Edition 2014-04-01 Published by Infineon Technologies AG, 81726 Munich, Germany. (c) 2014 Infineon Technologies AG All Rights Reserved. LEGAL DISCLAIMER THE INFORMATION GIVEN IN THIS APPLICATION NOTE IS GIVEN AS A HINT FOR THE IMPLEMENTATION OF THE INFINEON TECHNOLOGIES COMPONENT ONLY AND SHALL NOT BE REGARDED AS ANY DESCRIPTION OR WARRANTY OF A CERTAIN FUNCTIONALITY, CONDITION OR QUALITY OF THE INFINEON TECHNOLOGIES COMPONENT. THE RECIPIENT OF THIS APPLICATION NOTE MUST VERIFY ANY FUNCTION DESCRIBED HEREIN IN THE REAL APPLICATION. INFINEON TECHNOLOGIES HEREBY DISCLAIMS ANY AND ALL WARRANTIES AND LIABILITIES OF ANY KIND (INCLUDING WITHOUT LIMITATION WARRANTIES OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY) WITH RESPECT TO ANY AND ALL INFORMATION GIVEN IN THIS APPLICATION NOTE. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. CoolSETTMQ1 ICE2QR0665G Trademarks of Infineon Technologies AG AURIXTM, C166TM, CanPAKTM, CIPOSTM, CIPURSETM, EconoPACKTM, CoolMOSTM, CoolSETTM, CORECONTROLTM, CROSSAVETM, DAVETM, DI-POLTM, EasyPIMTM, EconoBRIDGETM, EconoDUALTM, EconoPIMTM, EconoPACKTM, EiceDRIVERTM, eupecTM, FCOSTM, HITFETTM, HybridPACKTM, IRFTM, ISOFACETM, IsoPACKTM, MIPAQTM, ModSTACKTM, my-dTM, NovalithICTM, OptiMOSTM, ORIGATM, POWERCODETM; PRIMARIONTM, PrimePACKTM, PrimeSTACKTM, PRO-SILTM, PROFETTM, RASICTM, ReverSaveTM, SatRICTM, SIEGETTM, SINDRIONTM, SIPMOSTM, SmartLEWISTM, SOLID FLASHTM, TEMPFETTM, thinQ!TM, TRENCHSTOPTM, TriCoreTM. Other Trademarks Advance Design SystemTM (ADS) of Agilent Technologies, AMBATM, ARMTM, MULTI-ICETM, KEILTM, PRIMECELLTM, REALVIEWTM, THUMBTM, VisionTM of ARM Limited, UK. AUTOSARTM is licensed by AUTOSAR development partnership. BluetoothTM of Bluetooth SIG Inc. CAT-iqTM of DECT Forum. COLOSSUSTM, FirstGPSTM of Trimble Navigation Ltd. EMVTM of EMVCo, LLC (Visa Holdings Inc.). EPCOSTM of Epcos AG. FLEXGOTM of Microsoft Corporation. FlexRayTM is licensed by FlexRay Consortium. HYPERTERMINALTM of Hilgraeve Incorporated. IECTM of Commission Electrotechnique Internationale. IrDATM of Infrared Data Association Corporation. ISOTM of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLABTM of MathWorks, Inc. MAXIMTM of Maxim Integrated Products, Inc. MICROTECTM, NUCLEUSTM of Mentor Graphics Corporation. MIPITM of MIPI Alliance, Inc. MIPSTM of MIPS Technologies, Inc., USA. muRataTM of MURATA MANUFACTURING CO., MICROWAVE OFFICETM (MWO) of Applied Wave Research Inc., OmniVisionTM of OmniVision Technologies, Inc. OpenwaveTM Openwave Systems Inc. RED HATTM Red Hat, Inc. RFMDTM RF Micro Devices, Inc. SIRIUSTM of Sirius Satellite Radio Inc. SOLARISTM of Sun Microsystems, Inc. SPANSIONTM of Spansion LLC Ltd. SymbianTM of Symbian Software Limited. TAIYO YUDENTM of Taiyo Yuden Co. TEAKLITETM of CEVA, Inc. TEKTRONIXTM of Tektronix Inc. TOKOTM of TOKO KABUSHIKI KAISHA TA. UNIXTM of X/Open Company Limited. VERILOGTM, PALLADIUMTM of Cadence Design Systems, Inc. VLYNQTM of Texas Instruments Incorporated. VXWORKSTM, WIND RIVERTM of WIND RIVER SYSTEMS, INC. ZETEXTM of Diodes Zetex Limited. Last Trademarks Update 2011-11-11 Data Sheet 3 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Revision History Major changes since previous revision Date Version 2014-04-01 2.1 Changed By Change Description Added VVCCPD and marking drawing. Revised typo, IVCCcharge1, IVCCcharge2, IZCMAX and outline dimension drawing. Upgraded the operating temperature from -25C to -40C. We Listen to Your Comments Is there any information in this document that you feel is wrong, unclear or missing? Your feedback will help us to continuously improve the quality of our documentation. Please send your proposal (including a reference to this document title/number) to: ctdd@infineon.com Data Sheet 4 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Table of Contents Revision History ...................................................................................................................................................4 Table of Contents .................................................................................................................................................5 1 1.1 1.2 Pin Configuration and Functionality ..............................................................................................7 Pin Configuration with PG-DSO-16/12...............................................................................................7 Pin Functionality.................................................................................................................................7 2 Representative Block Diagram .......................................................................................................8 