HV QF N3 2 IP4787CZ32 DVI and HDMI interface ESD protection, DDC/CEC buffering, hot plug handling and backdrive protection Rev. 3 -- 19 December 2014 Product data sheet 1. Product profile 1.1 General description The IP4787CZ32 is designed to protect High-Definition Multimedia Interface (HDMI) receiver interfaces. It includes HDMI 5 V power management, Display Data Channel (DDC) buffering and decoupling, hot plug drive, backdrive protection, Consumer Electronic Control (CEC) buffering and decoupling, and 12 kV contact ElectroStatic Discharge (ESD) protection for all external I/Os, exceeding the IEC 61000-4-2, level 4 standard. The IP4787CZ32 incorporates Transmission Line Clamping (TLC) technology on the high-speed Transition-Minimized Differential Signaling (TMDS) lines to simplify routing and help reduce impedance discontinuities. All TMDS lines are protected by an impedance-matched diode configuration that minimizes impedance discontinuities caused by typical shunt diodes. The 5 V power management enables host access to the [Extended Display Identification Data (EDID)] memory even if no HDMI plug is connected. The overall load to the 5 V line is according to the HDMI requirements. The DDC lines use a buffering concept which decouples the internal capacitive load from the external capacitive load for use with standard Complementary Metal Oxide Semiconductor (CMOS) or Low Voltage Transistor-Transistor Logic (LVTTL) I/O cells down to 1.2 V. This buffering also redrives the DDC and CEC signals, allowing the use of longer or cheaper HDMI cables with a higher capacitance. The internal hot plug drive module simplifies the application of the HDMI receiver to control the hot plug signal. All lines provide appropriate integrated pull-ups and pull-downs for HDMI compliance and backdrive protection to guarantee that HDMI interface signals are not pulled down if the system is powered down or enters Standby mode. Only a single external capacitor is required for operation. 1.2 Features and benefits HDMI 2.0 and all backward compatible standards are supported 6.0 Gbps TMDS bit rate (600 Mcsc TMDS character rate) compatible Supports UHD 4k (2160p) 60 Hz display modes Impedance matched 100 differential transmission line ESD protection for TMDS lines (10 ). No Printed-Circuit Board (PCB) pre-compensation required Simplified flow-through routing utilizing less overall PCB space DDC capacitive decoupling between system side and HDMI connector side and buffering to drive cable with high capacitive load (> 700 pF/25 m) IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection All external I/O lines with ESD protection of at least 12 kV, exceeding the IEC 61000-4-2, level 4 standard Hot plug drive module Utility biasing module (HEAC compliant) CEC buffering and isolation, with integrated backdrive-protected 26 k pull-up Robust ESD protection without degradation after repeated ESD strikes Highest integration in a small footprint, PCB level, optimized RF routing, 32-pin HVQFN leadless package 1.3 Applications The IP4787CZ32 can be used for a wide range of HDMI sink devices, consumer and computing electronics: Digital High-Definition (HD) TV Set-top box PC monitor Projector Multimedia audio amplifier HDMI picture performance quality enhancer module Digital Visual Interface (DVI) IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 2 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 2. Pinning information &(&B&21 9&& 6<6 (6'B%<3$66 $&7,9( &(&B6<6 (1$%/(B/'2 WHUPLQDO LQGH[DUHD QF +273/8*B&75/ 2.1 Pinning 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B6<6 70'6B'B6<6 70'6B'B&21 70'6B&.B6<6 70'6B&.B&21 70'6B&.B6<6 70'6B&.B&21 70'6B'B&21 87,/,7<B&21 70'6B'B&21 ''&B&/.B&21 ''&B'$7B&21 +'0,B9B&21 +273/8*B&21 9&& 9 ''&B&/.B6<6 ''&B'$7B6<6 ,3&= DDD 7UDQVSDUHQWWRSYLHZ Fig 1. Pin configuration IP4787CZ32 2.2 Pin description Table 1. IP4787CZ32 IP4787CZ32 Pin description Pin Name Description 1 TMDS_D2+_SYS TMDS to ASIC inside system 2 TMDS_D2_SYS TMDS to ASIC inside system 3 TMDS_D1+_SYS TMDS to ASIC inside system 4 TMDS_D1_SYS TMDS to ASIC inside system 5 TMDS_D0+_SYS TMDS to ASIC inside system 6 TMDS_D0_SYS TMDS to ASIC inside system 7 TMDS_CK+_SYS TMDS to ASIC inside system 8 TMDS_CK_SYS TMDS to ASIC inside system 9 DDC_CLK_SYS DDC clock system side 10 DDC_DAT_SYS DDC data system side 11 VCC(5V0) 5 V supply input 12 HOTPLUG_CON hot plug output to connector 13 HDMI_5V0_CON 5 V input from connector 14 DDC_DAT_CON DDC data connector side All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 3 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection Table 1. Pin description ...continued Pin Name Description 15 DDC_CLK_CON DDC clock connector side 16 UTILITY_CON utility line ESD protection 17 TMDS_CK_CON TMDS ESD protection to connector 18 TMDS_CK+_CON TMDS ESD protection to connector 19 TMDS_D0_CON TMDS ESD protection to connector 20 