15TC65-50 - SENSATA TECHNOLOGIES

TNPU e3

www.vishay.com Vishay Draloric

Revision: 01-Jul-16 1Document Number: 28779

For technical questions, contact: thinfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Ultra Precision Thin Film Chip Resistors

TNPU e3 ultra precision thin film flat chip resistors combine

the proven reliability of TNPW e3 products with a most

advanced level of precision and stability. This unique

combination makes the product perfectly suited for all

applications with outstanding requirements towards size,

reliable precision and stability.

FEATURES

• Low temperature coefficient and tight

tolerances

• Sulfur resistance verified according to ASTM

B 809

• Superior moisture resistivity (85 °C; 85 % RH)

• Excellent overall stability at different environmental

conditions  0.05 % (1000 h rated power at 70 °C)

• AEC-Q200 qualified

• Material categorization: for definitions of compliance

please see www.vishay.com/doc?99912

APPLICATIONS

• Industrial equipment

• Telecommunication

• Medical equipment

• Instrumentation

• Test and measuring equipment

• Automotive

Note

(1) Please refer to APPLICATION INFORMATION, see below.

APPLICATION INFORMATION

When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal

resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted

film temperature is not exceeded.

These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift

increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a

functional lifetime.

TECHNICAL SPECIFICATIONS

DESCRIPTION TNPU0603 e3 TNPU0805 e3 TNPU1206 e3

Imperial size 0603 0805 1206

Metric size code RR1608M RR2012M RR3216M

Resistance range 100  to 100 k100  to 332 k100  to 511 k

Resistance tolerance ± 0.1 %; ± 0.05 %; ± 0.02 %

Temperature coefficient ± 10 ppm/K; ± 5 ppm/K

Rated dissipation, P70 (1) 0.1 W 0.125 W 0.25 W

Operating voltage, Umax. ACRMS/DC 75 V 150 V 200 V

Permissible film temperature,



F max. (1) 125 °C 125 °C 125 °C

Operating temperature range -55 °C to 125 °C -55 °C to 125 °C -55 °C to 125 °C

Permissible voltage against ambient

(insulation):

1 min; Uins 100 V 200 V 300 V

FITobserved  0.1 x 10-9/h  0.1 x 10-9/h  0.1 x 10-9/h

TNPU e3

www.vishay.com Vishay Draloric

Revision: 01-Jul-16 2Document Number: 28779

For technical questions, contact: thinfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

MAXIMUM RESISTANCE CHANGE AT RATED DISSIPATION

OPERATION MODE STANDARD

Rated dissipation, P70

TNPU0603 e3 0.100 W

TNPU0805 e3 0.125 W

TNPU1206 e3 0.250 W

Operating temperature range -55 °C to 125 °C

Permissible film temperature,



F max. 125 °C

Max. resistance change at P70 for resistance range,

|R/R| after:

TNPU0603 e3 100  to 100 k

TNPU0805 e3 100  to 332 k

TNPU1206 e3 100  to 511 k

1000 h  0.05 %

8000 h  0.1 %

225 000 h  0.3 %

TEMPERATURE COEFFICIENT AND RESISTANCE RANGE

TYPE / SIZE TCR TOLERANCE RESISTANCE E-SERIES

TNPU0603 e3

± 10 ppm/K ± 0.05 %

100  to 100 k

E24; E192

± 5 ppm/K

± 0.1 %

± 0.05 %

± 0.02 %

TNPU0805 e3

± 10 ppm/K ± 0.05 %

100  to 332 k

± 5 ppm/K

± 0.1 %

± 0.05 %

± 0.02 % 100  to 200 k

TNPU1206 e3

± 10 ppm/K ± 0.05 %

100  to 511 k

± 5 ppm/K

± 0.1 %

± 0.05 %

± 0.02 % 100  to 200 k

TNPU e3

www.vishay.com Vishay Draloric

Revision: 01-Jul-16 3Document Number: 28779

For technical questions, contact: thinfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

• Products can be ordered using either the PART NUMBER or the PRODUCT DESCRIPTION.

