Hook and Loop F asteners
Trial Bags
TB3000 Back to back, self mating
TB3401/TB3402 No adhesive, sew-on
TB3506/TB3507 Thin with General Purpose Acrylic PSA
TB3526N/TB3527N High Performance Rubber PSA
TB3530/TB3531 General Purpose Rubber PSA
TB3546/TB3547 General Purpose Acrylic PSA
TB3571/TB3572 H ig h Pe rf or ma nc e Ac ry l ic P SA
TB3576/TB3577 Polyester w/High Performance Acrylic PSA
Technical Data August, 2011
Product Descri pti on 3M™ Hook and Loop Fasteners consist of hooks and loops which engage to form a
quick fastening attachment and offer advanced closure alternatives to zippers,
screws, snaps, hooks, etc. They offer greater design flexibility, faster product
assembly, smoother and cleaner exterior surfaces and improved product performance
in many applications by simply pulling the strips apart by hand to disengage.
Thin Products
3M™ Hook and Loop Fastener TB3000 is a thin back to back hook and
loop fastener which can wrap around and attach to itself to be used for
bundling items. One side of the fastener is covered with tiny polypropylene
translucent hooks, about 1400 per square inch. These hooks can engage
with thousands of soft pliable thin polyester loops on the reverse side.
Available in Red, Black, and White.
3M™ Hook and Loop Fasteners TB3506/TB3507
Thin hook and loop fasteners offer clean smooth lines for applications
where aesthetics are critical. The hook side consists of tiny polypropylene
hooks, about 1400 per square inch. The loop side contains thousands of soft
pliable polyester loops. Both the hook and loop have a general purpose
acrylic pressure sensitive adhesive on the backside which will adhere to a
wide variety of substrates. Available in White only.
3M Hook and Loop Fasteners Trial Bags
Product Descri pti on
(continued) Nylon Products
The woven nylon hook backing has flexible, self-supporting inverted J-hooks
protruding up from the backing. There are approximately 300 hooks per square inch
(46 hooks/square cm). The woven nylon loop backing has thousands of soft, pliable
napped loops protruding above the backing, providing for thousands of openings
and closings (cycles). The hook and loop are preshrunk to insure maximum
dimensional stability and flatness. Available in black.
3M™ Hook and Loop Fasteners TB3401/TB3402 is a plain backed
fastener for applications not requiring an adhesive, most comm only sewn.
3M™ Hook and Loop Fasteners TB3526N/TB3527N
These hook and loop fasteners are coated on the backside with a high
performance rubber based pressure sensitive adhesive. This permits these
fasteners to be easily and conveniently attached to a variety of substrates.
3M™ Hook and Loop Fasteners TB3530/TB3531
These products are coated with a general purpose rubber based pressure
sensitive adhesive. They adhere well to low surface energy surfaces.
3M™ Hook and Loop Fasteners TB3546/TB3547
These hook and loop fasteners are coated on the backside with a general
purpose acrylic pressure sensitive adhesive designed to adhere to variety of
surfaces including low surface energy materials while still providing good
temperature resistance.
3M™ Hook and Loop Fasteners TB3571/TB3572
Coated with high performance acrylic pressure sensitive adhesive which
has high temperature resistance and is resistant to many environmental and
chemical conditions.
Polyester Products
3M™ Hook and Loop Fasteners TB3576/TB3577
The woven polyester hook backing has flexible, self-supporting inverted
J-hooks protruding up from the backing. There are approximately 300
hooks per square inch (46 hooks/square cm). The woven polyester loop
backing has thousands of soft, pliable napped loops protruding above the
backing, providing a thousand openings and closings (cycles). The
polyester offers a durable moisture resistant fastener to resist the most
humid/wet conditions. Coated with high performance acrylic pressure
sensitive adhesive which has high temperature resistance and resistant to
many environmental and chemical conditions. Available in Black.
- 2 -
Acrylic
Adhesive
3M Hook and Loop Fasteners Trial Bags
Product
Construction Note: The following technical information and data should be considered representative it is not
product release requirements, nor product specifications. Rather this data represent
typical performance using standard test methods. Th is is intended for use as a guide to
assist in selection of 3M™ Hook and Loop Fasteners for further evaluation. Custom er
specifications should not be based solely on the data presented in this document.
