Dynamic Block Reed-Solomon Decoder User's Guide December 2010 IPUG52_01.6 Table of Contents Chapter 1. Introduction .......................................................................................................................... 4 Quick Facts ........................................................................................................................................................... 4 Features ................................................................................................................................................................ 8 Chapter 2. Functional Description ...................................................................................................... 10 Block Diagram..................................................................................................................................................... 10 General Description ............................................................................................................................................ 10 Field Polynomial......................................................................................................................................... 11 Generator Polynomial ................................................................................................................................ 11 Shortened Codes ....................................................................................................................................... 11 Systematic Decoder ................................................................................................................................... 11 Decoding Modes ........................................................................................................................................ 11 Functional Description......................................................................................................................................... 12 Syndrome Transform ................................................................................................................................. 13 Key Equation Solver................................................................................................................................... 13 Error Locator .............................................................................................................................................. 13 Error Magnitude Corrector ......................................................................................................................... 13 Control Unit ................................................................................................................................................ 13 Basis Conversion Modules......................................................................................................................... 13 Variable Block Size .................................................................................................................................... 13 Variable Check Symbols ............................................................................................................................ 14 Puncturing Pattern File Format ........................................................................................................................... 14 Default Field Polynomials........................................................................................................................... 14 Signal Descriptions ............................................................................................................................................. 15 Timing Specifications .......................................................................................................................................... 17 Chapter 3. Parameter Settings ............................................................................................................ 20 RS Decoder Configuration GUI........................................................................................................................... 21 Core Configuration ..................................................................................................................................... 21 RS Parameters........................................................................................................................................... 21 Check Symbols .......................................................................................................................................... 22 Block Size Type ......................................................................................................................................... 22 Puncturing .................................................................................................................................................. 22 Decoding Mode .......................................................................................................................................... 22 Memory Type ............................................................................................................................................. 22 Optional Ports ............................................................................................................................................ 23 Chapter 4. IP Core Generation............................................................................................................. 24 Licensing the IP Core.......................................................................................................................................... 24 Getting Started .................................................................................................................................................... 24 IPexpress-Created Files and Top Level Directory Structure............................................................................... 26 Instantiating the Core .......................................................................................................................................... 28 Running Functional Simulation ........................................................................................................................... 28 Synthesizing and Implementing the Core in a Top-Level Design ....................................................................... 28 Hardware Evaluation........................................................................................................................................... 29 Enabling Hardware Evaluation in Diamond................................................................................................ 29 Enabling Hardware Evaluation in ispLEVER.............................................................................................. 29 Updating/Regenerating the IP Core .................................................................................................................... 29 Regenerating an IP Core in Diamond ........................................................................................................ 29 Regenerating an IP Core in ispLEVER ...................................................................................................... 30 Chapter 5. Support Resources ............................................................................................................ 31 Lattice Technical Support.................................................................................................................................... 31 (c) 2010 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. IPUG52_01.6, December 2010 2 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Table of Contents Online Forums............................................................................................................................................ 31 Telephone Support Hotline ........................................................................................................................ 31 E-mail Support ........................................................................................................................................... 31 Local Support ............................................................................................................................................. 31 Internet ....................................................................................................................................................... 31 References.......................................................................................................................................................... 31 LatticeEC/ECP ........................................................................................................................................... 31 LatticeECP2M ............................................................................................................................................ 31 LatticeECP3 ............................................................................................................................................... 31 LatticeSC/M................................................................................................................................................ 32 LatticeXP.................................................................................................................................................... 