Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 Features: * * * * 5,000 Vrms electrical isolation Choice of a Single and Dual LED Phototransistor or Photo Darlington Sensor Low-cost plastic Dual-In-Line (DIP) package Approval Agency: * * UL Certification No: E58730 VDE Pending Description: The OPIA series optocouplers are designed for applications that use an analog output (Phototransistor or Photo Darlington) in a dual-in-line package. A wide selection of configurations are available. With typical isolation voltage of 5,000 Volts RMS, these products meet typical power system isolation requirements. Theory of operation: The LED transmitter is used to illuminate the Photosensor providing electrical isolation between two power systems while maintaining the ability to transmit information from one power system to the other. In many applications, analog signal levels may be required to be transmitted between two power systems while maintaining isolation between the power systems up to 5,000 volts RMS. A variety of LED and photosensor configurations are available depending on the system requirements. The ratio Current Transfer Ratio (CTR) is identified between the output current and input current for analog photosensors. CTR ratios can range from as low as 5 to over 9,000 depending on the device. CTR = Photosensor - Current 20mA = * 100 = 200 10mA LED - Current All DIP product is shipped in a shipping tube with "TU" identified on the end of the part number. Example: OPI400DTU is a 4-Pin DIP shipped in a tube (TU). Applications: * * * * * High voltage isolation, up to 5,000 Volts RMS PCBoard power system isolation Industrial equipment power isolation Medical equipment power isolation Office equipment RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.4 11/08 Page 1 of 17 Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 Package Outline Dimensions and Schematics: Top-View Pin # Part Number 1 2 3 4 OPIA400 A K E C OPIA410 A-K K-A E C OPIA411 A K E C OPIA412 A K E C OPIA413 A K E C Analog Output Devices Ordering Information OPIA400D Isolation Voltage Max. (Vrms) 5,000 CTR Min/Typ/Max 50 / - / 600 OPIA410D 5,000 60 / - / 600 5/4 4-Pin DIP A K, K A--C E OPIA411D 5,000 70 / - / - 80 / 72 4-Pin DIP A K--C E (Dar) OPIA412D 5,000 600 / - / 9,000 60 / 50 4-Pin DIP A K--C E (Dar) OPIA413D 5,000 50 / - / 600 2/3 4-Pin DIP A K--C E E = Emitter (Dar) = Photodarlington Part Number Configuration Information Packaging LED Sensor Typ. Tr / Tf (s) RL = 100 ohms 4/3 Package Configuration 4-Pin DIP A K--C E Configuration: Definition of Terms LED Identification--Sensor Identification A = Anode K = Cathode B = Base Part Number Suffix: C = Collector TU = Shipped in Tubes Example: OPIA400DTU OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 11/08 Page 2 of 17 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 Absolute Maximum Ratings (TA = 25o C unless otherwise noted) Storage Temperature Operating Temperature -55 C to +125 C -30 C to +100 C Isolation voltage (1 minute) Total Package Power Dissipation Lead Soldering Temperature (1/16" (1.6 mm) from case for 5 seconds with soldering iron) 5,000 Vrms 200 mW 260 C Input Diode Continuous Forward Current Peak Forward current (1 s pulse width, 300 pps) Reverse Voltage OPIA400, OPIA411, OPIA412, OPIA413 OPIA410, OPIA412 Power Dissipation 50 mA 1A 6V 70 mW Output Phototransistor Collector-Emitter Voltage OPIA400, OPIA410 OPIA412 OPIA411 OPIA413 Emitter-Collector Voltage OPIA400, OPIA410, OPIA411 OPIA412 OPIA413 Collector Current OPIA400, OPIA410, OPIA413 OPIA412 OPIA411 Power Dissipation All except the part numbers