TOTX170AF - TOSHIBA - Datasheet.Live

TOTX170A

2001-06-13

FIBER OPTIC TRANSMITTING MODULE

TOTX170A

FIBER OPTIC TRANSMITTING

MODULE FOR SIMPLEX DIGITAL

SIGNAL TRANSMISSION

 Data rate : DC to 6 Mb / s (NRZ code)

 Transmission distance : Up to 40 m

 TTL interface

 LED is driven by Differential cuicuit

1. Maximum Ratings (Ta = 25°C)

PARAMETER SYMBOL RATING UNIT

Storage Temperature Tstg −40 to 70 °C

Operating Temperature Topr −40 to 70 °C

Supply Voltage VCC −0.5 to 7 V

Input Voltage VIN

−0.5 to

VCC + 0.5 V

Soldering Temperature Tsol 260 (Note 1) °C

Note 1: Soldering time ≤ 3 s (More than 1 mm apart from the package).

Handling precaution: The LEDs used in this product contain GaAs (Gallium Arsenide).

Care must be taken to protect the safety of people and the

environment when scrapping or terminal processing.

Unit : mm

TOTX170A

2001-06-13

2. Recommended Operating Conditions

PARAMETER SYMBOL MIN TYP. MAX UNIT

Supply Voltage VCC 4.75 5.0 5.25 V

High Level Input Voltage VIH 2.0 ― V

CC V

Low Level Input Voltage VIL 0 ― 0.8 V

3. Electrical and Optical Characteristics (Ta = 25°C, VCC = 5 V)

PARAMETER SYMBOL CONDITION MIN TYP. MAX UNIT

Data Rate NRZ Code (Note 2) DC ― 6 Mb / s

Transmission Distance Using APF (Note 3) and TORX170 0.2 ― 40 m

Pulse Width Distortion (Note 4) Δtw

Using TORX170

Pulse width 165 ns

Pulse cycle 330 ns, CL = 10 pF

−55 ― 55 ns

Fiber Output Power Pf APF 2 m, R = 0 Ω (Note 5) −15 ― −9 dBm

Peak Emission Wavelength λp ― 650 ― nm

Current Consumption ICC R = 0 Ω ― 67 85 mA

High Level Input Voltage VIH 2.0 ― ― V

Low Level Input Voltage VIL ― ― 0.8 V

High Level Input Current IIH VI = 2.7 V ― ― 20 μA

Low Level Input Current IIL VI = 0.4 V ― ― −0.4 mA

Note 2: LED is on when input signal is high level, it is off when low level.

For data rate > 3 Mb / s, the duty factor must be kept 25 to 75%.

Note 3: All Plastic Fiber (980 / 1000 μm).

Note 4: Between input of TOTX170A and output of TORX170.

Note 5: Measure with a standard optical fiber with fiber optic connectors. Valued by peak.

TOTX170A

2001-06-13

4. Example of Typical Characteristics (Note 7)

Note 7: There give characteristic examples, and its values are not guaranteed.

TOTX170A

2001-06-13

Note 7: There give characteristic examples, and its values are not guaranteed.

TOTX170A

2001-06-13

5. Application Circuit

Note 6: Select a resistor value as follows :

(Ta = 25°C, VCC = 5 V)

TRANSMISSION DISTANCE

(m)

RESISTOR

(Ω)

0.2 to 15 8.2 k

15 to 30 2.4 k

30 to 40 0

6. Applicable Optical Fiber with Fiber Optic Connectors

TOCP100−□□B, TOCP155−□□B, TOCP100P−□□B, TOCP155P−□□B

TOTX170A

2001-06-13

7. Precautions during use

(1) Maximum rating

The maximum ratings are the limit values which must not be exceeded during operation of device.

None of these rating value must not be exceeded. If the maximum rating value is exceeded, the

characteristics of devices may never be restored properly. In extreme cases, the device may be

permanently damages.

(2) Lifetime of light emitters

If an optical module is used for a long period of time, degeneration in the characteristics will mostly

be due to a lowering of the fiber output power (Pf). This is caused by the degradation of the optical

output of the LEDs used as the light source. The cause of degradation of the optical output of the

LEDs may be defects in wafer crystallization or mold resin stress. The detailed causes are, however,

not clear.

The lifetime of light emitters is greatly influenced by the operating conditions and the environment in

which it is used as well as by the lifetime characteristics unique to the device type. Thus, when a light

emitting device and its operating conditions determined, Toshiba recommend that lifetime

characteristics be checked.

