TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 D Maximum Throughput . . . 175/360 KSPS D INL/DNL: 1 LSB Max, SINAD: 72 dB, D D D D SFDR: 85 dB, fi = 20 kHz SPI/DSP-Compatible Serial Interface Single 5-V Supply Rail-to-Rail Analog Input With 500 kHz BW Three Options Available: - TLC2551: Single Channel Input TOP VIEW TLC2551 CS VREF GND AIN D D - TLC2552: Dual Channels With Autosweep - TLC2555: Single Channel With Pseudo-Differential Input Low Power With Autopower Down - Operating Current: 3.5 mA Autopower Down: 8 A Small 8-Pin MSOP and SOIC Packages TOP VIEW TLC2552 1 8 2 7 3 6 4 5 SDO FS VDD SCLK CS VREF GND AIN0 TOP VIEW TLC2555 1 8 2 7 3 6 4 5 SDO SCLK VDD AIN1 CS VREF GND AIN(+) 1 8 2 7 3 6 4 5 SDO SCLK VDD AIN(-) description The TLC2551, TLC2552, and TLC2555 are a family of high performance, 12-bit, low-power, miniature, CMOS analog-to-digital converters (ADC). The TLC255x family uses a 5-V supply. Devices are available with single, dual, or single pseudo-differential inputs. Each device has a chip select (CS), serial clock (SCLK), and serial data output (SDO) that provides a direct 3-wire interface to the serial port of most popular host microprocessors (SPI interface). When interfaced with a TMS320 DSP, a frame sync signal (FS) can be used to indicate the start of a serial data frame on CS for all devices or on FS for the TLC2551. The TLC2551, TLC2552, and TLC2555 are designed to operate with very low power consumption. The power saving feature is further enhanced with an autopower-down mode. This product family features a high-speed serial link to modern host processors with SCLK up to 20 MHz. The maximum SCLK frequency is dependent upon the mode of operation (see Table 1). The TLC255x family uses SCLK as the conversion clock, which provides synchronous operation and a minimum conversion time of 1.5 s using a 20-MHz SCLK. AVAILABLE OPTIONS PACKAGED DEVICES TA 8-MSOP (DGK) 8-SOIC (D) TLC2551CDGK (AHF) 0C 70C 0 C to 70 C TLC2552CDGK (AHH) TLC2555CDGK (AHJ) - 40C 40 C to 85C 85 C TLC2551IDGK (AHG) TLC2551ID TLC2552IDGK (AHI) TLC2552ID TLC2555IDGK (AHK) TLC2555ID Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. TMS320 is a trademark of Texas Instruments. Copyright 2002 - 2003, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 functional block diagram TLC2551 TLC2552 VDD VDD VREF VREF AIN0 AIN S/H LOW POWER 12-BIT SAR ADC Mux AIN1 SDO S/H LOW POWER SAR ADC /2 SCLK CS FS /2 CONTROL LOGIC SCLK CS GND CONTROL LOGIC GND TLC2555 VDD VREF AIN (+) S/H AIN (-) LOW POWER 12-BIT SAR ADC /2 SCLK CS CONTROL LOGIC GND 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SDO SDO TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 Terminal Functions TLC2551 TERMINAL NAME NO. I/O DESCRIPTION AIN 4 I Analog input channel CS 1 I Chip select. A high-to-low transition on the CS input removes SDO from 3-state within a maximum setup time. CS can be used as the FS pin when a dedicated DSP serial port is used. FS 7 I DSP frame sync input. Indication of the start of a serial data frame. Tie this terminal to VDD if not used. GND 3 I Ground return for the internal circuitry. Unless otherwise noted, all voltage measurements are with respect to GND. SCLK 5 I Output serial clock. This terminal receives the serial SCLK from the host processor. SDO 8 O The 3-state serial output for the A/D conversion result. SDO is kept in the high-impedance state until CS falling edge or FS rising edge, whichever occurs first. The output format is MSB first. When FS is not used (FS = 1 at the falling edge of CS), the MSB is presented to the SDO pin after CS falling edge and output data is valid on the first falling edge of SCLK. When CS and FS are both used (FS = 0 at the falling edge of CS), the MSB is presented to the SDO pin after the falling edge of CS. When CS is tied/held low, the MSB is presented on SDO after rising FS. Output data is valid on the first falling edge of SCLK. (This is typically used with an active