Reset Configuration Signals section of this table for config name and connection details. 7. Recommend a weak pull-up resistor (1-10 k) be placed from this pin to its power supply. 8. Recommend a weak pull-down resistor (2-10 k) be placed from this pin to ground. 9. This multiplexed pin has input status in one mode and output in another 10. This pin is a multiplexed signal for different functional blocks and appears more than once in this table. 11. This pin is open drain signal. 12. Functional only on the MPC8641D. 13. These pins should be left floating. 14. These pins should be connected to SV DD. 15. These pins should be pulled to ground with a strong resistor (270- to 330-). 16. These pins should be connected to OVDD. 17.This is a SerDes PLL/DLL digital test signal and is only for factory use. 18. This is a SerDes PLL/DLL analog test signal and is only for factory use. 19. This pin should be pulled to ground with a 100- resistor. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 108 Freescale Semiconductor Clocking 20. The pins in this section are reset configuration pins. Each pin has a weak internal pull-up P-FET which is enabled only when the processor is in the reset state. This pull-up is designed such that it can be overpowered by an external 4.7-k pull-down resistor. However, if the signal is intended to be high after reset, and if there is any device on the net which might pull down the value of the net at reset, then a pullup or active driver is needed. 21. Should be pulled down at reset if platform frequency is at 400 MHz. 22. These pins require 4.7-k pull-up or pull-down resistors and must be driven as they are used to determine PLL configuration ratios at reset. 23. This output is actively driven during reset rather than being tri-stated during reset. 24 These JTAG pins have weak internal pull-up P-FETs that are always enabled. 25. This pin should NOT be pulled down (or driven low) during reset. 26.These are test signals for factory use only and must be pulled up (100- to 1- k.) to OVDD for normal machine operation. 27. Dn_MDIC[0] should be connected to ground with an 18- resistor +/- 1- and Dn_MDIC[1] should be connected Dn_GVDD with an 18- resistor +/- 1-. These pins are used for automatic calibration of the DDR IOs. 28. Pin N18 is recommended as a reference point for determining the voltage of VDD_PLAT and is hence considered as the VDD_PLAT sensing voltage and is called SENSEVDD_PLAT. 29. Pin P18 is recommended as the ground reference point for SENSEVDD_PLAT and is called SENSEVSS_PLAT. 30.This pin should be pulled to ground with a 200- resistor. 31.These pins are connected to the power/ground planes internally and may be used by the core power supply to improve tracking and regulation. 32. Must be tied low if unused 33. These pins may be used as defined functional reset configuration pins in the future. Please include a resistor pull up/down option to allow flexibility of future designs. 34. Used as serial data output for SRIO 1x/4x link. 35. Used as serial data input for SRIO 1x/4x link. 36.This pin requires an external 4.7-k pull-down resistor to prevent PHY from seeing a valid Transmit Enable before it is actively driven. 37.This pin is only an output in FIFO mode when used as Rx Flow Control. 38.This pin functions as cfg_dram_type[0 or 1] at reset and MUST BE VALID BEFORE HRESET ASSERTION in device sleep mode. 39. Should be pulled to ground if unused (such as in FIFO, MII and RMII modes). 40. See Section 18.4.2, "Platform to FIFO Restrictions" for clock speed limitations for this pin when used in FIFO mode. 41. The phase between the output clocks TSEC1_GTX_CLK and TSEC2_GTX_CLK (ports 1 and 2) is no more than 100 ps. The phase between the output clocks TSEC3_GTX_CLK and TSEC4_GTX_CLK (ports 3 and 4) is no more than 100 ps. 42. For systems which boot from Local Bus (GPCM)-controlled flash, a pullup on LGPL4 is required. Special Notes for Single Core Device: S1. Solder ball for this signal will not be populated in the single core package. S2. The PLL filter from VDD_Core1 to AVDD_Core1 should be removed. AVDD_Core1 should be pulled to ground with a weak (2-10 k) resistor. See Section 20.2.1, "PLL Power Supply Filtering" for more details. S3. This pin should be pulled to GND for the single core device. S4. No special requirement for this pin on single core device. Pin should be tied to power supply as directed for dual core. 18 Clocking This section describes the PLL configuration of the MPC8641. Note that the platform clock is identical to the MPX clock. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 109 Clocking 18.1 Clock Ranges Table 64 provides the clocking specifications for the processor cores and Table 65 provides the clocking specifications for the memory bus. Table 66 provides the clocking for the Platform/MPX bus and Table 67 provides the clocking for the Local bus. Table 64. Processor Core Clocking Specifications Maximum Processor Core Frequency Characteristic 1000 MHz e600 core processor frequency 1250MHz 1333MHz 1500 MHz Min Max Min Max Min Max Min Max 800 1000 800 1250 800 1333 800 1500 Unit Notes MHz 1, 2 Notes: 1. Caution: The MPX clock to SYSCLK ratio and e600 core to MPX clock ratio settings must be chosen such that the resulting SYSCLK frequency, e600 (core) frequency, and MPX clock frequency do not exceed their respective maximum or minimum operating frequencies. Refer to Section 18.2, "MPX to SYSCLK PLL Ratio," and Section 18.3, "e600 to MPX clock PLL Ratio," for ratio settings. 2. The minimum e600 core frequency is based on the minimum platform clock frequency of 400 MHz. Table 65. Memory Bus Clocking Specifications Maximum Processor Core Frequency Characteristic Memory bus clock frequency 1000, 1250, 1333, 1500MHz Min Max 200 300 Unit Notes MHz 1, 2 Notes: 1. Caution: The MPX clock to SYSCLK ratio and e600 core to MPX clock ratio settings must be chosen such that the resulting SYSCLK frequency, e600 (core) frequency, and MPX clock frequency do not exceed their respective maximum or minimum operating frequencies. Refer to Section 18.2, "MPX to SYSCLK PLL Ratio," and Section 18.3, "e600 to MPX clock PLL Ratio," for ratio settings. 2. The memory bus clock speed is half the DDR/DDR2 data rate, hence, half the MPX clock frequency. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 110 Freescale Semiconductor Clocking Table 66. Platform/MPX bus Clocking Specifications Maximum Processor Core Frequency Characteristic 1000, 1250, 1333, 1500MHz Platform/MPX bus clock frequency Min Max 400 500-600 Unit Notes MHz 1, 2 Notes: 1. Caution: The MPX clock to SYSCLK ratio and e600 core to MPX clock ratio settings must be chosen such that the resulting SYSCLK frequency, e600 (core) frequency, and MPX clock frequency do not exceed their respective maximum or minimum operating frequencies. Refer to Section 18.2, "MPX to SYSCLK PLL Ratio," and Section 18.3, "e600 to MPX clock PLL Ratio," for ratio settings. 2. Platform/MPX frequencies between 400 and 500 MHz are not supported. Table 67. Local Bus Clocking Specifications Maximum Processor Core Frequency Characteristic 1000, 1250, 1333, 1500MHz Local bus clock speed (for Local Bus Controller) Min Max 25 133 Unit Notes MHz 1 Notes: 1. The Local bus clock speed on LCLK[0:2] is determined by MPX clock divided by the Local Bus PLL ratio programmed in LCRR[CLKDIV]. See the reference manual for the MPC8641D for more information on this. 18.2 MPX to SYSCLK PLL Ratio The MPX clock is the clock that drives the MPX bus, and is also called the platform clock. The frequency of the MPX is set using the following reset signals, as shown in Table 68: * SYSCLK input signal * Binary value on LA[28:31] at power up Note that there is no default for this PLL ratio; these signals must be pulled to the desired values. Also note that the DDR data rate is the determining factor in selecting the MPX bus frequency, since the MPX frequency must equal the DDR data rate. Table 68. MPX:SYSCLK Ratio Binary Value of LA[28:31] Signals MPX:SYSCLK Ratio 0000 Reserved 0001 Reserved MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 111 Clocking Table 68. MPX:SYSCLK Ratio 18.3 Binary Value of LA[28:31] Signals MPX:SYSCLK Ratio 0010 2:1 0011 3:1 0100 4:1 0101 5:1 0110 6:1 0111 Reserved 1000 8:1 1001 9:1 e600 to MPX clock PLL Ratio Table 69 describes the clock ratio between the platform and the e600 core clock. This ratio is determined by the binary value of LDP[0:3], LA[27](cfg_core_pll[0:4] - reset config name) at power up, as shown in Table 69. Table 69. e600 Core to MPX Clock Ratio 18.4 18.4.1 Binary Value of LDP[0:3], LA[27] Signals e600 core: MPX Clock Ratio 01000 2:1 01100 2.5:1 10000 3:1 11100 3.5:1 10100 4:1 01110 4.5:1 Frequency Options SYSCLK to Platform Frequency Options Table 70 shows some SYSCLK frequencies and the expected MPX frequency values based on the MPX clock to SYSCLK ratio. Note that frequencies between 400 MHz and 500 MHz are NOT supported on the MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 112 Freescale Semiconductor Thermal platform. See note regarding cfg_platform_freq in Section 17, "Signal Listings" since it is a reset configuration pin that is related to platform frequency. Table 70. Frequency Options of SYSCLK with Respect to Platform/MPX Clock Speed MPX to SYSCLK Ratio SYSCLK (MHz) 66 83 100 111 133 167 Platform/MPX Frequency (MHz) 1 2 3 1 18.4.2 400 4 400 5 500 6 400 8 533 9 600 500 500 533 555 600 SYSCLK frequency range is 66-167 MHz. Platform clock/ MPX frequency range is 400 MHz, 500-600 MHz. Platform to FIFO Restrictions Please note the following FIFO maximum speed restrictions based on platform speed. For FIFO GMII mode: FIFO TX/RX clock frequency <= platform clock frequency / 4.2 For example, if the platform frequency is 533MHz, the FIFO TX/RX clock frequency should be no more than 127MHz For FIFO encoded mode: FIFO TX/RX clock frequency <= platform clock frequency / 3.2 For example, if the platform frequency is 533MHz, the FIFO TX/RX clock frequency should be no more than 167MHz 19 Thermal This section describes the thermal specifications of the MPC8641. 19.1 Thermal Characteristics Table 71 provides the package thermal characteristics for the MPC8641. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 113 Thermal Table 71. Package Thermal Characteristics1 Characteristic Symbol Value Unit Notes Junction-to-ambient thermal resistance, natural convection, single-layer (1s) board RJA 18 C/W 1, 2 Junction-to-ambient thermal resistance, natural convection, four-layer (2s2p) board RJA 13 C/W 1, 3 Junction-to-ambient thermal resistance, 200 ft/min airflow, single-layer (1s) board RJMA 13 C/W 1, 3 Junction-to-ambient thermal resistance, 200 ft/min airflow, four-layer (2s2p) board RJMA 9 C/W 1, 3 Junction-to-board thermal resistance RJB 5 C/W 4 Junction-to-case thermal resistance RJC < 0.1 C/W 5 Notes: 1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. 2. Per JEDEC JESD51-2 with the single-layer board (JESD51-3) horizontal. 3. Per JEDEC JESD51-6 with the board (JESD51-7) horizontal. 4. Thermal resistance between the die and the printed-circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. 5. This is the thermal resistance between die and case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1) with the calculated case temperature. Actual thermal resistance is less than 0.1 C/W. 19.2 Thermal Management Information This section provides thermal management information for the high coefficient of thermal expansion (HCTE) package for air-cooled applications. Proper thermal control design is primarily dependent on the system-level design--the heat sink, airflow, and thermal interface material. The MPC8641 implements several features designed to assist with thermal management, including the temperature diode. The temperature diode allows an external device to monitor the die temperature in order to detect excessive temperature conditions and alert the system; see Section 19.2.4, "Temperature Diode," for more information. To reduce the die-junction temperature, heat sinks are required; due to the potential large mass of the heat sink, attachment through the printed-circuit board is suggested. In any implementation of a heat sink solution, the force on the die should not exceed ten pounds force (45 newtons). Figure 59 and Figure 52 show a spring clip through the board. Occasionally the spring clip is attached to soldered hooks or to a plastic backing structure. Screw and spring arrangements are also frequently used. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 114 Freescale Semiconductor Thermal Heat Sink HCTE FC-CBGA Package Heat Sink Clip Thermal Interface Material Printed-Circuit Board Figure 59. FC-CBGA Package Exploded Cross-Sectional View with Several Heat Sink Options There are several commercially-available heat sinks for the MPC8641 provided by the following vendors: Aavid Thermalloy 603-224-9988 80 Commercial St. Concord, NH 03301 Internet: www.aavidthermalloy.com Advanced Thermal Solutions 781-769-2800 89 Access Road #27. Norwood, MA02062 Internet: www.qats.com Alpha Novatech 408-749-7601 473 Sapena Ct. #12 Santa Clara, CA 95054 Internet: www.alphanovatech.com Calgreg Thermal Solutions 888-732-6100 60 Alhambra Road, Suite 1 Warwick, RI 02886 Internet: www.calgreg.com International Electronic Research Corporation (IERC)818-842-7277 413 North Moss St. Burbank, CA 91502 Internet: www.ctscorp.com Millennium Electronics (MEI) 408-436-8770 Loroco Sites 671 East Brokaw Road San Jose, CA 95112 Internet: www.mei-thermal.com MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 115 Thermal Tyco Electronics Chip CoolersTM P.O. Box 3668 Harrisburg, PA 17105-3668 Internet: www.chipcoolers.com Wakefield Engineering 33 Bridge St. Pelham, NH 03076 Internet: www.wakefield.com 800-522-6752 603-635-5102 Ultimately, the final selection of an appropriate heat sink depends on many factors, such as thermal performance at a given air velocity, spatial volume, mass, attachment method, assembly, and cost. 19.2.1 Internal Package Conduction Resistance For the exposed-die packaging technology described in Table 71, the intrinsic conduction thermal resistance paths are as follows: * The die junction-to-case thermal resistance (the case is actually the top of the exposed silicon die) * The die junction-to-board thermal resistance MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 116 Freescale Semiconductor Thermal Figure 60 depicts the primary heat transfer path for a package with an attached heat sink mounted to a printed-circuit board. External Resistance Radiation Convection Heat Sink Thermal Interface Material Die/Package Die Junction Package/Leads Internal Resistance Printed-Circuit Board External Resistance Radiation Convection (Note the internal versus external package resistance.) Figure 60. C4 Package with Heat Sink Mounted to a Printed-Circuit Board Heat generated on the active side of the chip is conducted through the silicon, through the heat sink attach material (or thermal interface material), and finally to the heat sink where it is removed by forced-air convection. Because the silicon thermal resistance is quite small, the temperature drop in the silicon may be neglected for a first-order analysis. Thus the thermal interface material and the heat sink conduction/convective thermal resistances are the dominant terms. 19.2.2 Thermal Interface Materials A thermal interface material is recommended at the package-to-heat sink interface to minimize the thermal contact resistance. Figure 61 shows the thermal performance of three thin-sheet thermal-interface materials (silicone, graphite/oil, floroether oil), a bare joint, and a joint with thermal grease as a function of contact pressure. As shown, the performance of these thermal interface materials improves with increasing contact pressure. The use of thermal grease significantly reduces the interface thermal resistance. That is, the bare joint results in a thermal resistance approximately seven times greater than the thermal grease joint. Often, heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit board (see Figure 59). Therefore, synthetic grease offers the best thermal performance, considering the low interface pressure, and is recommended due to the high power dissipation of the MPC8641. Of course, the selection of any thermal interface material depends on many factors--thermal performance requirements, manufacturability, service temperature, dielectric properties, cost, and so on. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 117 Thermal Silicone Sheet (0.006 in.) Bare Joint Fluoroether Oil Sheet (0.007 in.) Graphite/Oil Sheet (0.005 in.) Synthetic Grease Specific Thermal Resistance (K-in.2/W) 2 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 Contact Pressure (psi) Figure 61. Thermal Performance of Select Thermal Interface Material The board designer can choose between several types of thermal interface. Heat sink adhesive materials should be selected based on high conductivity and mechanical strength to meet equipment shock/vibration requirements. There are several commercially available thermal interfaces and adhesive materials provided by the following vendors: The Bergquist Company 800-347-4572 18930 West 78th St. Chanhassen, MN 55317 Internet: www.bergquistcompany.com Chomerics, Inc. 781-935-4850 77 Dragon Ct. Woburn, MA 01801 Internet: www.chomerics.com Dow-Corning Corporation 800-248-2481 Corporate Center PO Box 994 Midland, MI 48686-0994 Internet: www.dowcorning.com MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 118 Freescale Semiconductor Thermal Shin-Etsu MicroSi, Inc. 10028 S. 51st St. Phoenix, AZ 85044 Internet: www.microsi.com Thermagon Inc. 4707 Detroit Ave. Cleveland, OH 44102 Internet: www.thermagon.com 888-642-7674 888-246-9050 The following section provides a heat sink selection example using one of the commercially available heat sinks. 19.2.3 Heat Sink Selection Example For preliminary heat sink sizing, the die-junction temperature can be expressed as follows: Tj = Ti + Tr + (RJC + Rint + Rsa) x Pd where: Tj is the die-junction temperature Ti is the inlet cabinet ambient temperature Tr is the air temperature rise within the computer cabinet RJC is the junction-to-case thermal resistance Rint is the adhesive or interface material thermal resistance Rsa is the heat sink base-to-ambient thermal resistance Pd is the power dissipated by the device During operation, the die-junction temperatures (Tj) should be maintained less than the value specified in Table 2. The temperature of air cooling the component greatly depends on the ambient inlet air temperature and the air temperature rise within the electronic cabinet. An electronic cabinet inlet-air temperature (Ti) may range from 30 to 40C. The air temperature rise within a cabinet (Tr) may be in the range of 5 to 10C. The thermal resistance of the thermal interface material (Rint) is typically about 0.2C/W. For example, assuming a Ti of 30C, a Tr of 5C, a package RJC = 0.1, and a typical power consumption (Pd) of 43.4 W, the following expression for Tj is obtained: Die-junction temperature: Tj = 30C + 5C + (0.1C/W + 0.2C/W + sa) x 43.4 W For this example, a Rsavalue of 1.32 C/W or less is required to maintain the die junction temperature below the maximum value of Table 2. Though the die junction-to-ambient and the heat sink-to-ambient thermal resistances are a common figure-of-merit used for comparing the thermal performance of various microelectronic