LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features * Side looking special for LCD backlight. * Package in 8mm tape on 7" diameter reels. * Compatible with automatic placement equipment. * Compatible with infrared and vapor phase reflow solder process. * EIA STD package. * I.C. compatible. Package Dimensions Part no. LTST-S110TBKT-AD Lens Water Clear Source Color InGaN Blue Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.10 mm (.004") unless otherwise noted. Part No. : LTST-S110TBKT-AD BNS- D-C131/A4 Page : 1 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Absolute Maximum Ratings At Ta=25 Parameter LTST-S110TBKT-AD Unit Power Dissipation 120 mW Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) 100 mA Continuous Forward Current 20 mA Derating Linear From 25 0.25 mA/ 5 V 300 V Reverse Voltage Electrostatic Discharge Threshold(HBM)Note A Operating Temperature Range -20C to + 80C Storage Temperature Range -30C to + 100C Wave Soldering Condition 260C For 5 Seconds Infrared Soldering Condition 260C For 5 Seconds Vapor Phase Soldering Condition 215C For 3 Minutes Note A : HBM : Human Body Model. Seller gives no other assurances regarding the ability of to withstand ESD. Suggest IR Reflow Condition : Part No. : LTST-S110TBKT-AD BNS-OD-C131/A4 Page : 2 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Electrical Optical Characteristics At Ta=25 Parameter Symbol Luminous Intensity Part No. LTST- Min. Typ. Max. Unit Test Condition 45.0 - 71.0 mcd IF = 20mA Note 1 IV S110TBKT-AD Viewing Angle 21/2 S110TBKT-AD 130 deg Note 2 (Fig.6) Peak Emission Wavelength Peak S110TBKT-AD 468 nm Measurement @Peak (Fig.1) Dominant Wavelength d S110TBKT-AD nm IF = 20mA Note 3 Spectral Line Half-Width S110TBKT-AD Forward Voltage VF S110TBKT-AD Reverse Current IR S110TBKT-AD 470 - 475 25 2.9 - nm 3.5 V IF = 20mA 100 A VR = 5V Notes: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength, d is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 4. Caution in ESD: Static Electricity and surge damages the LED. It is recommend to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. Part No. : LTST-S110TBKT-AD BNS-OD-C131/A4 Page : 3 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Bin Code List Forward Voltage Unit: V @20mA Bin Code Min. Max. 12 2.90 3.00 13 3.00 3.10 14 3.10 3.20 15 3.20 3.30 16 3.30 3.40 17 3.40 3.50 Tolerance on each Forward Voltage bin is +/-0.1 volt Luminous Intensity Unit : mcd @20mA Bin Code Min. Max. P1 45.0 56.0 P2 56.0 71.0 Tolerance on each Intensity bin is +/-15% Dominant Wavelength Unit : nm @20mA Bin Code Min. Max. 1AD 470.0 472.5 2AD 472.5 475.0 Tolerance for each Dominate Wavelength bin is +/- 1nm Part No. : LTST-S110TBKT-AD BNS-OD-C131/A4 Page : 4 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Typical (25 Electrical Ambient Part No. : LTST-S110TBKT-AD BNS-OD-C131/A4 / Optical Characteristics Curves Temperature Unless Otherwise Noted) Page : 5 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Cleaning Do not use unspecified chemical liquid to clean LED they could harm the package. If clean is necessary, immerse the LED in ethyl alcohol or in isopropyl alcohol at normal temperature for less one minute. Suggest Soldering Pad Dimensions Package Dimensions Of Tape And Reel Notes: 1. All dimensions are in millimeters (inches). Part No. : LTST-S110TBKT-AD BNS-OD-C131/A4 Page : 6 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Notes: 1. Empty component pockets sealed with top cover tape. 2. 7 inch reel-3000 pieces per reel. 3. Minimum packing quantity is 500 pcs for remainders. 4. The maximum number of consecutive missing lamps is two. 5. In accordance with ANSI/EIA 481-1-A-1994 specifications. Part No. : LTST-S110TBKT-AD BNS-OD-C131/A4 Page : 7 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only CAUTIONS 1. Application limitation The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household application.) Consult Liteon's sales in advance for information on application in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as airplanes, automobiles, traffic control equipment, life support system and safety devices). 