TMDS_D0+_CON TMDS ESD protection to connector 21 TMDS_D1_CON TMDS ESD protection to connector 22 TMDS_D1+_CON TMDS ESD protection to connector 23 TMDS_D2_CON TMDS ESD protection to connector 24 TMDS_D2+_CON TMDS ESD protection to connector 25 CEC_CON CEC signal connector side 26 ESD_BYPASS ESD bias voltage 27 VCC(SYS) supply voltage for level shifting 28 ACTIVE CEC Standby mode control (LOW for lowest power, CEC-only mode) 29 CEC_SYS CEC I/O signal system side 30 ENABLE_LDO 5 V LDO enable 31 n.c. not connected 32 HOTPLUG_CTRL hot plug control input from system side ground pad GND ground 3. Ordering information Table 2. Ordering information Type number Package Name IP4787CZ32 IP4787CZ32 IP4787CZ32 Description Version HVQFN32 plastic thermal enhanced very thin quad flat package; SOT617-3 no leads; 32 terminals; body 5 5 0.85 mm All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 4 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 4. Functional diagram TMDS_D2+_SYS TMDS_D2+_CON ESD TMDS_D2-_SYS TMDS_D2-_CON TMDS_D1+_SYS TMDS_D1+_CON TMDS_D1-_SYS TMDS_D1-_CON TMDS_D0+_SYS TMDS_D0+_CON TMDS_D0-_SYS TMDS_D0-_CON TMDS_CK+_SYS TMDS_CK+_CON TMDS_CK-_SYS TMDS_CK-_CON INT_5V0 ESD 3.3 V VOLTAGE REGULATOR INT_VCC(SYS) ESD CEC driver 10 k 26 k CEC_SYS CEC_CON ESD HDMI_5V0_CON INT_VCC(SYS) ESD DDC driver 3.65 k 47 k DDC_CLK_SYS DDC_CLK_CON INT_VCC(SYS) ESD HDMI_5V0_CON ESD DDC driver 3.65 k 47 k DDC_DAT_SYS DDC_DAT_CON Hot plug driver / bias ESD ESD HOTPLUG_CTRL HOTPLUG_CON 100 k ESD Utility bias ESD UTILITY_CON VCC(5V0) INT_5V0 INT_VCC(SYS) ESD ESD 680 k HDMI_5V0_CON ENABLE_LDO 5V Control VCC(SYS) INT_5V0 ESD ESD enable enLim enRef POWER MANAGEMENT UNIT ACTIVE enCEC VCC(SYS) VCC(SYS) 680 k INT_5V0 ibias 1..n vref 1..m ESD n ESD_BYPASS m INT_VCC(SYS) CURRENT-/VOLTAGEREFERENCES aaa-004322 Fig 2. IP4787CZ32 IP4787CZ32 Functional diagram All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 5 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 5. Limiting values Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VCC(5V0) supply voltage (5.0 V) VI input voltage I/O pins VESD electrostatic discharge voltage IEC 61000-4-2, level 4 (contact) [1] - 12 kV IEC 61000-4-2, level 1 (contact) [2] - 2 kV total power dissipation DDC operating at 100 kHz; CEC operating at 1 kHz; 50 % duty cycle; ACTIVE = HIGH - 50 mW DDC and CEC bus in idle mode; ACTIVE = HIGH - 3.0 mW DDC and CEC bus in idle mode; ACTIVE = LOW - 1.2 mW Ptot Conditions Min Max GND 0.5 6.5 GND 0.5 5.5 Unit V V Tamb ambient temperature 25 +85 C Tstg storage temperature 55 +125 C [1] Connector-side pins (typically denoted with `_CON' suffix) to ground. [2] System-side pins: CEC_SYS, DDC_DAT_SYS, DDC_CLK_SYS, HOTPLUG_CTRL, ACTIVE, VCC(SYS) and VCC(5V0). IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 6 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 6. Static characteristics Table 4. Supplies Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter VCC(5V0) supply voltage (5.0 V) Conditions V(HDMI_5V0_CON) voltage on pin HDMI_5V0_CON VCC(SYS) system supply voltage [1] [1] Min Typ Max Unit 4.5 5.0 6.5 V 4.5 5.0 6.5 V 1.1 3.3 3.63 V HDMI_5V0_CON is used as supply in case ENABLE_LDO is inactive and VCC(5V0) is unavailable or lower than HDMI_5V0_CON. Table 5. TMDS protection circuit Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 90 100 110 - 0.6 - pF 6.0 - 9.0 V - 1.0 - - 1.0 - - 1.0 - - 1.0 - - 0.1 1.0 A - 1.0 - A - 0.7 - V - 8.0 - V TMDS channel Zi(dif) differential input impedance TDR measured; tr = 200 ps Ceff effective capacitance equivalent shunt capacitance for TDR minimum; tr = 200 ps [1][2] Protection diode VBRzd Zener diode breakdown voltage I = 1.0 mA rdyn dynamic resistance surge; I = 1.0 A; IEC 61000-4-5/9 positive transient negative transient TLP [3] positive transient negative transient Ibck back current VCC(5V0) < Vch(TMDS) VI = 3.0 V ILR reverse leakage current VF forward voltage VCL(ch)trt(pos) positive transient channel clamping voltage 100 ns TLP; 50 pulser at 50 ns [1] This parameter is guaranteed by design. [2] Capacitive dip at HDMI Time Domain Reflectometer (TDR) measurement conditions. [4][5] [3] ANSI-ESD SP5.5.1-2004, ESD sensitivity testing Transmission Line Pulse (TLP) component level method 50 TDR. [4] Signal pins: TMDS_D0+_CON, TMDS_D0_CON, TMDS_D1+_CON, TMDS_D1_CON, TMDS_D2+_CON, TMDS_D2_CON, TMDS_CK+_CON, TMDS_CK_CON, TMDS_D0+_SYS, TMDS_D0_SYS, TMDS_D1+_SYS, TMDS_D1_SYS, TMDS_D2+_SYS, TMDS_D2_SYS, TMDS_CK+_SYS and TMDS_CK_SYS. [5] Backdrive current from TMDS_x_SYS and TMDS_x_CON pins to local VCC(5V0) bias rail at power-down. Device does not block backdrive current leakage through the device to/from ASIC I/O pins connected to TMDS_x_SYS pins. IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 7 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection Table 6. HDMI_5V0_CON Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter dynamic resistance rdyn Conditions Min Typ Max Unit positive transient - 1.0 - negative transient - 1.0 - - 8 - V [1] TLP VCL clamping voltage 100 ns TLP; 50 pulser at 50 ns II(max) maximum input current V(HDMI_5V0_CON) = 5.3 V Ibck back current VCC(5V0) < V(HDMI_5V0_CON) [2] - - 50 mA - - 10 A [1] ANSI-ESD SP5.5.1-2004, ESD sensitivity testing TLP component level method 50 TDR. [2] Ibck defines the current that flows from the VCC(5V0) pin into the system supply. This parameter is guaranteed by design. Table 7. Static characteristics Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit V DDC_CLK_CON; DDC_DAT_CON[1] VIH HIGH-level input voltage 0.5 V(HDMI_5V0_CON) 6.5 VIL LOW-level input voltage 0.5 - 0.3 V V(HDMI_5V0_CON) VOH HIGH-level output voltage V(HDMI_5V0_CON) 0.02 V(HDMI_5V0_CON) V + 0.02 VOL LOW-level output voltage internal pull-up and external sink - 100 200 mV VIK input clamping voltage II = 18 mA - - 1.0 V - 8.0 10 pF 42.3 47 51.7 k VCC(SYS) = 1.2 V 310 - - mV VCC(SYS) = 1.8 V 450 - - mV VCC(SYS) = 2.5 V 620 - - mV VCC(SYS) = 3.3 V 760 - - mV VCC(SYS) = 1.2 V - - 240 mV VCC(SYS) = 1.8 V - - 330 mV VCC(SYS) = 2.5 V - - 370 mV - - 390 mV CIO input/output capacitance Rpu pull-up resistance DDC_CLK_SYS; VIH VIL [2] VCC(5V0) = 5.0 V; VCC(SYS) = 3.3 V; ACTIVE = HIGH [2][3] DDC_DAT_SYS[1][4] HIGH-level input voltage LOW-level input voltage VCC(SYS) = 3.3 V VOH HIGH-level output voltage VOL LOW-level output voltage VIK IP4787CZ32 IP4787CZ32 input clamping voltage 0.8 VCC(SYS) - VCC(SYS) + 0.02 V VCC(SYS) = 1.2 V - 330 340 mV VCC(SYS) = 1.8 V - 490 500 mV VCC(SYS) = 2.5 V - 640 690 mV VCC(SYS) = 3.3 V - 685 790 mV II = 18 mA - - 1.0 V [2] All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 8 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection Table 7. Static characteristics ...continued Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter CIO input/output capacitance Rpu pull-up resistance Conditions VCC(5V0) = 0 V; VCC(SYS) = 0 V; Vbias = 2.5 V; AC input = 3.5 V(p-p); f = 100 kHz [2] Min Typ Max Unit - 6.0 8.0 pF 3.2 3.65 4.1 k CEC_CON[1] VIH HIGH-level input voltage 2.0 - - V VIL LOW-level input voltage - - 0.80 V VOH HIGH-level output voltage 2.88 3.3 3.63 V VOL LOW-level output voltage IOL = 1.5 mA CIO input/output capacitance VCC(5V0) = 0 V; VCC(SYS) = 0 V; Vbias = 1.65 V; AC input = 2.5 V(p-p); f = 100 kHz Rpu pull-up resistance Ileak(CEC) CEC leakage current - 100 200 mV - 8.0 10 pF 23.4 26.0 28.6 k VCC(5V0) = 0 V; VCC(SYS) = 0 V; CEC_CON connected to 3.63 V via 27 k - - 0.1 A VCC(SYS) = 1.2 V 310 - - mV VCC(SYS) = 1.8 V 450 - - mV VCC(SYS) = 2.5 V 620 - - mV VCC(SYS) = 3.3 V 760 - - mV VCC(SYS) = 1.2 V - - 240 mV VCC(SYS) = 1.8 V - - 330 mV VCC(SYS) = 2.5 V - - 370 mV - - 390 mV [2] CEC_SYS[1][4] VIH VIL HIGH-level input voltage LOW-level input voltage VCC(SYS) = 3.3 V VOH HIGH-level output voltage VOL LOW-level output voltage 0.8 VCC(SYS) - VCC(SYS) + 0.02 V VCC(SYS) = 1.2 V - 330 340 mV VCC(SYS) = 1.8 V - 490 500 mV VCC(SYS) = 2.5 V - 640 690 mV - 675 770 mV - 6.0 7.0 pF 8.5 10 11.5 k [2] VCC(SYS) = 3.3 V CIO input/output capacitance Rpu pull-up resistance IP4787CZ32 IP4787CZ32 VCC(5V0) = 0 V; VCC(SYS) = 0 V; Vbias = 1.65 V; AC input = 2.5 V(p-p); f = 100 kHz [2] All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 9 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection Table 7. Static characteristics ...continued Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter HOTPLUG_CON; Conditions Min Typ Max Unit 4.4 V UTILITY_CON[1] VOH HIGH-level output voltage 3.6 4 VOL LOW-level output voltage - - 0.4 V RO output resistance 0.8 1.0 1.2 k VCC(5V0) = 0 V; VCC(SYS) = 0 V; Vbias = 2.5 V; AC input = 3.5 V(p-p); f = 100 kHz [2] - 8.0 10 pF output capacitance CO HOTPLUG_CTRL[1] VIH HIGH-level input voltage HIGH = hot plug on [5] 1.0 - - V VIL LOW-level input voltage LOW = hot plug off [5] - - 0.4 V Rpd pull-down resistance 60 100 140 k VCC(5V0) = 0 V; VCC(SYS) = 0 V; Vbias = 2.5 V; AC input = 3.5 V(p-p); f = 100 kHz [2] - 6.0 7.0 pF input capacitance Ci [1] The device is active if the input voltage at pin ACTIVE is above the HIGH level. [2] This parameter is guaranteed by design. [3] Capacitive load measured at power-on. [4] No external pull-up resistor attached. [5] See Section 9.7 for details on the hot plug functionality. Table 8. Power management VCC(SYS) = 1.10 V to 3.63 V; VCC(5V0) = 4.5 V to 6.5 V; GND = 0 V; Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit System side: input pin ACTIVE[1] VIH HIGH-level input voltage VIL LOW-level input voltage Rpd pull-down resistance Ci input capacitance HIGH = active [2] 1.0 - - V LOW = standby [3] - - 0.4 V VI = 3 V or 0 V [4] - 6 7 pF - - V - 0.4 680 k System side: input pin ENABLE_LDO VIH HIGH-level input voltage 1.0 VIL LOW-level input voltage - Rpu pull-up resistance Ci input capacitance [1] 680 VI = 3 V or 0 V [4] - 6 V k 7 pF The