3 3.1 3.2 3.3 3.3.1 3.3.1.1 3.3.1.2 3.3.2 3.3.2.1 3.3.3 3.4 3.4.1 3.5 3.5.1 3.5.2 3.5.3 3.6 Functional Description ....................................................................................................................9 VCC Pre-Charging and Typical VCC Voltage During Start-up...........................................................9 Soft-start ............................................................................................................................................9 Normal Operation.............................................................................................................................10 Digital Frequency Reduction.......................................................................................................10 Up/down counter....................................................................................................................10 Zero crossing (ZC counter) ....................................................................................................11 Ringing suppression time............................................................................................................12 Switch on determination ........................................................................................................12 Switch Off Determination ............................................................................................................12 Current Limitation.............................................................................................................................12 Foldback Point Correction...........................................................................................................13 Active Burst Mode Operation ...........................................................................................................14 Entering Active Burst Mode Operation........................................................................................14 During Active Burst Mode Operation ..........................................................................................14 Leaving Active Burst Mode Operation ........................................................................................14 Protection Functions ........................................................................................................................15 4 4.1 4.2 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.3.5 4.3.6 4.3.7 4.3.8 4.3.9 4.3.10 Electrical Characteristics ..............................................................................................................17 Absolute Maximum Ratings .............................................................................................................17 Operating Range..............................................................................................................................17 Characteristics .................................................................................................................................18 Supply Section ............................................................................................................................18 Internal Voltage Reference .........................................................................................................18 PWM Section ..............................................................................................................................19 Current Sense.............................................................................................................................19 Soft Start.....................................................................................................................................19 Foldback Point Correction...........................................................................................................19 Digital Zero Crossing ..................................................................................................................20 Active Burst Mode.......................................................................................................................20 Protection....................................................................................................................................21 TM CoolMOS Section ....................................................................................................................21 6 Input power curve ..........................................................................................................................24 8 Marking ...........................................................................................................................................26 