Backing
3M™
Hook
and
Loop
Fasteners
Material
Backing
Unmated
Mated
without
Liner
Liner
Full
Roll
Product
Number
3M™ Fasteners
Back
to
Back
TB3000
Hook-polypropylene
Loop-Nylon
No
Adhesive
Back to
Back
Hook
and
Loop
0.027"
0.053"
(1.3
mm)
none
SJ3000
Plain
Back
TB3401
TB3402
Loop-Woven
Nylon
Hook-Woven
Nylon
No
Adhesive
Sew
on
0.080"
(2.0mm)
0.080"
(2.0mm)
0.125"
(3.2mm)
none
SJ3401
SJ3402
Acrylic
TB3506
TB3507
Hook-polypropylene
Loop-Polyester
General
Purpose
Acrylic
.023"
(.59mm)
.012"
(.30mm)
.32"
(.80mm)
83 lb
Brown
Polykraft with
green
3M
SJ3506
SJ3507
High
Performance
Rubber
Adhesive
TB3526N
TB3527N
Hook-Woven
Nylon
Loop-Woven
Nylon
High
Performance
Rubber
PSA
.091"
(.59mm)
.125"
(.30mm)
.14"
(3.6
mm)
3 mil
White
Polyethylene
with
red
“3M”
SJ3526N
SJ3527N
General
Performance
Rubber
Adhesive
TB3530
TB3531
Hook-Woven
Nylon
Loop-Woven
Nylon
General
Purpose
Rubber
PSA
.091"
(.59mm)
.125"
(.30mm)
.14"
(3.6
mm)
3
mil
White
Polypropylene
SJ3530
SJ3531
General
Purpose
Acrylic
Adhesive
TB3546
TB3547
Hook-Woven
Nylon
Loop-Woven
Nylon
General
Purpose
Acrylic
.091"
(.59mm)
.125"
(.30mm)
.14"
(3.6
mm)
4.0 mil
Clear
Silicone
treated
Polyolefin
with
embossed
3M
logo
SJ3546
SJ3547
High
Performance
Acrylic
Adhesive
TB3571
TB3572
Hook-Woven
Nylon
Loop-Woven
Nylon
High
Performance
Acrylic
PSA
.091"
(.59mm)
.125"
(.30mm)
.14"
(3.6
mm)
4.0 mil
Clear
Polyolefin
with
embossed
3M
logo
SJ3571
SJ3572
High
Performance
TB3576
TB3577
Hook-Woven
Polyester
Loop-Woven
Polyester
High
Performance
Acrylic
PSA
.080"
(2.0mm)
.065"
(1.7mm)
.14"
(3.6
mm)
4.0 mil
Clear
Polyolefin
with
embossed
3M
logo
SJ3576
SJ3577
- 3 -
3M Hook and Loop Fasteners Trial Bags
System Performance Note: Unless stated, typical system performance characteristics were measured under
controlled laboratory conditions of 72°F (22°C) and 50% relative humidity. The
user should evaluate products in the actual application to ensure suitable
performance for the intended use.
Typical System
Test V alues for
3M™ Hook and Loop
Nylon
Hook
to
Nylon
Loop
Polyester
Hook
3M™ TB3576 to
Polyester
Loop
3M™ TB3577
Thin
Hook
3M™
TB3506
to
Thin
Loop
3M™
TB3507
Back
to
Back
3M™
Hook
and
Loop
TB3000
Dynamic
Tensile Lbs/in 2
11
11
2.7
N/A
Dynamic Shear
Lbs/in2
22
18
42
31
“T” Peel
Lbs/inch width
12 inches per
minute
2.0
1.2
0.38
2.0
90° Peel
Lbs/inch width
12 inches per
minute
2.2
1.8
8.7
3.0
Cleavage Peel 7.5 4.6 4.2 N/A
Cycle Life # of
Closures before
losing 50% of
the initial peel
value
5000
1000
25
10
- 4 -
3M Hook and Loop Fasteners Trial Bags
Product Performance Note: The following technical information and data should be considered representative
or typical only and should not be used for specification purposes.
This guide should assist you in determining which product will adhere best to your
substrate for your application.
3M™ Hook and
Loop Fasteners
Trial Bags
Poly- Poly- EVA
propylene ethylene
(29) (31) (33)
Low Surface Energy
Acrylic PC ABS
(38) (42) (42)
Medium Surface Energy
Aluminum Stainless
Steel
(840) (700-1100)
High Surface Energy
Temperature
Resistance °F
TB3000 Bundle Bundle Bundle Bundle Bundle Bundle Bundle Bundle 200
TB3401
TB3402 Sewable Sewable Sewable Sewable Sewable Sewable Sewable Sewable 200
TB3506
TB3507 X X X X X 158
TB3526N
TB3527N X X X X X X X X 120
TB3530
TB3531 X X X X X X X X 90
TB3546
TB3547 X X X X X 180
TB3571
TB3572 X X X X X 200
TB3576
TB3577 X X X X X 200
X = Typically good adhesion without the use of surface primers
- 5 -
3M Hook and Loop Fasteners Trial Bags
Attachment Techniques The following information is intended to assist the designer considering the use
of adhesive-coated 3M™ Hook and Loop Fasteners. System product
performance depends upon a number of factors, including the fastener (material,
adhesive and area), application method, surface characteristics (material,
texture and cleanliness), environmental conditions (moisture, ultraviolet and
temperature exposure) plus the time it is expected to support a given load. Because
many of these factors are uniquely within the user s knowledge and control, it is
required that the user evaluate 3M products to determine whether they are fit for a
particular purpose and suitable for the user s substrates, method of application and
desired end use.
Design Consi de r at ions As a general rule, four square inches of fastener adhesive area per pound (57.3
square centimeters per kilogram) of static load to be supported is suggested as a
starting point for evaluation. More or less area may be needed depending on
specific conditions or end use applications.