ACTIVE pin should be connected permanently to VCC(5V0) or VCC(SYS) if no enable control is needed. [2] DDC buffers, Hot Plug Detect (HPD) driver, utility bias and HDMI_5V0_CON out enabled; CEC buffer enabled. [3] DDC buffers, HPD driver, utility bias and HDMI_5V0_CON out disabled; CEC buffer enabled. [4] This parameter is guaranteed by design. IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 10 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 7. Dynamic characteristics Table 9. Dynamic characteristics VCC(5V0) = 5.0 V; VCC(SYS) = 1.8 V; GND = 0 V; Tamb = 25 C to +85 C unless otherwise specified. Symbol Parameter Conditions DDC_DAT_SYS, DDC_CLK_SYS, DDC_DAT_CON, Min Typ Max Unit DDC_CLK_CON[1] tPLH LOW to HIGH propagation delay system side to connector side Figure 16 - 80 - ns tPHL HIGH to LOW propagation delay system side to connector side Figure 16 - 60 - ns tPLH LOW to HIGH propagation delay connector side to system side Figure 17 - 120 - ns tPHL HIGH to LOW propagation delay connector side to system side Figure 17 - 80 - ns tTLH LOW to HIGH transition time connector side Figure 18 - 150 - ns tTHL HIGH to LOW transition time connector side Figure 18 - 100 - ns tTLH LOW to HIGH transition time system side Figure 19 - 250 - ns tTHL HIGH to LOW transition time system side Figure 19 - 80 - ns [1] All dynamic measurements are done with a 75 pF load. Rise times on system side are determined only by internal pull-up resistors. Rise times on connector side are determined by external 1.5 k and internal pull-up resistors. DDD =GLI 70'6B&. 70'6B' 70'6B' 70'6B' WLPH QV tr = 200 ps; no filter; VCC(5V0) = 5 V 100 differential (CH1 + CH2) Fig 3. Differential TDR plot IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 11 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 018aaa086 3 Sdd21; Scc21 (dB) (1) -3 (2) -9 -15 106 107 108 109 1010 f (Hz) (1) Sdd21 (2) Scc21 Normalized to 100 ; differential pairs at signal pins. Fig 4. Mixed-mode differential and common-mode insertion loss; typical values 018aaa087 3 Sdd21 (dB) (1) -3 (2) -9 -15 106 107 108 109 1010 f (Hz) (1) Sdd21; Near End Crosstalk (NEXT) (2) Sdd21; Far End Crosstalk (FEXT) normalized to 100 ; differential pairs CH1/CH2 versus CH3/CH4 Fig 5. IP4787CZ32 IP4787CZ32 Mixed-mode differential and common-mode NEXT / FEXT; typical values All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 12 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection DDD 227 MHz pixel clock Horizontal scale: 200 mV/div Vertical scale: 90 ps/div Offset: 42.6 mV Fig 6. Eye diagram using IP4787CZ32 (1080p, 12 bit) DDD 297 MHz pixel clock Horizontal scale: 200 mV/div Vertical scale: 67.5 ps/div Offset: 42.6 mV Fig 7. IP4787CZ32 IP4787CZ32 Eye diagram using IP4787CZ32 (1080p, 16 bit) All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 13 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection aaa-013775 148.5 MHz test frequency Horizontal scale: 53.8 ps/div Vertical scale: 200 mV/div Measured at TP2 with worst cable emulator, reference cable equalizer and worst case negative skew Fig 8. Eye diagram using IP4787CZ32 (2160p, 60 Hz) 018aaa090 0.4 Cline (pF) 0.2 0.0 -0.2 -0.4 -1.0 1.0 3.0 5.0 7.0 Vbias (V) Deviation from typical capacitance normalized at Vbias = 2.5 V Fig 9. IP4787CZ32 IP4787CZ32 Eye diagram using IP4787CZ32 (2160p, 60 Hz) All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 14 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 018aaa091 4.00 VCL (V) 018aaa092 2.5 VCL (V) 3.75 2.0 3.50 1.5 3.25 3.00 0.5 0.6 0.7 0.8 0.9 1.0 1.1 I (A) 1.2 1.0 0.4 0.6 0.8 1.0 1.2 I (A) IEC 61000-4-5; tp = 8/20 s; positive pulse IEC 61000-4-5; tp = 8/20 s; negative pulse Fig 10. Dynamic resistance with positive clamping Fig 11. Dynamic resistance with negative clamping 018aaa093 14 I (A) 12 10 -4 8 -6 6 -8 4 -10 2 -12 0 6 10 14 18 22 018aaa094 0 I (A) -2 -14 -12 VCL (V) tp = 100 ns; TLP; signal pins; typical values IP4787CZ32 -4 0 VCL (V) tp = 100 ns; TLP; signal pins; typical values Fig 12. Dynamic resistance with positive clamping IP4787CZ32 -8 Fig 13. Dynamic resistance with negative clamping All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 15 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 018aaa095 6.5 VI (V) 018aaa096 6.0 VO (V) 6.0 (2) (5) (4) (1) 4.0 5.5 (1) 2.0 (3) 5.0 (4) (3) (2) 4.5 5.0 5.5 6.0 6.5 0.0 0.00 0.02 0.04 VCC(5V0) (V) (1) 5.3 V; maximum values; HDMI CTS TID 7-11 (1) VCC(5V0) = 4.5 V (2) 4.8 V; minimum values; HDMI CTS TID 7-11 (2) VCC(5V0) = 5.0 V (3) I = 0 mA (3) VCC(5V0) = 5.5 V (4) I = 55 mA (4) VCC(5V0) = 6.5 V 0.06 0.08 0.10 0.12 IO (A) 0.14 (5) VCC(5V0) supply input; 4.925 V to 6.5 V Fig 14. Overvoltage limiter function (HDMI_5V0_CON) IP4787CZ32 IP4787CZ32 Fig 15. Overcurrent limiter function (HDMI_5V0_CON) All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 16 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 8. AC waveforms 