The A8586 is a high frequency step-down switching regulator
with an integrated high-side power MOSFET. It provides up
3.5 A output current. The A8586 can achieve fast transient
response using current-mode control and simple external
compensation.
The wide input range of 3.8 to 36 V makes the A8586 suitable
for a wide range of step-down applications, including those in
an automotive input environment. Battery-driven applications
benefit from the low 30 μA operational quiescent current.
The A8586 maintains high efficiency across a wide load range
by the use of pulse-frequency modulation (PFM) as the load
reduces. This in turn reduces switching and gate driver losses
at light load. A8586-1 and A8586-2 are options that disable
the PFM function. A8586-1 also disables the dithering feature.
These can be useful when low output ripple and minimum
output capacitance is required.
Frequency foldback helps to prevent inductor current runaway
during startup and provides enhanced dropout performance.
Extensive protection features of the A8586 include pulse-by-
pulse current limit, hiccup mode short-circuit protection, open/
short freewheeling diode protection, BOOT open/short voltage
protection, VIN undervoltage lockout, and thermal shutdown.
The A8586 and A8586-2 are designed to aid in EMC/EMI
design by including frequency dithering, soft freewheel diode
turn-off, and well controlled switch node slew rates. A 4 MHz
oscillator allows the A8586 to switch outside EMI sensitive
frequencies bands such as the AM band or ADSL bands.
The A8586 is available in industry-standard DFN-10 or SOIC-8
packages.
A8586-DS, Rev. 7
MCO-0000142
Automotive AEC-Q100 qualified
Supply voltage from 3.8 to 36 V
Output voltage adjustable from 0.8 to 30 V
Maximized duty cycle for low dropout operation
Low 30 μA operational quiescent current
150 mΩ integrated MOSFET switch
Programmable switching frequency up to 4 MHz
Improved EMC with frequency dithering (A8586 and
A8586-2) and controlled switch node rise and fall times
Ceramic capacitor stable
Internal soft-start
Overcurrent protection
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
PACKAGES:
A8586 Simplied Schematic
A8586, A8586-1, A8586-2
VOUT
VI
N
CIN CZ
CP
Optional
BST
VIN
EN
COMP
SW
FB
FREQ
GND
RFREQ
D
LO
RFB1
RFB2
C
OUT
CBST
FEATURES AND BENEFITS DESCRIPTION
10-Pin DFN with Exposed
Thermal Pad (suffix EJ)
8-Pin SOIC with Exposed
Thermal Pad (suffix LJ)
Not to scale
APPLICATIONS
High-voltage power
conversion
Automotive systems
Industrial power system
Distributed power
systems
Battery-powered systems
Part Dither
Feature
PFM
Operation
A8586 Yes Yes
A8586-1 No No
A8586-2 Yes No
August 30, 2018
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
2
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
ABSOLUTE MAXIMUM RATINGS [2]
Characteristic Symbol Notes Rating Unit
Input Voltage VIN −0.3 to 40 V
Switch Node Voltage VSW
−0.3 to VIN + 0.3 V
t < 250 ns −1.5 V
t < 50 ns VIN + 3 V
Bootstrap Pin to Switch Node VBST-SW −0.3 to 6 V
EN, FREQ −0.3 to VIN + 0.3 V
All other pins −0.3 to 6 V
Junction Temperature TJ−40 to 150 °C
Storage Temperature Range Tstg −40 to 150 °C
[2] Stresses beyond those listed in this table may cause permanent damage to the device. The absolute maximum ratings are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the Electrical Characteristics table is not implied. Exposure to absolute-maximum-rated conditions
for extended periods may a󰀨ect device reliability.
SELECTION GUIDE
Part Number Package Packing [1]
A8586KLJTR-T 8-pin SOIC with thermal pad 3,000 pieces per 13-inch reel
A8586KEJTR-T 10-pin DFN with thermal pad 1,500 pieces per 7-inch reel
A8586KLJTR-T-1 8-pin SOIC with thermal pad 3,000 pieces per 13-inch reel
A8586KLJTR-T-2 8-pin SOIC with thermal pad 3,000 pieces per 13-inch reel
[1] Contact Allegro for additional packing options.
THERMAL CHARACTERISTICS: May require derating at maximum conditions; see application information
Characteristic Symbol Test Conditions [3] Value Unit
Junction-to-Ambient Thermal Resistance RθJA
DFN-10 (EJ) package on 4-layer PCB based on JEDEC standard 45
°C/W
SOIC-8 (LJ) package on 4-layer PCB based on JEDEC standard 35
[3] Additional thermal information available on the Allegro website.
SPECIFICATIONS
RECOMMENDED OPERATING CONDITIONS
Characteristic Symbol Test Conditions Value Unit
Input Voltage VIN 3.8 to 36 V
Junction Temperature TJ−40 to 150 °C
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
3
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
BST
SW
SW
COMP
GND
FB
FREQ
EN
VIN
VIN
LDO
VREG
VREG
VREG
BST
Boot
Charge
Dither
Generator
Osc PWM
Generator
Soft Start
Ramp
0.8 V
+
+
+
Functional Block Diagram
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
4
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
Terminal List Table
Pin
Name
Pin Number
Description
EJ
Package
LJ
Package
SW 1, 2 1
The source of the internal MOSFET. The output inductor (LO) and cathode of the freewheel diode (D) should be
connected to this pin. LO and D should be placed as close as possible to this pin and connected with relatively
wide traces.
EN 3 2 Enable input. This pin is a high-voltage input that turns the regulator on or off: Set this pin high to turn the regulator
on or set this pin low to turn the regulator off.
COMP 4 3
Output of the error amplifier and compensation node for the current-mode control loop. Connect a series RC
network from this pin to GND for loop compensation. See the Applications section of this datasheet for further
details
FB 5 4 Feedback (negative) input to the error amplifier. Connect a resistor divider from the regulator output node, VOUT,
to this pin to program the output voltage.
GND 6 5 Ground connection
FREQ 7 6 Frequency setting pin. A resistor, RFREQ, from this pin to GND sets the PWM switching frequency. See Table 1 and
Figure 2 to determine the value of RFREQ.
