DS275 Line-Powered RS-232 Transceiver Chip www.dalsemi.com FEATURES PIN ASSIGNMENT Low-power serial transmitter/receiver for battery-backed systems Transmitter steals power from receive signal line to save power Ultra-low static current, even when connected to RS-232-E port Variable transmitter level from +5 to +12 volts Compatible with RS-232-E signals Available in 8-pin, 150 mil wide SOIC package (DS275S) Low-power CMOS 8-pin DIP 8-pin SOIC 14-pin TSSOP 1 8 VCC VDRV 2 7 RXIN TXIN 3 6 NC GND 4 5 TXOUT DS275 8-Pin DIP (300-mil) DS275 8-Pin SOIC (150-mil) RXOUT NC VDRV NC TXIN NC GND ORDERING INFORMATION DS275 DS275S DS275E RXOUT 1 2 3 4 5 6 7 14 13 12 11 10 9 8 VCC NC NC RXIN NC NC TXOUT DS275E 14-Pin TSSOP PIN DESCRIPTION RXOUT VDRV TXIN GND TXOUT NC RXIN VCC - RS-232 Receiver Output - Transmit driver +V - RS-232 Driver Input - System Ground (0V) - RS-232 Driver Output - No Connection - RS-232 Receive Input -System Logic Supply (+5V) DESCRIPTION The DS275 Line-Powered RS-232 Transceiver Chip is a CMOS device that provides a low-cost, very low-power interface to RS-232 serial ports. The receiver input translates RS-232 signal levels to common CMOS/TTL levels. The transmitter employs a unique circuit which steals current from the receive RS232 signal when that signal is in a negative state (marking). Since most serial communication ports remain in a negative state statically, using the receive signal for negative power greatly reduces the DS275's static power consumption. This feature is especially important for battery-powered systems such as laptop computers, remote sensors, and portable medical instruments. During an actual communication session, the DS275's transmitter will use system power (5-12 volts) for positive transitions while still employing the receive signal for negative transitions. 1 of 8 112299 DS275 DS275 BLOCK DIAGRAM Figure 1 OPERATION Designed for the unique requirements of battery-backed systems, the DS275 provides a low-power halfduplex interface to an RS-232 serial port. Typically, a designer must use an RS-232 device which uses system power during both negative and positive transitions of the transmit signal to the RS-232 port. If the connector to the RS-232 port is left connected for an appreciable time after the communication session has ended, power will statically flow into that port, draining the battery capacity. The DS275 eliminates this static current drain by stealing current from the receive line (RXIN) of the RS-232 port when that line is at a negative level (marking). Since most asynchronous communication over an RS-232 connection typically remains in a marking state when data is not being sent, the DS275 will not consume system power in this condition. System power would only be used when positive-going transitions are needed on the transmit RS-232 output (TXOUT) when data is sent. However, since synchronous communication sessions typically exhibit a very low duty-cycle, overall system power consumption remains low. RECEIVER SECTION The RXIN pin is the receive input for an RS-232 signal whose levels can range from 3 to 15 volts. A negative data signal is called a mark while a positive data signal is called a space. These signals are inverted and then level-shifted to normal +5-volt CMOS/TTL logic levels. The logic output associated with RXIN is RXOUT which swings from +VCC to ground. Therefore, a mark on RXIN produces a logic 1 at RXOUT; a space produces a logic 0. The input threshold of RXIN is typically around 1.8 volts with 500 millivolts of hysteresis to improve noise rejection. Therefore, an input positive-going signal must exceed 1.8 volts to cause RXOUT to switch states. A negative-going signal must now be lower than 1.3 volts (typically) to cause RXOUT to switch again. An open on RXIN is interpreted as a mark, producing a logic 1 at RXOUT. TRANSMITTER SECTION TXIN is the CMOS/TTL-compatible input for digital data from the user system. A logic 1 at TXIN produces a mark (negative data