8.1 DDC propagation delay 9&& 6<6 ''&V\VWHPVLGH 9&& 6<6 92/ 6<6 9,/ 6<6 ''&FRQQHFWRUVLGH 9 ,17B9 9 ,17B9 9 ,17B9 92/ &21 W3+/ W3/+ DDD Fig 16. Propagation delay DDC, DDC system side to DDC connector side 9 ,17B9 ''&FRQQHFWRUVLGH 9 ,17B9 9 ,17B9 9,/ &21 9&& 6<6 ''&V\VWHPVLGH 9&& 6<6 W3+/ 9&& 6<6 W3/+ 92/ 6<6 DDD Fig 17. Propagation delay DDC, DDC connector side to DDC system side IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 17 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 8.2 DDC transition time ''&V\VWHPVLGH 9&& 6<6 9,/ 6<6 ,17B9 ''&FRQQHFWRUVLGH 9 ,17B9 9 ,17B9 92/ &21 W3/+ W3+/ DDD Fig 18. Transition time DDC connector side ,17B9 ''&FRQQHFWRUVLGH 9,/ &21 9&& 6<6 ''&V\VWHPVLGH 9&& 6<6 9&& 6<6 W3+/ W3/+ 92/ 6<6 DDD Fig 19. Transition time DDC system side IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 18 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9. Application information 9.1 HDMI connector side ESD protection All pins directly interfacing with the HDMI connector provide up to 12 kV contact ESD protection according to IEC 61000-4-2, exceeding level 4. In order to utilize the full scope of this protection it is recommended to connect all connector side pins to the HDMI connector. 9.2 TMDS ESD protection concept To protect the TMDS lines and also to comply with the impedance requirements of the HDMI specification, the IP4787CZ32 provides ESD protection with matched TLC ESD structures. Typical Dual Rail Clamp (DRC) or rail-to-rail shunt structures are common for low-capacitance ESD protection (Figure 20; left side) where the dominant factor for the TMDS line impedance dip is determined by the capacitive load to ground. Parasitic lead inductances of the packaging in this case work against the ESD clamping performance by including the I/t reactance of the inductance into the path of the ESD shunt. The IP4787CZ32 utilizes these inherent inductances in series with the transmission line in order to present an effective capacitive load of roughly only 0.7 pF. This TLC structure minimizes the capacitive dip, for ideal signal integrity (Figure 20; right side) without complicated PCB pre-compensation. As a beneficial side effect, this enhances the ESD performance of the device as well, since the reactance of the series inductance attenuates the fast initial peak of the ESD pulse for a lower residual pulse delivered to the Application Specific Integrated Circuit (ASIC). 018aaa102 018aaa101 a. Classic parallel ESD shunt protection b. Improved series shunt TLC clamping Fig 20. TLC ESD protection of TMDS lines IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 19 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.3 Operating and standby modes The operating mode of IP4787CZ32 depends on the availability of the VCC(5V0) and VCC(SYS) supply voltages and on the state of the ACTIVE input signal. Without availability of both supplies, IP4787CZ32 is in Standby mode. As soon as VCC(5V0) and VCC(SYS) are within the range specified in Section 6, the part is in an operating mode that can be controlled via the ACTIVE input signal. In case ACTIVE is LOW, only the CEC buffer is active and enabled to receive or send CEC commands. All other outputs are in a high-ohmic state. A HIGH input signal enables all parts of IP4787CZ32 and puts the device into full operating mode. Table 10. IP4787CZ32 operating modes VCC(SYS) VCC(5V0) ACTIVE[1] Mode Description < 1.1 V < 4.5 V X Standby mode all outputs high-ohmic 1.1 V 4.5 V L CEC Standby mode CEC circuit active; all other outputs high-ohmic H full operating mode all functional blocks active [1] X = Don't care (either LOW or HIGH level); L = LOW-level input; H = HIGH-level input If no CEC Standby mode is required, or if no special Power-down modes are desired, the ACTIVE pin can be pulled HIGH to VCC(5V0) or VCC(SYS) for continuous HDMI and CEC operation as soon as the supplies are aviailable. Strapping the ACTIVE = VCC(SYS) = VDD of ASIC guarantees that all interface signals ending with the suffix `_SYS' on the system side are disabled when VCC(SYS) goes LOW, protecting the ASIC I/O signals from exceeding its local VDD. In this mode, even if VCC(5V0) is powered, HDMI_5V0_CON goes active and hot plug events can be detected only when the ASIC power supply rail is on. Strapping ACTIVE = VCC(5V0) is the most basic configuration where the buffers are enabled whenever the local VCC(5V0) and VCC(SYS) supplies reach minimum operating levels. IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 20 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.4 DDC circuit The DDC bus circuit integrates all required pull-ups, and provides full capacitive decoupling between the HDMI connector and the DDC bus lines on the PCB. The capacitive decoupling ensures that the maximum capacitive load is well within the 50 pF maximum of the HDMI specification. No external pull-ups or pull-downs