SF2314E * Low-loss 866.5 MHz SAW Filter * Designed for 50 ohm Source/Load * Complies with Directive 2002/95/EC (RoHS) 866.5 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units +18 dBm 3 V Operable Temperature Range -45 to +125 C Specification Temperature Range -40 to +85 C Storage Temperature Range in Tape and Reel -40 to +85 C 265 C Input Power Level DC Voltage on any Non-ground Terminal Maximum Soldering Profile, 5 cycles/10 seconds maximum SM3030-6 Electrical Characteristics Characteristic Sym Center Frequency fC Notes Min 866.5 Insertion Loss, 863 to 870 MHz IL 2.3 3.0 dB 0.3 1.3 dBP-P 1.2:1 2.0:1 Amplitude Ripple, 863 to 870 MHz VSWR, 863 to 870 MHz Typ Max Units MHz Attenuation, Referenced to 0 dB: 10 to 830 MHz 45 49 830 to 850 MHz 22 35 885 to 905 MHz 27 35 905 to 950 MHz 45 49 950 to 1500 MHz 40 47 1500 to 3000 MHz 25 28 dB Source Impedance ZS 50 Load Impedance ZL 50 Case Style SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator Standard Reel Quantity A71, YWWS Reel Size 7 inch 500 Pieces/Reel Reel Size 13 inch 3000 Pieces/Reel Electrical Connections Connection Input Terminals 2 Output 5 Case Ground All others CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd. Copyright (c) Murata Manufacturing Co., Ltd. All rights reserved. February 2015 SF2314E (R) 8/10/17 Page 1 of 5 www.murata.com Filter Response Plots Copyright (c) Murata Manufacturing Co., Ltd. All rights reserved. February 2015 SF2314E (R) 8/10/17 Page 2 of 5 www.murata.com Filter SWR Plots Copyright (c) Murata Manufacturing Co., Ltd. All rights reserved. February 2015 SF2314E (R) 8/10/17 Page 3 of 5 www.murata.com SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension A B C D E F G H I J K L M N O K L N K N mm Nom 3.00 3.00 1.25 0.90 2.80 1.60 0.85 1.50 0.60 1.30 3.20 1.70 1.05 0.81 0.38 Min 2.87 2.87 1.12 0.77 2.67 1.47 0.72 1.37 0.47 1.17 Max 3.13 3.13 1.38 1.03 2.93 1.73 0.98 1.63 0.73 1.43 Inches Nom 0.118 0.118 0.049 0.035 0.110 0.063 0.033 0.059 0.024 0.051 0.126 0.067 0.041 0.032 0.015 Min 0.113 0.113 0.044 0.030 0.105 0.058 0.028 0.054 0.019 0.046 Max 0.123 0.123 0.054 0.040 0.115 0.068 0.038 0.064 0.029 0.056 Case Materials O Materials N M M PCB Footprint Top View Solder Pad Plating 0.3 to 1.0 m Gold over 1.27 to 8.89 m Nickel Lid Plating 2.0 to 3.0 m Nickel Body Al2O3 Ceramic Pb Free TOP VIEW BOTTOM VIEW B 6 1 3 A71 YWWS A 2 G C 5 E 4 D Copyright (c) Murata Manufacturing Co., Ltd. All rights reserved. February 2015 SF2314E (R) 8/10/17 Page 4 of 5 F H 6 1 5 2 4 3 I J www.murata.com "B" millimeters Inches "B" REF. 100 REF. Tape and Reel Specifications Quantity Per Reel 7 178 500 13 330 3000 See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao Bo Ko Pitch W 2.0 4.0 PIN #1 A 1.50 1.75 0.3 0.05 3.35 mm 3.35 mm 1.40 mm 8.0 mm 12.0 mm Bo B Ao 12.0 5.5 RO.3 (MAX.) B Pitch A Ko R0.5 (MAX.) 1.5 SECTION A-A SECTION B-B Copyright (c) Murata Manufacturing Co., Ltd. All rights reserved. February 2015 SF2314E (R) 8/10/17 Page 5 of 5 USER DIRECTION OF FEED www.murata.com