32 LatticeXP2.................................................................................................................................................. 32 Related Information............................................................................................................................................. 32 Revision History .................................................................................................................................................. 32 Appendix A. Resource Utilization ....................................................................................................... 33 LatticeECP and LatticeEC FPGAs ...................................................................................................................... 34 Ordering Part Number................................................................................................................................ 34 LatticeECP2 and LatticeECP2S FPGAs ............................................................................................................. 34 Ordering Part Number................................................................................................................................ 34 LatticeECP2M and LatticeECP2MS FPGAs ....................................................................................................... 35 Ordering Part Number................................................................................................................................ 35 LatticeECP3 FPGAs............................................................................................................................................ 35 Ordering Part Number................................................................................................................................ 35 LatticeXP FPGAs ................................................................................................................................................ 36 Ordering Part Number................................................................................................................................ 36 LatticeXP2 FPGAs .............................................................................................................................................. 36 Ordering Part Number................................................................................................................................ 36 LatticeSC and LatticeSCM FPGAs ..................................................................................................................... 37 Ordering Part Number................................................................................................................................ 37 IPUG52_01.6, December 2010 3 Dynamic Block Reed-Solomon Decoder User's Guide Chapter 1: Introduction Reed-Solomon codes are widely used in various communications and storage applications for forward error correction. Reed-Solomon codes are well suited for burst error correction and are frequently used as outer codes in communication systems. A Reed-Solomon Decoder performs detection and correction of the encoded data at the receiver. Lattice's Dynamic Block Reed-Solomon Decoder (RS Decoder) IP core is compliant with several industry standards including the more recent IEEE 802.16-2004 and can be custom configured to support other non-standard applications as well. The RS Decoder supports a wide range of symbol widths and allows the user to define the field polynomial, generator polynomial and several other parameters. The newer standards like IEEE 802.16-2004 require the use of Reed-Solomon codes with dynamically varying block sizes. Lattice's RS Decoder IP core provides an ideal solution that meets such needs of today's forward error correction world. This core allows the block size and number of check symbols to be varied dynamically through input ports. Lattice's RS Decoder IP can be used with Lattice's RS Decoder for a complete Reed-Solomon code based forward error correction application. For more information on these and other IP products for forward error correction, refer to the Lattice web site at www.latticesemi.com/products/intellectualproperty. Quick Facts Table 1-1 through Table 1-9 give quick facts about the RS Decoder IP core for LatticeECTM, LatticeECPTM, LattceECP2TM, LattticeSCTM, LatticeSCMTM, LatticeXPTM, LatticeECP2MTM, LatticeXP2TM, and LatticeECP3TM devices. Table 1-1. RS Decoder IP core for LatticeEC Devices Quick Facts RS Decoder IP Configuration OC-192 Core Requirements CCSDS Minimal Device Needed LUTs sysMEM EBRs Registers LFEC1E LFEC3E Synthesis LFEC3E LFEC3E LFEC3E 1100 2000 1200 1500 1900 2100 2 2 2 2 3 3 900 1500 900 1100 1400 1600 (R) Lattice DiamondTM 1.0 or ispLEVER 8.1 Synopsys(R) SynplifyTM Pro for Lattice D-2009.12L-1 Aldec(R) Active-HDLTM 8.2 Lattice Edition Simulation IPUG52_01.6, December 2010 LFEC1E LFEC20E-5F672C Lattice Implementation Design Tool Support ATSC IEEE 802.162004 SC LatticeEC Targeted Device Resource Utilization DVB FPGA Families Supported IEEE 802.162004 SCa/OFDM Mentor Graphics(R) ModelSimTM SE 6.3F 4 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Introduction Table 1-2. RS Decoder IP core for LatticeECP Devices Quick Facts RS Decoder IP Configuration OC-192 Core Requirements CCSDS LUTs sysMEM EBRs IEEE 802.162004 SC LatticeECP Minimal Device Needed Registers LFECP6E LFECP20E-5F672C 1100 2000 1200 1500 1900 2100 2 2 2 2 3 3 900 1500 900 1100 1400 1600 Lattice Implementation Design Tool Support ATSC FPGA Families Supported Targeted Device Resource Utilization DVB IEEE 802.162004 SCa/OFDM Lattice Diamond 1.0 or ispLEVER 8.1 Synthesis Synopsys Synplify Pro for Lattice D-2009.12L-1 Aldec Active-HDL 8.2 Lattice Edition Simulation Mentor Graphics ModelSim SE 6.3F Table 1-3. RS Decoder IP core for LatticeECP2 Devices Quick Facts RS Decoder IP Configuration OC-192 Core Requirements CCSDS FPGA Families Supported Minimal Device Needed LUTs sysMEM EBRs Registers LFE2-6E LFE2-50E-7F672C 1100 2000 1200 1500 1800 2100 2 2 2 2 3 3 900 1500 900 1100 1400 1600 Lattice Implementation Design Tool Support ATSC Synthesis Lattice Diamond 1.0 or ispLEVER 8.1 Synopsys Synplify Pro for Lattice D-2009.12L-1 Aldec Active-HDL 8.2 Lattice Edition Simulation IPUG52_01.6, December 2010 IEEE 802.162004 SC LatticeECP2 Targeted Device Resource Utilization DVB IEEE 802.162004 SCa/OFDM Mentor Graphics ModelSim SE 6.3F 5 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Introduction Table 1-4. RS Decoder IP core for LatticeSC Devices Quick Facts RS Decoder IP Configuration OC-192 Core Requirements CCSDS FPGA Families Supported LUTs sysMEM EBRs Registers 1900 2200 LFSC3GA15E LFSC3GA25E-7F900C 1200 2000 1200 1600 2 2 2 2 3 3 900 1500 900 1000 1400 1600 Lattice Implementation Design Tool Support ATSC IEEE 802.162004 SC LatticeSC Minimal Device Needed Targeted Device Resource Utilization DVB IEEE 802.162004 SCa/OFDM Lattice Diamond 1.0 or ispLEVER 8.1 Synthesis Synopsys Synplify Pro for Lattice D-2009.12L-1 Aldec Active-HDL 8.2 Lattice Edition Simulation Mentor Graphics ModelSim SE 6.3F Table 1-5. RS Decoder IP core for LatticeSCM Devices Quick Facts RS Decoder IP Configuration OC-192 Core Requirements CCSDS FPGA Families Supported LUTs sysMEM EBRs Registers LFSCM3GA15EP1 LFSCM3GA25EP1-7F900C 1200 2000 Synthesis 1600 1900 2200 2 2 2 2 3 3 1500 900 1000 1400 1600 Lattice Diamond 1.0 or ispLEVER 8.1 Synopsys Synplify Pro for Lattice D-2009.12L-1 Aldec Active-HDL 8.2 Lattice Edition Simulation IPUG52_01.6, December 2010 1200 900 Lattice Implementation Design Tool Support ATSC IEEE 802.162004 SC Lattice SCM Minimal Device Needed Targeted Device Resource Utilization DVB IEEE 802.162004 SCa/OFDM Mentor Graphics ModelSim SE 6.3F 6 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Introduction Table 1-6. RS Decoder IP core for LatticeXP Devices Quick Facts RS Decoder IP Configuration OC-192 Core Requirements CCSDS LUTs sysMEM EBRs IEEE 802.162004 SC 1900 2100 Lattice XP Minimal Device Needed Registers LFXP3E LFXP20E-5F484C 1100 2000 1200 1500 2 2 2 2 3 3 900 1500 900 1100 1400 1600 Lattice Implementation Design Tool Support ATSC FPGA Families Supported Targeted Device Resource Utilization DVB IEEE 802.162004 SCa/OFDM Lattice Diamond 1.0 or ispLEVER 8.1 Synthesis Synopsys Synplify Pro for Lattice D-2009.12L-1 Aldec Active-HDL 8.2 Lattice Edition Simulation Mentor Graphics ModelSim SE 6.3F Table 1-7. RS Decoder IP core for LatticeECP2M Devices Quick Facts RS Decoderr IP Configuration OC-192 Core Requirements CCSDS FPGA Families Supported LUTs sysMEM EBRs Registers Synthesis 2100 LFE2M35E-7F484C 1100 2000 1200 1500 2 2 2 2 3 3 900 1500 900 1100 1400 1600 Lattice Diamond 1.0 or ispLEVER 8.1 Synopsys Synplify Pro for Lattice D-2009.12L-1 Aldec Active-HDL 8.2 Lattice Edition Simulation IPUG52_01.6, December 2010 1800 LFE2M20E Lattice Implementation Design Tool Support ATSC IEEE 802.162004 SC Lattice ECP2M Minimal Device Needed Targeted Device Resource Utilization DVB IEEE 802.162004 SCa/OFDM Mentor Graphics ModelSim SE 6.3F 7 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Introduction Table 1-8. RS Decoder IP core for LatticeXP2 Devices Quick Facts RS Decoder IP Configuration