VIN 8, 9 7 Power input for the control circuits and the drain of the internal high-side N-channel MOSFET. Connect this pin to a
power supply of 3.8 to 36 V. A high quality ceramic capacitor should be placed very close to this pin and GND
BST 10 8 Bootstrap capacitor connection. Connect a 100 nF capacitor from this pin to the SW pin. The voltage on this
capacitor drives the internal MOSFET via the high side gate driver. A series BOOT resistor is not recommended.
SW
SW
EN
COMP
FB
BST
VIN
VIN
FREQ
GND
PAD
1
2
3
4
56
7
8
9
10
Package EJ Pinouts
SW
EN
COMP
FB
BST
VIN
FREQ
GND
PAD
1
2
3
4
6
5
7
8
Package LJ Pinouts
PINOUT DIAGRAMS AND TERMINAL LIST TABLE
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
5
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
ELECTRICAL CHARACTERISTICS [1]: Valid for VIN = 12 V, VEN = 2.5 V, VCOMP = 1.4 V, –40°C ≤ TJ ≤ 125°C,
typical values at TJ = 25°C, unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Unit
GENERAL SPECIFICATIONS
Operating Input Voltage VIN VEN ≥ 2.5 V 3.8 12 36 V
VIN UVLO Start VIN(START) VIN rising 2.6 3.0 3.4 V
VIN UVLO Hysteresis VIN(HYS) 0.4 V
Supply Quiescent Current [1] IQ
No load, VFB = 0.9 V, A8586 only,
–40°C ≤ TJ ≤ 65°C [2] 27 36 µA
IQ(SLEEP) VEN = 0 V 11 18 µA
PWM SWITCHING FREQUENCY
Switching Frequency fSW RFSET = 45 kΩ 1.6 2.0 2.4 MHz
THERMAL PROTECTION
Thermal Shutdown Threshold [2] TTSD TJ rising 170 °C
Thermal Shutdown Hysteresis [2] THYS 20 °C
PULSE-WIDTH MODULATION (PWM)
Minimum On-Time [2] tON(MIN) 80 160 ns
Minimum Off-Time [2] tOFF(MIN) 100 ns
INTERNAL MOSFET
MOSFET On Resistance RDS(on) VBOOT-SW = 5 V 150 mΩ
MOSFET Leakage [2] IFET(LKG) VEN = 0 V, VIN = 12 V, VSW = 0 V, TJ = 25°C 0.1 1 µA
ERROR AMPLIFIER
Feedback Voltage VFB
4.5 V ≤ VIN ≤ 36 V, TJ = 25°C [2] 0.786 0.792 0.803 V
4.5 V ≤ VIN ≤ 36 V, –40°C ≤ TJ ≤ 125°C 0.773 0.812 V
Error Amp Voltage Gain [2] AVOL 1000 V/V
Error Amp Transconductance [2] gmICOMP = ±3 µA 35 60 95 µA/V
Error Amp Min. Source Current IEA(SOURCE) VFB = 0.7 V –5 µA
Error Amp Min. Sink Current IEA(SINK) VFB = 0.9 V 5 µA
Low IQ Peak Current Threshold IPEAK(LO_IQ) 800 mA
SOFT-START
SS Ramp Time [2] tSS 0 V < VFB < 0.8 V 1.5 ms
CURRENT PROTECTION
Current Limit ILIM 4.0 5.5 A
COMP to Current Sense
Transductance [2] GCS 9 A/V
Slope Compensation SE(2MHz) Measured at fSW = 2 MHz 2.2 3.1 4.0 A/µs
LOGIC ENABLE
EN Threshold Rising VEN(H) VEN rising 1.2 1.5 1.85 V
EN Threshold Falling VEN(L) VEN falling 1.0 1.2 1.4 V
EN Hysteresis VEN(HYS) 300 mV
[1] For input and output current specications, negative current is dened as coming out of the node or pin (sourcing), positive current is dened as going into the node or
pin (sinking).
[2] Ensured by design and characterization, not production tested.
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
6
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
FUNCTIONAL DESCRIPTION
Overview
The A8586 is a PWM buck regulator that incorporates all the
control and protection circuitry necessary to satisfy a wide range
of low-voltage applications. The A8586 employs current-mode
control to provide fast transient response, simple compensation,
and excellent stability.
The features of the A8586 include a ±3% reference, an adjust-
able switching frequency, a transconductance error amplifier, an
enable input, integrated power MOSFET, fixed soft-start time,
and low-current sleep mode.
The protection features of the A8586 include undervoltage
lockout (UVLO), cycle-by-cycle overcurrent protection (OCP),
hiccup mode short-circuit protection (HIC), overvoltage protec-
tion (OVP), and thermal shutdown (TSD).
PWM Control
A high-speed PWM comparator, capable of pulse widths less
than 100 ns, is included in the A8586. The inverting input of the
comparator is connected to the output of the error amplifier. The
non-inverting input is connected to the current sense signal.
At the beginning of each PWM cycle, the PWM_CLK signal
sets the PWM flip-flop and the high-side MOSFET is turned
on. When the current sense signal rises above the error ampli-
fier voltage, the comparator resets the PWM flip-flop and the
high-side MOSFET is turned off. It remains off for at least 100 ns
before the next cycle can be initiated.
Low-IQ Pulse-Frequency Modulation (PFM)
Mode (A8586 only)
At light loads, the PFM comparator, which is connected to the
FB pin, modulates the frequency of the SW node to regulate the
output voltage with very high efficiency.
The reference for the PFM comparator is calibrated approxi-
mately 1% above the PWM regulation point. When the volt-
age at the internal FB point rises above the PFM comparator
threshold and peak inductor current falls below IPEAK(LO_IQ)
(800 mA) minus slope compensation, the device will enter PFM
coast mode, tri-stating the SW node and drawing extremely low
current from VIN. When voltage at the FB point falls below
the PFM comparator threshold, the device will fully power-up
after approximately a 2.5 μs delay and the high-side MOSFET is
repeatedly turned on, operating at the PWM switching frequency
until the voltage at the FB pin rises above the PFM comparator
threshold. VOUT will rise at a rate determined by—and have a
voltage ripple dependent on—the input voltage, output voltage,
inductor value, output capacitance, and load. In addition, the
transition point from PWM to PFM mode is defined by the input
voltage, output voltage, slope compensation, and inductor value.