packaging technologies, one should exercise caution when only using this metric in determining thermal management because no single parameter can adequately describe three-dimensional heat flow. The final die-junction operating temperature is not only a function of the component-level thermal resistance, but the system-level design and its operating conditions. In addition to the component's power consumption, a number of factors affect the final operating die-junction temperature--airflow, board population (local MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 119 Thermal heat flux of adjacent components), heat sink efficiency, heat sink placement, next-level interconnect technology, system air temperature rise, altitude, and so on. Due to the complexity and variety of system-level boundary conditions for today's microelectronic equipment, the combined effects of the heat transfer mechanisms (radiation, convection, and conduction) may vary widely. For these reasons, we recommend using conjugate heat transfer models for the board as well as system-level designs. For system thermal modeling, the MPC8641 thermal model is shown in Figure 62. Four cuboids are used to represent this device. The die is modeled as 12.4x15.3 mm at a thickness of 0.86 mm. See Section 3, "Power Characteristics" for power dissipation details. The substrate is modeled as a single block 33x33x1.2 mm with orthotropic conductivity: 13.5 W/(m * K) in the xy-plane and 5.3 W/(m * K) in the z-direction. The die is centered on the substrate. The bump/underfill layer is modeled as a collapsed thermal resistance between the die and substrate with a conductivity of 5.3 W/(m * K) in the thickness dimension of 0.07 mm. Because the bump/underfill is modeled with zero physical dimension (collapsed height), the die thickness was slightly enlarged to provide the correct height. The C5 solder layer is modeled as a cuboid with dimensions 33x33x0.4 mm and orthotropic thermal conductivity of 0.034 W/(m * K) in the xy-plane and 9.6 W/(m * K) in the z-direction. An LGA solder layer would be modeled as a collapsed thermal resistance with thermal conductivity of 9.6W/(m * K) and an effective height of 0.1 mm. The thermal model uses approximate dimensions to reduce grid. Please refer to the case outline for actual dimensions. Conductivity Value Unit Die Die (12.4x15.3x0.86 mm) Bump and Underfill z Silicon Temperature dependent Substrate C5 solder layer Bump and Underfill (12.4 x 15.3 x 0.07 mm) Collapsed Resistance kz 5.3 Side View of Model (Not to Scale) W/(m * K) x Substrate (33 x 33 x 1.2 mm) kx 13.5 ky 13.5 kz 5.3 W/(m * K) Substrate Die C5 Solder layer (33 x 33 x 0.4 mm) kx 0.034 ky 0.034 kz 9.6 W/(m * K) y Top View of Model (Not to Scale) Figure 62. Recommended Thermal Model of MPC8641 MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 120 Freescale Semiconductor Thermal 19.2.4 Temperature Diode The MPC8641 has a temperature diode on the microprocessor that can be used in conjunction with other system temperature monitoring devices (such as Analog Devices, ADT7461TM). These devices use the negative temperature coefficient of a diode operated at a constant current to determine the temperature of the microprocessor and its environment. For proper operation, the monitoring device used should auto-calibrate the device by canceling out the VBE variation of each MPC8641's internal diode. The following are the specifications of the MPC8641 on-board temperature diode: Vf > 0.40 V Vf < 0.90 V Operating range 2-300 A Diode leakage < 10 nA @ 125C Ideality factor over 5-150 A at 60C: n = 1.0275 0.9% Ideality factor is defined as the deviation from the ideal diode equation: qVf ___ Ifw = Is e nKT - 1 Another useful equation is: KT q I IL H VH - VL = n __ ln __ Where: Ifw = Forward current Is = Saturation current Vd = Voltage at diode Vf = Voltage forward biased VH = Diode voltage while IH is flowing VL = Diode voltage while IL is flowing IH = Larger diode bias current IL = Smaller diode bias current q = Charge of electron (1.6 x 10 -19 C) n = Ideality factor (normally 1.0) K = Boltzman's constant (1.38 x 10-23 Joules/K) T = Temperature (Kelvins) MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 121 System Design Information The ratio of IH to IL is usually selected to be 10:1. The above simplifies to the following: VH - VL = 1.986 x 10-4 x nT Solving for T, the equation becomes: nT = VH - VL __________ 1.986 x 10-4 20 System Design Information This section provides electrical and thermal design recommendations for successful application of the MPC8641. 20.1 System Clocking This device includes six PLLs, as follows: 1. The platform PLL generates the platform clock from the externally supplied SYSCLK input. The frequency ratio between the platform and SYSCLK is selected using the platform PLL ratio configuration bits as described in Section 18.2, "MPX to SYSCLK PLL Ratio." 2. The dual e600 Core PLLs generate the e600 clock from the externally supplied input. 3. The local bus PLL generates the clock for the local bus. 4. There are two internal PLLs for the SerDes block. 20.2 20.2.1 Power Supply Design and Sequencing PLL Power Supply Filtering Each of the PLLs listed above is provided with power through independent power supply pins. There are a number of ways to reliably provide power to the PLLs, but the recommended solution is to provide independent filter circuits per PLL power supply as illustrated in Figure 64, one to each of the AVDD type pins. By providing independent filters to each PLL the opportunity to cause noise injection from one PLL to the other is reduced. This circuit is intended to filter noise in the PLLs resonant frequency range from a 500 kHz to 10 MHz range. It should be built with surface mount capacitors with minimum Effective Series Inductance (ESL). Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a single large value capacitor. Each circuit should be placed as close as possible to the specific AVDD type pin being supplied to minimize noise coupled from nearby circuits. It should be possible to route directly from the capacitors to the AVDD type pin, which is on the periphery of the footprint, without the inductance of vias. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 122 Freescale Semiconductor System Design Information Figure 63 and Figure 64 show the PLL power supply filter circuits for the platform and cores, respectively. 