PACKAGING

TYPE / SIZE CODE QUANTITY PACKAGING STYLE WIDTH PITCH PACKAGING

DIMENSIONS

TNPU0603 e3

TNPU0805 e3

TNPU1206 e3

E52 = EN 1000 Tape and reel

cardboard tape

acc. IEC 60286-3,

Type 1a

8 mm 4 mm Ø 180 mm / 7"

ET1 = EA 5000

PART NUMBER AND PRODUCT DESCRIPTION

Part Number: TNPU12061K32AZEA00

TYPE / SIZE RESISTANCE TOLERANCE TCR PACKAGING

TNPU0603

TNPU0805

TNPU1206

R = Decimal

K = Thousand

M = Million

(4 digits)

B = ± 0.1 %

A = ± 0.05 %

H = ± 0.02 %

Y = ± 10 ppm/K

Z = ± 5 ppm/K

Product Description: TNPU1206 1K32 0.05 % T-16 ET1 e3

TNPU1206 1K32 0.05 % T-16 ET1 e3

TYPE / SIZE RESISTANCE TOLERANCE TCR PACKAGING LEAD (Pb)-FREE

TNPU0603

TNPU0805

TNPU1206

Examples:

1K32 = 1320 

± 0.1 %

± 0.02 %

± 0.05 %

T-13 = ± 10 ppm/K

T-16 = ± 5 ppm/K

ET1

E52

e3 = Pure tin

termination finish

NPU12061KT2AZEA003

TNPU e3

www.vishay.com Vishay Draloric

Revision: 01-Jul-16 4Document Number: 28779

For technical questions, contact: thinfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

DESCRIPTION

Production is strictly controlled and follows an extensive

set of instructions established for reproducibility. A

homogeneous film of metal alloy is deposited on a high

grade AI2O3 ceramic substrate and conditioned to achieve

the desired temperature coefficient. Specially designed

inner contacts are deposited on both sides. A special laser

is used to achieve the target value by smoothly fine trimming

the resistive layer without damaging the ceramics. A further

conditioning is applied in order to stabilize the trimming

result. The resistor elements are covered by a protective

coating designed for electrical, mechanical and climatic

protection. The terminations receive a final pure tin on nickel

plating. The result of the determined production is verified

by an extensive testing procedure on 100 % of the individual

chip resistors. Only accepted products are laid directly into

the tape in accordance with IEC 60286-3 Type 1a (1).

ASSEMBLY

The resistors are suitable for processing on automatic

SMD assembly systems. They are suitable for automatic

soldering using wave, reflow or vapour phase as shown in

IEC 61760-1 (1). The encapsulation is resistant to all

cleaning solvents commonly used in the electronics

industry, including alcohols, esters and aqueous solutions.

The suitability of conformal coatings, potting compounds

and their processes, if applied, shall be qualified by

appropriate means to ensure the long-term stability of the

whole system.

The resistors are RoHS compliant, the pure tin plating

provides compatibility with lead (Pb)-free and

lead-containing soldering processes. The immunity of the

plating against tin whisker growth has been proven under

extensive testing.

MATERIALS

Vishay acknowledges the following systems for the

regulation of hazardous substances:

• IEC 62474, Material Declaration for Products of and for the

Electrotechnical Industry, with the list of declarable

substances given therein (2)

• The Global Automotive Declarable Substance List

(GADSL) (3)

• The REACH regulation (1907/2006/EC) and the related list

of substances with very high concern (SVHC) (4) for its

supply chain

The products do not contain any of the banned substances

as per IEC 62474, GADSL, or the SVHC list, see

www.vishay.com/how/leadfree.

Hence the products fully comply with the following

directives:

• 2000/53/EC End-of-Life Vehicle Directive (ELV) and

Annex II (ELV II)

• 2011/65/EU Restriction of the Use of Hazardous

Substances Directive (RoHS) with amendment

2015/863/EU

• 2012/19/EU Waste Electrical and Electronic Equipment

Directive (WEEE)

Vishay pursues the elimination of conflict minerals from its

supply chain, see the Conflict Minerals Policy at

www.vishay.com/doc?49037.

RELATED PRODUCTS

For products with precision specification see the datasheet:

• TNPW e3 - High Stability Thin Film Flat Chip Resistors

(www.vishay.com/doc?28758)

Notes

(1) The quoted IEC standards are also released as EN standards with the same number and identical contents.

(2) The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474.