signal) at TXOUT while a logic 0 produces a space (positive data signal). As mentioned earlier, the transmitter section employs a unique driver design that uses the RXIN line for swinging to negative levels. The RXIN line must be in a marking or idle state to take advantage of this design; if RXIN is in a spacing state, TXOUT will only swing to ground. When TXOUT needs to transition to a positive level, it uses the VDRV power pin for this level. VDRV can be a voltage supply between 5 to 12 2 of 8 DS275 volts, and in many situations it can be tied directly to the +5 volt VCC supply. It is important to note that VDRV must be greater than or equal to VCC at all times. The voltage range on VDRV permits the use of a 9-volt battery in order to provide a higher voltage level when TXOUT is in a space state. When VCC is shut off to the DS275 and VDRV is still powered (as might happen in a battery-backed condition), only a small leakage current (about 50-100 nA) will be drawn. If TXOUT is loaded during such a condition, VDRV will draw current only if RXIN is not in a negative state. During normal operation (VCC=5 volts), VDRV will draw less than 2 uA when TXOUT is marking. Of course, when TXOUT is spacing, VDRV will draw substantially more current =about 3 mA, depending upon its voltage and the impedance that TXOUT sees. The TXOUT output is slew rate-limited to less than 30 volts/us in accordance with RS-232 specifications. In the event TXOUT should be inadvertently shorted to ground, internal current-limiting circuitry prevents damage, even if continuously shorted. RS-232 COMPATIBILITY The intent of the DS275 is not so much to meet all the requirements of the RS-232 specification as to offer a low-power solution that will work with most RS-232 ports with a connector length of less than 10 feet. As a prime example, the DS275 will not meet the RS-232 requirement that the signal levels be at least 5 volts minimum when terminated by a 3 k =load and VDRV = +5 volts. Typically a voltage of 4 volts will be present at TXOUT when spacing. However, since most RS-232 receivers will correctly interpret any voltage over 2 volts as a space, there will be no problem transmitting data. APPLICATIONS INFORMATION The DS275 is designed as a low-cost, RS-232-E interface expressly tailored for the unique requirements of battery-operated handheld products. As shown in the electrical specifications, the DS275 draws exceptionally low operating and static current. During normal operation when data from the handheld system is sent from the TXOUT output, the DS275 only draws significant VDRV current when TXOUT transitions positively (spacing). This current flows primarily into the RS-232 receiver's 3-7 k =load at the other end of the attaching cable. When TXOUT is marking (a negative data signal), the VDRV current falls dramatically since the negative voltage is provided by the transmit signal from the other end of the cable. This represents a large reduction in overall operating current, since typical RS-232 interface chips use charge-pump circuits to establish both positive and negative levels at the transmit driver output. To obtain the lowest power consumption from the DS275, observe the following guidelines. First, to minimize VDRV current when connected to an RS-232 port, always maintain TXIN at a logic 1 when data is not being transmitted (idle state). This will force TXOUT into the marking state, minimizing VDRV current. Second, VDRV current will drop to less than 100 nA when VCC is grounded. Therefore, if VDRV is tied directly to the system battery, the logic +5 volts can be turned off to achieve the lowest possible power state. FULL-DUPLEX OPERATION The DS275 is intended primarily for half-duplex operation; that is, RXIN should remain idle in the marking state when transmitting data out TXOUT and visa versa. However, the part can be operated fullduplex with most RS-232-E serial ports since signals swinging between 0 and +5V will usually be correctly interpreted by