FS from a DSP.) VDD VREF 6 I Positive supply voltage 2 I External reference input TLC2552/55 TERMINAL I/O DESCRIPTION NAME NO. AIN0 /AIN(+) 4 I Analog input channel 0 for TLC2552--Positive input for TLC2555 AIN1/AIN (-) 5 I Analog input channel 1 for TLC2552--Inverted input for TLC2555 CS 1 I Chip select. A high-to-low transition on CS removes SDO from 3-state within a maximum delay time. This pin can be connected to the FS output from a DSP on a dedicated serial port. GND 3 I Ground return for the internal circuitry. Unless otherwise noted, all voltage measurements are with respect to GND. SCLK 7 I Output serial clock. This terminal receives the serial SCLK from the host processor. SDO 8 O The 3-state serial output for the A/D conversion result. SDO is kept in the high-impedance state when CS is high and presents output data after the CS falling edge until the LSB is presented. The output format is MSB first. SDO returns to the Hi-Z state after the 16th SCLK. Output data is valid on the falling SCLK edge. VDD VREF 6 I Positive supply voltage 2 I External reference input detailed description The TLC2551, TLC2552, and TLC2555 are successive approximation (SAR) ADCs utilizing a charge redistribution DAC. Figure 1 shows a simplified version of the ADC. The sampling capacitor acquires the signal on AIN during the sampling period. When the conversion process starts, the SAR control logic and charge redistribution DAC are used to add and subtract fixed amounts of charge from the sampling capacitor to bring the comparator into a balanced condition. When the comparator is balanced, the conversion is complete and the ADC output code is generated. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 detailed description (continued) Charge Redistribution DAC _ AIN Control Logic + ADC Code GND/AIN(-) Figure 1. Simplified SAR Circuit serial interface OUTPUT DATA FORMAT MSB LSB D15-D4 Conversion result (OD11-OD0) D3-D0 Don't care The output data format is binary (unipolar straight binary). binary Zero-scale code = 000h, Vcode = GND Full-scale code = FFFh, Vcode = VREF - 1 LSB pseudo-differential inputs The TLC2555 operates in pseudo-differential mode. The inverted input is available on pin 5. It can have a maximum input ripple of 0.2 V. This is normally used for ground noise rejection. control and timing start of the cycle Each cycle may be started by either CS, FS, or a combination of both. The internal state machine requires one SCLK high-to-low transition to determine the state of these control signals so internal blocks can be powered up in an active cycle. Special care to SPI mode is necessary. Make sure there is at least one SCLK whenever CS (pin 1) is high to assure proper operation. TLC2551 D Control via CS ( FS = 1 at the falling edge of CS)--The falling edge of CS is the start of the cycle. The MSB may be read on the first falling SCLK edge after CS is low. Output data changes on the rising edge of SCLK. This is typically used for a microcontroller with an SPI interface, although it can also be used for a DSP. The microcontroller SPI interface may be programmed for CPOL = 0 (serial clock referenced to ground) and CPHA = 1 (data is valid on the falling edge of serial clock). At least one falling edge transition on SCLK is needed whenever CS is brought high. D Control via FS--The MSB is presented after the rising edge of FS. The falling edge of FS starts the cycle. The MSB may be read on the first falling edge of SCLK after FS is low. This is the typical configuration when the ADC is the only device on the DSP serial port. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 control and timing (continued) D Control via both CS and FS--The MSB is presented after the falling edge of CS. The falling edge of FS starts the sampling cycle. The MSB may be read on the first falling SCLK edge after FS is low. Output data changes on the rising edge of SCLK. This control via CS and FS is typically used for multiple devices connected to a TMS320 DSP. TLC2552 and TLC2555 All control is provided using CS (pin 1) on the TLC2552 and TLC2555. The cycle starts on the falling edge transition provided by either a CS signal from an SPI microcontroller or FS signal from a TMS320 DSP. Timing is similar to the TLC2551, with control via CS only. TLC2552 channel MUX reset cycle The TLC2552 uses CS to reset the analog input multiplexer (MUX). A short active CS cycle (4 to 7 SCLKs) resets the MUX to AIN0. When the CS cycle time is greater than 7 SCLKs in duration, as is the case for a complete conversion cycle, (CS is low for 16 SCLKs plus maximum conversion time), the MUX toggles to the next channel (see Figure 4 for timing). sampling The converter sample time is 12 SCLKs in duration, beginning on the fifth SCLK received after the converter has received a high-to-low CS transition (or a high-to-low FS transition for the TLC2551). conversion The TLC2551, TLC2552, and TLC2555 completes conversion in the following manner. The conversion starts after the 16th SCLK falling edge during the cycle and requires 28 SCLKs to complete. Enough time for conversion should be allowed before a rising CS or FS edge so that no conversion is terminated prematurely. TLC2552 input channel selection is toggled on each rising CS edge. The MUX channel can be reset to AIN0 via CS as described earlier and in Figure 4. The input is sampled for 12 SCLKs and converted. The result is presented on SDO during the next cycle. Care should also be taken to allow enough time between samples to avoid prematurely terminating the cycle, which occurs on a rising CS transition if the conversion is not complete. The SDO data presented during a cycle is the result of the conversion of the sample taken during the previous cycle. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 timing diagrams/conversion cycles 1 2 3 4 5 6 7 12 13 14 15 16 1 44 SCLK CS FS IIIIIIIIIIIIIII IIIIIIIIIIIIIII t(sample) SDO OD11 OD10 OD9 OD8 OD7 OD6 OD5 t(powerdown) tc OD0 Figure 2. TLC2551 Timing: Control via CS (FS = 1) 1 2 3 4 5 6 12 13 14 15 16 1 44 SCLK CS FS IIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII t(sample) SDO OD11 OD10 OD9 OD8 OD7 OD6 t(powerdown) tc OD0 Figure 3. TLC2551 Timing: Control via CS and FS or FS Only 1 2 3 4 5 1 4 12 16 44 1 4 12 16 SCLK >8 SCLKs, MUX Toggles to AIN1 <8 SCLKs, MUX Resets to AIN0 CS t(powerdown) t(sample) t(sample) IIIIII IIIIIII SDO tc AIN0 Result OD11 III tc OD0 Figure 4. TLC2552 Reset Timing 1 2 3 4 5 6 7 12 13 14 15 16 44 1 SCLK CS t(sample) SDO OD11 OD10 OD9 OD8 OD7 OD6 OD5 IIIIII OD0 Figure 5. TLC2552 and TLC2555 Timing 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 tc t(powerdown) OD11 OD10 OD9 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 using CS as the FS input When interfacing the TLC2551 with the TMS320 DSP, the FSR signal from the DSP may be connected to the CS input if this is the only device on the serial port. This connection saves one output terminal from the DSP. (Output data changes on the falling edge of SCLK. This is the default configuration for the TLC2552 and TLC2555). SCLK and conversion speed The SCLK input can range in frequency from 100 kHz to 20 MHz. The required number of conversion clocks is 14. The conversion clock for the ADC is SCLK/2 which translates to 28 SCLK cycles to perform a conversion. For a 15-MHz SCLK, the minimum total cycle time is given by: 16x(1/15 M)+14x(1/7.5 M)+1 SCLK = 3.0 s. An additional SCLK is added to account for the required CS or FS high time. These times specify the minimum cycle time for an active CS or FS signal. If violated, the conversion terminates, invalidating the next data output cycle. Table 1 gives the maximum SCLK frequency for a given operational mode. control via pin 1 (CS, SPI interface) All devices are compatible with this mode of operation. A falling CS initiates the cycle. (For TLC2551, the FS input is tied to VDD.) CS remains low for