Error Amplifier
The primary function of the transconductance error amplifier is
to regulate the A8586 output voltage. The error amplifier appears
as a device with three inputs: two positive and one negative. The
negative input is simply connected to the FB pin and is used to
sense the feedback voltage for regulation. The two positive inputs
are connected to the internal soft-start and reference voltages. The
error amplifier performs an analog OR selection between them;
it regulates to either the soft-start voltage or the A8586 internal
reference (VREF), whichever is lower.
To stabilize the regulator, a series RC compensation network (RZ
CZ) must be connected from the error amplifier output (COMP
pin) to GND as shown in the typical application schematic. In
most applications, an additional, low-value capacitor (CP) should
be connected in parallel with the RZ CZ compensation network
to roll-off the loop gain at higher frequencies. However, if the CP
capacitor is too large, the phase margin of the regulator may be
reduced.
During operation, the minimum COMP voltage is clamped to
750 mV and its maximum is clamped to 1.5 V. COMP is inter-
nally pulled down to GND during fault conditions.
Slope Compensation
The A8586 family incorporates internal slope compensation (SE)
to allow PWM duty cycles above 50% for a wide range of input/
output voltages and inductor values. The slope compensation sig-
nal is added to the sum of the current sense amplifier output and
the PWM ramp offset. The amount of slope compensation scales
with the maximum on-time (1/fSW – tOFF(MIN)) centered around
3.1 A/μs at 2 MHz. The value of the output inductor should be
chosen such that SE is between 0.5× and 1× the falling slope of
the inductor current (SF).
Internal Regulator
An internal series-pass regulator (LDO) generates around 2.9 V
for most of the internal circuits of the A8586. The power for this
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
7
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
LDO is derived from VIN. The LDO is in full regulation once VIN
is greater than 3.0 V.
Enable Control
The enable (EN) input provides enabling/disabling the A8586
with system control or enabling/disabling the A8586 automati-
cally. The EN pin is rated to 40 V, so this EN pin may be con-
nected directly to VIN if there is no suitable logic signal available
to wake up the regulator.
When EN is being used as a system controlled enabling/disabling
logic input and EN is kept high, the A8586 turns on and—pro-
vided there are no fault conditions—VOUT will ramp to its final
voltage in the soft-start time. When the EN is low, the A8586 will
enter shutdown mode and draw less than 20 μA from the input.
When EN transitions low, the device waits approximately 150 μs
before shutting down. This delay provides plenty of filtering
to prevent the device from prematurely entering Sleep mode
because of any small glitches that might couple onto the PCB
trace or EN pin.
The enable input can also be used as a programmable UVLO.
Connecting a resistor from VIN to enable and a second resistor
from enable to ground implements this feature.
A8586
VIN
EN
R1
R2
VIN(START) =
VIN(STOP) =
R1 + R2
R1 + R2
R2
R2
VEN(H)
VEN(L)
(1)
(2)
While there is an internal 1 μA current source that pulls EN up if
enable is not used, it is recommended to connect it to VIN so the
A8586 is automatically enabled once VIN exceeds VINSTART.
Undervoltage Lockout (UVLO)
An undervoltage lockout (UVLO) comparator monitors the volt-
age at the VIN pin and keeps the regulator disabled if the voltage
is below the lockout threshold (VIN(START)). The UVLO compara-
tor incorporates enough hysteresis (VIN(HYS)) to prevent on/off
cycling of the regulator due to IR drops in the VIN path during
heavy loading or during startup.
Low-Dropout Operation
The A8586 is designed to operate with one quarter the switching
frequency when an off-time of less than tOFF(MIN) is demanded.
Internal Soft-Start
Inrush current to the regulator is controlled by the soft-start func-
tion. When the A8586 is enabled, after all faults are cleared, the
soft-start will ramp upward from 0 to 0.8 V. The error amplifier
output slews upward and, shortly thereafter, PWM switching will
begin.
After the A8586 starts switching, the error amplifier will regulate
the voltage at the FB pin to the internal soft-start voltage. After
switching starts, the regulator output voltage will rise from 0 V
to the set point determined by the feedback resistor divider (RFB1
and RFB2). When the voltage of the internal soft-start reaches
0.8 V, the error amplifier will change mode and begin regulating
to the A8586 internal reference, 792 mV.
To keep the inductor current under control, the A8586 operates
with one quarter the switching frequency while VFB remains
below 200 mV, and half the switching frequency when VFB is
between 200 and 400 mV. The A8586 operates at the full switch-
ing frequency when VFB is greater than 400 mV.
Pre-Biased Startup
If the output of the regulator is pre-biased to some voltage, the
A8586 modifies the normal startup routine to prevent discharging
the output capacitors. As described previously, the error amplifier
usually becomes active when the soft-start voltage starts to ramp.
If the output is pre-biased, the internal FB voltage is at some non-
zero voltage. The COMP pin remains low and SW is tri-stated
until the soft-start voltage rises above VFB.
Thermal Shutdown
The A8586 protects itself from overheating by means of an
internal thermal monitoring circuit. If the junction temperature
exceeds the thermal shutdown threshold (TTSD, 170°C typi-
cal), the voltages at the soft-start and COMP pins will be pulled
to GND and the high-side MOSFET will be turned off. The
A8586 will automatically restart when the junction temperature
decreases more than the thermal shutdown hysteresis (THYS,
20°C typical).
MOSFET Driver and Bootstrap Capacitor
The position of the internal N-channel MOSFET requires special
consideration when driving it. The source of this MOSFET can be
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
8
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
either at close to VIN or close to GND. For that reason, a float-
ing gate charge driver is required. This driver requires a voltage
greater than VIN to ensure the MOSFET can be turned on.
A simple charge pump—consisting of an internal charge circuit,
an external capacitor (BST capacitor), and the freewheeling diode
—is required to power the high side gate driver. The internal
charge circuit is power by VIN. When the SW node is sufficiently
below VIN, the charge circuit will charge the BST capacitor to
around 5 V with respect to the SW node. This BST voltage is
used to turn the MOSFET on. As SW node rises, the BST capaci-
tor will maintain the BST pin at 5 V above SW, thereby ensuring
sufficient voltage to keep the MOSFET on.