Data Sheet 5 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Off-Line SMPS Quasi-Resonant PWM Controller with integrated 650V CoolMOSTM and startup cell in DSO-16/12 Product Highlights Active Burst Mode to reach the lowest standby power requirement <100mW @ no load Quasi resonant operation Digital frequency reduction for better overall system efficiency Integrated 650V startup cell Pb-free lead plating, halogen free mold compound, RoHS compliant Features * * * * * * * * * PG-DSO-16/12 TM 650V avalanche rugged CoolMOS with built-in startup cell Quasi resonant operation till very low load Active burst mode operation for low standby input power (< 0.1W) Digital frequency reduction with decreasing load for reduced switching loss Built-in digital soft-start Foldback point correction and cycle-by-cycle peak current limitation Maximum on time limitation Auto restart mode for VCC over-voltage protection, under-voltage protection, over-load protection and overtemperature protection Latch-off mode for adjustable output over-voltage protection and transformer short-winding protection Description (R) TM The CoolSET -Q1 series (ICE2QRxx65G) is the first generation of quasi-resonant controller and CoolMOS integrated power IC. Operating the MOSFET switch in quasi-resonant mode, lower EMI, higher efficiency and lower voltage stress on secondary diodes are expected for the SMPS. Based on the BiCMOS technology, the (R) CoolSET -Q1 series has a wide operation range (up to 25V) of IC power supply and lower power consumption. It also offers many advantages such as quasi-resonant operation till very low load, increasing the higher average system efficiency compared to other conventional solutions, achieving ultra-low power consumption with small and controllable output voltage ripple at standby mode with Active Burst Mode operation, etc. Applications Adapter/Charger LCD monitor, DVD R/W, DVD Combo, Blue-ray/DVD player, Set-top box Auxiliary power supply for PC, Printer, TV, Home theater/Audio System, etc. Figure 1 Typical Application Type ICE2QR0665G Package PG-DSO-16/12 Marking ICE2QR0665G VDS 650V 1 VDS 0.65 2 2 230VAC 15% 85-265 VAC 79W 45W 1 typ @ T=25C 2 Calculated maximum input power rating at Ta=50C, Ti=125C and without copper area as heat sink. Data Sheet 6 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Pin Configuration and Functionality 1 Pin Configuration and Functionality 1.1 Pin Configuration with PGDSO-16/12 Table 1 1.2 ZC (Zero Crossing) At this pin, the voltage from the auxiliary winding after a time delay circuit is applied. Internally, this pin is connected to the zero-crossing detector for switch-on determination. Additionally, the output overvoltage detection is realized by comparing the voltage Vzc with an internal preset threshold. Pin configuration Pin Symbol 1 ZC Zero Crossing 2 FB Feedback 3 N.C. 4 CS 5 Drain 6 Drain 7 Drain Function FB (Feedback) Normally an external capacitor is connected to this pin for a smooth voltage VFB. Internally this pin is connected to the PWM signal generator block for switch-off determination (together with the current sensing signal), to the digital signal processing block for the frequency reduction with decreasing load during normal operation, and to the Active Burst Mode controller block for entering Active Burst Mode operation determination and burst ratio control during Active Burst Mode operation. Additionally, the open-loop / over-load protection is implemented by monitoring the voltage at this pin. Not Connected Current Sense/ 1 TM 650V CoolMOS Source 1) TM Drain 1) TM Drain 1) TM Drain 1) TM Drain 650V CoolMOS 650V CoolMOS 650V CoolMOS 8 Drain 650V CoolMOS 9 N.C. Not Connected 10 N.C. Not Connected 11 VCC Controller Supply Voltage 12 GND Controller Ground Pin Functionality CS (Current Sense) This pin is connected to the shunt resistor for the primary current sensing externally and to the PWM signal generator block for switch-off determination (together with the feedback voltage) internally. Moreover, short-winding protection is realized by monitoring the voltage Vcs during on-time of the main power switch. TM Drain (Drain of integrated CoolMOS ) Drain pin is the connection to the drain of the TM. internal CoolMOS VCC (Power supply) VCC pin is the positive supply of the IC. The operating range is between VVCCoff and VVCCOVP. GND (Ground) This is the common ground of the controller. Figure 2 1 Pin configuration PG-DSO-16/12 (top view) at Tj=110C Data Sheet 7 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Representative Block Diagram 2 Representative Block Diagram Figure 3 Representative Block Diagram Data Sheet 8 