an RS-232-E receiver device. The 5-volt swing occurs when TXOUT attempts to swing negative while RXIN is at a positive voltage, which turns on an internal weak pulldown to ground for the TXOUT driver's negative reference. So, transmit mark signals at TXOUT may have voltage jumps from some negative value (corresponding to RXIN marking) to approximately ground. One possible 3 of 8 DS275 problem that may occur in this case is if the receiver at the other end requires a negative voltage for recognizing a mark. In this situation, the full-duplex circuit shown in Figure 3 can be used as analternative. The 22 F capacitor forms a negative-charge reservoir; consequently, when the TXD line is spacing (positive), TXOUT still has a negative source available for a time period determined by the capacitor and the load resistance at the other end (3-7 k ). This circuit was tested from 150-19,200 bps with error-free operation using a SN75154 Quad Line Receiver as the receiver for the TXOUT signal. Note that the SN75154 can have a marking input threshold below ground; hence there is the need for TXOUT to swing both positive and negative in full-duplex operation with this device. HANDHELD RS-232-C APPLICATION USING A STEREO MINI-JACK Figure 2 FULL-DUPLEX CIRCUIT USING NEGATIVE-CHARGE STORAGE Figure 3 NOTE: The capacitor stores negative charge whenever the TXD signal from the PC serial port is in a marking data state (a negative voltage that is typically -10 volts). The top DS275's TXOUT uses this negative charge reservoir when it is in a marking state. The capacitor will discharge to 0 volts when the TXD line is spacing (and TXOUT is still marking) at a time constant determined by its value and the value of the load resistance reflected back to TXOUT. However, when TXD is marking the capacitor will quickly charge back to -10 volts. Note that TXD remains in a marking state when idle, which improves the performance of this circuit. ABSOLUTE MAXIMUM RATINGS* VCC VDRV -0.3 to +7.0 volts -0.3 to +13.0 volts 4 of 8 DS275 RXIN TXIN TXOUT RXOUT Storage Temperature Operating Temperature * 15 volts -0.3 to VCC + 0.3 volts 15 volts -0.3 to VCC + 0.3 volts -55C to +125C 0C to 70C This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS PARAMETER Logic Supply Transmit Driver Supply Logic 1 Input Logic 0 Input RS-232 Input Range (RXIN) Dynamic Supply Current TXIN = VCC TXIN = GND Static Supply Current TXIN = VCC TXIN = GND Driver Leakage Current (VCC=0V) SYMBOL VCC VDRV VIH VIL VRS MIN 4.5 4.5 2.0 -0.3 -15 TYP 5.0 5-12 MAX 5.5 13.0 VCC+0.3 +0.8 +15 UNITS V V V V V IDRV1 ICC1 IDRV1 ICC1 400 40 3.8 40 800 100 5.0 100 A A A A 3 IDRV2 ICC2 IDRV2 ICC2 1.5 10.0 3.8 10.0 10.0 15.0 5.0 20.0 A A mA A 4 IDRV3 0.05 1.0 A 5 5 of 8 NOTES 1 1 2 DS275 DC ELECTRICAL CHARACTERISTICS (0C to 70C; VCC = VDRV = 5V =10%) PARAMETER TXOUT Level High TXOUT Level Low TXOUT Short Circuit Current TXOUT Output Slew Rate Propagation Delay RXIN Input Threshold Low RXIN Input Threshold High RXIN Threshold Hysteresis RXOUT Output Current @ 2.4V RXOUT Output Current @ 0.4V SYMBOL VOTXH VOTXL ISC tSR tPD VTL VTH VHYS IOH IOL MIN 3.5 -8.5 0.8 1.6 0.5 -1.0 TYP 4.0 -9.0 +60 5 1.2 2.0 0.8 MAX 5.0 +85 30 1.6 2.4 3.2 NOTES: 1. VDRV must be greater than or equal to VCC. 2. VCC = VDRV = 5V =10%. 3. See test circuit in Figure 4. 4. See test circuit in Figure 5. 5. See test circuit in Figure 6. 6. TXIN = VIL and TX OUT loaded by 3 k =to ground. 7. TXIN = VIH, RXIN = -10 volts and TXOUT loaded by 3 k =to ground. 8. TXIN to TXOUT - see Figure 7. 9. VHYS = VTH - VTL. 6 of 8 UNITS V V mA V/s s V V V mA mA NOTES 6 7 8 9 DS275 DYNAMIC OPERATING CURRENT TEST CIRCUIT Figure 4 DRIVER LEAKAGE TEST CIRCUIT Figure 6 STATIC OPERATING CURRENT TEST CIRCUIT Figure 5 7 of 8 DS275 PROPAGATION DELAY TEST CIRCUIT Figure 7 DS275E 14-PIN TSSOP DIM A MM A1 MM A2 MM B MM C MM D MM E MM e1 MM G MM H MM L MM phi 8 of 8 14-PIN MIN MAX 1.10 0.05 0.75 1.05 0.18 0.30 0.09 0.18 4.90 5.10 4.40 NOM 0.65 BSC 0.25 REF 6.25 6.55 0.50 0.70 0 8