10 VDD_PLAT AVDD_PLAT, AVDD_LB; 2.2 F 2.2 F Low ESL Surface Mount Capacitors GND Figure 63. MPC8641 PLL Power Supply Filter Circuit (for platform and Local Bus) Filter Circuit (should not be used for Single core device) 10 VDD_Core0/1 AVDD_Core0/1 2.2 F 2.2 F GND Low ESL Surface Mount Capacitors Note: For single core device the filter circuit (in the dashed box) should be removed and AVDD_Core1 should be tied to ground with a weak (2-10 k) pull-down resistor. Figure 64. MPC8641 PLL Power Supply Filter Circuit (for cores) The AVDD_SRDSn signals provide power for the analog portions of the SerDes PLL. To ensure stability of the internal clock, the power supplied to the PLL is filtered using a circuit similar to the one shown in following figure. For maximum effectiveness, the filter circuit is placed as closely as possible to the AVDD_SRDSn balls to ensure it filters out as much noise as possible. The ground connection should be near the AVDD_SRDSn balls. The 0.003-F capacitor is closest to the balls, followed by the two 2.2-F capacitors, and finally the 1 resistor to the board supply plane. The capacitors are connected from AVDD_SRDSn to the ground plane. Use ceramic chip capacitors with the highest possible self-resonant frequency. All traces should be kept short, wide and direct. SVDD 1.0 AVDD_SRDSn 2.2 F 1 2.2 F 1 0.003 F GND 1. An 0805 sized capacitor is recommended for system initial bring-up. Figure 65. SerDes PLL Power Supply Filter Note the following: * AVDD_SRDSn should be a filtered version of SVDD. * Signals on the SerDes interface are fed from the SVDD power plan. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 123 System Design Information 20.2.2 PLL Power Supply Sequencing For details on power sequencing for the AVDD type and supplies refer to Section 2.2, "Power Up/Down Sequence." 20.3 Decoupling Recommendations Due to large address and data buses, and high operating frequencies, the device can generate transient power surges and high frequency noise in its power supply, especially while driving large capacitive loads. This noise must be prevented from reaching other components in the MPC8641 system, and the device itself requires a clean, tightly regulated source of power. Therefore, it is recommended that the system designer place at least one decoupling capacitor at each OVDD, Dn_GVDD, LVDD, TVDD, VDD_Coren, and VDD_PLAT pin of the device. These decoupling capacitors should receive their power from separate OVDD, Dn_GVDD, LVDD, TVDD, VDD_Coren, and VDD_PLAT and GND power planes in the PCB, utilizing short traces to minimize inductance. Capacitors may be placed directly under the device using a standard escape pattern. Others may surround the part. These capacitors should have a value of 0.01 or 0.1 F. Only ceramic SMT (surface mount technology) capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes. In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB, feeding the OVDD, Dn_GVDD, LVDD, TVDD, VDD_Coren, and VDD_PLAT planes, to enable quick recharging of the smaller chip capacitors. They should also be connected to the power and ground planes through two vias to minimize inductance. Suggested bulk capacitors--100-330 F (AVX TPS tantalum or Sanyo OSCON). 20.4 SerDes Block Power Supply Decoupling Recommendations The SerDes block requires a clean, tightly regulated source of power (SVDD and XVDD_SRDSn) to ensure low jitter on transmit and reliable recovery of data in the receiver. An appropriate decoupling scheme is outlined below. Only surface mount technology (SMT) capacitors should be used to minimize inductance. Connections from all capacitors to power and ground should be done with multiple vias to further reduce inductance. * First, the board should have at least 10 x 10-nF SMT ceramic chip capacitors as close as possible to the supply balls of the device. Where the board has blind vias, these capacitors should be placed directly below the chip supply and ground connections. Where the board does not have blind vias, these capacitors should be placed in a ring around the device as close to the supply and ground connections as possible. * Second, there should be a 1-F ceramic chip capacitor on each side of the device. This should be done for all SerDes supplies. * Third, between the device and any SerDes voltage regulator there should be a 10-F, low equivalent series resistance (ESR) SMT tantalum chip capacitor and a 100-F, low ESR SMT tantalum chip capacitor. This should be done for all SerDes supplies. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 124 Freescale Semiconductor System Design Information 20.5 Connection Recommendations To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal level. In general all unused active low inputs should be tied to OVDD, Dn_GVDD, LVDD, TVDD, VDD_Coren, and VDD_PLAT, XVDD_SRDSn, and SVDD as required and unused active high inputs should be connected to GND. All NC (no-connect) signals must remain unconnected. Special cases: DDR - If one of the DDR ports is not being used the power supply pins for that port can be connected to ground so that there is no need to connect the individual unused inputs of that port to ground. Note that these power supplies can only be powered up again at reset for functionality to occur on the DDR port. Power supplies for other functional buses should remain powered. Local Bus - If parity is not used, tie LDP[0:3] to ground via a 4.7 k resistor, tie LPBSE to OVDD via a 4.7 k resistor (pull-up resistor). For systems which boot from Local Bus (GPCM)-controlled flash, a pullup on LGPL4 is required. SerDes - Receiver lanes configured for PCI Express are allowed to be disconnected (as would occur when a PCI Express slot is connected but not populated). Directions for terminating the SerDes signals is discussed in Section 20.5.1, "Guidelines for High-Speed Interface Termination." 