(3) The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council and available at

www.gadsl.org.

(4) The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table.

TNPU e3

www.vishay.com Vishay Draloric

Revision: 01-Jul-16 5Document Number: 28779

For technical questions, contact: thinfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

FUNCTIONAL PERFORMANCE

Derating

120

100

Ambient Temperature in °C

Rated Power in %

-55 -25 0 25 50 75 100 125 150 175

110

100

Non-Linearity

A ytiraeniL-noN 3Bd ni

Resistance Value in Ω

TNPU0603 e3

TNPU1206 e3

TNPU0805 e3

1K 10K 100K 1M

100 1K 10K 100K 1M

Current Noise

Current Noise in

µV/V

Resistance Value in Ω

TNPU0805

0.1

0.01

TNPU0603

TNPU1206

TNPU e3

www.vishay.com Vishay Draloric

Revision: 01-Jul-16 6Document Number: 28779

For technical questions, contact: thinfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TEST AND REQUIREMENTS

All tests are carried out in accordance with the following

specifications:

EN 60115-1, generic specification

EN 60115-8 (successor of EN 140400),

sectional specification

EN 140401-801, detail specification

IEC 60068-2-xx, test methods

The parameters stated in the Test Procedures and

Requirements table are based on the required tests and

permitted limits of EN 140401-801. The table presents only

the most important tests, for the full test schedule refer to

the documents listed above. However, some additional

tests and a number of improvements against those

minimum requirements have been included.

The testing also covers most of the requirements specified

by EIA / ECA-703 and JIS-C-5201-1.

The tests are carried out under standard atmospheric

conditions in accordance with IEC 60068-1, 4.3, whereupon

the following values are applied:

Temperature: 15 °C to 35 °C

Relative humidity: 25 % to 75 %

Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).

A climatic category LCT / UCT / 56 is applied, defined by the

lower category temperature (LCT), the upper category

temperature (UCT), and the duration of exposure in the

damp heat, steady state test (56 days).

The components are mounted for testing on printed circuit

boards in accordance with EN 60115-8, 2.4.2, unless

otherwise specified.

TEST PROCEDURES AND REQUIREMENTS

EN 60115-1

CLAUSE

IEC 60068-2 (1)

TEST METHOD TEST PROCEDURE REQUIREMENTS

PERMISSIBLE CHANGE (R)

Stability for product types:

TNPU0603 e3

TNPU0805 e3

TNPU1206 e3

4.5 - Resistance ± 0.1 %; ± 0.05 %; ± 0.02 %

4.8 - Temperature

coefficient

At (20 / -55 / 20) °C

and (20 / 125 / 20) °C ± 10 ppm/K; ± 5 ppm/K

4.25.1 - Endurance at 70 °C

U = or U = Umax.;

whichever is the less severe;

1.5 h on; 0.5 h off;

70 °C; 1000 h ± (0.05 % R + 0.01 )

70 °C; 8000 h ± (0.1 % R + 0.02 )

4.25.3 - Endurance at upper

category temperature

125 °C; 1000 h ± (0.05 % R + 0.01 )

125 °C; 8000 h ± (0.1 % R + 0.02 )

4.24 78 (Cab) Damp heat,

steady state

(40 ± 2) °C; 56 days;

(93 ± 3) % RH ± (0.1 % R + 0.01 )

4.23 Climatic sequence:

± (0.1 % R + 0.02 )

4.23.2 2 (Bb) Dry heat UCT; 16 h

4.23.3 30 (Db) Damp heat, cyclic

55 °C; 24 h;

> 90 % RH;

5 cycle

4.23.4 1 (Ab) Cold LCT; 2 h

4.23.5 13 (M) Low air pressure 8.5 kPa; 2 h; (25 ± 10) °C

4.23.6 30 (Db) Damp heat, cyclic

55 °C; 24 h;

> 90 % RH;

5 cycles

4.23.7 - D.c. load

U = Umax.; 1 min

LCT = -55 °C

UCT = 125 °C

- 1 (Aa) Cold -55 °C; 2 h ± (0.05 % R + 0.01 )

P70 x R

TNPU e3

www.vishay.com Vishay Draloric

Revision: 01-Jul-16 7Document Number: 28779

For technical questions, contact: thinfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

(1) The quoted IEC standards are also released as EN standards with the same number and identical contents.