Depending on the environment conditions, Toshiba recommend that maintenance such as regular

checks of the amount of optical output in accordance with the condition of operating environment.

(3) Soldering

Optical modules are comprised of internal semiconductor devices. However, in principle, optical

modules are optical components. During soldering, ensure that flux does not contact with the emitting

surface or the detecting surface. Also ensure that proper flux removal is conducted after soldering.

Some optical modules come with a protective cap. The protective cap is used to avoid malfunction

when the optical module is not in use. Note that it is not dust or waterproof.

As mentioned before, optical modules are optical components. Thus, in principle, soldering where

there may be flux residue and flux removal after soldering is not recommended. Toshiba recommend

that soldering be performed without the optical module mounted on the board. Then, after the board

has been cleaned, the optical module should be soldered on to the board manually.

If the optical module cannot be soldered manually, use non−halogen (chlorine−free) flux and make

sure, without cleaning, there is no residue such as chlorine. This is one of the ways to eliminate the

effects of flux. In such a cases, be sure to check the devices’ reliability.

(4) Vibration and shock

This module is plastic sealed and has its wire fixed by resin. This structure is relatively resistant to

vibration and shock. In actual equipment, there are sometime cases in which vibration, shock, or

stress is applied to soldered parts or connected parts, resulting in lines cut. A care must be taken in

the design of equipment which will be subject to high levels of vibration.

(5) Attaching the fiber optic transmitting module

Solder the fixed pins (pins 4 and 5) of the fiber optic transmitting module TOTX170A to the printed

circuit board in order to fix it to the board.

(6) Solvent

When using solvent for flux removal, do not use a high acid or high alkali solvent. Be careful not to

pour solvent in to the optical connector ports. If solvent is inadvertently poured in to them, clean it off

using cotton tips.

(7) Protective cap

When the TOTX170A is not in use, attach the protective cap.

(8) Supply voltage

Use the supply voltage within the recommended operating condition (VCC = 5 ± 0.25 V). Make sure

that supply voltage does not exceed the maximum rating value of 7 V, even for an instant.

(9) Input voltage

If a voltage exceeding the maximum rating value (VCC + 0.5 V) is applied to the transmitter input,

the internal IC may suffer damage. If there is a possibility that excessive voltage due to surges may

be added to the input terminal, insert a protective circuit.

(10) Soldering condition

Solder at 260°C or less for no more than three seconds.

TOTX170A

2001-06-13

(11) Precautions when disposing of devices and packing materials.

When disposing devices and packing materials, follow the procedures stipulated by local regulations

in order to protect the environment against contamination.

Compound semiconductors such as GaAs are used as LED materials in this module. When devices are

disposed of, worker safety and protection of the environment must be taken into account.

(12) Precautions during use

Toshiba is continually working to improve the quality and the reliability of their products.

Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical

sensitivity and their vulnerability to physical stress. It is the responsibility of the buyer, when

utilizing Toshiba products, to observe standards of safety, and to avoid situations in which the

malfunction or failure of a Toshiba product could cause loss of human life, bodily injury or damage to

property.

When developing equipment, please ensure that Toshiba products are used within the specified

operating ranges set forth in the most recent product specifications. Also, please keep in mind the

precautions and conditions set forth in the Toshiba Semiconductor Reliability Handbook.

TOTX170A

2001-06-13

RESTRICTIONS ON PRODUCT USE 20070701-EN

• The information contained herein is subject to change without notice.

• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor

devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical

stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of

safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of

such TOSHIBA products could cause loss of human life, bodily injury or damage to property.

In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as

set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and

conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability

Handbook” etc.

• The TOSHIBA products listed in this document are intended for usage in general electronics applications

(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,

etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires

extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or

bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or

spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,

medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his

document shall be made at the customer’s own risk.

• The products described in this document shall not be used or embedded to any downstream products of which

manufacture, use and/or sale are prohibited under any applicable laws and regulations.

• The information contained herein is presented only as a guide for the applications of our products. No

responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which

may result from its use. No license is granted by implication or otherwise under any patents or other rights of

TOSHIBA or the third parties.

• GaAs(Gallium Arsenide) is used in this product. The dust or vapor is harmful to the human body. Do not break,

cut, crush or dissolve chemically.

• Please contact your sales representative for product-by-product details in this document regarding RoHS

compatibility. Please use these products in this document in compliance with all applicable laws and regulations

that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses

occurring as a result of noncompliance with applicable laws and regulations.