Also, the BST charge circuit incorporates its own UVLO of 1.8 V
rising and 0.4 V hysteresis.
Current Comparator and Current Limit
A high-bandwidth current sense amplifier monitors the current
in the high-side MOSFET. The current signal is supplied to the
PWM comparator and the cycle-by-cycle current limiter.
The cycle-by-cycle maximum current of the internal power
MOSFET is internally limited.
Overcurrent Protection (OCP) and Hiccup Mode
An OCP counter and hiccup mode circuit protect the buck regula-
tor when the output of the regulator is shorted to ground or when
the load is too high. When the soft-start ramp is active (t < tSS),
the OCP hiccup counter is disabled. Two conditions must be met
for the OCP counter to be enabled and begin counting:
t > tSS, and
VCOMP clamped at its maximum voltage (OCL = 1)
As long as these two conditions are met, the OCP counter
remains enabled and counts pulses from the overcurrent compar-
ator. If the COMP voltage decreases (OCL = 0), the OCP counter
is cleared. If the OCP counter reaches the OCPLIM counts (120),
a hiccup latch is set and the COMP pin is quickly pulled down by
a relatively low resistance (4 kΩ). Switching is halted for 6 ms to
provide time for the IC to cool down. After the hiccup off-time
expires (6 ms), the soft-start ramp starts, marking the beginning
of a new, normal soft-start cycle as described earlier. When the
soft-start voltage crosses the effective output voltage, the error
amplifier forces the voltage at the COMP pin to quickly slew
upward and PWM switching resumes. If the short circuit at the
regulator output remains, another hiccup cycle occurs. Hiccups
repeat until the short circuit is removed or the converter is dis-
abled. If the short circuit has been removed, the device soft-starts
normally and the output voltage automatically recovers to the
target level.
7.20
6.80
6.40
6.00
5.60
5.20
4.80
4.40
4.00
3.60
3.20
2.80
01020304050 60 70 80 90 100
Duty Cycle (%)
Current Limit (A)
Min. 400 kHz Max. 400 kHzTyp. 400 kHz
Min. 2 MHz Max. 2 MHzTyp. 2 MHz
Figure 1: Current Limit vs. Duty Cycle
BOOT Capacitor Protection
The A8586 monitors the voltage across the BOOT capacitor to
detect if the capacitor is missing or short-circuited. If the BOOT
capacitor is missing, the regulator enters hiccup mode after
7 PWM cycles. If the BOOT capacitor is shorted, the regulator
enters hiccup mode after 120 PWM cycles. For a BOOT fault,
hiccup mode operates virtually the same as described previously
for an output short circuit fault (OCP), having a hiccup off time
of 6 ms followed by a soft start retry with repeated attempts until
the fault clears. However, OCP is the only fault that is ignored
during the soft start ramp time (tSS). BOOT faults are a non-
latched condition, so the device automatically recovers when the
fault is corrected.
Freewheeling Diode Protection
If the freewheeling diode is missing or damaged (open), the SW
pin is subject to unusually high negative voltages. This nega-
tive voltage may cause the device to malfunction and could lead
to damage. The A8586 includes protection circuitry to detect
when the freewheeling diode is missing. If the SW pin is below
−1.25 V typically, for more than 50 ns typically, the device enters
hiccup mode after detecting 1 missing diode fault. Also, if the
freewheeling diode is shorted, the device experiences extremely
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
9
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
high currents through the high-side MOSFET. If this occurs, the
device enters hiccup mode after detecting one shorted diode fault.
Overvoltage Protection (OVP)
The A8586 provides an always-on overvoltage protection that
monitors VOUT to protect against VOUT rising up at light loads
due to high side switch leakage. In this case, the high-side switch
is forced off and the low-side switch continues to operate and can
correct the OVP condition provided only a few milliamperes of
pull-down current are required. When the condition causing the
overvoltage is corrected, the regulator automatically recovers.
Pin-to-Ground and Pin-to-Pin Short Protec-
tions
The A8586 is designed to satisfy the most demanding automotive
applications. For example, the device is carefully designed funda-
mentally to withstand a short circuit to ground at each pin without
suffering damage. In addition, care was taken when defining the
device pin-out to optimize protection against adjacent pin-to-
pin short circuits. For example, logic pins and high-voltage pins
are separated as much as possible. Inevitably, some low-voltage
pins had to be located adjacent to high-voltage pins, but in
these instances the low-voltage pins are designed to withstand
increased voltages, with clamps and/or series input resistance, to
prevent damage to the device.
Startup and Shutdown
If both VIN and VEN are higher than their appropriate thresholds,
the chip starts. The reference block starts first, generating stable
reference voltage and currents, and then the internal regulator is
enabled. The regulator provides stable supply for the remaining
circuits.
When the internal soft-start block is enabled, it first holds its SS
output low to ensure the remaining circuits are ready and then
slowly ramps up.
Three events can shut down the chip: EN low, VIN low and ther-
mal shutdown. In the shutdown procedure, power MOSFET is
turned off first to avoid any fault triggering. The COMP voltage
and the internal supply rail are then pulled down.
Programmable Oscillator
A resistor (RFREQ) from FREQ to ground sets the operation
frequency of the A8586. The Applications Information section
details the selection of this resistor.
Frequency Dithering (A8586, A8586-2)
The A8586 and A8586-2 include a dithering function, which
changes the switching frequency within a certain frequency
range. By shifting the switching frequency of the regulator in a
triangle fashion around the programmed switching frequency, the
overall system noise magnitude can be greatly reduced.
The dithering sweep is internally set at ±8%. The switching
frequency will ramp from a low of 0.92 times the programmed
frequency to a high of 1.08 times the programmed frequency. The
rate or modulation at which the frequency sweeps is governed by
an internal 12 kHz triangle pattern.
