V15
2
SPECIFICATIONS
All Specifications Typical At Nominal Line, Full Load, and 25 Unless Otherwise Noted℃
INPUT SPECIFICATIONS: GENRAL SPECIFICATIONS:
Input Voltage Range ....………….......…......... 24V ................. 10-36V
Efficiency .................…..................................……..........…....... See Table
48V .................. 18-75V
Isolation Voltage ... Input/Output, Input/Case, Output/Case .. 1500VDC min.
Input Surge Voltage (100ms max.) ………….… 24
Isolation Resistance .............................…......................….... 10
7
ohm min.
48V .…..... 100Vdc max.
Isolation Capacitance …………………..…………………..… 2000pF typ.
Under Voltage Lockout ………..….. 24Vin power up …....……..…. 9.5V
Switching Frequency ........………….....................…………... 250KHz typ.
24Vin power down ……....…. 8.5V
Operating Case Temperature ..…..……..........….....……........ -40 to 100℃ ℃
48Vin power up ……...…..…. 17V
Storage Temperature ……………………….....……............ -55 to +105℃ ℃
48Vin power down ...….….…. 16V
Thermal Shutdown Case Temp. .…..……...……………..……. 110 typ.℃
Positive Logic Remote On/Off (see note4&5)
Humidity .................................................... 95% RH max. Non condensing
Input Filter ………………………………………………..…….…... Pi Type
MTBF ………. MIL-STD-217F, GB, 25 , Full Load ………… 600Khrs typ.℃
OUTPUT SPECIFICATIONS:
Dimensions ................................ 2.28x2.40x0.52 inches(57.9x61.0x13.2 mm)
Voltage Accuracy …......................................…………........ ±1.5% max.
Case Material ….............……....…… Aluminum Baseplate with Plastic Case
Transient Response: 25% Step Load Change .…………..……… <500µs
Weight ………………………………………………………………….……… 114g
External Trim Adj. Range (note6) …………………………..………. ±10%
NOTE:
Ripple & Noise, 20MHz BW (note3)
1. Measured from high line to low line.
3.3V & 5V ……..… 40mV RMS max., 100mV pk-pk max.
2. Measured from full load to zero load.
12V & 15V ………. 60mV RMS max., 150mV pk-pk max.
3. Output ripple and noise measured with 10uF tantalum and 1uF
24V ………........ 100mV RMS max., 240mV pk-pk max.
ceramic capacitor across output. (48V: 10uF aluminum and 1uF
28V ………….... 100mV RMS max., 280mV pk-pk max.
ceramic capacitor across output)
48V …………….. 150mV RMS max., 480mV pk-pk max.
4. Logic compatibility ……………... open collector ref to -Input
Temperature Coefficient ....................………......................... ±0.03%/°C
Module on …………….………... >3.5VDC to 75VDC or open circuit
Short Circuit Protection .........………………......................... Continuous
Module off ………………………………………………….. < 1.2VDC
Line Regulation (note1) ……………….………..................…. ±0.2% max.
5. Suffix "N" to the model number with negative logic remote on/off
Load Regulation (note2) ………………………….........…...... ±0.2% max.
Module on .……………….……………………………….…. < 1.2VDC
Over Voltage Protection Trip Range, % Vo nom. ................... 115-140%
Module off ..……………………. >3.5VDC to 75VDC or open circuit
Current Limit .................……….……….... 110%-150% Nominal Output
6. Trim-up ………….. connect a resistor between the trim pin and +Sense
Start up time ………………………….…….………………..…... 120ms typ.
Trim-down …….…. connect a resistor between the trim pin and -Sense
7. Suffix “-C” to the model number with clear mounting insert. (3.2mm DIA.)
8. An external input capacitor 470uF for 24Vin or 47uF for 48Vin models
are recommended to reduce input ripple voltage.
CASE HB
Tolerances Inches: X.XX= ±0.02 , X.XXX= ±0.010
Millimeters: X.X= ±0.5 , X.XX=±0.25
BOTTOM VIEW
All Dimensions In Inches(mm)
Mounting Inserts
M3*0.5 Through 4pl.
1
-Sense
-Vout
-Vin
CASE
ON/OFF
+Vout
+Sense
Trim
8
7
9
6
2
5
4
3
+Vin
Function
Pin
Remote On/Off Control
ON/OFF (2)
-VIN (4)
HIGH SIGNAL HERE
DISABLE OUTPUT
External Output Trim
VR
+SENSE (8)
TRIM (7)
-SENSE (6)
R1
R2
+SENSE (8)
TRIM (7)
-SENSE (6)
TRIM UP
TRIM DOWN