noted below OPIA412 60 V 300 V 35 V 350 V 6V 0.1 V 7V 50 mA 150 mA 80 mA 150 mW 200 mW OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.4 11/08 Page 3 of 17 Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 Electrical Characteristics SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS 1.0 1.2 1.2 1.4 1.3 V IF = 20 mA IF = 10 mA Input Diode VF Forward Voltage All except those noted below OPIA413 VFM Peek Forward Voltage OPIA410, OPIA412 OPIA413 - - 3.5 3.0 V IFM = 500 mA IR Reverse Current All except those noted below OPIA410 OPIA413 - - 10 10 A VR = 4 V VR = 5 V Ct Terminal Capacitance All except those noted below OPIA411 - 30 30 250 pf V = 0.0 V, f = 1K Hz V = 0.0 V, f = 1K Hz Collector Dark Current OPIA400, OPIA410 OPIA413 - 10 100 200 nA IF = 0 mA, VCE = 20 V IF = 0 mA, VCE = 300 V Collector-Emitter Saturation Voltage OPIA400 OPIA410 OPIA413 - 0.1 0.1 - 0.2 0.3 0.4 V IF = 20 mA, IC = 1 mA IF = 20 mA, IC = 1 mA IF = 8 mA, IC = 2.4 mA fC Cutt-Off Frequency All except those noted below OPIA400, OPIA410, OPIA413 - 80 - K Hz VCC = 5 V, IC = 2 mA, RL = 100 tr Rise Time OPIA400 OPIA410 OPIA413 - 4 5 2 18 20 - s VCC = 2 V, IC = 2 mA, RL = 100 VCC = 2 V, IC = 2 mA, RL = 100 VCC = 10 V, IC = 2 mA, RL = 100 tf Fall Time OPIA400 OPIA410 OPIA413 - 3 4 3 18 20 - s VCC = 2 V, IC = 2 mA, RL = 100 VCC = 2 V, IC = 2 mA, RL = 100 VCC = 10 V, IC = 2 mA, RL = 100 Output Phototransistor ICEO VCE(SAT) Continued on Next Page OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 11/08 Page 4 of 17 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 Electrical Characteristics - Continued from Previous Page SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Collector Dark Current OPIA412 OPIA411 - - 1.0 1.0 A IF = 0 mA, VCE = 200 V IF = 0 mA, VCE = 10 V Collector-Emitter Saturation Voltage OPIA411 OPIA412 - 0.8 - 1.0 1.5 V IF = 20 mA, IC = 5 mA IF = 20 mA, IC = 5 mA 1.0 - 6.0 7.0 - K Hz VCC = 2 V, IC = 20 mA, RL = 100 VCC = 5 V, IC = 2 mA, RL = 100 Output PhotoDarlington ICEO VCE(SAT) fC Cut-Off frequency OPIA411 OPIA412 tr Rise Time OPIA411 OPIA412 - 80 60 300 300 s VCC = 2 V, IC = 20 mA, RL = 100 VCC = 2 V, IC = 20 mA, RL = 100 tf Fall Time OPIA411 OPIA412 - 72 50 250 250 s VCC = 2 V, IC = 20 mA, RL = 100 VCC = 2 V, IC = 20 mA, RL = 100 CTR Current Transfer Ratio OPIA400, OPIA413 OPIA410 OPIA411 OPIA412 50 60 70 600 - 600 600 9,000 % IF = 5.00 mA, VCE = 5.0 V IF = 1.00 mA, VCE = 2.0 V IF = 0.05 mA, VCE = 3.3 V IF = 1.00 mA, VCE = 2.0 V Cf Floating Capacitance - 0.6 1.0 pF V = 0.0 V, f = 1M Hz - ohm Coupled Characteristics RISO Isolation Resistance 5X10 10 11 10 C500V, 40% to 60%RH OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.4 11/08 Page 5 of 17 Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 OPIA400 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 11/08 Page 6 of 17 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 OPIA400 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.4 11/08 Page 7 of 17 Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 OPIA410 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 11/08 Page 8 of 17 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 OPIA410 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.4 11/08 Page 9 of 17 Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 OPIA411 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 11/08 Page 10 of 17 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 OPIA411 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.4 11/08 Page 11 of 17 Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 OPI412 