20.5.1 Guidelines for High-Speed Interface Termination 20.5.1.1 SerDes Interface The high-speed SerDes interface can be disabled through the POR input cfg_io_ports[0:3] and through the DEVDISR register in software. If a SerDes port is disabled through the POR input the user can not enable it through the DEVDISR register in software. However, if a SerDes port is enabled through the POR input the user can disable it through the DEVDISR register in software. Disabling a SerDes port through software should be done on a temporary basis. Power is always required for the SerDes interface, even if the port is disabled through either mechanism. Table 72 describes the possible enabled/disabled scenarios for a SerDes port. The termination recommendations must be followed for each port. Table 72. SerDes Port Enabled/Disabled Configurations Disabled through POR input Enabled through POR input SerDes port is disabled (and cannot be enabled through DEVDISR) SerDes port is enabled Enabled through DEVDISR Complete termination required (Reference Clock not required) SerDes port is disabled (through POR input) Disabled through DEVDISR Complete termination required (Reference Clock not required) Partial termination may be required 1 (Reference Clock is required) SerDes port is disabled after software disables port Same termination requirements as when the port is enabled through POR input 2 (Reference Clock is required) MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 125 System Design Information 1 Partial Termination when a SerDes port is enabled through both POR input and DEVDISR is determined by the SerDes port mode. If the port is in x8 PCI Express mode, no termination is required because all pins are being used. If the port is in x1/x2/x4 PCI Express mode, termination is required on the unused pins. If the port is in x4 Serial RapidIO mode termination is required on the unused pins. 2 If a SerDes port is enabled through the POR input and then disabled through DEVDISR, no hardware changes are required. Termination of the SerDes port should follow what is required when the port is enabled through both POR input and DEVDISR. See Note 1 for more information. If the high-speed SerDes port requires complete or partial termination, the unused pins should be terminated as described in this section. The following pins must be left unconnected (floating): * SDn_TX[7:0] * SDn_TX[7:0] The following pins must be connected to GND: * SDn_RX[7:0] * SDn_RX[7:0] * SDn_REF_CLK * SDn_REF_CLK NOTE It is recommended to power down the unused lane through SRDS1CR1[0:7] register (offset = 0xE_0F08) and SRDS2CR1[0:7] register (offset = 0xE_0F44.) (This prevents the oscillations and holds the receiver output in a fixed state.) that maps to SERDES lane 0 to lane 7 accordingly. For other directions on reserved or no-connects pins see Section 17, "Signal Listings." 20.6 Pull-Up and Pull-Down Resistor Requirements The MPC8641 requires weak pull-up resistors (2-10 k is recommended) on all open drain type pins. The following pins must NOT be pulled down during power-on reset: TSEC4_TXD[4], LGPL0/LSDA10, LGPL1/LSDWE, TRIG_OUT/READY, and D1_MSRCID[2]. The following are factory test pins and require strong pull up resistors (100 -1 k) to OVDD LSSD_MODE, TEST_MODE[0:3].The following pins require weak pull up resistors (2-10 k) to their specific power supplies: LCS[0:4], LCS[5]/DMA_DREQ2, LCS[6]/DMA_DACK[2], LCS[7]/DMA_DDONE[2], IRQ_OUT, IIC1_SDA, IIC1_SCL, IIC2_SDA, IIC2_SCL, and CKSTP_OUT. The following pins should be pulled to ground with a 100- resistor: SD1_IMP_CAL_TX, SD2_IMP_CAL_TX. The following pins should be pulled to ground with a 200- resistor: SD1_IMP_CAL_RX, SD2_IMP_CAL_RX. TSECn_TX_EN signals require an external 4.7-k pull down resistor to prevent PHY from seeing a valid Transmit Enable before it is actively driven. When the platform frequency is 400 MHz, TSEC1_TXD[1] must be pulled down at reset. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 126 Freescale Semiconductor System Design Information TSEC2_TXD[4] and TSEC2_TX_ER pins function as cfg_dram_type[0 or 1] at reset and MUST BE VALID BEFORE HRESET ASSERTION when coming out of device sleep mode. 20.6.1 Special instructions for Single Core device The mechanical drawing for the single core device does not have all the solder balls that exist on the single core device. This includes all the balls for VDD_Core1 and SENSEVDD_Core1 which exist on the package for the dual core device, but not on the single core package. A solder ball is present for SENSEVSS_Core1 and needs to be connected to ground with a weak (2-10 k) pull down resistor. Likewise, AVDD_Core1 needs to be pulled to ground as shown in Figure 64. The mechanical drawing for the single core device is located in Section 16.2, "Mechanical Dimensions of the MPC8641 FC-CBGA." For other pin pull-up or pull-down recommendations of signals, please see Section 17, "Signal Listings." 20.7 Output Buffer DC Impedance The MPC8641 drivers are characterized over process, voltage, and temperature. For all buses, the driver is a push-pull single-ended driver type (open drain for I2C). To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to OVDD or GND. Then, the value of each resistor is varied until the pad voltage is OVDD/2 (see Figure 66). The output impedance is the average of two components, the resistances of the pull-up and pull-down devices. When data is held high, SW1 is closed (SW2 is open) and RP is trimmed until the voltage at the pad equals OVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each other in value. Then, Z0 = (RP + RN)/2. OV DD RN SW2 Data Pad SW1 RP OGND Figure 66. Driver Impedance Measurement MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 127 System Design Information Table 73 summarizes the signal impedance targets. The driver impedances are targeted at minimum VDD, nominal OVDD, 105C. Table 73. Impedance Characteristics Impedance DUART, Control, Configuration, Power Management PCI Express DDR DRAM Symbol Unit RN 43 Target 25 Target 20 Target Z0 W RP 43 Target 25 Target 20 Target Z0 W Note: Nominal supply voltages. See Table 1, Tj = 105C. 20.8 Configuration Pin Muxing The MPC8641 provides the user with power-on configuration options which can be set through the use of external pull-up or pull-down resistors of 4.7 k on certain output pins (see customer visible configuration pins). These pins are generally used as output only pins in normal operation. While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins while HRESET is asserted, is latched when HRESET deasserts, at which time the input receiver is disabled and the I/O circuit takes on its normal function. Most of these sampled configuration pins are equipped with an on-chip gated resistor of approximately 20 k. This value should permit the 4.7-k resistor to pull the configuration pin to a valid logic low level. The pull-up resistor is enabled only during HRESET (and for platform /system clocks after HRESET deassertion to ensure capture of the reset value). When the input receiver is disabled the pull-up is also, thus allowing functional operation of the pin as an output with minimal signal quality or delay disruption. The default value for all configuration bits treated this way has been encoded such that a high voltage level puts the device into the default state and external resistors are needed only when non-default settings are required by the user. Careful board layout with stubless connections to these pull-down resistors coupled with the large value of the pull-down resistor should minimize the disruption of signal quality or speed for output pins thus configured. The platform PLL ratio and e600 PLL ratio configuration pins are not equipped with these default pull-up devices. 