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
10
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
APPLICATIONS INFORMATION
Setting the Switching Frequency
The switching frequency (fSW) of a regulator using the A8586
can be set using a resistor at the FREQ pin (RFREQ). The recom-
mended RFREQ value for various switching frequencies can be
obtained from either Table 1 or Figure 2 below:
Table 1: RFREQ vs. fSW
fSW (MHz) RFREQ (kΩ)
4.0 15.4
3.5 20.0
3.0 26.1
2.5 34.0
2.0 45.3
1.5 68.1
1.0 105
0.8 140
0.5 232
0.3 402
0.2 619
700
600
500
400
300
200
100
0
0 0.5 11.5 22.5 33.5 4
Switching Frequency (MHz)
R (kΩ)
FREQ
Figure 2: RFREQ vs. fSW
While the A8586 can switch at frequencies up to 4 MHz, care
must be taken when operating above 2 MHz. The minimum con-
trollable on-time for the A8586 is around 80 ns. This means that
at higher frequencies, high input, and low output voltages, pulse
skipping may be seen.
30
25
20
15
10
5
1.5 2.0 2.5. 3.0 3.5 4.0
Switching Frequency (MHz)
Maximum Input Voltage (V)
VOUT = 2.5 V
VOUT = 3.3 V
Figure 3: Recommended Switching Frequency vs.
Maximum Input Voltage
Setting the Output Voltage
Many output voltages can be programmed by the selection of the
right resistor pair, RFB1 and RFB2. These resistors form a voltage
divider between VOUT and GND with FB pin as the center. The
voltage divider divides the output voltage down to the feedback
voltage.
R
=
FB1
V
OUT
–V
FB
V
FB
× RFB2 (3)
Table 2 below shows some typical resistor values selected from
the E48 series for popular output voltages, using RFB2 = 40.2 kΩ.
More accurate output voltage set points can be achieved by using
a parallel combination for RFB1.
Table 2: RFB1 vs. VOUT, RFB2 = 40.2 kΩ
VOUT (V) RFB1 (kΩ)
1 10
1.2 20.5
1.5 34.8
1.8 51.1
2 59
2.5 86.6
2.7 95.3
3.3 127
5 215
12 562
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
11
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
Inductor
As with any buck converter, an inductor is required to supply
constant current to the output load while being driven by the
switched input voltage. Many factors determine the selection of
this inductor, such as switching frequency, output/input voltage
ratio, transient response, and ripple current. A larger value induc-
tor will result in less ripple current that will result in lower output
ripple voltage. However, the larger value inductor will have a
larger physical size, higher series resistance, and/or lower satura-
tion current.
A good rule for determining the inductance to use is to allow the
peak-to-peak ripple current in the inductor to be approximately
30% of the maximum output current (IOUTMAX). Also, make sure
that the peak inductor current during normal operation is below
the maximum switch current limit. The inductance value can be
calculated by:
(4)
L
=
O
VOUT VOUT
I
SW L
ΔVIN
1–
()
where VOUT is the output voltage, VIN is the input voltage, fSW
is the switching frequency, and ΔIL is the peak-to-peak inductor
ripple current = 0.3 × IOUTMAX.
A second constraint on inductor value would be loop stability
at duty cycles greater than 50%. The A8586 uses current-mode
control and includes internal slope compensation (SE). Based on
the SE value, recommended inductance for stability would be:
(5)
L
O
VOUT VIN(MIN)
SEVOUT
1–0.18 ×
()
Slope compensation (SE) will vary with switching frequency. SE
can be calculated using equation 6.
(6)
S=
EE(2MHz)
1
2 MHz 100 ns
1
fSW
100 ns
(
)
Choose an inductor that will not saturate under the maximum
inductor peak current, which is the current limit of the A8586,
over the full temperature range.
Also, ensure that the peak current at IOUTMAX does not exceed the
current limit. The peak inductor current can be calculated by:
(7)
I= I+
LPK OUTMAX
V
OUT
V
OUT
2 × L
SW O VIN
1–
()
Freewheeling Diode
The freewheeling diode allows the current in the inductor to flow
to the load when the high-side switch is off. To reduce losses due
to the diode forward voltage and recovery times, use a Schottky
diode.
Choose a diode with a maximum reverse voltage rating greater
than the maximum input voltage and a current rating greater than
the maximum load current.
Input Capacitor
Three factors should be considered when choosing the input
capacitors. First, they must be chosen to support the maximum
expected input voltage with adequate design margin. Second,
their rms current rating must be higher than the expected rms
input current to the regulator. Third, they must have enough
capacitance and a low enough ESR to limit the input voltage
dv/dt to something much less than the hysteresis of the VIN pin
UVLO circuitry (350 mV (typ)) at maximum loading and mini-
mum input voltage.
The input capacitor(s) must limit the voltage deviations at the
VIN pin to something significantly less than the A8586 VIN pin
UVLO hysteresis during maximum load and minimum input
voltage. The minimum input capacitance can be calculated as
follows:
(8)
CIN >
I
OUT
V
OUT
V
OUT
0.85 × f ×ΔVIN
SW VIN
VIN
1–
(
×
)
where ΔVIN is chosen to be much less than the hysteresis of the
VIN pin, UVLO comparator (ΔVIN ≤ 100 mV is recommended)
and fSW is the nominal PWM switching frequency.
For simplification, choose the input capacitor with an RMS cur-
rent rating greater than half of the maximum load current.
Output Capacitor
The output capacitors filter the output voltage to provide an
acceptable level of ripple voltage and they store energy to help
maintain voltage regulation during a load transient. The voltage
rating of the output capacitors must support the output voltage
with sufficient design margin.
The output voltage ripple (ΔVOUT) is a function of the output
capacitor parameters: COUT, ESR, and ESL:
(9)
ΔVOUT = Δ ESR +
L
ΔI
L
V
IN
– V
OUT
8f C
SW OUT
LO
× ESL+
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
12
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
where LO is the inductor value, ESR is the equivalent series
resistance of the output capacitor, and ESL is its equivalent series
inductance.
The type of output capacitors will determine which terms of
equation 9 are dominant. For ceramic output capacitors the ESR
and ESL are virtually zero, so the output voltage ripple will be
dominated by the third term of equation 10:
(9)
ΔVOUT =
ΔI
L
8f C
SW OUT
To reduce the voltage ripple of a design using ceramic output
capacitors, simply increase the total capacitance, reduce the
inductor current ripple (that is, increase the inductor value), or
increase the switching frequency.