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Functional Description 3 Functional Description 3.1 VCC Pre-Charging and Typical VCC Voltage During Start-up TM In ICE2QR0665G, a startup cell is integrated into the CoolMOS . As shown in Figure 3, the start cell consists of a high voltage device and a controller, whereby the high voltage device is controlled by the controller. The startup cell provides a pre-charging of the VCC capacitor till VCC voltage reaches the VCC turned-on threshold VVCCon and the IC begins to operate. Once the mains input voltage is applied, a rectified voltage shows across the capacitor Cbus. The high voltage device provides a current to charge the VCC capacitor Cvcc. Before the VCC voltage reaches a certain value, the amplitude of the current through the high voltage device is only determined by its channel resistance and can be as high as several mA. After the VCC voltage is high enough, the controller controls the high voltage device so that a constant current around 1mA is provided to charge the VCC capacitor further, until the VCC voltage exceeds the turned-on threshold VVCCon. As shown as the time phase I in Figure 4, the VCC voltage increase near linearly and the charging speed is independent of the mains voltage level. Figure 4 VCC voltage at start up The time taking for the VCC pre-charging can then be approximately calculated as: where IVCCcharge2 is the charging current from the startup cell which is 1.05mA, typically. When the VCC voltage exceeds the VCC turned-on threshold VVCCon at time t1, the startup cell is switched off and the IC begins to operate with soft-start. Due to power consumption of the IC and the fact that there is still no energy from the auxiliary winding to charge the VCC capacitor before the output voltage is built up, the VCC voltage drops (Phase II). Once the output voltage is high enough, the VCC capacitor receives the energy from the auxiliary winding from the time point t2 onward. The VCC then will reach a constant value depending on output load. 3.2 Soft-start As shown in Figure 5, at the time ton, the IC begins to operate with a soft-start. By this soft-start the switching TM stresses for the switch, diode and transformer are minimized. The soft-start implemented in CoolSET Q1 is a digital time-based function. The preset soft-start time is tSS (12ms) with 4 steps. If not limited by other functions, the peak voltage on CS pin will increase step by step from 0.32V to 1V finally. Data Sheet 9 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Functional Description Figure 5 Maximum current sense voltage during soft start 3.3 Normal Operation The PWM controller during normal operation consists of a digital signal processing circuit including an up/down counter, a zero-crossing counter (ZC counter) and a comparator, and an analog circuit including a current measurement unit and a comparator. The switch-on and -off time points are each determined by the digital circuit and the analog circuit, respectively. As input information for the switch-on determination, the zerocrossing input signal and the value of the up/down counter are needed, while the feedback signal V FB and the current sensing signal VCS are necessary for the switch-off determination. Details about the full operation of the PWM controller in normal operation are illustrated in the following paragraphs. 3.3.1 Digital Frequency Reduction As mentioned above, the digital signal processing circuit consists of an up/down counter, a ZC counter and a comparator. These three parts are key to implement digital frequency reduction with decreasing load. In addition, a ringing suppression time controller is implemented to avoid mis-triggering by the high frequency oscillation, when the output voltage is very low under conditions such as soft start period or output short circuit. Functionality of these parts is described as in the following. 3.3.1.1 Up/down counter The up/down counter stores the number of the zero crossing where the main power switch is switched on after demagnetization of the transformer. This value is fixed according to the feedback voltage, V FB, which contains information about the output power. Indeed, in a typical peak current mode control, a high output power results in a high feedback voltage, and a low output power leads to a low regulation voltage. Hence, according to V FB, the value in the up/down counter is changed to vary the power MOSFET off-time according to the output power. In the following, the variation of the up/down counter value according to the feedback voltage is explained. The feedback voltage VFB is internally compared with three threshold voltages VFBZL, VFBZH and