20.9 JTAG Configuration Signals Correct operation of the JTAG interface requires configuration of a group of system control pins as demonstrated in Figure 68. Care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions as most have asynchronous behavior and spurious assertion will give unpredictable results. Boundary-scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the IEEE 1149.1 specification, but is provided on all processors that implement the Power Architecture technology. The device requires TRST to be asserted during reset conditions to ensure the JTAG boundary logic does not interfere with normal chip operation. While it is possible to force the TAP controller to the reset state using only the TCK and TMS signals, more reliable power-on reset performance will be obtained MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 128 Freescale Semiconductor System Design Information if the TRST signal is asserted during power-on reset. Because the JTAG interface is also used for accessing the common on-chip processor (COP) function, simply tying TRST to HRESET is not practical. The COP function of these processors allows a remote computer system (typically a PC with dedicated hardware and debugging software) to access and control the internal operations of the processor. The COP port connects primarily through the JTAG interface of the processor, with some additional status monitoring signals. The COP port requires the ability to independently assert HRESET or TRST in order to fully control the processor. If the target system has independent reset sources, such as voltage monitors, watchdog timers, power supply failures, or push-button switches, then the COP reset signals must be merged into these signals with logic. The arrangement shown in Figure 67 allows the COP port to independently assert HRESET or TRST, while ensuring that the target can drive HRESET as well. The COP interface has a standard header, shown in Figure 67, for connection to the target system, and is based on the 0.025" square-post, 0.100" centered header assembly (often called a Berg header). The connector typically has pin 14 removed as a connector key. The COP header adds many benefits such as breakpoints, watchpoints, register and memory examination/modification, and other standard debugger features. An inexpensive option can be to leave the COP header unpopulated until needed. There is no standardized way to number the COP header shown in Figure 67; consequently, many different pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended in Figure 67 is common to all known emulators. For a multi-processor non-daisy chain configuration, Figure 68, can be duplicated for each processor. The recommended daisy chain configuration is shown in Figure 69. Please consult with your tool vendor to determine which configuration is supported by their emulator. 20.9.1 Termination of Unused Signals If the JTAG interface and COP header will not be used, Freescale recommends the following connections: * TRST should be tied to HRESET through a 0 k isolation resistor so that it is asserted when the system reset signal (HRESET) is asserted, ensuring that the JTAG scan chain is initialized during the power-on reset flow. Freescale recommends that the COP header be designed into the system as shown in Figure 68. If this is not possible, the isolation resistor will allow future access to TRST in case a JTAG interface may need to be wired onto the system in future debug situations. * Tie TCK to OVDD through a 10 k resistor. This will prevent TCK from changing state and reading incorrect data into the device. * No connection is required for TDI, TMS, or TDO. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 129 System Design Information COP_TDO 1 2 NC COP_TDI 3 4 COP_TRST NC 5 6 COP_VDD_SENSE COP_TCK 7 8 COP_CHKSTP_IN COP_TMS 9 10 NC COP_SRESET 11 12 NC COP_HRESET 13 KEY No pin COP_CHKSTP_OUT 15 16 GND Figure 67. COP Connector Physical Pinout MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 130 Freescale Semiconductor System Design Information OVDD SRESET0 From Target Board Sources (if any) SRESET1 HRESET 13 11 10 k SRESET0 10 k SRESET1 10 k HRESET1 COP_HRESET 10 k COP_SRESET 10 k 5 1 2 10 k 4 4 5 6 6 7 8 5 9 10 COP Header 3 11 12 KEY 13 No pin 15 10 k 15 COP_TRST COP_VDD_SENSE2 TRST1 10 NC COP_CHKSTP_OUT CKSTP_OUT 10 k 14 3 10 k COP_CHKSTP_IN CKSTP_IN 8 COP_TMS 16 TMS 9 COP Connector Physical Pinout 1 3 COP_TDO TDO COP_TDI TDI COP_TCK 7 TCK 2 NC 10 NC 12 4 10 k 16 Notes: 1. The COP port and target board should be able to independently assert HRESET and TRST to the processor in order to fully control the processor as shown here. 2. Populate this with a 10 resistor for short-circuit/current-limiting protection. 3. The KEY location (pin 14) is not physically present on the COP header. 4. Although pin 12 is defined as a No-Connect, some debug tools may use pin 12 as an additional GND pin for improved signal integrity. 5. This switch is included as a precaution for BSDL testing. The switch should be open during BSDL testing to avoid accidentally asserting the TRST line. If BSDL testing is not being performed, this switch should be closed or removed. Figure 68. JTAG/COP Interface Connection for one MPC8641 device MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 131 Ordering Information OVDD 10k 10k TDI MPC8641 SRESET0 10k SRESET0 From Target Board Sources (if any) SRESET1 SRESET1 3 HRESET HRESET 4 OVDD 10k 10k 3 10k COP_TDI COP_SRESET COP_HRESET COP_CHKSTP_IN 2 COP_TMS COP_TCK GND 10k 10k 13 CHKSTP_OUT CHKSTP_IN TMS TCK 3 TDO NC 15 8 2 10 JTAG/COP Header 10k TRST 4 5 11 4 COP_TRST 5 COP_CHKSTP_OUT 10k 14 TDI MPC8641 SRESET0 SRESET1 HRESET 4 NC NC 9 TRST 4 7 12 16 CHKSTP_OUT CHKSTP_IN TMS TCK 6 10 1 6 COP_VDD_SENSE TDO COP_TDO 1 Notes: 1. Populate this with a 10 resistor for short circuit/current-limiting protection. 2. KEY location; pin 14 is not physically present on the COP header. 