For electrolytic output capacitors, the value of capacitance will be
relatively high, so the third term in equation 9 will be very small.
The output voltage ripple will be determined primarily by the
first two terms of equation 9.
(11)
ΔVOUT = ΔIL × ESR +
V
IN
–V
OUT
LO
× ESL
To reduce the voltage ripple of a design using electrolytic output
capacitors, simply decrease the equivalent ESR and ESL by using
a high(er) quality capacitor, add more capacitors in parallel, or
reduce the inductor current ripple (that is, increase the inductor
value).
The ESR of some electrolytic capacitors can be quite high,
therefore choose a quality capacitor that clearly documents the
ESR, or the total impedance, in the datasheet. Also, the ESR of
electrolytic capacitors usually increases significantly at cold tem-
peratures, by as much as 10×, which increases the output voltage
ripple and, in most cases, significantly reduces the stability of the
system.
The transient response of the regulator depends on the number
and type of output capacitors. In general, minimizing the ESR of
the output capacitance will result in a better transient response.
The ESR can be minimized by simply adding more capacitors in
parallel or by using higher quality capacitors. At the instant of a
fast load transient (di/dt), the output voltage will change by the
amount.
(12)
ΔVOUT = ΔIOUT × ESR +
di
dt
× ESL
After the load transient occurs, the output voltage will deviate
from its nominal value for a short time. This time will depend
on the system bandwidth, the output inductor value, and output
capacitance. Eventually, the error amplifier will bring the output
voltage back to its nominal value.
The speed at which the error amplifier will bring the output volt-
age back to its set point will depend mainly on the closed-loop
bandwidth of the system. A higher bandwidth usually results in a
shorter time to return to the nominal voltage. However, a higher
bandwidth system may be more difficult to obtain acceptable gain
and phase margins. Selection of the compensation components
(RZ, CZ, CP) are discussed in more detail in the Compensation
Components section of this datasheet.
Low-IQ PFM Output Voltage Ripple Calculation
(A8586 Only)
After choosing an output inductor and output capacitor(s), it is
important to calculate the output voltage ripple (ΔVOUT(PFM))
during Low-IQ PFM mode. With ceramic output capacitors, the
output voltage ripple in PWM mode is usually negligible, but that
is not the case during Low-IQ PFM mode.
The PFM mode comparator requires about 10 mV or greater of
voltage ripple on the VOUT pin and generates groups of pulses
to meet this requirement. However, if a single pulse results in a
voltage ripple greater than 10 mV, then the voltage ripple would
be dictated by that single pulse. To calculate the voltage ripple
from that single pulse, first the peak inductor current must be cal-
culated with slope compensation accounted for. The IPEAK(LO_IQ)
specification does not include slope compensation; therefore, the
peak inductor current operating point is calculated as follows:
(13)
I=
PEAK_L
I
PEAK(LO_IQ)
VIN –V
OUT
L
EO
1 +
Then, calculate the MOSFET on-time (tON(Q)) and freewheeling
diode on-time (tON(D)) (Figure 3). The on-time is defined as the
time it takes for the inductor current to reach IPEAK_L:
(14)
t=
ON(Q)
L
PEAK_L O
V–V– (R + L)
IN OUT PEAK_L DS(ON)HSO(DCR)
where RDS(on) is the on-resistance of the internal high-side MOS-
FET (150 mΩ typical) and LO(DCR) is the DC resistance of the
output inductor (LO). During this rising time interval, the length
of time for the inductor current to rise from 0 A to IOUT is:
(15)
t=
1
L
OUT O
V–V– (R + L)
IN OUT PEAK_L DS(ON)HSO(DCR)
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
13
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
The freewheeling diode on-time is defined as the time it takes for
the inductor current to decay from IPEAK_L to 0 A:
t=
ON(D)
L
PEAK_L O
V+ V
OUT F
(16)
During this falling time interval, the length of time for the induc-
tor current to fall from IOUT to 0 A is:
t=
2
L
OUT O
V+ V
OUT F
(17)
t
IPEAK(LO_IQ)
IOUT
t
VPP(LO_IQ)
t2
t1
tON(Q) tON(D)
IL
VOUT
Figure 4: Calculating the Output Ripple Voltage
in PFM Mode (A8586 Only)
Given the peak inductor current (IPEAK_L ) and the rise and fall
times (tON(Q) and tON(D)) for the inductor current, the output volt-
age ripple can be calculated for a signal pulse as follows:
(18)
V=
PP(LO_IQ)
I–I
PEAK_L OUT
2 × COUT
(t + t–t–t)
ON(Q) ON(D)1 2
If VPP(LO_IQ) is greater than the ~10 mV ripple that the PFM
comparator requires, then the output capacitance or inductor
can be adjusted to reduce the PFM mode voltage ripple. In PFM
mode, decreasing the inductor value reduces the PFM ripple, but
may negatively impact the PWM voltage ripple, maximum load
current in PWM mode, or change the mode of operation from
CCM to DCM.
If VPP(LO_IQ) is less than the ~10 mV requirement, the A8586
operates with multiple pulses at the PWM frequency to meet the
ripple requirement. The fixed frequency operation may result in
DCM or CCM operation during the multiple pulses.
Compensation Components
A8586 employs current-mode control for easy compensation
and fast transient response. The system stability and transient
response are controlled through the COMP pin. COMP pin is the
output of the internal transconductance error amplifier. A series
capacitor-resistor combination sets a pole-zero pair to control the
characteristics of the control system. The DC voltage gain, A
VDC,
of the feedback loop is given by:
(19)
A
=
VDC
V
OUT
V
FB
VOUT
I
OUT
×
CS VOL
where A
VOL is the error amplifier voltage gain, 1000 V/V and
GCS is the current sense transconductance, 9 A/V.
The system has two noteworthy poles. One is due to the compen-
sation capacitor (CZ) and the error amplifier output resistor. The
other is due to the output capacitor and the load resistor. These
poles are located at:
(20)
f=
P1
g
m
× C ×A
ZVOL
(21)
f=
P2
I
OUT
× VOUT
OUT
where gm is the error amplifier transconductance, 60 μA/V.