are required. The bidirectional buffers support high-capacitive load on the HDMI cable-side. Various non-compliant but prevalent low-cost cables have been observed with a capacitive load of up to 6 nF on the DDC lines, far exceeding the 700 pF HDMI limit. The IP4787CZ32 can easily decouple this from the weaker ASIC I/O buffers, and drive the rogue cable successfully. (6'B%<3$66 ,17B9 N ,17B9&& 6<6 (6'B%<3$66 N N N ''&B'$7B6<6 ''&B'$7B&21 ''&B&/.B6<6 ''&B&/.B&21 ,17B9&& 6<6 ,17B9 DDD DDD a. DDC clock b. DDC data Fig 21. DDC circuit 5 (1) 4 V 3 2 (2) 1 0 time 018aaa105 (1) Valid I2C signaling example on the cable (connector side) from 5 V (HIGH) to approximately 1 V (LOW). (2) Valid logic-level signaling example to the ASIC (system side) from 1.8 V (HIGH) to approximately 0.5 V (LOW). Fig 22. DDC level shifting waveform example IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 21 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.5 CEC circuit The logical multidrop topology of the CEC bus can include complex physical stubs, loading cables, and interconnects that may deteriorate signal quality. The IP4787CZ32 includes a full bidirectional buffer to drive the CEC bus and isolate the CEC microcontroller or ASIC General-Purpose Input/Output (GPIO). The CEC buffer derives power from an on-board 3.3 V regulator from the 5 V power domain (see Figure 23). This allows extensive system power management configurations and guarantees an HDMI-compliant V(CEC_CON) on the connector, as well as a backdrive-protected 125 A nominal CEC pull-up which does not degrade the bus when powered down. By placing the CEC microcontroller and either VCC(5V0) or HDMI_5V_CON input on a 5 V rail as shown in Figure 28, the CEC microcontroller can communicate over CEC for power commands, and then enable the HDMI port via the ACTIVE pin, as well as the rest of the system as needed. (6'B%<3$66 ,17B9 ,17B9&& 6<6 9 N N &(&B&21 &(&B6<6 DDD Fig 23. CEC module IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 22 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.6 Logic low I2C voltage shifter The DDC buffers provide an additional feature commonly required for high-integration HDMI ASICs which are limited to CMOS or LVTTL LOW-level input voltage (VIL) on their available I/O buffer cells. These I/Os are not strictly compliant with the 0.3 VDD threshold voltage levels of I2C and may miss intended logic LOW levels on the cable between 0.8 V and 1.5 V (typical values). This feature is also included in the CEC buffer thus allowing standard I/O buffer cells to be used in ASICs and microcontrollers connected to CEC_SYS. DDD 9 9&& 6<6 9 (1) VOL_CEC(max) maximum output voltage driven to system (ASIC) side when CEC is logic LOW (2) VOL_DDC(max) maximum output voltage driven to system (ASIC) side when DDC is logic LOW (3) VIL(max) maximum input voltage on system (ASIC) side to drive DDC or CEC logic LOW (4) VIH(min) minimum input voltage on system (ASIC) side to drive DDC or CEC logic HIGH Fig 24. Logic voltage thresholds as a function of supply voltage; on connector (HDMI) side IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 23 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.7 Hot plug circuit The IP4787CZ32 includes a hot plug drive circuit that simplifies the hot plug application. It drives an HDMI-compliant hot plug signal to the HDMI sink. By design, the hot plug drive circuit avoids glitches or short pulses on the hot plug line and is protected against shortage to the 5 V input. In order to signal a HIGH level on the HOTPLUG_CON output pin, the HOTPLUG_CTRL input pin needs to be driven HIGH and a 5 V supply needs to be available on HDMI_5V0_CON. Driving HOTPLUG_CTRL LOW generates a LOW-level output on the HOTPLUG_CON pin. An integrated 100 k resistor on the HOTPLUG_CTRL pin prevents from undefined (floating) state on HOTPLUG_CON. In full accordance with the HDMI specification, the LOW and HIGH output levels generated on the HOTPLUG_CON output always show a proper impedance of 1 k. (6'B%<3$66 +'0,B9B&21 N &21752/ %/2&. +273/8*B&21 +273/8*B&75/ N DDD Fig 25. Hot plug circuit 9.8 HEAC support and utility pin In addition to the ESD protection implemented at UTILITY_CON, IP4787CZ32 also includes a biasing output for HEAC functionality. This output buffer is closely tied to the output on the HOTPLUG_CON pin. A LOW-level output signal on HOTPLUG_CON also causes a low output on UTILITY_CON and a HIGH level on HOTPLUG_CON results in an identical high output on UTILITY_CON. As for HOTPLUG_CON, the LOW and HIGH output levels generated on the UTILITY_CON output always show an impedance of 1 k. (6'B%<3$66 N 87,/,7<B&21 +'0,B9B&21 &21752/ %/2&. +273/8*B&75/ N DDD Fig 26. Utility circuit IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 24 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.9 EDID programming using ENABLE_LDO IP4787CZ32 has a special