OC-192 Core Requirements CCSDS DVB FPGA Families Supported Lattice XP2 Minimal Device Needed LFXP2-5E Targeted Device Resource Utilization LUTs sysMEM EBRs Registers IEEE 802.162004 SC LFXP2-17E-7FT256C 1100 2000 1200 1500 1800 2100 2 2 2 2 3 3 900 1500 900 1100 1400 1600 Lattice Implementation Design Tool Support ATSC IEEE 802.162004 SCa/OFDM Lattice Diamond 1.0 or ispLEVER 8.1 Synthesis Synopsys Synplify Pro for Lattice D-2009.12L-1 Aldec Active-HDL 8.2 Lattice Edition Simulation Mentor Graphics ModelSim SE 6.3F Table 1-9. RS Decoder IP core for LatticeECP3 Devices Quick Facts RS Decoder IP Configuration OC-192 Core Requirements CCSDS FPGA Families Supported LUTs sysMEM EBRs Registers Synthesis 1800 2100 LFE3-35EA LFE3-95E-8FN672CES 1100 2000 1200 1500 2 2 2 2 3 3 900 1500 900 1100 1400 1600 Lattice Implementation Design Tool Support ATSC IEEE 802.162004 SC Lattice ECP3 Minimal Device Needed Targeted Device Resource Utilization DVB IEEE 802.162004 SCa/OFDM Lattice Diamond 1.0 or ispLEVER 8.1 Synopsys Synplify Pro for Lattice D-2009.12L-1 Aldec Active-HDL 8.2 Lattice Edition Simulation Mentor Graphics ModelSim SE 6.3F Features * 3- to 12-Bit Symbol Width * Configurable Field Polynomial * Configurable Generator Polynomial: Starting Root and Root Spacing * User-defined Codewords - Maximum of 4095 symbols - Maximum of 256 check symbols - Shortened codes * Off-the-shelf Support for the Following Communication Standards: - OC-192 - DVB IPUG52_01.6, December 2010 8 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor - - - - Introduction CCSDS ATSC IEEE 802.16-2004 WirelessMAN-SCa/OFDM IEEE 802.16-2004 WirelessMAN-SC * Fully Synchronous * Systematic Decoder * Full Handshaking Capability * Dynamically Variable Block Size * Dynamically Variable Check Symbols * Error, Erasure and Puncturing Modes * Error Measurement Information IPUG52_01.6, December 2010 9 Dynamic Block Reed-Solomon Decoder User's Guide Chapter 2: Functional Description A block diagram of the RS Decoder is shown in Figure 2-1. The RS Decoder IP is comprised of the Syndrome Transform, Key Equation Solver, Error Locator, Error Magnitude Corrector, Data Memory and Output Processing blocks. Block Diagram Figure 2-1. RS Decoder Block Diagram Control Bus Error Magnitude Corrector Syndrome Transform din Key Equation Solver Error Locator Output Processing Unit dout ddel Data Memory clk rstn ibstart ce sr ers blocksize obstart obend outvalid errfnd Control rfi rfib fail numchks puncsel errcnt erscnt General Description Reed-Solomon codes are used to perform Forward Error Correction (FEC). FEC introduces controlled redundancy in the data before it is transmitted to allow error correction at the receiver. The redundant data (check symbols) are transmitted with the original data to the receiver. An RS Decoder is used in the receiver to correct any transmission errors. This type of error correction is widely used in data communications applications such as Digital Video Broadcasting (DVB) and Optical Carriers (i.e. OC-192). Reed-Solomon codes are written in the format RS(n,k) where k is the number of information symbols and n is the total number of symbols in a codeword or block. Each symbol in the codeword is wsymb bits wide. The RS Decoder performs detection and correction of encoded data available at the receiver after demodulation. The RS encoded data is then processed to determine whether any errors have occurred during transmission. Once the number of IPUG52_01.6, December 2010 10 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Functional Description errors is determined, the decoder decides if they are within the range of correction. After determining this, the decoder corrects the errors in the received data. A typical application of space signal processing is shown in Figure 2-2. Figure 2-2. Application of Reed-Solomon Code in a Space Communication System Input Data RS Encoder Interleaver Convolutional Encoder Decoded Data RS Decoder Deinterleaver Viterbi Decoder Transmitted Data Received Data Reed-Solomon codes are defined on a finite field known as Galois field. The size of the field is determined by the symbol width, wsymb, and is equal to 2wsymb. When n is less than its maximum value of 2wsymb-1, the corresponding code RS(n,k) is referred to as a shortened code. Reed-Solomon codes are characterized by two polynomials: the generator polynomial and the field polynomial. The field polynomial defines the Galois field where the information and check symbols belong. The generator polynomial determines the check symbol generation and it is a prime polynomial for all codewords (i.e. all codewords are exactly divisible by the generator polynomial). Both the field and the generator polynomials are user configurable. Field Polynomial The field polynomial is defined by its decimal value (f). The decimal value of a field polynomial is obtained by setting x = 2 in the polynomial. For example, the polynomial x2 + x + 1 in decimal value is 22 + 2 + 1 = 7. The field polynomial can be specified as any prime polynomial with decimal value up to 2wsymb+1 - 1. Generator Polynomial The generator polynomial determines the value of the check symbols. The generator polynomial can be defined by the parameters starting root (gstart) and root spacing (rootspace). The general form of the generator polynomial is given by: g(x) = (x - rootspace n-k-1 i=0 (gstart + i)) (1) where is called the primitive element of the field polynomial. For a binary Galois field GF(2), is equal to 2. Shortened Codes When the size of the Reed-Solomon codewords, n, is less than the maximum possible size, 2wsymb-1, they are called shortened codes. For example, RS (204,188) when wsymb = 8 is a shortened code. Systematic Decoder The decoder can only decode data encoded by a systematic Reed-Solomon Encoder. In a systematic encoder, the information symbols are unchanged and are followed by check symbols in the output. Decoding Modes The decoder can support Error, Erasure and Puncturing modes. In the error mode no information is available about the symbols in error. In this mode the decoder needs to compute both position and magnitude of the error symbols. In the erasure mode the user can dynamically indicate the erased symbols using the input port ers. Erased symbols are those symbols in error whose positions are known in advance. Error mode can be thought of a special case of Erasure mode, when number of erased symbols is zero. Therefore it is not necessary to identify all correctable errors as erasures through the input port ers in the erasure mode and combinations of errors and erasures IPUG52_01.6, December 2010 11 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Functional Description can be used. If erased symbols are known and the position of the erased symbols can be dynamically indicated using ers, then erasure mode is useful. The symbol correction capability of the decoder increases since the position of the symbol in error is already known and only the magnitude needs to be computed. Generally erasure support substantially increases the decoder latency and resource utilization. Puncturing mode is an optimized version of the erasure mode and can be used when the position of the erased symbols is known in advance. The user can define a maximum of (n - k) puncture patterns and can dynamically select one of these patterns using the input port puncsel. The format for the puncture pattern file is explained in a later section. The decoder will be able to correct the errors and erasures successfully if the following conditions are satisfied. For the Error mode, the number of correctable errors Eerr is given by Eerr = (n - k) /2, when Block size type is constant. Eerr = (Number of check symbols) /2, when Block size type is variable and Variable check symbols is not defined. Eerr = (value on numchks port) /2, when Variable check symbols is defined. For the Erasure and Puncturing modes, the number of correctable errors Eerr and the number of correctable erasures Eers (given through the input port ers) are bound by the following relations (2 * Eerr + Eers (n - k)) and (Eers ((n - k - 2)), when Block size type is constant. (2 * Eerr + Eers (Number of check symbols)) and (Eers (Number of check symbols - 2)), when Block size type is variable. Functional Description A block diagram of the RS Decoder is shown in Figure 2-1. The RS Decoder is comprised of the Syndrome Transform, Key Equation Solver, Error Locator, Error Magnitude Corrector, Data Memory and Output Processing blocks. The data received by the RS Decoder is Reed-Solomon encoded data. This data is a representation of a polynomial in a Galois Field. If there are no errors in the received data, the data polynomial will evaluate to zero at the roots of the generator polynomial. This result is obtained because the roots of the generator polynomial and the received data polynomial are the same when there are no errors. If the received data has been corrupted during the transmission, the polynomial will not evaluate to zero. The RS Decoder can construct the syndrome polynomial by evaluating the received polynomial at all the roots of the generator polynomial. Once the syndrome polynomial has been constructed, it can be used to solve the Error Locator polynomial and Error Evaluator polynomial. Using these two polynomials, the decoder can find the error locations and magnitudes. Finally, the decoder can correct the errors in the received data, provided the errors are in the range of correctable errors (determined by the level of encoding that has been performed). If there are errors in the received codeword, it can be expressed as follows: r(x) = c(x) + e(x) where: c(x) is the Transmitted codeword r(x) is the Received codeword e(x) is the Error polynomial The syndrome polynomial S(x) is obtained by evaluating the received word at each root of the generator polynomial. The Error Locator polynomial (x) is orthogonal to the syndrome polynomial in the Galois field. This can be represented as: IPUG52_01.6, December 2010 12 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Functional Description S(x)(x) = 3/4(x) mod x2t where: 3/4(x) is the Error Evaluator polynomial. 