The system has one noteworthy zero. This is due to the compen-
sation capacitor (CZ) and the compensation resistor (RZ). This
zero is located at:
(22)
f=
Z
1
× C × R
ZZ
The system may have another zero, if the output capacitor has a
large capacitance and/or a high ESR value. The zero, due to the
ESR and capacitance of the output capacitor, is located at:
(23)
f=
Z
1
× C × ESR
OUT
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
14
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
In this case (as shown in the simplified schematic on page 1), a
third pole set by the optional compensation capacitor (CP) and the
compensation resistor (RZ) is used to compensate the effect of the
ESR zero on the loop gain. This pole is located at:
(24)
f=
P3
1
× C × R
PZ
The goal of compensation design is to shape the converter
transfer function to get a desired loop gain. The system crossover
frequency where the feedback loop has unity gain is impor-
tant. Lower crossover frequencies result in slower line and load
transient responses, while higher crossover frequencies could
cause the system to be unstable. A good rule of thumb is to set the
crossover frequency to approximately one tenth of the switching
frequency. Table 3 lists typical values of compensation com-
ponents for some standard output voltages with various output
ceramic capacitors and inductors. The values of the compensation
components have been optimized for fast transient responses and
good stability.
Table 3: Compensation Values for Typical Output Voltage/
Capacitor Combinations with fSW = 500 kHz
VOUT
(V)
LO
(µH)
COUT
(µF)
RZ
(kΩ)
CZ
(pF) CP
1.8 4.7 47 105 100 None
2.5 4.7 - 6.8 22 54.9 220 None
3.3 6.8 -10 22 68.1 220 None
5 15 - 22 22 100 150 None
12 22 - 33 22 147 150 None
To optimize the compensation components for conditions not
listed in Table 3, the following procedure can be used.
1. Choose the compensation resistor (RZ) to set the desired
crossover frequency (fC). Determine the RZ value by the fol-
lowing equation:
(25)
R
=
Z
G
mCSVFB
× f
OUT C
V
OUT
×
2. Choose the compensation capacitor (CZ) to achieve the
desired phase margin. For applications with typical inductor
values, setting the compensation zero (fZ1) below one fourth
of the crossover frequency provides sucient phase margin.
Determine the CZ value by the following equation:
(26)
C>
Z
4
× R × f
ZC
3. Determine if the second compensation capacitor (CP) is
required. It is required if the ESR zero of the output capacitor
is located at less than half of the switching frequency or the
following relationship is valid:
(27)
<
1f
SW
× C × ESR
OUT 2
If this is the case, then add the second compensation capaci-
tor (CP) to set the pole fP3 at the location of the ESR zero.
Determine the CP value by the equation:
(28)
C=
PRZ
ESR
OUT
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
15
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
0
10
20
30
40
50
60
70
80
90
100
0.1 1 10 100 1000
Eciency (%)
IOUT (mA)
5.0 VO, 500 kHz Eciency vs. IOUT at 8 VIN, 12 VIN, and 16 VIN
VIN = 8 V, with PFM
VIN = 12 V, with PFM
VIN = 16 V, with PFM
VIN = 8 V
VIN = 12 V
VIN = 16 V
A8586 Series Efficiency Comparisons at 500 kHz
5.0 VO, PFM vs. non PFM
3.3 VO, PFM vs. non PFM
0
10
20
30
40
50
60
70
80
90
100
0.1 1 10 100 1000
Eciency (%)
I
OUT
(mA)
3.3 VO, 500 kHz Eciency vs. IOUT at 8 VIN, 12 VIN, and 16 VIN
V
IN
= 8 V, with PFM
V
IN
= 12 V, with PFM
V
IN
= 16 V, with PFM
V
IN
= 8 V
V
IN
= 12 V
V
IN
= 16 V
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
16
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
Figure 5: Typical Buck Converter with Critical Paths/Loops Shown
BST
PAD
EN FB
COMPFREQ
VIN
VIN
SW
SW
A8586EJ
GND
U1 10
9
8
3
7
6
4
5
2
1
BST
SW
FB
COMP
GND
FREQ
EN
VIN
VIN
GND GND
VOUT
VOUT
C5
100 nF
R2
100 kΩ
R3
232 kΩ
R1
24.9 kΩ
C3
0.1 µF
C2
4.7 µF
C1
4.7 µF
C6
220 pF
C7
NU
D2
PDS540
R5
51.1 kΩ
R4
40.2 kΩ
R6
127 kΩ
C8
22 µF
L1
10 µH
2
4
1
3
PCB COMPONENT PLACEMENT AND ROUTING
A good PCB layout is critical if the A8586 is to provide clean,
stable output voltages. Follow these guidelines to ensure a good
PCB layout. Figure 5 shows a typical A8586-based schematic
with the critical power paths/loops. Figure 6 shows an example
PCB component placement and routing with the same critical
power paths/loops as shown in the schematic.
1. By far, the highest di/dt in the asynchronous buck regulator
occurs at the instant the high-side MOSFET turns on, and the
ceramic input capacitors through the high-side MOSFET and
into the asynchronous diode to ground must be minimized.
Ideally these components are all connected using only the
top metal layer (that is, do not use vias to other power/signal
layers).
2. When the high-side MOSFET is on, current ows from the
input supply and capacitors, through the high-side MOSFET,
into the load via the output inductor, and back to ground. This
loop should be minimized and have relatively wide traces.
3. When the high-side MOSFET is o, free-wheeling current
ows from ground, through the asynchronous diode, into the
load via the output inductor, and back to ground. This loop
should be minimized and have relatively wide traces.
4. The voltage on the SW node transitions from 0 V to VIN very
quickly and is the root cause of many noise issues. It is best
to place the asynchronous diode and output inductor close
to the A8586 to minimize the size of the SW polygon. Also,
keep low level analog signals (like FB and COMP) away
from the SW polygon.
5. Place the feedback resistor divider (R6 and R4) very close to
the FB pin. Ground this resistor divider as close as possible to
the A8586.