mode providing an internal 5 V supply to the connector side power supply. This special mode allows programming of an Extended Display Identification Data Programmable Read-Only Memory (EDID PROM) placed on DDC bus between the device and the HDMI connector. The EDID programming mode can be utilized by driving an active HIGH signal to the ENABLE_LDO input pin. This enables an internal 5 V Low DropOut (LDO) to provide the supply on VCC(5V0) to HDMI_5V0_CON pin in case no higher supply is available at this pin. An active LOW input to ENABLE_LDO disables the EDID programming mode. 9.10 Backdrive protection The HDMI connector contains various signals which can partly supply current into an HDMI device that is powered down. Typically, the DDC lines and the CEC signals can force significant current back into the powered-down rails as shown in Figure 27, causing power-on reset problems with the system, and possible damage. The IP4787CZ32 prevents this backdrive condition whenever the I/O voltage is greater than the local supply. supply off 5V HDMI source HDMI sink backdrive current HDMI ASIC I2C-bus ASIC 018aaa109 Fig 27. Generalized backdrive protection IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 25 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.11 Schematic view of application Only a single external component (CO = 1 F) is required to protect and interface the ASIC to a complete and compliant HDMI port. The 100 nF ESD bypass capacitor is optional. &(& & 9WR96833/< $&7,9( &(&B6<6 9WR9 6833/< (6' E\SDVV RSWLRQDO 9'' Q) +'0, &211(&725 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B'B6<6 70'6B'B&21 70'6B&.B6<6 70'6B&.B&21 70'6B&.B6<6 70'6B&.B&21 &(&B&21 ,3&= ''&B&/.B6<6 ''&B&/.B&21 ''&B'$7B6<6 ''&B'$7B&21 +273/8*B&75/ +273/8*B&21 (1$%/(B/'2 +'0,B9B&21 &2 +'0, $6,& ) 3$' 87,/,7<B&21 DDD Fig 28. Schematic view of IP4787CZ32 application IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 26 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 9.12 Typical application The IP4787CZ32 is designed to simplify routing to the HDMI connector, and ease the incorporation of high-level ESD protection into delicately balanced high-speed TMDS lines. These lines rely on tightly controlled microstrip or stripline transmission lines with minimal impedance discontinuities, which can deteriorate return loss, increase deterministic jitter and generally erode overall link signal integrity. Normally, when designing a PCB with standard shunt ESD clamps, careful consideration must be given to manual pre-compensation of the additional load of the added ESD component. With the IP4787CZ32 TLCs, the ESD suppressor is designed to maintain the characteristic impedance of the PCB microstrip or stripline. Therefore the designer has to be concerned only with the standard-controlled impedance of the unloaded PCB lines. This simplifies the task of the PCB designer, and minimizes the tuning cycles, which are sometimes required when pre-compensation misses the mark. A basic application diagram for the ESD protection of an HDMI interface is shown in Figure 29 for a type-A HDMI connector. The optimized HVQFN32 pinning simplifies the PCB design to keep the ESD protection close to the connector where it can minimize the coupling of the ESD pulse onto other lines in the system during a strike. Due to the integrated pull-up and pull-down resistors, only two external capacitors are required to implement a fully compliant HDMI port. PP DDD Fig 29. Application of the IP4787CZ32 showing optimized HDMI type-A connector routing IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 27 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 10. Package outline HVQFN32: plastic thermal enhanced very thin quad flat package; no leads; 32 terminals; body 5 x 5 x 0.85 mm D B SOT617-3 A terminal 1 index area A A1 E detail X C e1 e 9 y1 C C A B C v w 1/2 e b y 16 L 17 8 e e2 Eh 1/2 e 24 1 terminal 1 index area 32 25 X Dh 0 2.5 Dimensions Unit(1) mm 5 mm scale A(1) A1 b max 0.05 0.30 nom 0.85 min 0.00 0.18 c D(1) Dh E(1) Eh 5.1 3.75 5.1 3.75 0.2 4.9 3.45 4.9 e e1 e2 0.5 3.5 3.5 L v w y y1 0.5 0.1 0.05 0.05 0.1 0.3 3.45 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. Outline version SOT617-3 References IEC JEDEC JEITA sot617-3_po European projection Issue date 11-06-14 11-06-21 MO-220 Fig 30. Package outline SOT617-3 (HVQFN32) IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 28 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 11. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 "Surface mount reflow soldering description". 11.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 11.