VFBR1, at each clock period of 48ms. The up/down counter counts then upward, keep unchanged or count downward, as shown in Table 2. Table 2 Operation of the up/down counter VFB up/down counter action Always lower than VFBZL Count upwards till 7 Once higher than VFBZL, but always lower than VFBZH Stop counting, no value changing Once higher than VFBZH, but always lower than VFBR1 Count downwards till 1 Once higher than VFBR1 Set up/down counter to 1 Data Sheet 10 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Functional Description In the ICE2QR0665G, the number of zero crossing is limited to 7. Therefore, the counter varies between 1 and 7, and any attempt beyond this range is ignored. When VFB exceeds VFBR1 voltage, the up/down counter is reset to 1, in order to allow the system to react rapidly to a sudden load increase. The up/down counter value is also reset to 1 at the start-up time, to ensure an efficient maximum load start up. Figure 6 shows some examples on how up/down counter is changed according to the feedback voltage over time. The use of two different thresholds VFBZL and VFBZH to count upward or downward is to prevent frequency jittering when the feedback voltage is close to the threshold point. However, for a stable operation, these two thresholds must not be affected by the foldback current limitation (see section 3.4.1), which limits the V CS voltage. Hence, to prevent such situation, the threshold voltages, VFBZL and VFBZH, are changed internally depending on the line voltage levels. Figure 6 Up/down counter operation 3.3.1.2 Zero crossing (ZC counter) In the system, the voltage from the auxiliary winding is applied to the zero-crossing pin through a RC network, which provides a time delay to the voltage from the auxiliary winding. Internally this pin is connected to a clamping network, a zero-crossing detector, an output overvoltage detector and a ringing suppression time controller. During on-state of the power switch a negative voltage applies to the ZC pin. Through the internal clamping network, the voltage at the pin is clamped to certain level. The ZC counter has a minimum value of 0 and maximum value of 7. After the internal MOSFET is turned off, every time when the falling voltage ramp of on ZC pin crosses the VZCCT (100mV) threshold, a zero crossing is detected and ZC counter will increase by 1. It is reset every time after the DRIVER output is changed to high. The voltage VZC is also used for the output overvoltage protection. Once the voltage at this pin is higher than the threshold VZCOVP during off-time of the main switch, the IC is latched off after a fixed blanking time. To achieve the switch-on at voltage valley, the voltage from the auxiliary winding is fed to a time delay network (the RC network consists of Dzc, Rzc1, Rzc2 and Czc as shown in Figure 1) before it is applied to the zero-crossing detector through the ZC pin. The needed time delay to the main oscillation signal t should be approximately one fourth of the oscillation period, Tosc (by transformer primary inductor and drain-source capacitor) minus the propagation delay from the detected zero-crossing to the switch-on of the main switch tdelay. Data Sheet 11 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Functional Description This time delay should be matched by adjusting the time constant of the RC network which is calculated as: 3.3.2 Ringing suppression time After MOSFET is turned off, there will be some oscillation on VDS, which will also appear on the voltage on ZC pin. To avoid mis-triggering by such oscillations to turn on the MOSFET, a ringing suppression timer is implemented. This suppression time is depended on the voltage VZC. If the voltage VZC is lower than the threshold VZCRS, a longer preset time tZCRS2 is applied. However, if the voltage VZC is higher than the threshold, a shorter time tZCRS1 is set. 3.3.2.1 Switch on determination After the gate drive goes to low, it cannot be changed to high during ring suppression time. After ring suppression time, the gate drive can be turned on when the ZC counter value is higher or equal to up/down counter value. However, it is also possible that the oscillation between primary inductor and drain-source capacitor damps very fast and IC cannot detect enough zero crossings and ZC counter value will not be high enough to turn on the gate drive. In this case, a maximum off time is implemented. After gate drive has been remained off for the period of TOffMax, the gate drive will be turned on again regardless of the counter values and V ZC. This function can effectively prevent the switching frequency from going lower than 20kHz. Otherwise it will cause audible noise