6. To have the highest output voltage accuracy, the output volt-
age sense trace (from VOUT to R6) should be connected as
close as possible to the load.
7. Place the compensation components (R5, C6, and C7) as
close as possible to the COMP pin. Place vias to the GND
plane as close as possible to these components.
8. Place the bootstrap capacitor (C5) near the BST pin and keep
the routing from this capacitor to the SW polygon as short as
possible.
9. When connecting the input and output ceramic capacitors,
use multiple vias to GND and place the vias as close as pos-
sible to the pads of the components.
10. To minimize PCB losses and improve system eciency, the
input and output traces should be as wide as possible and be
duplicated on multiple layers, if possible.
11. The thermal pad under the A8586 must connect to the GND
plane using multiple vias. More vias will ensure the lowest
junction temperature and highest eciency.
12. EMI/EMC issues are always a concern. Allegro recommends
having component locations for an RC snubber from SW to
ground. The resistor should be 1206 size and connected to
ground plane to aid thermal dissipation.
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
17
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
Figure 6: Example PCB Component Placement and Routing
LOOP 1 (RED)
At the instant the internal MOSFET turns on, Schottky diode D2,
which is very capacitive, must be very quickly shut off (only 5
to 15 ns of charging time). This spike of charging current must
come from the local input ceramic capacitor, C3. This spike of
current is quite large and will be an EMI/EMC issue if loop 1
(red) is not minimized. Therefore, the input capacitor C3 and
Schottky diode D1 must be placed be on the same (top) layer, be
located near each other, and be grounded at virtually the same
point on the PCB.
LOOP 2 (MAGENTA)
When the internal MOSFET is off, free-wheeling inductor current
must flow from ground through diode D2 (SW will be at –Vf ),
into the output inductor, out to the load and return via ground.
While the MOSFET is off, the voltage on the output capacitors
decreases. The output capacitors and Schottky diode D2 should
be placed on the same (top) layer, be located near each other, and
be sharing a good, low inductance ground connection.
LOOP 3 (BLUE)
When the MOSFET is on, current will flow from the input supply
and input capacitors through the output inductor and into the load
and the output capacitors. At this time the voltage on the output
capacitors increases.
LOOP 4 (GREEN)
When the MOSFET is turned on, gate current is sourced from the
boot capacitor C5. This current can have significant di/dt levels.
The loop created by the A8586 BST pin, C5 and A8586 SW pin
should be minimized.
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
18
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
PACKAGE OUTLINE DRAWING
For Reference Only Not for Tooling Use
(Reference DWG 2860)
Dimensions in millimeters –NOT TO SCALE
Exact case and lead configuration at supplier discretion within limits shown
10
10
2
1
2
1
A
A
B
D
C
B
1.64
2.38
0.30
1
10
0.50
0.85
3.10
C
C0.08
11XC
SEATING
PLANE
D
0.25+0.05
–0.07 0.05
0.00
2.38 NOM
1.65 NOM
0.5 BSC
0.2 REF
0.75 ±0.05
3.00 ±0.15
3.00 ±0.15
0.40 ±0.10
PCB Layout Reference View
Terminal #1 mark area
Exposed thermal pad (reference only, terminal #1 identifier appearance at supplier discretion)
Coplanarity includes exposed thermal pad and terminals
Reference land pattern layout (reference IPC7351 SON50P300X300X80-11WEED3M);
all pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to meet
application process requirements and PCB layout tolerances; when mounting on a
multilayer PCB, thermal vias at the exposed thermal pad land can improve thermal
dissipation (reference EIA/JEDEC Standard JESD51-5)
Figure 7: Package EJ, 10-Pin DFN with Exposed Thermal Pad
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
19
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
For Reference Only Not for Tooling Use
(Reference DWG-2869)
Dimensions in millimeters NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
3.30
2
1
8
C
1.27
5.602.41
1.75
0.65
2.41 NOM
3.30 NOM
C
1.27 BSC
A
B
C
B
21
8
C
SEATING
PLANE
C0.10
8X
0.25 BSC
1.04 REF
1.70 MAX
4.90 ±0.10
3.90 ±0.10 6.00 ±0.20
0.51
0.31 0.15
0.00
0.25
0.17
1.27
0.40
A
Branded Face SEATING PLANE
GAUGE PLANE
PCB Layout Reference View
Terminal #1 mark area
Exposed thermal pad (bottom surface)
Reference land pattern layout (reference IPC7351 SOIC127P600X175-9AM);
all pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary
to meet application process requirements and PCB layout tolerances; when
mounting on a multilayer PCB, thermal vias at the exposed thermal pad land
can improve thermal dissipation (reference EIA/JEDEC Standard JESD51-5)
Figure 8: Package LJ, 8-Pin SOIC with Exposed Thermal Pad
Wide Input Voltage, Adjustable Frequency,
3.5 Amp Buck Regulator
A8586, A8586-1,
A8586-2
20
Allegro MicroSystems, LLC
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
For the latest version of this document, visit our website:
www.allegromicro.com
Revision History
Number Date Description
December 2, 2014 Initial release.
1 March 29, 2016 Updated Selection Guide table (page 2); minor editorial changes.
2 August 19, 2016 Added PCB Component Placement and Routing section (pages 15-16).
3 October 4, 2016 Removed “Operating at Low Input Voltages” section (page 8 and 14).
4 January 17, 2017 Corrected EJ package outline drawing (page 17).
Updated bootstrap capacitor value (pages 4 and 15).
5 April 20, 2018 Added efficiency curves (page 15).
6 May 17, 2018 Updated Supply Quiescent Current test conditions (page 5).
7 August 30, 2018
Updated Supply Quiescent Current test conditions (page 5); added footnote to Supply Quiescent
Current test conditions, MOSFET Leakage characteristic, and Feedback Voltage test conditions
(page 5).
Copyright ©2018, Allegro MicroSystems, LLC
Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to
permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that
the information being relied upon is current.
Allegro’s products are not to be used in any devices or systems, including but not limited to life support devices or systems, in which a failure of
Allegro’s product can reasonably be expected to cause bodily harm.
The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its
use; nor for any infringement of patents or other rights of third parties which may result from its use.
Copies of this document are considered uncontrolled documents.