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: * Through-hole components * Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: * * * * * * Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 11.3 Wave soldering Key characteristics in wave soldering are: * Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave * Solder bath specifications, including temperature and impurities IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 29 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 11.4 Reflow soldering Key characteristics in reflow soldering are: * Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 31) than a SnPb process, thus reducing the process window * Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board * Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 11 and 12 Table 11. SnPb eutectic process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 12. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 31. IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 30 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 31. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 "Surface mount reflow soldering description". 12. Glossary HDMI sink -- Device which receives HDMI signals for example, a TV set. HDMI source -- Device which transmits HDMI signal for example, DVD player. IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 31 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 13. Revision history Table 13. Revision history Document ID Release date Data sheet status Change notice Supersedes IP4787CZ32 v.3 20141219 Product data sheet - IP4787CZ32 v.2 Modifications: * Added support for HDMI 2.0 display modes and updated ESD robustness IP4787CZ32 v.2 20121220 Product data sheet - IP4787CZ32 v.1 IP4787CZ32 v.1 20120730 Preliminary data sheet - - IP4787CZ32 IP4787CZ32 All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 32 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 14. Legal information 14.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 14.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 14.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. IP4787CZ32 Product data sheet Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 33 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Quick reference data -- The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. Translations -- A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 14.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 15. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com IP4787CZ32 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 3 -- 19 December 2014 (c) NXP Semiconductors N.V. 2015. All rights reserved. 34 of 35 IP4787CZ32 NXP Semiconductors DVI and HDMI interface ESD and overcurrent protection 16. Contents 1 1.1 1.2 1.3 2 2.1 2.2 3 4 5 6 7 8 8.1 8.2 9 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 9.10 9.11 9.12 10 11 11.1 11.2 11.3 11.4 12 13 14 14.1 14.2 14.3 14.4 15 16 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General description . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Ordering information . . . . . . . . . . . . . . . . . . . . . 4 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 5 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6 Static characteristics. . . . . . . . . . . . . . . . . . . . . 7 Dynamic characteristics . . . . . . . . . . . . . . . . . 11 AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . 17 DDC propagation delay . . . . . . . . . . . . . . . . . 17 DDC transition time . . . . . . . . . . . . . . . . . . . . 18 Application information. . . . . . . . . . . . . . . . . . 19 HDMI connector side ESD protection . . . . . . . 19 TMDS ESD protection concept. . . . . . . . . . . . 19 Operating and standby modes . . . . . . . . . . . . 20 DDC circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 CEC circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Logic low I2C voltage shifter . . . . . . . . . . . . . . 23 Hot plug circuit . . . . . . . . . . . . . . . . . . . . . . . . 24 HEAC support and utility pin. . . . . . . . . . . . . . 24 EDID programming using ENABLE_LDO. . . . 25 Backdrive protection . . . . . . . . . . . . . . . . . . . . 25 Schematic view of application . . . . . . . . . . . . 26 Typical application . . . . . . . . . . . . . . . . . . . . . 27 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 28 Soldering of SMD packages . . . . . . . . . . . . . . 29 Introduction to soldering . . . . . . . . . . . . . . . . . 29 Wave and reflow soldering . . . . . . . . . . . . . . . 29 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 29 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 30 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 32 Legal information. . . . . . . . . . . . . . . . . . . . . . . 33 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 33 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Contact information. . . . . . . . . . . . . . . . . . . . . 34 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP Semiconductors N.V. 2015. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 19 December 2014 Document identifier: IP4787CZ32