the entire cycle time (sample + convert + 1 SCLK) and can then be released. NOTE: IMPORTANT: A single SCLK is required whenever CS is high. control via pin 1 (CS, DSP interface) All devices are compatible with this mode of operation. The FS signal from a DSP is connected directly to the CS input of the ADC. A falling edge on the CS input initiates the cycle. (For TLC2551, the FS input can be tied to VDD, although better performance can be achieved by using the FS input for control. Refer to the control via pin 1 and pin 7 (CS and FS or FS only, DSP interface) section. The CS input should remain low for the entire cycle time (sample + convert + 1 SCLK) and can then be released. NOTE: IMPORTANT: A single SCLK is required whenever CS is high. This requirement is usually of little consequence since SCLK is normally always present when interfacing with a DSP. control via pin 1 and pin 7 (CS and FS or FS only, DSP interface) Only the TLC2551 is compatible with this mode of operation. The CS input to the ADC can be controlled via a general-purpose I/O pin from the DSP. The FS signal from the DSP is connected directly to the FS input of the ADC. A falling edge on CS, if used, releases the MSB on the SDO output. When CS is not used, the rising FS edge releases the MSB. The falling edge on the FS input while SCLK is high initiates the cycle. The CS and FS inputs should remain low for the entire cycle time (sample + convert + 1 SCLK) and can then be released. reference voltage An external reference is applied via VREF. The voltage level applied to this pin establishes the upper limit of the analog inputs to produce a full-scale reading. The value of VREF and the analog input must not exceed the positive supply or be less than GND, consistent with the specified absolute maximum ratings. The digital output is at full scale when the input signal is equal to or higher than VREF and at zero when the input signal is equal to or lower than GND. powerdown and powerup Autopower down is built into these devices in order to reduce power consumption. The actual power savings depends on the inactive time between cycles and the power supply (loading) decoupling/storage capacitors. Power-down takes effect immediately after the conversion is complete. This is fast enough to provide some power savings between cycles with longer than 1 SCLK inactive time. The device power goes down to 8 A within 0.5 s. To achieve the lowest power-down current (deep powerdown) of 1 A requires 2-ms inactive time between cycles. The power-down state is initiated at the end of conversion. These devices wake up immediately at the next falling edge of CS or the rising edge of FS. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 ICC With 1-F/0.1-F Capacitor Between Supply and Ground 0.5 S VDD = 5 V 2 mS 3.5 mA 8 A 1 A t(Powerdown) - Powerdown time - S Table 1. Modes of Operation and Data Throughput CONTROL PIN(s)/DEVICE CS control only (TLC2551 only) For SPI DSP interface MAX SCLK (MHz) (50/50 duty cycle) VDD = 4.5 V APPROXIMATE CONVERSION THROUGHPUT (ksps) VDD = 4.5 V 15 333 8 175 20 400 CS and FS control (TLC2551 only) DSP interface See Figure 21(a). See Figure 21(b). See Figure 21(c). absolute maximum ratings over operating free-air temperature (unless otherwise noted) Supply voltage range, GND to VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 6.5 V Analog input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to VDD + 0.3 V Reference input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDD + 0.3 V Digital input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to VDD+ 0.3 V Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 150C Operating free-air temperature range, TA: C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40C to 85C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 recommended operating conditions Supply voltage, VDD MIN NOM MAX 4.5 5 5.5 V VDD VDD V Positive external reference voltage input, VREFP (see Note 1) 2 Analog input voltage (see Note 1) 0 High level control input voltage, VIH 2.1 0.6 VDD = REF = 4.5 V 40 0.5 Setup time, FS rising edge before SCLK falling edge, tsu(FSH-SCLKL) (TLC2551 only) 0.35 V ns 5 Delay time, delay from CS falling edge to FS rising edge td(CSL-FSH) (TLC2551 only) V V Low-level control input voltage, VIL Setup time, CS falling edge before first SCLK falling edge, tsu(CSL-SCLKL) Hold time, CS falling edge after SCLK falling edge, th(SCLKL-CSL) UNIT ns 7 SCLKs SCLKs Hold time, FS hold high after SCLK falling edge, th(SCLKL-FSL) (TLC2551 only) 0.65 SCLKs Pulse width CS high time, tw(H_CS) 100 ns Pulse width FS high time, tw(H_FS) (TLC2551 only) 0.75 SCLKs SCLK cycle time, VDD = 5.5 V to 4.5 V, tc(SCLK) (maximum tolerance of 40/60 duty cycle) 50 10000 Pulse width low time, tw(L_SCLK) 0.4 0.6 SCLKs Pulse width high time, tw(H_SCLK) 0.4 0.6 SCLKs Hold time, hold from end of conversion to CS high, th(EOC-CSH) (EOC is internal, indicates end of conversion time, tc) Active CS cycle time to reset internal MUX to AIN0, t(Reset cycle) (TLC2552 only) s 0.05 4 ns 7 SCLKs Delay time, delay from CS falling edge to SDO valid, td(CSL-SDOV) VDD = REF = 4.5 V, 25-pF load 40 ns Delay time, delay from FS falling edge to SDO valid, td(FSL-SDOV) (TLC2551 only) VDD = REF = 4.5 V, 25-pF load 1 ns VDD = REF = 4.5 V, 25-pF load 11 ns VDD = REF = 4.5 V, 25-pF load 30 ns Delay time, delay from SCLK rising edge to SDO valid, td(SCLKH-SDOV) Delay time, delay from 17th SCLK rising edge to SDO 3-state, td(SCLK17H-SDOZ) Conversion time, tc Sampling time, t(sample) 28 See Note 2 TLC2551/2/5C Operating free free-air air temperature temperature, TA TLC2551/2/5I SCLKs 300 ns 0 70 -40 85 C NOTES: 1. Analog input voltages greater than that applied to VREF convert as all ones (111111111111), while input voltages less than that applied to GND convert as all zeros(000000000000). 2. Minimal t(sample) is given by 0.9 x 50 pF x (RS + 0.5 k), where RS is the source output impedance. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 electrical characteristics over recommended operating free-air temperature range, VDD = VREF = 4.5 V to 5.5 V, (unless otherwise noted) PARAMETER VOH VOL TEST CONDITIONS High-level output voltage Low-level output voltage VDD = 5.5 V, IOH = -0.2 mA at 30-pF load VDD = 5.5 V, IOL = 0.8 mA at 30-pF load IOZ output Off-state out ut current (high-impedance-state) VO = VDD VO = 0 IIH High-level input current 2.5 A -0.00 5 2.5 A 3 3.5 mA CS = VDD VDD = 4.5 V to 5.5 V 10 A A 1 Selected channel at VDD Selected channel at 0 V Control Inputs VDD = 5.5 V POST OFFICE BOX 655303 1 -1 20 45 50 5 25 500 * DALLAS, TEXAS 75265 A A 8 For all digital inputs, 0 VI 0 0.3 0.3 V, 3 V or VI VDD- 0 3V SCLK = 0, VDD = 4.5 V to 5.5 V, Ext ref Analog inputs Input on resistance All typical values are at VDD = 5 V, TA = 25C. V 0.005 CS at 0 V, Input capacitance 0.4 VI = VDD Operating supply current Ci V -2.5 ICC Selected analog input in ut channel leakage current UNIT -1 VI = 0 V Deep autopower-down current t(powerdown) 2 ms MAX 2.4 2.5 Low-level input current ICC(AUTOPWDN) TYP 1 IIL Autopower-down current t(powerdown) 0.5 s MIN A A pF TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 ac specifications (fi = 20 kHz) PARAMETER SINAD Signal-to-noise ratio + distortion THD Total harmonic distortion ENOB Effective number of bits SFDR Spurious free dynamic range TEST CONDITIONS 400 KSPS, VDD = VREF = 5 V 400 KSPS, VDD = VREF = 5 V MIN TYP 70 72 -84 400 KSPS, VDD = VREF = 5 V 400 KSPS, VDD = VREF = 5 V MAX dB -80 11.8 -84 UNIT dB bits -80 dB Analog Input Full-power bandwidth, -3 dB 1 MHz Full-power bandwidth, -1 dB 500 kHz external reference specifications PARAMETER Reference input voltage VREF TEST CONDITIONS VDD = 4.5 V to 5.5 V Reference input impedance VDD = 5.5 55V Reference current VDD = VREF = 5.5 V Reference input capacitance VDD = VREF = 5.5 55V Reference voltage VDD = 4.5 V to 5.5 V MIN TYP 2 CS = 1, SCLK = 0 CS = 0, SCLK = 20 MHz VDD 100 20 SCLK = 0 CS = 0, SCLK = 20 MHz 25 5 20 UNIT V M 100 CS = 1, MAX k 400 A 15 45 50 VDD pF V dc specification, VDD = VREF = 4.5 V to 5.5 V, SCLK frequency = 20 MHz (unless otherwise noted) PARAMETER INL Integral linearity error (see Note 4) DNL Differential linearity error TEST CONDITIONS Offset error (see Note 5) See Note 3 EG Gain error (see Note 5) See Note 3 Et Total unadjusted error (see Note 6) See Note 3 TYP MAX UNIT 0.6 1 LSB 1 LSB 0.5 See Note 3 EO MIN TLC2551/52 1.5 TLC2555 2.5 TLC2551/52 2 TLC2555 5 TLC2551/52 2 TLC2555 5 LSB LSB LSB NOTES: 3. Analog input voltages greater than that applied to VREF convert as all ones (111111111111). 4. Linear error is the maximum deviation from the best straight line through the A/D transfer characteristics. 5. Zero error is the difference between 000000000000 and the converted output for zero input voltage: full-scale error is the difference between 111111111111 and the converted output for full-scale input voltage. 6. Total unadjusted error comprises linearity, zero, and full-scale errors. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 PARAMETER MEASUREMENT INFORMATION t(sample) tc tw(H_SCLK) VIH 1 2 4 12 16 44 SCLK VIL tw(L_SCLK) tsu(CSL-SCLKL) t(powerdown) CS th(SCLKL-FSL) tw(H_CS) tsu(FSH-SCLKL) th(EOC-CSH) td(CSL-FSH) td(SCLKH-SDOV) FS SDO IIIII IIIII tw(H_FS) OD11 OD8 OD0 td(CSL-SDOV) IIIII IIIII td(SCLK17H-SDOZ) Figure 6. TLC2551 Critical Timing (Control via CS and FS or FS only) t(sample) tsu(CSL-SCLKL) 1 2 tc 4 12 16 44 SCLK t(powerdown) CS td(SCLKH-SDOV) SDO OD11 OD10 td(CSL-SDOV) OD9 OD0 IIIIIII IIIIIII td(SCLK17H-SDOZ) Figure 7. TLC2551 Critical Timing (Control via CS only, FS = 1) 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 th(EOC-CSH) TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 PARAMETER MEASUREMENT INFORMATION t(sample) tc 1 1 4 12 16 44 SCLK t(reset cycle) MUX = AIN0 CS tw(H_CS) SDO th(EOC-CSH) td(SCLKH-SDOV) td(CSL-SDOV) IIII IIII OD11 IIIII IIIII OD0 td(CSL-SDOV) OD11 td(SCLK17H-SDOZ) Figure 8. TLC2552 Reset Cycle Critical Timing t(sample) tw(H_SCLK) VIH 1 2 4 12 tc 16 44 SCLK VIL tw(L_SCLK) th(SCLKL-CSL) t(powerdown) tsu(CSL-SCLKL) CS tw(H_CS) SDO th(EOC-CSH) td(SCLKH-SDOV) OD11 OD8 IIIII IIIII td(SCLK17H-SDOZ) OD0 td(CSL-SDOV) Figure 9. TLC2552 and TLC2555 Conversion Cycle Critical Timing POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 TYPICAL CHARACTERISTICS INTEGRAL NONLINEARITY vs FREE-AIR TEMPERATURE DIFFERENTIAL NONLINEARITY vs FREE-AIR TEMPERATURE 0.7 0.4 DNL - Differential Nonlinearity - LSB INL - Integral Nonlinearity - LSB VDD = REF = 5.5 V 400 KSPS 0.65 0.6 -40 25 TA - Free-Air Temperature - C VDD = REF = 5.5 V 400 KSPS 0.35 0.3 -40 90 25 TA - Free-Air Temperature - C Figure 10 90 Figure 11 OFFSET ERROR vs FREE-AIR TEMPERATURE GAIN ERROR vs FREE-AIR TEMPERATURE 0.5 0.9 VDD = REF = 5.5 V 400 KSPS VDD = REF = 5.5 V 400 KSPS Gain Error - LSB Offset Error - LSB 0.85 0.45 0.8 0.75 0.4 -40 25 TA - Free-Air Temperature - C 90 0.7 -40 Figure 12 14 25 TA - Free-Air Temperature - C Figure 13 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 90 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs FREE-AIR TEMPERATURE 3.1 Supply Current - mA VDD = REF = 5.5 V 400 KSPS 3.05 3 -40 25 TA - Free-Air Temperature - C 90 Figure 14 DNL - Differential Nonlinearity - LSB DIFFERENTIAL NONLINEARITY vs DIGITAL OUTPUT CODES 1 VDD = REF = 5 V 400 KSPS 0.5 0 -0.5 -1 4094 1 Digital Output Codes Figure 15 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 15 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 TYPICAL CHARACTERISTICS INL - Integral Nonlinearity - LSB INTEGRAL NONLINEARITY vs DIGITAL OUTPUT CODES 1 VDD = REF = 5 V 400 KSPS 0.5 0 -0.5 -1 4094 1 Digital Output Codes Figure 16 2048 POINTS FAST FOURIER TRANSFORM (FFT) 0 VDD = REF = 5.5 V 400 KSPS fi = 20 kHz Magnitude - dB -20 -40 -60 -80 -100 -120 -140 -160 0 20 40 60 80 100 120 140 f - Input