2t is the number of check symbols introduced in the encoder. The following sections describe the function of each block of the RS Decoder. Syndrome Transform The Syndrome Transform (also called Syndrome Generation) block evaluates the received codeword of the generator polynomial. If the received data contains an error, the syndrome polynomial generated will be non-zero. If the received data has no error, the syndrome polynomial is zero, and the data is passed out of the decoder without any error correction. Key Equation Solver This is the heart of the RS Decoder. This block generates the Error Locator polynomial (x) (also known as the "Key Equation" as it is the key to solve the decoding problem). After the Error Locator polynomial has been determined, it is used to compute the Error Evaluator polynomial 3/4(x) Error Locator This block is implemented using the Chien-search method. Essentially, this method evaluates the Error Locator polynomial at all the elements in the Galois Field. The Error Locator polynomial evaluates to zero at its roots. The Chien-search takes up to m cycles, where m is the number of elements in the Galois Field, to determine all the roots. If the roots are determined before m cycles are over, the search is terminated early. Error Magnitude Corrector Once the location of the error has been determined, the Error Magnitude Corrector evaluates the evaluator polynomial at that root. It uses the result to calculate the value of the error at the given location. Once this has been determined, the value is added to the received word to recover the original data. The addition occurs only when the Error Locator polynomial evaluates to zero. Control Unit The control unit handles the interface, pipelining and handshaking communication between the various blocks and the I/O ports. The control circuit moves the data without processing it through the decoder when no error is detected. Similarly, when the number of errors exceeds the maximum range of correction, the control circuit stops all data processing activities. The control circuit interacts with the other blocks to generate the status signals like obstart, obend, outvalid, rfib, errfnd, errcnt, erscnt and fail. Once the block has been processed, the control circuit sends out the rfi signal to the output to start the processing of the next data block. Basis Conversion Modules When core configuration is selected as CCSDS, then two additional Basis Conversion modules are added to the RS Decoder. These modules comply with the CCSDS specification. Dual-basis to normal polynomial-basis conversion module is added after the din input port and normal polynomial-basis to dual-basis conversion module is added before the dout output port. Variable Block Size In the constant Block size type option, the block size value and number of information symbols are provided as constant values through the RS Decoder GUI before core generation. For variable Block size type option, the block size value is provided dynamically through the input port blocksize. The number of the information symbols is calculated from the block size value provided through the input port and the number of check symbols. The number of check symbols can be either constant and defined in the GUI or variable and given through the IPUG52_01.6, December 2010 13 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Functional Description input port numchks, depending on the parameter Variable check symbols. Once block size value, number of check symbols and number of information symbols are known then the core operates in the same way as when block size was constant. Variable Check Symbols This option can be used when there is requirement for variable error correction capability. One example of this type of application is IEEE 802.16-2004 WirelessMAN-SC. In this option the number of check symbols value is provided dynamically through the input port numchks. Dynamically Variable check symbols option is available only for the Error Decoding mode. Puncturing Pattern File Format This file contains the pre-defined puncture patterns that are selected using the puncsel signal. This file is necessary when Decoding mode is selected as Puncturing. This file should have the ".cfg" extension. The RS Decoder IP core GUI requires this file during core configuration. The format and a sample of this file is given below, followed by a brief explanation. Format: <n1> <n2> <n3> ....<nN> First line lists the number of punctured symbols in each pattern. N is the total number of puncture patterns. There should be N lines following this line, one for each pattern <p1> <p2> .... <pn1> <p1> <p2> ... <pn2> ... These are the actual puncture patterns. Each line contains one pattern. p1, p2, etc. in each pattern are the positions of the punctured symbols from the end of the block for that pattern. ... <p1> <p2> ... <pnN> The number of punctured symbols in the first line, <ni>, can be set to zero to indicate there is no puncturing for that pattern. Sample content: 0 4 8 12 0 0123 01234567 0 1 2 3 4 5 6 7 8 9 10 11 In the sample content above, the first line contains the number of punctured symbols for each puncture pattern. 0 indicates that for the first puncture pattern there are 0 symbols punctured. 4 indicates that for the second puncture pattern there are 4 symbols punctured. 8 indicates that for the third puncture pattern there are 8 symbols punctured. 12 indicates that for the fourth puncture pattern there are 12 symbols punctured. The first puncture pattern is defined on line 2 and the second puncture pattern is defined on line 3, and so on. Each puncture pattern lists the position of the punctured symbol starting from the end of the block. This means that the last symbol is numbered as 0 and the next to the last symbol is numbered as 1, and so on. Therefore, for the second puncture pattern defined on line 3, number 0 indicates the last symbol in the block is punctured and number 1 indicates the second from the last symbol is punctured. The values are entered in decimal format. Default Field Polynomials The default field polynomials used in the GUI for different symbol widths are given in Table 2-1. The user, however, can enter any valid polynomial. IPUG52_01.6, December 2010 14 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Functional Description Table 2-1. Default Field Polynomials Symbol Width Default Field Polynomial 3 Decimal Value 3 x +x+1 11 4 x4 + x + 1 19 5 2 5 x + x +1 37 6 x6 + x + 1 67 x7 + x3 + 1 137 x + x4 + x3 + x2 + 1 285 7 8 8 9 4 9 x +x +1 529 10 x10 + x3 + 1 1033 x11 + x2 + 1 2053 x + x6 + x4 + x + 1 4179 11 12 12 Signal Descriptions Table 2-2 shows the definitions of the interface signals available with the RS Decoder IP Core. Table 2-2. Interface Signal Descriptions Port Bits I/O Description clk 1 I System clock. This is the reference clock for input and output data. rstn 1 I System wide asynchronous active-low reset signal. ibstart 1 I Indicates that the data on din is the first information symbol of a new codeword. din 3 - 12 I Input data port. The wsymb parameter defines the port width of this signal. dout 3 - 12 O Output data port. The wsymb parameter defines the port width of this signal. obstart 1 O Output block start. Indicates the first output data of the codeword on the dout port. obend 1 O Output block end. Indicates the last output data of the codeword on the dout port. outvalid 1 O Output data valid. Indicates valid data is present on dout. errfnd 1 O Error found indicator. Asserted at the same time obend is asserted if the block has at least one symbol in error. O Ready for input. Indicates the decoder is ready to receive input data. Typically, this signal is high when the core is ready to read input symbols. This signal is low when the decoder is busy processing a previous block of data and cannot accept new block of data. All Configurations rfi 1 For Variable Check Symbols (When the Parameter Variable check symbols is Yes) rfib numchks 1 2-9 O Ready for input block. Indicates that the decoder is ready to receive the first information symbol in the block. I This port is used to provide the variable number of check symbols value. The width of this port is defined as the number of bits required to represent the Max. number of check symbols parameter value provided by the user. The width of this port is defined as follows: ceil(log2(Max. number of check symbols)). The value at this port is read only when ibstart is high. The operator ceil() stands for the next higher integer. For Variable Block Size Type Only (When the Parameter Variable block size is "Yes") blocksize 3 - 12 IPUG52_01.6, December 2010 I Variable block size value. The value at this port is read only when ibstart is high. The wsymb parameter defines the port width of this signal. 