3. Use a AND gate with sufficient drive strength to drive two inputs. 4. The COP port and target board should be able to independently assert HRESET and TRST to the processor in order to fully control the processor as shown above. 5. This switch is included as a precaution for BSDL testing. The switch should be open during BSDL testing to avoid accidentally asserting the TRST line. If BSDL testing is not being performed, this switch should be closed or removed. 6. Although pin 12 is defined as a No-Connect, some debug tools may use pin 12 as an additional GND pin for improved signal integrity. Figure 69. JTAG/COP Interface Connection for Multiple MPC8641 Devices in Daisy Chain Configuration 21 Ordering Information Ordering information for the parts fully covered by this specification document is provided in Section 21.1, "Part Numbers Fully Addressed by This Document." MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 132 Freescale Semiconductor Ordering Information 21.1 Part Numbers Fully Addressed by This Document Table 74 provides the Freescale part numbering nomenclature for the MPC8641. Note that the individual part numbers correspond to a maximum processor core frequency. For available frequencies, contact your local Freescale sales office. In addition to the processor frequency, the part numbering scheme also includes an application modifier which may specify special application conditions. Each part number also contains a revision code which refers to the die mask revision number. Table 74. Part Numbering Nomenclature MC nnnn Product Part Code Identifier x xx nnnn x x Core Count Package 1 Core Processor Frequency 2 (MHz) DDR speed (MHz) Product Revision Level Blank = Single Core MC 8641 D = Dual Core N = 500 MHz4 HX = High-lead HCTE FC-CBGA VU = RoHS lead-free HCTE FC-CBGA K = 600 MHz 1000, 1250, 1333, 1500 J = 533 MHz H = 500 MHz G = 400 MHz Revision B = 2.0 System Version Register Value for Rev B: 0x8090_0020 - MPC8641 0x8090_0120 - MPC8641D Revision C = 2.1 System Version Register Value for Rev C: 0x8090_0021 - MPC8641 0x8090_0121 - MPC8641D Notes: 1. See Section 16, "Package," for more information on available package types. 2. Processor core frequencies supported by parts addressed by this specification only. Not all parts described in this specification support all core frequencies. Additionally, parts addressed by part number specifications may support other maximum core frequencies. Note that core processor speed of 1500 MHz is only available for the MPC8641D (dual core). 3. The P prefix in a Freescale part number designates a "Pilot Production Prototype" as defined by Freescale SOP 3-13. These parts have only preliminary reliability and characterization data. Before pilot production prototypes may be shipped, written authorization from the customer must be on file in the applicable sales office acknowledging the qualification status and the fact that product changes may still occur while shipping pilot production prototypes. 4. Part Number MC8641xxx1000NX is our low VDD_Coren device. VDD_Coren = 0.95 V and VDD_PLAT = 1.05 V. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 133 Ordering Information Table 75 shows the parts that are available for ordering and their operating conditions. Table 75. Part Offerings and Operating Conditions Part Offerings 1 1 Operating Conditions MC8641Dxx1500KX Dual core Max CPU speed = 1500 MHz, Max DDR = 600 MHz Core Voltage = 1.1 volts MC8641Dxx1333JX Dual core Max CPU speed = 1333 MHz, Max DDR = 533 MHz Core Voltage = 1.05 volts MC8641Dxx1250HX Dual core Max CPU speed = 1250 MHz, Max DDR = 500 MHz Core Voltage = 1.05 volts MC8641Dxx1000GX Dual core Max CPU speed = 1000 MHz, Max DDR = 400 MHz Core Voltage = 1.05 volts MC8641Dxx1000NX Dual core MAX CPU speed = 1000 MHz, MAX DDR = 500 MHz Core Voltage = 0.95 volts MC8641xx1500KX Single core Max CPU speed = 1500 MHz, Max DDR = 600 MHz Core Voltage = 1.1 volts MC8641xx1333JX Single core Max CPU speed = 1333 MHz, Max DDR = 533 MHz Core Voltage = 1.05 volts MC8641xx1250HX Single core Max CPU speed = 1250 MHz, Max DDR = 500 MHz Core Voltage = 1.05 volts MC8641xx1000HX Single core Max CPU speed = 1000 MHz, Max DDR = 400 MHz Core Voltage = 1.05 volts MC8641xx1000NX Single core Max CPU speed = 1000 MHz, Max DDR = 500 MHz Core Voltage = 0.95 volts Note that the xx in the part marking represents the package option. The upper case "X" represents the revision letter. For more information see Table 74. MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 134 Freescale Semiconductor Ordering Information 21.2 Part Marking Parts are marked as the example shown in Figure 70. MC8641x xxnnnnxx TWLYYWW MMMMMM YWWLAZ 8641D NOTE: TWLYYWW is the test code MMMMMM is the M00 (mask) number. YWWLAZ is the assembly traceability code. Figure 70. Part Marking for FC-CBGA Device MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 135 Document Revision History 22 Document Revision History Table 76 provides a revision history for the MPC8641D hardware specification. Table 76. Document Revision History Revision Date 0 07/2008 Substantive Change(s) * Initial Release MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 136 Freescale Semiconductor Document Revision History THIS PAGE INTENTIONALLY LEFT BLANK MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 137 Document Revision History THIS PAGE INTENTIONALLY LEFT BLANK MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 138 Freescale Semiconductor Document Revision History THIS PAGE INTENTIONALLY LEFT BLANK MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 0 Freescale Semiconductor 139 How to Reach Us: Home Page: www.freescale.com email: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 1-800-521-6274 480-768-2130 support@freescale.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Freescale Semiconductor reserves the right to make changes without further notice to Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku Tokyo 153-0064, Japan 0120 191014 +81 3 5437 9125 support.japan@freescale.com parameters, including "Typicals" must be validated for each customer application by Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate, Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor @hibbertgroup.com FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. All other product or service names are the property of their respective owners. Document Number: MPC8641DEC Rev. 0 7/2008 any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. (c) Freescale Semiconductor, Inc., 2008.