2. Storage After opening the package. The LEDs should be kept at 30C or less and 70%RH or less. The LEDs should be soldered within 168 hours(7 days) after opening the package. If unused LEDs remain, they should be stored in moisture proof package, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. If LEDs have exceeded the storage time, baking treatment should be performed with 605C more than 24 hours. Please avoid rapid transitions in ambient temperature in high humidity environments where condensation may occur. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. 4. Soldering Do not apply any stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering condition Reflow soldering Soldering iron Temperature 300C Max. Pre-heat 120~150C Pre-heat time 120 sec. Max. Soldering time 3 sec. Max. (one time only) Peak temperature 240C Max. Soldering time 10 sec. Max. Wave soldering Pre-heat Pre-heat time Solder wave Soldering time 100C Max. 60 sec. Max. 260C Max. 10 sec. Max. 5. Drive Method LED is a current operated device, and therefore, requires some kind of current limiting incorporated into the drive circuit. This current limiting typically takes the form of a current limiter resistor placed in series with the LED. Consider worst case voltage variations that could occur across the current limiting resistor. The forward current should not be allowed to change by more than 40% of its desired value. Circuit model A LED Circuit model B LED (A) Recommended circuit. (B) The difference of brightness between LEDs could be found due to the Vf-If characteristics of LED. Part No. : LTST-S110TBKT-AD BNS-OD-C131/A4 Page : 8 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 6. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Use of a conductive wrist band or antielectrostatic glove is recommended when handling these LED. All devices, equipment and machinery must be properly grounded. 7. Reliability Test Classification Test Item Referance Standard Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 1000HRS (-24HRS,+72HRS)*@20mA. MIL-STD-750D:1026 (1995) MIL-STD-883D:1005 (1991) JIS C 7021:B-1 (1982) High Temperature High Humidity Storage IR-Reflow In-Board, 2 Times Ta= 655,RH= 9095% *Test Time= 240HRS2HRS MIL-STD-202F:103B(1980) JIS C 7021:B-11(1982) High Temperature Storage Ta= 1055 *Test Time= 1000HRS (-24HRS,+72HRS) MIL-STD-883D:1008 (1991) JIS C 7021:B-10 (1982) Low Temperature Storage Ta= -555 *Test Time=1000HRS (-24HRS,+72H RS) JIS C 7021:B-12 (1982) 105 25 -55 25 30mins 5mins 30mins 5mins 10 Cycles MIL-STD-202F:107D (1980) MIL-STD-750D:1051(1995) MIL-STD-883D:1010 (1991) JIS C 7021:A-4(1982) IR-Reflow In-Board, 2 Times 105 5 -55 5 10mins 10mins 10 Cycles MIL-STD-202F:107D(1980) MIL-STD-750D:1051(1995) MIL-STD-883D:1011 (1991) Solder Resistance T.sol= 260 5 Dwell Time= 10 1secs MIL-STD-202F:210A(1980) MIL-STD-750D:2031(1995) JIS C 7021:A-1(1982) IR-Reflow Ramp-up rate(183 to Peak) +3 second max Temp. maintain at 125(25) 120 seconds max Temp. maintain above 183 60-150 seconds Peak temperature range 235+5/-0 Time within 5C of actual Peak Temperature (tp) 10-30 seconds Ramp-down rate +6/second max MIL-STD-750D:2031.2(1995) J-STD-020(1999) T.sol= 235 5 Immersion time 20.5 sec Immersion rate 252.5 mm/sec Immersion rate 252.5 mm/sec Coverage 95% of the dipped surface MIL-STD-202F:208D(1980) MIL-STD-750D:2026(1995) MIL-STD-883D:2003(1991) IEC 68 Part 2-20 JIS C 7021:A-2(1982) Operation Life Endurance Test Test Condition Temperature Cycling Thermal Shock Environmental Test Solderability 8. Others The appearance and specifications of the product may be modified for improvement without notice. Part No. : LTST-S110TBKT-AD BNS-OD-C131/A4 Page : 9 of 9