T2 Terminator-for SL™ Female Crimp Terminal
Doc No: ATS-639103300 Release Date: 08-13-07 UNCONTROLLED COPY Page 1 of 6
Revision: C Revision Date: 12-02-08
INSULATION
CRIMP
BRUSH
STRIP
LENGTH
BELL
MOUTH
CRIMP HEIGHT
BEND
DOWN
ROLLING
CONDUCTOR
CRIMP
TWISTING
CUT
-
OFF
TAB
SEAM
T2 Terminator Tooling
Specification Sheet
Order No. 63910-3300
FEATURES
It is ideally suited for mid-volume bench operations
This terminator can be installed in the TM42 and the TM40 press or Base Unit adapter for 3BF press
Quick punch removal with the push of a button for fast and easy tooling change
Track adjustment capabilities in the T2 Terminators for improved control of the bell mouth size and cutoff tab
length
T2 Terminator has standardized tooling with the Molex FineAdjust Applicator which will reduce your inventory
requirements
SCOPE
Products: SL™ Female Crimp Terminal, 32-36 AWG.
Wire Size Insulation Diameter Strip Length
Terminal Series No
Terminal Order No. AWG
mm² mm In. mm In.
016-02-0074
016-02-0085
70058-0084
70058 016-02-0084
016-02-0143
70058-4084 32-36
0.03-0.01
0.43-0.64
.017-.025
3.17-3.56
.125-.140
71851 016-02-1118
016-02-1120
016-02-1122
32-36
0.03-0.01
0.43-0.64
.017-.025
3.17-3.56
.125-.140
DEFINITION OF TERMS
The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope.
T2 Terminator-for SL™ Female Crimp Terminal
Doc No: ATS-639103300 Release Date: 08-13-07 UNCONTROLLED COPY Page 2 of 6
Revision: C Revision Date: 12-02-08
CRIMP SPECIFICATION
Cut-off Tab Max.
Bell mouth Front Rear Conductor Brush
Terminal Series No.
mm In. mm In. mm In. mm In.
70058 0.20-0.50 .008-.020 0.13 .005 .08 .003 0.00-1.00 .000-.039
71851 0.20-0.50 .008-.020 0.13 .005 .08 .003 0.00-1.00 .000-.039
Bend up Bend down Twist Roll Punch Width mm (Ref)
Conductor Insulation
Terminal Series No. Degree Degree mm In mm In
70058 3 3 3 8 0.90 .035 1.40 .055
71851 3 3 3 8 0.90 .035 1.40 .055
Seam
Seam shall not be open
and no wire allowed out
of the crimping area
After crimping, the conductor profile should measure the following.
Wire Size Crimp Height Pull Force Min.
Terminal Series No. AWG mm2 mm In. N Lb.
32 0.03 0.64-0.66 .025-.026 4.4 1.0
34 0.02 0.61-0.64 .024-.025 2.7 0.6
70058
36 0.01 0.61-0.64 .024-.025 1.8 0.4
32 0.03 0.64-0.66 .025-.026 4.4 1.0
34 0.02 0.61-0.64 .024-.025 2.7 0.6
71851
36 0.01 0.61-0.64 .024-.025 1.8 0.4
Pull Force should be measured with no influence from the insulation crimp.
The above specifications are guidelines to an optimum crimp.
T2 Terminator-for SL™ Female Crimp Terminal
Doc No: ATS-639103300 Release Date: 08-13-07 UNCONTROLLED COPY Page 3 of 6
Revision: C Revision Date: 12-02-08
PARTS LIST
T-Style Terminator 63910-3300
Item Order No Engineering No. Description Quantity
Perishable Tooling
63910-3370 63910-3370 Tool Kit (All “Y” Items) REF
1 63444-0914 63444-0914 Conductor Punch 1 Y
2 63445-0931 63445-0931 Conductor Anvil 1 Y
3 63446-1419 63446-1419 Insulation Punch 1 Y
4 63445-1425 63445-1425 Insulation Anvil 1 Y
5 63443-0003 63443-0003 Cut-Off Plunger 2 Y
6 63443-0012 63443-0012 Front Plunger Retainer 1 Y
7 63443-1402 63443-1402 Cut-off Die Blade 1 Y
8 63443-1002 63443-1002 Rear Plunger Retainer 1 Y
Other Components (REF 103150)