15 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Functional Description Table 2-2. Interface Signal Descriptions (Continued) Port Bits I/O Description For Puncturing Mode (when Decoding mode is "Puncturing" and Number of puncture patterns is More than 1) 1-8 I Puncture pattern select signal. The value on this port selects the puncturing pattern from the number of predefined patterns for the current block of data. The width of this port is defined as ceil(log2(Number of puncture patterns)). The value at this port is read only when ibstart is high. 1 I Erasure. Asserted to indicate the input data symbol at the din port is erased. ce 1 O Clock enable. While this is de-asserted, the decoder will ignore all other synchronous inputs and maintain its current state. sr 1 O Synchronous reset. Asserted for at least one symbol duration in order to reinitialize the decoder state. Input data symbols sampled before sr is asserted are not given at the output. ddel 1 O Original uncorrected data output. A delayed copy of the input data block. Data is presented on ddel concurrently with the decoded block on dout. The wsymb parameter defines the port width of this signal. puncsel For Erasure mode ers Optional I/Os Error Counter. Provides the number of corrected errors in the most recent output block. The bus width errwidth is equal to the number of bits required to represent the maximum possible number of correctable errors, as given in the following equation: When Block size type is Constant, errwidth is defined as errwidth = ciel(log2((n-k+1)/2)) when Error Decoding mode is selected. errwidth = ciel(log2(n-k-0.5)) when Erasure or Puncturing Decoding mode is selected. errcnt 1-8 O When Block size type is Variable and Variable check symbols is No, errwidth is defined as errwidth = ciel(log2((Number of check symbols+1)/2)) when Error Decoding mode is selected. errwidth = ciel(log2(Number of check symbols-0.5)) when Erasure or Puncturing Decoding mode is selected. When Variable check symbols is Yes, errwidth is defined as errwidth = ciel(log2((Max. number of check symbols+1)/2)) The operator ciel() stands for the next higher integer. Erasure Counter. Provides a count of the number of erasures fed into the decoder in the most recent input data block. The bus width erswidth is equal to the number of bits required to represent the maximum possible number of correctable erasures, as given in the following equation: erscnt 1-8 O When Block size type is Constant, erswidth is defined as erswidth = ciel(log2(n-k-1.5)). When Block size type is Variable, erswidth is defined as erswidth = ciel(log2(Number of check symbols -1.5)) The operator ciel() stands for the next higher integer. fail 1 IPUG52_01.6, December 2010 O Decoding failure indicator. Asserted at the same time obend is asserted to indicate that the block has more errors than the decoder can correct. 16 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Functional Description Timing Specifications The decoder receives the data in blocks. The assertion of signal ibstart indicates the first symbol of the new block of data at the input of the decoder. The ibstart signal should be asserted only during the first clock cycle of a data block. The ibstart signal should not be re-asserted until the decoder is ready to receive the next block of data as indicated by rfib going high. The signal rfib can be used to generate the ibstart signal. If a new block of input data has to be applied before the decoder is ready for a new block, the decoder operation should be reset using the synchronous reset signal sr. Figure 2-3 shows the I/O signals' status after asynchronous reset rstn is asserted at the beginning of the block. The output rfi goes high after reset to indicate the core is ready to receive input data. After ibstart signal is asserted, the decoder reads in the data block sequentially and starts the decoding process. When the decoded data is given at the output, obstart is asserted for one clock cycle during the first decoded output symbol. The output obend is asserted for one clock cycle when the last decoded symbol is given at the dout port. Figure 2-3. RS Decoder Normal Operation Timing Diagram clk rstn ce sr rfi rfib ibstart blocksize n o p numchks c1 c2 c3 puncsel p1 p2 p3 ers din CI0 CI1 CI2 CIp-3 CIp-2 CIp-1 dout AO0 AO1 AO2 AOn-3 AOn-2 AOn-1 ddel AI0 AI1 AI2 AIn-3 AIn-2 AIn-1 AI0 AI1 AI2 AIn-3 AIn-2 AIn-1 BI0 BI1 BI2 BIo-3 BIo-2 BIo-1 outvalid obstart obend errfnd errcnt 0 4 erscnt 0 2 fail Figure 2-4 illustrates the output status when sr is asserted. When sr is asserted during the decoding process, it reinitializes the decoder state similar to power on reset state. The output data stops appearing at the output. The decoder operation can be started again by asserting the ibstart signal. IPUG52_01.6, December 2010 17 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Functional Description Figure 2-4. Effect of Synchronous Reset on the Output Data from the Decoder clk rstn ce sr rfi rfib ibstart blocksize n numchks c1 c2 c3 puncsel p1 p2 p3 o p ers din AI0 AI1 AI2 AIn-3 AIn-2 AIn-1 BI0 BI1 BI2 BIo-3 BIo-2 BIo-1 CI0 CI1 CI2 CIp-3 CIp-2 CIp-1 dout ddel outvalid obstart obend errfnd errcnt 0 erscnt 0 fail Figure 2-5 illustrates the effect of clock enable (ce) on the output data from RS Decoder. The decoder ignores all other synchronous inputs and remains in its current state when ce is de-asserted. When ce is asserted, the decoder goes back to the normal decoding process. In the figure, the data DX at din (that occurs during ce going low) is not recognized by the decoder. IPUG52_01.6, December 2010 18 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Functional Description Figure 2-5. Effect of Clock Enable on the Output Data from Decoder clk rstn ce sr rfi rfib ibstart blocksize n o p numchks c1 c2 c3 puncsel p1 p2 p3 ers din CI2 CIp-3 CIp-2 CIp-1 dout AO0 AO1 AO2 AOn-3 AOn-2 AOn-1 ddel AI0 AI1 AI2 AIn-3 AIn-2 AIn-1 AI0 AI1 AI2 AIn-3 AIn-2 AIn-1 BI0 BI1 BI2 BIo-3 BIo-2 BIo-1 CI0 DX CI1 outvalid obstart obend errfnd errcnt 0 4 erscnt 0 2 fail IPUG52_01.6, December 2010 19 Dynamic Block Reed-Solomon Decoder User's Guide Chapter 3: Parameter Settings The IPexpressTM tool is used to create IP and architectural modules in the Diamond and ispLEVER software. Refer to "IP Core Generation" on page 24 for a description on how to generate the IP. The RS Decoder IP core Configuration GUI allows the user to create a custom configuration or to select one of the standard configurations: OC-192, CCSDS, DVB, ATSC, IEEE 802.16-2004 WirelessMAN-SCa/OFDM and IEEE 802.16-2004 WirelessMAN-SC. Table 3-1 provides the list of user configurable parameters for the RS Decoder IP core. Table 3-1. User Configurable Parameters Parameter Range/Options Default Custom, OC-192, CCSDS, DVB, ATSC, IEEE 802.16-2004 SCa, IEEE 802.16-2004 SC OC-192 Yes/No Yes Core Configuration Core configuration Connect reset port to GSR RS Parameters wsymb 3 - 12 bits 8 bits fpoly 5 - 8191 285 gstart 0 - 65535 0 rootspace 1 - 65535 1 Yes/No No Check Symbols Variable check symbols wsymb Number of check symbols 4 - ((2 )-2). Maximum value is limited to 256. 16 Max. number of check symbols 4 - ((2wsymb)-2). Maximum value is limited to 128. 32 Variable} if Variable check symbols is checked. {Constant, Variable} if Variable check symbols is not checked. {Constant} if wsymb is 3 and Decoding mode is Erasure. Constant 5 - ((2wsymb)-1) Default value is ((2wsymb)-1) 255 1 - (n-4) 239 Number of puncture patterns 1 - (n-k) when Block size is Constant. 1 - (Number of check symbols) when Block size is Variable. 1 Puncture pattern file Edit field to enter the file name directly or indirectly by using the browse button. Block Size Type Block size type Block size(n) Information symbols(k) Puncturing Decoding Mode Decoding mode {Error, Erasure, Puncturing} Error {Automatic, Block, Distributed} Automatic Memory Type Memory type Optional Ports ce Yes/No No sr Yes/No No errcnt Yes/No Yes ddel Yes/No Yes fail Yes/No No erscnt Yes/No IPUG52_01.6, December 2010 20 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Parameter Settings RS Decoder Configuration GUI Figure 3-1 shows the contents of the RS Decoder IP core Configuration GUI. Figure 3-1. RS Decoder IP core Configuration GUI Core Configuration Selects between custom and pre-defined standard configurations. Table A-1 on page 33 defines the fixed parameter values for different standard configurations. RS Parameters Wsymb This parameter sets symbol width. Fpoly This parameter sets the decimal value of the field polynomial. Table 2-1 on page 15 gives the default field polynomial values for different symbol widths. Gstart This parameter sets the offset value of the generator polynomial. The starting value for the first root of the generator polynomial is calculated as rootspace * gstart. IPUG52_01.6, December 2010 21 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Parameter Settings Rootspace This parameter sets the root spacing of the generator polynomial. The value of rootspace must satisfy the following equation: GCD(rootspace, 2wsymb-1) = 1. GCD is Greatest Common Divisor. Check Symbols Variable Check Symbols This option allows the number of check symbols to