during start up. 3.3.3 Switch Off Determination In the converter system, the primary current is sensed by an external shunt resistor, which is connected between low-side terminal of the main power switch and the common ground. The sensed voltage across the shunt resistor VCS is applied to an internal current measurement unit, and its output voltage V1 is compared with the regulation voltage VFB. Once the voltage V1 exceeds the voltage VFB, the output flip-flop is reset. As a result, the main power switch is switched off. The relationship between the V1 and the VCS is described by: To avoid mis-triggering caused by the voltage spike across the shunt resistor at the turn on of the main power switch, a leading edge blanking time, tLEB, is applied to the output of the comparator. In other words, once the gate drive is turned on, the minimum on time of the gate drive is the leading edge blanking time. In addition, there is a maximum on time, tOnMax, limitation implemented in the IC. Once the gate drive has been in high state longer than the maximum on time, it will be turned off to prevent the switching frequency from going too low because of long on time. 3.4 Current Limitation There is a cycle by cycle current limitation realized by the current limit comparator to provide an over-current detection. The source current of the MOSFET is sensed via a sense resistor R CS. By means of RCS the source current is transformed to a sense voltage VCS which is fed into the pin CS. If the voltage VCS exceeds an internal voltage limit, adjusted according to the Mains voltage, the comparator immediately turns off the gate drive. To prevent the Current Limitation process from distortions caused by leading edge spikes, a Leading Edge Blanking time (tLEB) is integrated in the current sensing path. Data Sheet 12 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Functional Description A further comparator is implemented to detect dangerous current levels (V CSSW) which could occur if one or more transformer windings are shorted or if the secondary diode is shorted. To avoid an accidental latch off, a spike blanking time of tCSSW is integrated in the output path of the comparator. 3.4.1 Foldback Point Correction When the main bus voltage increases, the switch on time becomes shorter and therefore the operating frequency is also increased. As a result, for a constant primary current limit, the maximum possible output power is increased which is beyond the converter design limit. To avoid such a situation, the internal foldback point correction circuit varies the V CS voltage limit according to the bus voltage. This means the VCS will be decreased when the bus voltage increases. To keep a constant maximum input power of the converter, the required maximum VCS versus various input bus voltage can be calculated, which is shown in Figure 7. Figure 7 Variation of the VCS limit voltage according to the IZC current According to the typical application circuit, when MOSFET is turned on, a negative voltage proportional to bus TM voltage will be coupled to auxiliary winding. Inside CoolSET Q1, an internal circuit will clamp the voltage on ZC pin to nearly 0V. As a result, the current flowing out from ZC pin can be calculated as When this current is higher than IZC_FS, the amount of current exceeding this threshold is used to generate an offset to decrease the maximum limit on VCS. Since the ideal curve shown in Figure 7 is a nonlinear one, a digital block in CoolSETTM Q1 is implemented to get a better control of maximum output power. Additional advantage to use digital circuit is the production tolerance is smaller compared to analog solutions. The typical maximum limit on VCS versus the ZC current is shown in Figure 8. Data Sheet 13 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Functional Description Figure 8 VCS-max versus IZC 3.5 Active Burst Mode Operation At light load condition, the IC enters Active Burst Mode operation to minimize the power consumption. Details about Active Burst Mode operation are explained in the following paragraphs. 