9 11-17-0022 1739-21 Hold Down Spring 1
10 11-18-4094 60709A111 Front Cover 1
11 11-24-1067 4996-4 Cut-Off Plunger Spring 2
12 11-24-1149 4996-37 Shank 1
13 11-40-4039 8302-5 Front Plunger Striker 1
14 11-40-4274 8331-8 Hold Down Blade 1
15 63443-0025 63443-0025 Dual Carrier Key 1
16 63443-0085 63443-0085 Wire Stop L-Bracket 1
17 63443-0090 63443-0090 Wire Stop 1
18 63443-2600 63443-2600 Front Spacer 1
19 63443-2205 63443-2205 5.00mm Coarse Spacer 1
20 63443-2306 63443-2306 3.30mm Fine Spacer 1
21 63443-6003 63443-6003 Rear Cover 1
22 63800-8502 63800-8502 Rear Plunger Striker 1
Frame
23 63800-8500 63800-8500 T2 Terminator 1
24 63860-2015 63860-2015 Drag Frame 1
Hardware
25 N/A N/A M3 by 6 Long SHCS 2**
26 N/A N/A M3 by 6 Long FHCS 1**
27 N/A N/A M4 by 6 Long SHCS 1**
28 N/A N/A M4 by 12 Long BHCS 2**
29 N/A N/A M4 by 14 Long SHCS 2**
30 N/A N/A M4 by 35 Long SHCS 1**
31 N/A N/A M4 by 50 Long SHCS 1**
32 N/A N/A M5 by 10 Long SHCS 1**
33 N/A N/A M5 by 12 Long SHCS 1**
34 N/A N/A #5-40 by 3/8” Long SHCS 1**
35 N/A N/A #10-32 by 3/8” Long BHCS 1**
** Available from an industrial supply company such as MSC (1-800-645-7270).
T2 Terminator-for SL™ Female Crimp Terminal
Doc No: ATS-639103300 Release Date: 08-13-07 UNCONTROLLED COPY Page 4 of 6
Revision: C Revision Date: 12-02-08
5
21
19
20
6
12
1
3
13
Figure 1
27
14
17
28
4
9
16
2
26
15
31
30
25
(2)
8
(2)
11
(2)
7
24
18
23
10
22
29
(2)
17
33
32
34
(2)
35
Assembly Drawing
T2 Terminator-for SL™ Female Crimp Terminal
Doc No: ATS-639103300 Release Date: 08-13-07 UNCONTROLLED COPY Page 5 of 6
Revision: C Revision Date: 12-02-08
NOTES
Depending on the press vintage a feed finger assembly is supplied with the T2 Terminator.
1. To remove the existing feed finger assembly loosens the M4 x 10 mm set screw in the feed lever.
2. Select T2 Feed finger assembly from Terminator box.
3. Insert a screwdriver into the slot behind the feed lever and force the feed arm spring to the right.
4. Slide the T2 feed finger shaft for TM42 (11-40-5307) or (11-40-0123) for TM40 /Base Unit into the feed lever
and to the left of the feed arm spring.
5. Release the feed arm spring.
6. Position feed finger for selected product. (Refer to Figure 5.1 in the T2 Manual).
11
-
40
-
0123
FEED FINGER ROD
11
-
40
-
0125
FEED ARM SPRING
11
-
40
-
5255
FEED FINGER
COTTER PIN
1/8” X .0295 DIA. WIRE
11
-
40
-
5307
FEED FINGER ROD
11
-
40
-
5255
FEED FINGER
11
-
40
-
0125
FEED ARM SPRING
COTTER PIN
1/8” X .0295 DIA. WIRE
FEED FINGER ASSEMBLY
FOR PRESS TM42
TM42 PRESS
TM40 PRESS AND
BASE UNIT AND ADAPTER
FEED FINGER ASSEMBLY
FOR PRESS TM40
Figure 2
T2 Terminator-for SL™ Female Crimp Terminal
Doc No: ATS-639103300 Release Date: 08-13-07 UNCONTROLLED COPY Page 6 of 6
Revision: C Revision Date: 12-02-08
NOTES
1. Molex recommends an extra perishable tooling kit be maintained at your facility.
2. Verify tooling alignment by manually cycling the press before crimping under power. Check that all screws are
tight.
3. Slugs, Terminals, Dirt and Oil should be kept clear of work area.
4. This Terminator should be only used in a Molex TM42, TM40, or 3BF Press with a Base Unit adaptor.
5. Wear safety glasses at all times.
6. For recommended maintenance refer to the TM40, TM42 Manual.
CAUTION: To prevent injury never operate this Terminator without the guards supplied with the press in
place. Reference the TM42 press manufacturer’s instruction manual.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and
tooling.
Americas Headquarters
Lisle, Illinois 60532 U.S.A.
1-800-78MOLEX
amerinfo@molex.com
Far East North Headquarters
Yamato, Kanagawa, Japan
81-462-65-2324
feninfo@molex.com
Far East South Headquarters
Jurong, Singapore
65-6-268-6868
fesinfo@molex.com
European Headquarters
Munich, Germany
49-89-413092-0
eurinfo@molex.com
Corporate Headquarters
2222 Wellington Ct.
Lisle, IL 60532 U.S.A.
630-969-4550
Fax: 630-969-1352
Visit our Web site at http://www.molex.com