4.19 14 (Na) Rapid change

of temperature

30 min at LCT and

30 min at UCT;

LCT = -55 °C;

UCT = 125 °C;

1000 cycles

± (0.1 % R + 0.01 )

4.13 - Short time

overload

U = 2.5 x

or U = 2 x Umax.;

whichever is the less severe;

5 s

± (0.05 % R + 0.01 )

4.22 6 (Fc) Vibration

Endurance by sweeping;

10 Hz to 2000 Hz;

no resonance;

amplitude  1.5 mm or

 200 m/s2; 6 h

± (0.05 % R + 0.01 )

no visible damage

4.17 58 (Td) Solderability

Solder bath method;

SnPb40; non-activated flux

(215 ± 3) °C; (3 ± 0.3) s Good tinning ( 95 % covered);

no visible damage

Solder bath method;

SnAg3Cu0,5 or SnAg3,5;

non-activated flux

(235 ± 3) °C; (2 ± 0.2) s

4.18 58 (Td) Resistance to

soldering heat

Solder bath method;

(260 ± 5) °C; (10 ± 1) s ± (0.02 % R + 0.01)

4.29 45 (XA) Component solvent

resistance

Isopropyl alcohol

+50 °C; method 2 No visible damage

4.32 21 (Ue3) Shear (adhesion)

RR 1608M; 9 N

No visible damage

RR 2012M and

RR 3216M; 45 N

4.33 21 (Ue1) Substrate bending Depth 2 mm, 3 times ± (0.05 % R + 0.01)

no visible damage, no open circuit in bent position

4.7 - Voltage proof URMS = Uins; 60 ± 5 s No flashover or breakdown

4.35 - Flammability IEC 60 695-11-5 (1),

needle flame test; 10 s No burning after 30 s

4.39 -

Periodic electric

overload:

Standard operation

mode

U =

or U = 2 x Umax.;

whichever is the less severe;

0.1 s on; 2.5 s off;

1000 cycles

± (0.1 R + 0.02 )

4.37 67 (Cy)

Damp heat,

steady state,

accelerated

(85 ± 5) °C; 56 days

(85 ± 5) % RH ± (0.25 R + 0.05 )

4.38 -

Electro static

discharge

(Human Body Model)

IEC 61340-3-1 (1);

3 pos. + 3 neg.

(equivalent to MIL-STD-883,

method 3015)

TNPU0603: 1000 V

TNPU0805: 1500 V

TNPU1206: 2000 V

± (0.5 R + 0.05 )

TEST PROCEDURES AND REQUIREMENTS

EN 60115-1

CLAUSE

IEC 60068-2 (1)

TEST METHOD TEST PROCEDURE REQUIREMENTS

PERMISSIBLE CHANGE (R)

Stability for product types:

TNPU0603 e3

TNPU0805 e3

TNPU1206 e3

P70 x R

15 x P70 x R

TNPU e3

www.vishay.com Vishay Draloric

Revision: 01-Jul-16 8Document Number: 28779

For technical questions, contact: thinfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

DIMENSIONS

SOLDER PAD DIMENSIONS

DIMENSIONS AND MASS

TYPE / SIZE H

(mm)

MASS

(mg)

TNPU0603 e3 0.45 ± 0.10 1.6 ± 0.10 0.85 ± 0.10 0.3 ± 0.20 0.3 ± 0.20 2

TNPU0805 e3 0.45 ± 0.10 2.0 ± 0.15 1.25 ± 0.15 0.4 ± 0.20 0.4 ± 0.20 5.5

TNPU1206 e3 0.55 ± 0.10 3.2 ± 0.15 1.6 ± 0.15 0.5 ± 0.25 0.5 ± 0.25 10

RECOMMENDED SOLDER PAD DIMENSIONS

TYPE / SIZE

REFLOW SOLDERING WAVE SOLDERING

(mm)

TNPU0603 e3 0.5 0.9 1.0 0.9 0.9 1.0

TNPU0805 e3 0.7 1.3 1.2 0.9 1.3 1.3

TNPU1206 e3 0.9 1.7 2.0 1.1 1.7 2.3

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 08-Feb-17 1Document Number: 91000

Disclaimer



ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.