3.5.1 Entering Active Burst Mode Operation For determination of entering Active Burst Mode operation, three conditions apply: the feedback voltage is lower than the threshold of VFBEB (1.25V). Accordingly, the peak current sense voltage across the shunt resistor is 0.17V; the up/down counter is NZC_ABM (7) and a certain blanking time tBEB (24ms). Once all of these conditions are fulfilled, the Active Burst Mode flip-flop is set and the controller enters Active Burst Mode operation. This multi-condition determination for entering Active Burst Mode operation prevents mistriggering of entering Active Burst Mode operation, so that the controller enters Active Burst Mode operation only when the output power is really low during the preset blanking time. 3.5.2 During Active Burst Mode Operation After entering the Active Burst Mode the feedback voltage rises as VOUT starts to decrease due to the inactive PWM section. One comparator observes the feedback signal if the voltage level V FBBOn (3.6V) is exceeded. In that case the internal circuit is again activated by the internal bias to start with switching. Turn-on of the power MOSFET is triggered by the timer. The PWM generator for Active Burst Mode operation composes of a timer with a fixed frequency of fsB (52kHz, typical) and an analog comparator. Turn-off is resulted if the voltage across the shunt resistor at CS pin hits the threshold VcsB (0.34V). A turn-off can also be triggered if the duty ratio exceeds the maximal duty ratio DmaxB (50%). In operation, the output flip-flop will be reset by one of these signals which come first. If the output load is still low, the feedback signal decreases as the PWM section is operating. When feedback signal reaches the low threshold VFBBOff (3.0V), the internal bias is reset again and the PWM section is disabled until next time regulation signal increases beyond the VFBBOn (3.6V) threshold. If working in Active Burst Mode the feedback signal is changing like a saw tooth between VFBBOff and VFBBOn shown in Figure 9. 3.5.3 Leaving Active Burst Mode Operation The feedback voltage immediately increases if there is a high load jump. This is observed by a comparator. As the current limit is 34% during Active Burst Mode a certain load is needed so that feedback voltage can exceed VFBLB (4.5V). After leaving active burst mode, maximum current can now be provided to stabilize V O. In addition, Data Sheet 14 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Functional Description the up/down counter will be set to 1 immediately after leaving Active Burst Mode. This is helpful to decrease the output voltage undershoot. Figure 9 Signals in Active Burst Mode 3.6 Protection Functions The IC provides full protection functions. The following table summarizes these protection functions. Table 3 Protection features VCC Over-voltage VCC Under-voltage Over-load/Open Loop Over-temperature Output Over-voltage Short Winding Auto Restart Mode Auto Restart Mode Auto Restart Mode Auto Restart Mode Latched Off Mode Latched Off Mode During operation, the VCC voltage is continuously monitored. In case of an under-voltage or an over-voltage, the IC is reset and the main power switch is then kept off. After the VCC voltage falls below the threshold Data Sheet 15 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Functional Description VVCCoff, the startup cell is activated. The VCC capacitor is then charged up. Once the voltage exceeds the threshold VVCCon, the IC begins to operate with a new soft-start. In case of open control loop or output over load, the feedback voltage will be pulled up. After a blanking time of tOLP_B (30ms), the IC enters auto-restart mode. The blanking time here enables the converter to provide a peak power in case the increase in VFB is due to a sudden load increase. This output over load protection is disabled during burst mode. During off-time of the power switch, the voltage at the zero-crossing pin is monitored for output over-voltage detection. If the voltage is higher than the preset threshold VZCOVP, the IC is latched off after the preset blanking time tZCOVP. This latch off mode can only be reset if the Vcc < VVCCPD. If the junction temperature of IC controller exceeds TjCon (130 C), the IC enters into OTP auto restart mode. This OTP is disabled during burst mode. If the voltage at the current sensing pin is higher than the preset threshold VCSSW during on-time of the power switch, the IC is latched off. This is short-winding protection. The short winding protection is disabled during burst mode. During latch-off protection mode, the VCC voltage drops to VVCCoff (10.5V) and then the startup cell is activated. The VCC voltage is then charged to VVCCon (18V). The startup cell is shut down again. This action repeats again and again. TM There is also a maximum on time limitation implemented inside the CoolSET Q1. Once the gate voltage is high and longer than tOnMax, the switch is turned off immediately. Data Sheet 16 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Electrical Characteristics 4 Electrical Characteristics Note : All voltages are measured with respect to ground (Pin 12). The voltage levels are valid if other ratings are not violated. 