Rounding the corners, slightly recessing the product into the substrate or providing
raised edges around the reclosable fastener can reduce the possibility of edge lifting
and improve the overall appearance of the fastener on the finished product.
Mechanically securing the corners of the fastener with rivets, staples, screws, etc.
may also reduce the possibility of edge lifting, but may reduce the closure
performance.
The two most common techniques for attaching these 3M™ Hook and Loop™
Fasteners to various surfaces are summarized below.
1) Pressure Sensitive Adhesive attachment: The use of pressure sensitive
adhesives eliminates or reduces the need for sew ing, solvent activation, dielectric or
ultrasonic bonding or bulk adhesive bonding. This can result in simplicity,
improved safety and lower installation costs. Pressure sensitive adhesive products
can be applied manually or automatically using a variety of equipment choices.
Contact your 3M sales representative to discuss automated equipment options.
- 6 -
3M Hook and Loop Fasteners Trial Bags
Surface Preparation Highly textured surfaces may reduce the ultimate adhesion levels and care should be
given to minimize the surface texture or roughness. Adhesive backed 3M™ Hook
and Loop Fasteners should be applied to surfaces that are clean, dry and free of oil,
grease, dust, mold release agents or surface contam inants that could reduce the
adhesion. It is recommended to remove any surface contam inants that may reduce
adhesion by using a method suited for the type and quantity of surface contaminants
present.
Note: It is important for the customer to follow all manufacturers precautions and
directions for use as well as any specific government regulations or customer and
supplier requirements for the method(s) used to remove any contamination on the
surface of the Substrate or preparing the surface for attaching the fastener(s).
In exceptional cases, especially when removing silicone mold release agents or on
rough, porous surfaces, it may be necessary to lightly abrade the surface, use an
adhesion promoter, or surface sealer to optimize the adhesive bond to the substrate.
The selection of abrasion, priming or sealing methods will depend upon the substrates
and the environmental conditions the product will be exposed to during use.
Attachment Techniques To obtain an optimum bond to any surface, both the fasteners and the target surfaces
should have equilibrated for a minimum of 1 hour at tem p eratures betw een 68°F
(20°C) to 100°F (38°C) before application. The liner protecting the adhesive is
removed and preferably without touching the adhesive, the fastener is applied to the
substrate. Exposure of the adhesive to ambient conditions without the protective
liner, before applying to the surface, should be minimized as initial adhesive tack
may decrease. Flexible materials should be lying on a hard flat surface so as to
permit uniform adhesive contact with the surface. Use of a rubber hand roller, press
platen or similar device is recommended to ensure full adhesive contact or wet-out
with the substrate surface. Approximately 4.5 pounds of force per square inch,
(310 grams per square centimeter) is recommended to increase adhesive contact,
improving bond strength. For all adhesive applications, it is im portant to ensure that
the edges are rolled down to reduce the chance of edge lifting.
Storage Store in original packaging between 60° to 80°F (16° to 27°C) and 40 to 60%
relative humidity.
- 7 -
3M Hook and Loop Fasteners Trial Bags
Certification/
Recognition MSDS: 3M has not prepared a MSDS for this product which is not subject to the MSDS requirements of
the Occupational Safety and Health Administration’s Hazard Communication Standard, 29 C.F.R.
1910.1200(b)(6)(v). When used under reasonable conditions or in accordance with the 3M directions for
use, the product should not present a health or safety hazard. However, use or processing of the product
in a manner not in accordance with the directions for use may affect its performance and present
potential health or safety hazards.
TSCA: This product is defined as an article under the Toxic Substances Control Act and therefore, it is
exempt from inventory listing requirements.
Technical Information The technical information, recommendations and other statements contained in this document are
based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such
information is not guaranteed.
Product Use Many factors beyond 3M’s control and uniquely within user ’s knowledge and control can affect the use
and performance of a 3M product in a particular application. Given the variety of factors that can affect
the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and
determining whether it is fit for a particular purpose and suitable for user’s method of application.
Warranty,
Limited Remedy,
and Disclaimer
Unless an additional warranty is specifically stated on the applicable 3M product packaging or product
literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time
3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY
OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE.
If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s
option, replacement of the 3M product or refund of the purchase price.
Limitation of Liability Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product,
whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted,
including warranty, contract, negligence or strict liability.
ISO 9001:
2000 -
ISO/TS 1 6949:2002
This Industrial Adhesives and Tapes Division product
was
manufactured under a 3M quality system
registered to ISO
9001:
2000 and ISO/TS 16949:2002
standards.
Industrial Adhesives and Tapes Division
3M Center, Building 225-3S-06
St. Paul, MN 55144-1000
800-362-3550 • 877-369-2923 (Fax)
www.3M.com/industrial
Recycled Paper
40% pre-consumer
10% post-consumer
- 8 -
3M is a trademark of 3M Company.
Printed in U.S.A.
©3M 2011 70070940617 (8/11)
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
3M:
TB3000 BLACK TB3000 RED TB3000 WHITE TB3401/TB3402 TB3506/TB3507 TB3526N/TB3527N
TB3530/TB3531 TB3546/TB3547 TB3571/TB3572 TB3576/TB3577