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 11/08 Page 12 of 17 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 OPI412 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.4 11/08 Page 13 of 17 Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 OPIA413 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 11/08 Page 14 of 17 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 OPIA413 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.4 11/08 Page 15 of 17 Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 Quality / Reliability Requirements Failure Criteria Conditions 10% 11 samples after 500Hrs 0 Fail @ VCE = 5.0VDC, Ta = 70C 10% 50 samples after 96Hrs 0 Fail @ Max PD, Ta = 25C MTTF @ 90% confidence 150,000 Min. @ 25C, 25mADC Moisture Sensitivity Level MSL 1 per JDEC stnd J-STD-020B Lead Solderability 0 Fail per Method 208 of MIL-STD-202. 125C Min. DSC test method Temperature Humidity-Bias 20% 85C, 85%RH, 500Hrs, 80% min Iceo Temperature Cycle 20% per Method 1010.7 of MIL-STD-883E High Temperature Storage 20% 85C, 500Hrs Autoclave 0 Fail TA = 121C, Pressure = 15psi, Humidity = 100%, Time = 96Hrs Parameter HTRB D IC(OFF) HTFB D IC(ON) Glass Transition of body Note: This is to be performed when a change occurs to form, fit or function. Government and Industry Standard Compliance Requirements European Union's Reduction of Hazardous Substances (RoHS) Directive 2002/95/EC Label Identification Carrollton, TX, USA MADE IN TAIWAN DESCRIPTION: Size: 3" (7.4 cm) X 2.2" (5.5 cm) Lettering shall be black on white background. Format shall be as: Notes: 1. The DATE CODE is a 4-digit code for date of manufacture where YY is the last two digits of the year, and WW is week number of manufacture. 2. The LOT I.D. is the manufacturing location lot identification where Y is the year of manufacture, NNNN is a sequential lot identifier, and DDD is the day of the year of manufacture. - or use equivalent label format. OPTEK P/N __OPIA400D-TU__ IIIIIIIIIIIIIIIIIIIII QTY. ________N/A_________ IIIIIIIIIIIIIIIIIIIII DATE CODE _____(YYWW)___ IIIIIIIIIIIIIIIIIIIII LOT I.D. ____(Y-NNNNDDD)__ IIIIIIIIIIIIIIIIIIIII OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.4 11/08 Page 16 of 17 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Optocoupler--DIP Package OPIA400, OPIA410 through OPIA413 Packaging Information: Tube Optek's Optocoupler Part Numbers Packaging Quantities 4-PIN OPIA400D/A, OPIA410D/A P/H OPIA413D/A and 6-PIN SMD OPIA6XXD/A Series 8-PIN OPIA8XXD Series and OPID804D Inner 52 x 7 x 7.5 cm Qty Small Carton Medium Carton Large Carton 53.5 x 16 x 17.5 cm 53.5 x 30.7 x 17.5 cm 53.5 x 30.7 x 25 cm Weight Qty Weight Qty Weight Gross Weight Qty Weight Gross Weight Qty Gross Weight Weig ht 100 44 3,000 1.40 12,000 6.0 6.5 24,000 12.0 12.5 36,000 18.0 18.5 65 44 1,950 1.50 7,800 6.5 7.0 15,600 12.0 12.5 23,400 18.5 19.0 48 44 1,440 1.44 5,760 6.0 6.5 11,520 12.0 12.5 17,290 18.0 18.5 100 24 6,000 1.60 24,000 6.5 7.0 48,000 13.0 13.5 72,000 19.5 20.0 170 -- 10,200 -- M/F 4-PIN and 5-PIN OPIA401B - OPIA404B, OPIA414B, OPIA500B SOP 4-PIN SSOP OPIA405C - OPIA409C P/H = Pin-Hole Packages (Referred as D = Dual-In-Line Package) SMD = Standard Surface Mount Packages (Referred as A = 6.5mil SMD) M/F or SOP = Mini-Flat Packages or Small Outside Packages (Referred as B = 4.40mil SMD w/ 2.54mil LeadSpacing) SSOP = Shrink SOP Packages (Referred as C = 3.60mil SMD with 1.27mil Lead-Spacing) Tube Packaging Specifications (TU): DIMENSIONS ARE IN: INCHES TOLERANCE: 0.008 INCHES Quantity: 4-pin: 100pcs/tube OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.4 11/08 Page 17 of 17