be varied through the port in addition to varying the block size dynamically. In this case, the number of check symbols is defined through the input port numchks. This option is available only when Block size type is Variable and Decoding mode is Error. Number of Check Symbols Constant value for the Number of check symbols in the codeword. This parameter is available when Block size type is selected as Variable and Variable check symbols is not checked. Max. Number of Check Symbols Maximum value for number of check symbols provided through the input port numchks. This parameter selection is available only when Variable check symbols is checked. Block Size Type This parameter specifies whether block size is provided as a constant value or varied through the input port. If Block size type is selected as Variable, the block size is read from the input port blocksize. Options depend on Variable check symbols. Block Size(n) This parameter specifies the total number of symbols in the codeword. Defined only if Block size type is Constant. Information Symbols(k) This parameter specifies the number of information symbols in the codeword. Defined only if Block size type is Constant. The value of k also depends on n as the maximum value of (n-k) is limited to 256 Puncturing Number of Puncture Patterns This is the number of pre-defined puncture patterns that can be dynamically selected using puncsel. This parameter is enabled when Decoding mode is selected as Puncturing. Puncture Pattern File This is the file containing the pre-defined puncture patterns. The format of the puncture pattern file is described in the Puncture Pattern File Format section of this document. The browse button to load the puncture pattern file is enabled when Decoding mode is selected as Puncturing. The file should have a .cfg extension. Decoding Mode Selects between different decoding modes. The selection of this parameter depends on the application requirements. Memory Type Specifies the type of memory used for storing input data. If Memory type is selected as Block, then EBR memory is used. If Memory type is selected as Distributed then distributed memory is used. If Memory type is selected as Automatic then memory will be selected in a most optimized way depending on the other parameters selected. IPUG52_01.6, December 2010 22 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Parameter Settings Optional Ports ce Determines whether the input port ce (clock enable) is present. sr Determines whether the input port sr (synchronous reset) is present. errcnt Determines whether the output port errcnt (error count) is present. ddel Determines whether the output port ddel (delayed data) is present. fail Determines whether the output port fail (decoding failure) is present. erscnt Determines whether the output port erscnt (erasure count) is present. IPUG52_01.6, December 2010 23 Dynamic Block Reed-Solomon Decoder User's Guide Chapter 4: IP Core Generation This chapter provides information on licensing the RS Decoder IP core, generating the core using the Diamond or ispLEVER software IPexpress tool, running functional simulation, and including the core in a top-level design. The Lattice RS Decoder IP core can be used in LatticeECP3, LatticeECP2/M, LatticeECP, LatticeSC/M, LatticeXP, and LatticeXP2 device families. Licensing the IP Core An IP license is required to enable full, unrestricted use of the RS Decoder IP core in a complete, top-level design. An IP license that specifies the IP core and device family is required to enable full use of the core in Lattice devices. Instructions on how to obtain licenses for Lattice IP cores are given at: http://www.latticesemi.com/products/intellectualproperty/aboutip/isplevercoreonlinepurchas.cfm Users may download and generate the IP core and fully evaluate the core through functional simulation and implementation (synthesis, map, place and route) without an IP license. The RS Decoder IP core core also supports Lattice's IP hardware evaluation capability, which makes it possible to create versions of the IP core that operate in hardware for a limited time (approximately four hours) without requiring an IP license (see "Instantiating the Core" on page 28 for further details). However, a license is required to enable timing simulation, to open the design in the Diamond or ispLEVER EPIC tool, and to generate bitstreams that do not include the hardware evaluation timeout limitation. Getting Started The RS Decoder IP core is available for download from the Lattice IP Server using the IPexpress tool. The IP files are automatically installed using ispUPDATE technology in any customer-specified directory. After the IP core has been installed, the IP core will be available in the IPexpress GUI dialog box shown in Figure 4-1. The IPexpress tool GUI dialog box for the RS Decoder IP core is shown in Figure 4-1. To generate a specific IP core configuration the user specifies: * Project Path - Path to the directory where the generated IP files will be located. * File Name - "username" designation given to the generated IP core and corresponding folders and files. * (Diamond) Module Output - Verilog or VHDL. * (ispLEVER) Design Entry Type - Verilog HDL or VHDL. * Device Family - Device family to which IP is to be targeted (e.g. LatticeSCM, Lattice ECP2M, LatticeECP3, etc.). Only families that support the particular IP core are listed. * Part Name - Specific targeted part within the selected device family. IPUG52_01.6, December 2010 24 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor IP Core Generation Figure 4-1. IPexpress Tool Dialog Box (Diamond Version) Note that if the IPexpress tool is called from within an existing project, Project Path, Module Output (Design Entry in ispLEVER), Device Family and Part Name default to the specified project parameters. Refer to the IPexpress tool online help for further information. To create a custom configuration, the user clicks the Customize button in the IPexpress tool dialog box to display the RS Decoder IP core Configuration GUI, as shown in Figure 4-2. From this dialog box, the user can select the IP parameter options specific to their application. Refer to "Parameter Settings" on page 16for more information on the parameter settings. IPUG52_01.6, December 2010 25 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor IP Core Generation Figure 4-2. Configuration GUI (Diamond Version) IPexpress-Created Files and Top Level Directory Structure When the user clicks the Generate button in the IP Configuration dialog box, the IP core and supporting files are generated in the specified "Project Path" directory. The directory structure of the generated files is shown in Figure 4-3. IPUG52_01.6, December 2010 26 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor IP Core Generation Figure 4-3. Lattice RS Decoder IP core Directory Structure Table 4-1 provides a list of key files and directories created by the IPexpress tool and how they are used. The IPexpress tool creates several files that are used throughout the design cycle. The names of most of the created files are customized to the user's module name specified in the IPexpress tool. Table 4-1. File List File Description <username>_inst.v This file provides an instance template for the IP. <username>.v This file provides the RS Decoder core for simulation. <username>_beh.v This file provides a behavioral simulation model for the RS Decoder core. <username>_bb.v This file provides the synthesis black box for the user's synthesis. <username>.ngo The ngo files provide the synthesized IP core. <username>.lpc This file contains the IPexpress tool options used to recreate or modify the core in the IPexpress tool. <username>.ipx The IPX file holds references to all of the elements of an IP or Module after it is generated from the IPexpress tool (Diamond version only). The file is used to bring in the appropriate files during the design implementation and analysis. It is also used to re-load parameter settings into the IP/Module generation GUI when an IP/Module is being re-generated. <username>_top.[v,vhd] This file provides a module which instantiates the RS Decoder core. This file can be easily modified for the user's instance of the RS Decoder core. This file is located in the rsdec_eval/<username>_/src/rtl/top/ directory. <username>_generate.tcl Created when GUI "Generate" button is pushed, invokes generation, may be run from command line. <username>_generate.log IPexpress scripts log file. <username>_gen.log IPexpress IP generation log file IPUG52_01.6, December 2010 27 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor IP Core Generation Instantiating the Core The generated RS Decoder IP core package includes black-box (<username>_bb.v) and instance (<username>_inst.v) templates that can be used to instantiate the core in a top-level design. An example RTL top-level reference source file that can be used as an instantiation template for the IP core is provided in \<project_dir>\rsdec_eval\<username>\src\rtl\top. Users may also use this top-level reference as the starting template for the top-level for their complete design. Running Functional Simulation Simulation support for the RS Decoder IP core is provided for Aldec Active-HDL (Verilog and VHDL) simulator, Mentor Graphics ModelSim simulator. The functional simulation includes a configuration-specific behavioral model of the RS Decoder IP core. The test bench sources stimulus to the core, and monitors output from the core. The generated IP core package includes the configuration-specific behavior model (<username>_beh.v) for functional simulation in the "Project Path" root directory. The simulation scripts supporting ModelSim evaluation simulation is provided in \<project_dir>\rsdec_eval\<username>\sim\modelsim\scripts. The simulation script supporting Aldec evaluation simulation is provided in \<project_dir>\rsdec_eval\<username>\sim\aldec\scripts. Both Modelsim and Aldec simulation is supported via test bench files provided in \<project_dir>\rsdec_eval\testbench. Models required for simulation are provided in the corresponding \models folder. Users may run the Aldec evaluation simulation by doing the following: 1. Open Active-HDL. 2. Under the Tools tab, select Execute Macro. 