General Specifications
Flanged Attenuators
100 Watts
Model RFP-100-XXAMZ
Resistive Element: Thick film
Substrate: Beryllium oxide ceramic
Cover: Alumina ceramic
Mounting Flange: Copper nickel plated per
QQ-N-290
Lead(s): 99.99% pure silver (.005” thk)
Outline Drawing
(2 PLACES)
.130 DIA. THRU.
.110
.165
.050
.975
TYP.
.335
.125
.725
MAX.
.200
.187
.375
Notes: Tolerance is ±.010, unless otherwise specified. Operating
temperature is -55°C to +150°C (see chart). Designed to meet or
exceed applicable portions of MIL-E-5400. All dimensions are in
inches. Lead length 0.15” minimum.
Specifications subject to change without notice.
Electrical Specifications
Attenuation Value: 1, 2, 3, 4, 5, 6, 9, 10, 20 or
30 dB
Frequency Range: DC - 2.0 GHz
Power: 100 Watts
Flanged Attenuators
Features
DC - 2.0 GHz
100 Watts
BeO Ceramic
•Welded Silver Leads
Non-Nichrome Resistive
Element
Low VSWR
100% Tested
1
Sales Desk USA: Voice: (800) 544-2414 Fax: (315) 432-9121
Sales Desk Europe: Voice: (+44) 23 92 232392 Fax: (+44) 23 92 251369
Note: XX denotes attenuation value.
RFP
100-XX
AMZ
VER. 12/5/01
CASE TEMPERATURE — °C
% OF RATED POWER
150125100755025
100
75
25
50
0
Flanged Attenuators
Model RFP-100-XXAMZ
2
Sales Desk USA: Voice: (800) 544-2414 Fax: (315) 432-9121
Sales Desk Europe: Voice: (+44) 23 92 232392 Fax: (+44) 23 92 251369
Power Derating Suggested Mounting Procedures
SCALE:
WITH LEAD.
BOARD EVEN
MIN..025
(2 PLACES)
THAN LEAD.
SUGGESTED STRESS RELIEF METHODS
BOARD LOWER
1. Make sure that the devices are mounted on flat surfaces
(.001” under the device) to optimize the heat transfer.
2. Drill & tap the heatsink for the appropriate thread size to be
used.
3. Coat heatsink with a minimum amount of high quality
silicone grease (.001” max. thickness).
4. Position device on mounting surface and secure using
socket head screws, flat & split washers. Torque screws to
the appropriate value. Make sure that the device is flat
against the heatsink. (Care should be taken to avoid
upward pressure of the leads towards the lid).
5. Solder leads in place using an SN63 type solder with a
controlled temperature iron (210°C).
BOARD HIGHER
THAN LEAD.
THAN LEAD.
BOARD LOWER
SCALE:
NOT RECOMMENDED APPLICATION
Specifications
PART NUMBER ATTENUATION (dB) TOL. (+/-dB) POWER (WATTS) VSWR FREQ. (GHz)
RFP-100-1AMZ 1 0.75 100 1.50:1 1.0
RFP-100-2AMZ 2 0.75 100 1.45:1 1.0
RFP-100-3AMZ 3 0.75 100 1.35:1 1.0
RFP-100-4AMZ 4 0.75 100 1.25:1 1.0
RFP-100-5AMZ 5 0.75 100 1.25:1 1.0
RFP-100-6AMZ 6 0.75 100 1.20:1 1.0
RFP-100-9AMZ 9 0.50 100 1.20:1 1.0
RFP-100-10AMZ 10 0.50 100 1.20:1 2.0
RFP-100-20AMZ 20 0.50 100 1.20:1 1.0
RFP-100-30AMZ 30 1.50 100 1.20:1 1.0