611 Industrial Way West, Eatontown, NJ 07724 tel: 732-460-0212 fax: 732-460-0214 sales@advanced-control.com www.advanced-control.com
Each detector model contains:
• DC return
• RF bypass capacitor
• Detector diode
• Video protection diode
Features:
• Microstrip or Stripline Compatible
• Static Protection
• High Sensitivity
• Small Size
• Easy Mounting
Applications:
• Transmitter Monitoring
• Radar Equipment
• Missile Guidance Systems
• Input to Low-Noise Amplifiers
• Broadband Or Narrowband ECM Receivers
• Power and Signal Monitors
• Doppler Radar and Beacon Receivers
• Matched units available for Multi-channel Receivers, Amplitude Comparator Systems and Discriminators
Minimum (5) Flatness Nominal (3)
Frequency Sensitivity vs Typical (2) Video Standard Optional
Range Part (1) K Frequency TSS Capacitance Case Case
(GHz) Number (mV/mW) (+/-dB) (dBm) (pF) Styles Styles
0.95 - 1.25 ACSM2036P 2000 0.2 -53 20 M51 M50
1 - 1.5 ACSM2155P 1700 0.25 -52 75 M51 M50
2 - 6 ACSM2030P 2000 0.3 -53 12 M51 M50
2 - 12 ACSM2032P 2000 1.0 -52 12 M51 M50
2 - 18 ACSM2031P 1700 1.3 -51 12 M51 M50
8 - 18 ACSM2033P 1700 1.0 -51 12 M51 M50
12 - 18 ACSM2034P 1800 0.75 -51 12 M51 M50
17 - 18 ACSM2139P 1700 0.5 -51 9 M51 M50
NOTES:
1) Standard output polarity is positive. If negative output is required, substitute “N” for “P” in part number.
2) Tangential Signal Sensitivity (TSS) is a measure of low level sensitivity with respect to noise. It is measured using a video amplifier with
a 2MHz bandwidth and a 3dB noise figure.
3) Video capacitance is used for RF bypass. This value can be changed if required for video response time or other considerations.
Contact the factory if value other than those shown are needed.
4) Video protection is available on most models. This feature helps to prevent damage to the detector diode from incidents occurring at the
video port. Transient electromagnetic spikes, static contact, or voltage surges can easily damage a detector diode. A video protection
diode will clamp the voltage at a value less than the detector breakdown voltage. NOTE: Inclusion of this protection will cause the
output voltage to compress and clamp. This occurs at about +10dBm input to the detector. If operation above +10dBm is required then
the output protection should be modified or excluded. Adding a suffix “X” at the end of the model number will exclude the video
protection feature. Contact the factory for assistance.
5) Standard bias is 100uA.
6) Zero bias schottky versions are available for most of listed biased schottky models with only minor differences in specifications.
a. The zero bias schottky has an impedance of several thousand ohms.
b. Zero bias schottky detectors exhibit less sensitive TSS due to the high diode impedance (typically a 3dB reduction).
c. The temperature performance of the zero bias schottky is poor when operating at low input power levels. This difference
becomes small at high levels (above 0dBm input power). The part number of zero bias versions includes a “Z” following the
polarity indicator.
Static protection and easy mounting are important features of these high
sensitivity detectors. They offer excellent octave or broadband RF performance
and rugged construction for harsh environments. The static protection virtually
eliminates damage due to handling or from video transients. The Bolt Channel
package allows for very simple and reliable screw-on mounting. The modified
package saves additional space by eliminating one thru hole. The standard
output polarity is positive. Negative output versions are available with slightly
lower sensitivity.
BOLT CHANNEL SCHOTTKY DETECTORS
611 Industrial Way West, Eatontown, NJ 07724 tel: 732-460-0212 fax: 732-460-0214 sales@advanced-control.com www.advanced-control.com
ENVIRONMENTAL SPECIFICATIONS: SCREENING :
MIL-E-5400, MIL-STD-202, MIL-E-16400 Standard Screening:
Operating Temp: -65°C to +125°C Internal Visual per MIL-STD-883, Method 2017
Storage Temp: -65°C to +150°C Temperature Cycle: -65°C to +100°C, 10 cycles
Humidity: MIL-STD-202F, M103, Cond B Optional High-Rel Screening (Ref MIL-PRF-38534):
Shock: MIL-STD-202F, M213, Cond B Internal Visual per MIL-STD-883, Method 2017
Altitude: MIL-STD-202F, M105, Cond B Stabilization Bake per MIL-STD-883, Method 1008
Vibration : MIL-STD-202F, M204, Cond B Temperature Cycle per MIL-STD-883, Method 1010
Thermal Shock: MIL-STD-202F, M107, Cond A Constant Acceleration per MIL-STD-883, Method 2001
Temperature Cycle: MIL-STD-202F, M105C, Cond D Burn-in per MIL-STD-883, Method 1015
Maximum Input Power: +20dBm Leak Test per MIL-STD-883, Method 1014
External Visual per MIL-STD-883, Method 2009
CASE STYLE M50 CASE STYLE M51
Part Number Ordering Information: Example: ACSM2033PZM51X20
ACSM2033: Bolt Channel Schottky Detector, 8 - 18GHz
P: Positive output polarity
Z: Zero bias version (omit for biased version)
M51: Package type
X: No video protection (omit for inclusion of video protection)
20: 20pF custom output capacitance (omit for standard value)
SMBC-0205
0.004 X 0.020
MIN. (2) PLCS.
0.020 MAX.
(TO FLAT)
COLORED DOT
INPUT
0.280±.005
0.160
0.205±.003
0.135±.010
(2) PLCS.
Ø0.096±.003
THRU
0.126±.004
0.062±.002
0.079±.002
0.080±.001
Ø0.096±.003 THRU
(2) PLCS.
0.126±.004
0.080±.001
0.161±.001
0.205±.003
COLORED DOT
INPUT
0.062±.002
0.135±.010
(2) PLCS.
0.252±.003
0.411±.002
0.079±.002
0.004 X 0.020
MIN. (2) PLCS.
0.020 MAX.
(TO FLAT)