3. 3. Browse to folder \<project_dir>\rsdec_eval\<username>\sim\aldec\scripts and execute one of the "do" scripts shown. Users may run the ModelSim evaluation simulation by doing the following: 1. Open ModelSim. 2. Under the File tab, select Change Directory and choose the folder <project_dir>\rsdec_eval\<username>\sim\modelsim\scripts. 3. Under the Tools tab, select Execute Macro and execute the ModelSim "do" script shown. Note: When the simulation completes, a pop-up window will appear asking "Are you sure you want to finish?" Answer No to analyze the results (answering Yes closes ModelSim). Synthesizing and Implementing the Core in a Top-Level Design Synthesis support for the RS Decoder IP core is provided for Mentor Graphics Precision or Synopsys Synplify. The RS Decoder IP core itself is synthesized and is provided in NGO format when the core is generated in IPexpress. Users may synthesize the core in their own top-level design by instantiating the core in their top-level as described previously and then synthesizing the entire design with either Synplify or Precision RTL Synthesis. The following text describes the evaluation implementation flow for Windows platforms. The flow for Linux and UNIX platforms is described in the Readme file included with the IP core. The top-level files <username>_top.v are provided in \<project_dir>\rsdec_eval\<username>\src\rtl\top. Push-button implementation of the reference design is supported via Diamond or ispLEVER project files, <username>.syn, located in the following directory: \<project_dir>\rsdec_eval\<username>\impl\(synplify or precision). To use these project files using Synplify: To use this project file in Diamond: 1. Choose File > Open > Project. IPUG52_01.6, December 2010 28 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor IP Core Generation 2. Browse to \<project_dir>\rsdec_eval\<username>\impl\synplify (or precision) in the Open Project dialog box. 3. Select and open <username>.ldf. At this point, all of the files needed to support top-level synthesis and implementation will be imported to the project. 4. Select the Process tab in the left-hand GUI window. 5. Implement the complete design via the standard Diamond GUI flow. To use this project file in ispLEVER: 1. Choose File > Open Project. 2. Browse to \<project_dir>\rsdec_eval\<username>\impl\synplify (or precision) in the Open Project dialog box. 3. Select and open <username>.syn. At this point, all of the files needed to support top-level synthesis and implementation will be imported to the project. 4. Select the device top-level entry in the left-hand GUI window. 5. Implement the complete design via the standard ispLEVER GUI flow. Hardware Evaluation The RS Decoder IP core supports Lattice's IP hardware evaluation capability, which makes it possible to create versions of the IP core that operate in hardware for a limited period of time (approximately four hours) without requiring the purchase of an IP license. It may also be used to evaluate the core in hardware in user-defined designs. Enabling Hardware Evaluation in Diamond Choose Project > Active Strategy > Translate Design Settings. The hardware evaluation capability may be enabled/disabled in the Strategy dialog box. It is enabled by default. Enabling Hardware Evaluation in ispLEVER In the Processes for Current Source pane, right-click the Build Database process and choose Properties from the dropdown menu. The hardware evaluation capability may be enabled/disabled in the Properties dialog box. It is enabled by default. Updating/Regenerating the IP Core By regenerating an IP core with the IPexpress tool, you can modify any of its settings including device type, design entry method, and any of the options specific to the IP core. Regenerating can be done to modify an existing IP core or to create a new but similar one. Regenerating an IP Core in Diamond To regenerate an IP core in Diamond: 1. In IPexpress, click the Regenerate button. 2. In the Regenerate view of IPexpress, choose the IPX source file of the module or IP you wish to regenerate. 3. IPexpress shows the current settings for the module or IP in the Source box. Make your new settings in the Target box. IPUG52_01.6, December 2010 29 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor IP Core Generation 4. If you want to generate a new set of files in a new location, set the new location in the IPX Target File box. The base of the file name will be the base of all the new file names. The IPX Target File must end with an .ipx extension. 5. Click Regenerate. The module's dialog box opens showing the current option settings. 6. In the dialog box, choose the desired options. To get information about the options, click Help. Also, check the About tab in IPexpress for links to technical notes and user guides. IP may come with additional information. As the options change, the schematic diagram of the module changes to show the I/O and the device resources the module will need. 7. To import the module into your project, if it's not already there, select Import IPX to Diamond Project (not available in stand-alone mode). 8. Click Generate. 9. Check the Generate Log tab to check for warnings and error messages. 10.Click Close. The IPexpress package file (.ipx) supported by Diamond holds references to all of the elements of the generated IP core required to support simulation, synthesis and implementation. The IP core may be included in a user's design by importing the .ipx file to the associated Diamond project. To change the option settings of a module or IP that is already in a design project, double-click the module's .ipx file in the File List view. This opens IPexpress and the module's dialog box showing the current option settings. Then go to step 6 above. Regenerating an IP Core in ispLEVER To regenerate an IP core in ispLEVER: 1. In the IPexpress tool, choose Tools > Regenerate IP/Module. 2. In the Select a Parameter File dialog box, choose the Lattice Parameter Configuration (.lpc) file of the IP core you wish to regenerate, and click Open. 3. The Select Target Core Version, Design Entry, and Device dialog box shows the current settings for the IP core in the Source Value box. Make your new settings in the Target Value box. 4. If you want to generate a new set of files in a new location, set the location in the LPC Target File box. The base of the .lpc file name will be the base of all the new file names. The LPC Target File must end with an .lpc extension. 5. Click Next. The IP core's dialog box opens showing the current option settings. 6. In the dialog box, choose desired options. To get information about the options, click Help. Also, check the About tab in the IPexpress tool for links to technical notes and user guides. The IP core might come with additional information. As the options change, the schematic diagram of the IP core changes to show the I/O and the device resources the IP core will need. 7. Click Generate. 8. Click the Generate Log tab to check for warnings and error messages. IPUG52_01.6, December 2010 30 Dynamic Block Reed-Solomon Decoder User's Guide Chapter 5: Support Resources This chapter contains information about Lattice Technical Support, additional references, and document revision history. Lattice Technical Support There are a number of ways to receive technical support. Online Forums The first place to look is Lattice Forums (http://www.latticesemi.com/support/forums.cfm). Lattice Forums contain a wealth of knowledge and are actively monitored by Lattice Applications Engineers. Telephone Support Hotline Receive direct technical support for all Lattice products by calling Lattice Applications from 5:30 a.m. to 6 p.m. Pacific Time. * For USA & Canada: 1-800-LATTICE (528-8423) * For other locations: +1 503 268 8001 In Asia, call Lattice Applications from 8:30 a.m. to 5:30 p.m. Beijing Time (CST), +0800 UTC. Chinese and English language only. * For Asia: +86 21 52989090 E-mail Support * techsupport@latticesemi.com * techsupport-asia@latticesemi.com Local Support Contact your nearest Lattice Sales Office. Internet www.latticesemi.com References * I. S. Reed, M. T. Shih, and T. K. Truong, "VLSI design of inverse-free Berlekamp-Massey algorithm," Proc. IEEE, Part E, vol. 138, pp. 295-298, September 1991. * S. Kwon and H. Shin, "An area-efficient VLSI architecture of a Reed-Solomon decoder/encoder for digital VCRs," IEEE Trans. Consumer Electronics, pp. 1019-1027, Nov. 1997. LatticeEC/ECP * HB1000, LatticeECP/EC Family Handbook LatticeECP2M * HB1003, LatticeECP2M Family Handbook LatticeECP3 * HB1009, LatticeECP3 Family Handbook IPUG52_01.6, December 2010 31 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Support Resources LatticeSC/M * DS1004, LatticeSC/M Family Data Sheet LatticeXP * HB1001, LatticeXP Family Handbook LatticeXP2 * DS1009, Lattice XP2 Datasheet Related Information For more information regarding core usage and design verification, refer to the Reed-Solomon Decoder IP Core User's Guide. Revision History Date Document Version IP Version Change Summary March 2006 01.0 2.0 Initial release. August 2006 01.1 3.0 Core version 3.0: Full support of IPexpress flow, including LatticeECP/EC, LatticeECP2, LatticeSC, and LatticeXP. January 2007 01.2 3.1 Updated LatticeECP/EC, LatticeECP2, LatticeXP and LatticeSC appendices. Added support for the LatticeECP2M FPGA family. May 2007 01.3 3.2 Added support for LatticeXP2 FPGA family. May 2009 01.4 3.3 Added support for LatticeECP3 FPGA family. Added VHDL flow. Added Aldec Active-HDL simulation and Linux/Solaris platform support. July 2010 01.5 3.3 Divided document into chapters. Added table of contents. Added Quick Facts tables in Chapter 1, "Introduction." Added new content in Chapter 4, "IP Core Generation." December 2010 01.6 IPUG52_01.6, December 2010 3.4 Added support for Diamond software throughout. 