DG406, DG407
FN3116 Rev 11.00 Page 5 of 15
October 1, 2013
Absolute Maximum Ratings Thermal Information
V+ to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V
GND to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
Digital Inputs, VS, VD (Note 6)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(V-) -2V to (V+) +2V or 20mA,
Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D
(Pulsed 1ms, 10% Duty Cycle Max) . . . . . . . . . . . . . . . . . . . . . . . . . 100mA
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Thermal Resistance (Typical, Note 5) JA (°C/W)
PDIP Package*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
*Pb-free PDIPs can be used for through-hole wave solder processing only.
They are not intended for use in Reflow solder processing applications.
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
5. JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
6. Signals on SX, DX, EN or AX exceeding V+ or V- are clamped by internal diodes. Limit diode current to maximum current ratings.
Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, VAL = 0.8V, VAH = 2.4V Unless Otherwise Specified. Bold-face limits
apply over the operating temperature range, -40°C to +85°C.
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 7, 12)
TYP
(Note 8)
MAX
(Notes 7, 12) UNITS
DYNAMIC CHARACTERISTICS
Transition Time, tTRANS (See Figure 3) 25 - 200 300 ns
Full - - 400 ns
Break-Before-Make Interval, tOPEN (See Figure 5) 25 25 50 - ns
Full 10 --ns
Enable Turn-ON Time, tON(EN) (See Figure 4) 25 - 150 200 ns
Full - - 400 ns
Enable Turn-OFF Time, tOFF(EN) 25 - 70 150 ns
Full - - 300 ns
Charge Injection, Q CL = 1nF, VS = 0V, RS = 025 - 40 - pC
OFF-Isolation, OIRR VEN = 0V, RL = 1k,
f = 100kHz (Note 11)
25 - -69 - dB
Logic Input Capacitance, CIN f = 1MHz 25 - 7 - pF
Source OFF Capacitance, CS(OFF) VEN = 0V, VS = 0V, f = 1MHz 25 - 8 - pF
Drain OFF Capacitance, CD(OFF) VEN = 0V, VD = 0V, f = 1MHz
DG406 25 - 160 - pF
DG407 25 - 80 - pF
Drain ON Capacitance, CD(ON) VEN = 5V, VD = 0V, f = 1MHz
DG406 25 - 180 - pF
DG407 25 - 90 - pF
DIGITAL INPUT CHARACTERISTICS
Logic High Input Voltage, VINH Full 2.4 --V
Logic Low Input Voltage, VINL Full --0.8 V
Logic High Input Current, IAH VA = 2.4V, 15V Full -1 -1µA
Logic Low Input Current, IAL VEN = 0V, 2.4V, VA = 0V Full -1 -1µA
ANALOG SWITCH CHARACTERISTICS
Drain-Source ON-Resistance, rDS(ON) VD = ±10V, IS = +10mA
(Note 9)
25 - 50 100
Full - - 125
rDS(ON) Matching Between Channels, rDS(ON) VD = 10V, -10V (Note 10) 25 - 5 - %