Frequency - KHz Figure 17 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 160 180 200 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 TYPICAL CHARACTERISTICS EFFECTIVE NUMBER OF BITS vs INPUT FREQUENCY SIGNAL-TO-NOISE AND DISTORTION vs INPUT FREQUENCY 12 ENOB - Effective Number of Bits - Bits VDD = REF = 5.5 V 400 KSPS 73 71 69 67 VDD = REF = 5.5 V 400 KSPS 11.5 11 10.5 10 65 0 20 40 60 80 0 100 120 140 160 180 200 20 40 60 80 100 120 140 160 180 200 f - Input Frequency - KHz f - Input Frequency - KHz Figure 18 Figure 19 TOTAL HARMONIC DISTORTION vs INPUT FREQUENCY -65 THD - Total Harmonic Distortion - dB SINAD - Signal-To-Noise and Distortion - dB 75 VDD = REF = 5.5 V 400 KSPS -70 -75 -80 -85 -90 0 20 40 60 80 100 120 140 160 180 200 f - Input Frequency - KHz Figure 20 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 APPLICATION INFORMATION VDD VDD 10 k TLC2551 MISO FS SDO VDD SS CS AIN SCLK GND SCLK SPI PORT VREF EXT Reference (a) VDD VDD 10 k DR CLKX CLKR TLC2551 FS SDO VDD SCLK AIN FSX CS FSR GND DSP VREF EXT Reference (b) VDD TLC2551 FSX FSR DR CLKX FS VDD SDO SCLK AIN CLKR GPIO CS GND DSP VREF EXT Reference (c) Figure 21. Typical TLC2551 Interface to a TMS320 DSP 18 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLC2551, TLC2552, TLC2555 5-V, LOW-POWER, 12-BIT, 175/360 KSPS, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN SLAS276D - MARCH 2000 - REVISED MAY 2003 APPLICATION INFORMATION VDD TMS320 10 k EXT Reference 10 k FSX VDD CS SDO SCLK FSR DR CLKR VREF CLKX TLC2552/55 DSP GND AIN 0/AIN (+) AIN 1/AIN (-) For TLC2555 only Figure 22. Typical TLC2552/55 Interface to a TMS320 DSP POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 19 PACKAGE OPTION ADDENDUM www.ti.com 5-Oct-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TLC2551CDGK ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2551CDGKG4 ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2551CDGKR ACTIVE MSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2551CDGKRG4 ACTIVE MSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2551ID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2551IDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2551IDGK ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2551IDGKG4 ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2551IDGKRG4 ACTIVE MSOP DGK 8 TLC2551IDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2551IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2552CDGK ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2552CDGKG4 ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2552CDGKRG4 ACTIVE MSOP DGK 8 TBD Call TI TLC2552ID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2552IDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2552IDGK ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2552IDGKG4 ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2552IDGKRG4 ACTIVE MSOP DGK 8 TBD Call TI Call TI TLC2552IDRG4 ACTIVE SOIC D 8 TBD Call TI Call TI TBD Lead/Ball Finish Call TI MSL Peak Temp (3) Call TI Call TI TLC2555CDGKG4 ACTIVE MSOP DGK 8 TBD Call TI Call TI TLC2555CDGKRG4 ACTIVE MSOP DGK 8 TBD Call TI Call TI TLC2555ID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2555IDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2555IDGK ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2555IDGKG4 ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC2555IDGKRG4 ACTIVE MSOP DGK 8 TBD Call TI Call TI TLC2555IDRG4 ACTIVE SOIC D 8 TBD Call TI Call TI Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 5-Oct-2007 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TLC2551CDGKR MSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TLC2551IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TLC2551CDGKR MSOP DGK 8 2500 346.0 346.0 29.0 TLC2551IDR SOIC D 8 2500 346.0 346.0 29.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee(R) Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2008, Texas Instruments Incorporated