32 Dynamic Block Reed-Solomon Decoder User's Guide Appendix A: Resource Utilization This appendix gives resource utilization information for Lattice FPGAs using the RS Decoder IP core. IPexpress is the Lattice IP configuration utility, and is included as a standard feature of the Diamond and ispLEVER design tools. Details regarding the usage of IPexpress can be found in the IPexpress and Diamond or ispLEVER help system. For more information on the Diamond or ispLEVER design tools, visit the Lattice web site at: www.latticesemi.com/software. Table A-1 gives the parameter settings for the standard configurations shown in Table A-2 through Table A-8. Table A-1. Parameter Settings for Standard Configurations Core Configuration OC-192 (config1) Parameter Name CCSDS (config2) DVB (config3) ATSC (config4) IEEE 802.16-2004 WirelessMA-SCa or IEEE 802.16-2004 WirelessMA-OFDM WirelessMAN-SC (config5) (config6) RS Parameters wsymb 8 8 8 8 8 8 285 391 285 285 285 285 gstart 0 112 0 0 0 0 rootspace 1 11 1 1 1 1 Variable check symbols No No No No No Yes Number of check symbols NA NA NA NA 16 NA Max. number of check symbols NA NA NA NA NA 32 Constant Constant Constant Constant Variable Variable fpoly Check Symbols Block Size Type Block size type Block size(n) 255 255 204 207 NA NA InfoSymbols(k) 239 223 188 187 NA NA NA NA NA NA 4 NA Error Error Error Error Puncturing Error Automatic Automatic Automatic Automatic Automatic Automatic No No No No No No Puncturing Number of puncture patterns Decoding Mode Decoding mode Memory Type Memory type Optional Input/Output Ports ce sr No No No No No No errcnt Yes Yes Yes Yes Yes Yes ddel Yes Yes Yes Yes Yes Yes fail No No No No No No erscnt NA NA NA NA Yes NA IPUG52_01.6, December 2010 33 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Resource Utilization LatticeECP and LatticeEC FPGAs Table A-2. Performance and Resource Utilization1 Slices LUTs Registers sysMEMTM EBRs I/Os fMAX (MHz) OC-192 588 1171 795 2 37 123 CCSDS 980 1947 1349 2 38 114 DVB 604 1196 802 2 37 124 IPexpress User-Configurable Mode ATSC 766 1520 969 2 37 113 IEEE 802.16-2004 WirelessMAN SCa 927 1835 1279 2 51 116 IEEE 802.16-2004 WirelessMAN SC 1044 2066 1486 2 52 104 1. Performance and utilization data are generated using an LFEC/P20E-5F672C device with Lattice Diamond 1.0 and Synplify Pro for Lattice D-2009.12L-1 software. Performance may vary when using a different software version or targeting a different device density or speed grade within the LatticeECP/EC family. Ordering Part Number The Ordering Part Number (OPN) for the RS Decoder core targeting LatticeECP/EC devices is RSDEC-DBLK-E2U3. LatticeECP2 and LatticeECP2S FPGAs Table A-3. Performance and Resource Utilization1 IPexpress User-Configurable Mode Registers sysMEM EBRs I/Os fMAX (MHz) 1117 791 2 37 175 1917 1322 2 38 157 Slices LUTs OC-192 562 CCSDS 963 DVB 591 1173 792 2 37 150 ATSC 756 1500 960 2 37 166 IEEE 802.16-2004 WirelessMAN SCa 917 1818 1252 2 51 152 IEEE 802.16-2004 WirelessMAN SC 1037 2056 1493 2 52 137 1. Performance and utilization data are generated using an LFE2-50E/S-7F672C device with with Lattice Diamond 1.0 and Synplify Pro for Lattice D-2009.12L-1 software. Performance may vary when using a different software version or targeting a different device density or speed grade within the LatticeECP2/S family. Ordering Part Number The Ordering Part Number (OPN) for the RS Decoder core targeting LatticeECP2/S devices is RSDEC-DBLK-P2-U3. IPUG52_01.6, December 2010 34 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Resource Utilization LatticeECP2M and LatticeECP2MS FPGAs Table A-4. Performance and Resource Utilization1 Slices LUTs Registers sysMEM EBRs I/Os fMAX (MHz) OC-192 562 1117 791 2 37 169 CCSDS 963 1917 1322 2 38 163 DVB 591 1173 792 2 37 178 ATSC 756 1500 960 2 37 160 IEEE 802.16-2004 WirelessMAN SCa 917 1818 1252 3 51 151 IEEE 802.16-2004 WirelessMAN SC 1037 2056 1493 3 52 145 IPexpress User-Configurable Mode 1. Performance and utilization data are generated using an LFE2M35E/SE-7F484C device with with Lattice Diamond 1.0 and Synplify Pro for Lattice D-2009.12L-1 software. Performance may vary when using a different software version or targeting a different device density or speed grade within the LatticeECP2M/S family. Ordering Part Number The Ordering Part Number (OPN) for the RS Decoder core targeting LatticeECP2M/S devices is RSDEC-DBLK-PM-U3. LatticeECP3 FPGAs Table A-5. Performance and Resource Utilization1 Slices LUTs Registers sysMEM EBRs I/Os fMAX (MHz) OC-192 564 1062 791 2 37 148 CCSDS 990 1884 1322 2 38 149 DVB 591 1123 792 2 37 156 IPexpress User-Configurable Mode ATSC 776 1476 960 2 37 144 IEEE 802.16-2004 WirelessMAN SCa 912 1746 1252 2 51 145 IEEE 802.16-2004 WirelessMAN SC 1067 2031 1493 2 52 142 1. Performance and utilization data are generated using an LFE3-95E-8FN672CES device with with Lattice Diamond 1.0 and Synplify Pro for Lattice D-2009.12L-1 software. Performance may vary when using a different software version or targeting a different device density or speed grade within the LatticeECP3 family. Ordering Part Number The Ordering Part Number (OPN) for the RS Decoder core targeting LatticeECP3 devices is RSDEC-DBLK-P3-U3. IPUG52_01.6, December 2010 35 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Resource Utilization LatticeXP FPGAs Table A-6. Performance and Resource Utilization1 Slices LUTs Registers sysMEM EBRs I/Os fMAX (MHz) OC-192 588 1171 795 2 37 110 CCSDS 980 1947 1349 2 38 108 DVB 604 1196 802 2 37 111 ATSC 766 1520 969 2 37 103 IEEE 802.16-2004 WirelessMAN SCa 928 1837 1279 2 51 109 IEEE 802.16-2004 WirelessMAN SC 1044 2066 1486 2 52 85 IPexpress User-Configurable Mode 1. Performance and utilization data are generated using an LFXP20E-5F484C device with with Lattice Diamond 1.0 and Synplify Pro for Lattice D-2009.12L-1 software. Performance may vary when using a different software version or targeting a different device density or speed grade within the LatticeXP family. Ordering Part Number The Ordering Part Number (OPN) for the RS Decoder core targeting LatticeXP devices is RSDEC-DBLK-XP-U3. LatticeXP2 FPGAs Table A-7. Performance and Resource Utilization1 Slices LUTs Registers sysMEM EBRs I/Os fMAX (MHz) OC-192 562 1117 791 2 37 140 CCSDS 963 1917 1322 2 38 128 DVB 591 1173 792 2 37 157 IPexpress User-Configurable Mode ATSC 756 1500 960 2 37 128 IEEE 802.16-2004 WirelessMAN SCa 917 1818 1252 2 51 126 IEEE 802.16-2004 WirelessMAN SC 1037 2056 1493 2 52 127 1. Performance and utilization data are generated using an LFXP2-30E-7F484C device with with Lattice Diamond 1.0 and Synplify Pro for Lattice D-2009.12L-1 software. Performance may vary when using a different software version or targeting a different device density or speed grade within the LatticeXP2 family. Ordering Part Number The Ordering Part Number (OPN) for the RS Decoder core targeting LatticeXP2 devices is RSDEC-DBLK-X2-U3. IPUG52_01.6, December 2010 36 Dynamic Block Reed-Solomon Decoder User's Guide Lattice Semiconductor Resource Utilization LatticeSC and LatticeSCM FPGAs Table A-8. Performance and Resource Utilization1 Slices LUTs Registers sysMEM EBRs I/Os fMAX (MHz) OC-192 591 1113 803 2 37 267 CCSDS 1033 1958 1348 2 38 245 DVB 642 1219 804 2 37 287 ATSC 804 1537 970 2 37 253 IEEE 802.16-2004 WirelessMAN SCa 965 1833 1276 2 51 240 IEEE 802.16-2004 WirelessMAN SC 1107 2101 1501 2 52 238 IPexpress User-Configurable Mode 1. Performance and utilization data are generated using an LFSC/M3GA25E-7F900C device with with Lattice Diamond 1.0 and Synplify Pro for Lattice D-2009.12L-1 software. Performance may vary when using a different software version or targeting a different device density or speed grade within the LatticeSC/M family. Ordering Part Number The Ordering Part Number (OPN) for the RS Decoder core targeting LatticeSC/M devices is RSDEC-DBLK-SC-U3. IPUG52_01.6, December 2010 37 Dynamic Block Reed-Solomon Decoder User's Guide Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Lattice: RSDEC-DBLK-E2-U3 RSDEC-DBLK-P2-U3 RSDEC-DBLK-SC-U3 RSDEC-DBLK-XM-U3