4.1 Absolute Maximum Ratings Note : Absolute maximum ratings are defined as ratings, which when being exceeded may lead to destruction of the integrated circuit. For the same reason it needs to make sure that any capacitor that will be connected to pin 11 (VCC) is discharged before assembling the application circuit. Parameter Symbol Limit Values Unit min. max. VDS - 650 V Switching drain current, pulse width tp limited by Tjmax IS - 9.95 A Pulse drain current, tp limited by Tjmax ID_Puls - 15.75 A Avalanche energy, repetitive tAR 1 limited by max. Tj=150C EAR - 0.47 mJ Avalanche current, repetitive tAR 1 limited by max. Tj=150C IAR - 2.5 A VVCC -0.3 27 V FB Voltage VFB -0.3 5.5 V ZC Voltage VZC -0.3 5.5 V CS Voltage VCS -0.3 5.5 V IZCMAX - 3 mA Junction Temperature Tj -40 150 C Storage Temperature TS -55 150 C Thermal Resistance Junction -Ambient RthJA - 110 K/W ESD Capability (incl. Drain Pin) VESD - 2 kV Drain Source Voltage VCC Supply Voltage Current out from ZC pin 4.2 Remarks Tj=110C Controller & TM CoolMOS Human body 2 model Operating Range Note : Within the operating range the IC operates as described in the functional description. Parameter VCC Supply Voltage Symbol VVCC Limit Values min. max. VVCCoff VVCCOVP Unit Remarks V 1 Repetitive avalanche causes additional power losses that can be calculated as PAV=EAR*f 2 According to EIA/JESD22-A114-B (discharging a 100pF capacitor through a 1.5kW series resistor) Data Sheet 17 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Electrical Characteristics Junction Temperature of Controller TjCon -40 130 C Junction Temperature of TM CoolMOS TjCoolMOS -40 150 C 4.3 Characteristics 4.3.1 Supply Section Limited by over temperature protection Note : The electrical characteristics involve the spread of values within the specified supply voltage and junction temperature range Tj from - 40 C to 125 C. Typical values represent the median values, which are related to 25C. If not otherwise stated, a supply voltage of VCC = 18 V is assumed. Parameter Symbol Limit Values Unit Test Condition min. typ. max. IVCCstart - 300 550 A VVCC =VVCCon -0.2V IVCCcharge1 - 1.22 5.0 mA VVCC = 0V IVCCcharge2 0.8 1.1 - mA VVCC = 1V IVCCcharge3 - 1 - mA VVCC =VVCCon -0.2V Maximum Input Current of TM Startup Cell and CoolMOS IDrainIn - - 2 mA VVCC =VVCCon -0.2V Leakage Current of TM Startup Cell and CoolMOS IDrainLeak - 0.2 50 A VDrain = 600V at Tj=100C Supply Current in normal operation IVCCNM - 1.5 2.3 mA IFB = 0A Supply Current in Auto Restart Mode with Inactive Gate IVCCAR - 300 - A IFB = 0A Supply Current in Latch-off Mode IVCClatch - 300 - A IFB = 0A Supply Current in Burst Mode with inactive Gate IVCCburst - 500 950 A VFB = 2.5V, exclude the current flowing out from FB pin VCC Turn-On Threshold VVCCon 17.0 18.0 19.0 V VCC Turn-Off Threshold VVCCoff 9.8 10.5 11.2 V VCC Turn-On/Off Hysteresis VVCChys - 7.5 - V Start Up Current VCC Charge Current 4.3.2 Internal Voltage Reference Parameter Internal Reference Voltage Data Sheet Symbol VREF Limit Values min. typ. max. 4.80 5.00 5.20 18 Unit V Test Condition Measured at pin FB IFB=0 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Electrical Characteristics 4.3.3 PWM Section Parameter Symbol Limit Values Unit min. typ. max. RFB 14 23 33 k PWM-OP Gain GPWM 3.18 3.3 - - Offset for Voltage Ramp VPWM 0.6 0.7 - V Maximum on time in normal operation tOnMax 22 30 41 s Feedback Pull-Up Resistor 4.3.4 Current Sense Parameter Symbol Limit Values min. typ. max. Unit Peak current limitation in normal operation VCSth 0.97 1.03 1.09 V Leading Edge Blanking time tLEB 200 330 460 ns Peak Current Limitation in Active Burst Mode VCSB 0.29 0.34 0.39 V 4.3.5 Test Condition Soft Start Parameter Soft-Start time Symbol Limit Values min. typ. max. 8.5 12 - tSS Unit soft-start time step - 3 - ms Internal regulation voltage at first step VSS1 1 - 1.76 - V Internal regulation voltage step at soft start VSS_S - 0.56 - V 4.3.6 1 Test Condition ms 1 tSS_S Foldback Point Correction Parameter Symbol ZC current first step threshold Limit Values Unit min. typ. max. IZC_FS 0.35 0.5 0.621 mA ZC current last step threshold IZC_LS 1.3 1.7 2.2 mA CS threshold minimum VCSMF - 0.66 - V 1 Test Condition Test Condition Izc=2.2mA, VFB=3.8V The parameter is not subjected to production test - verified by design/characterization Data Sheet 19 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Electrical Characteristics 4.3.7 Digital Zero Crossing Parameter Symbol Limit Values min. typ. max. Unit Test Condition Zero crossing threshold voltage VZCCT 50 100 170 mV Ringing suppression threshold VZCRS - 0.7 - V Minimum ringing suppression time tZCRS1 1.62 2.5 4.5 s VZC > VZCRS Maximum ringing suppression time tZCRS2 - 25 - s VZC < VZCRS Threshold to set Up/Down Counter to one VFBR1 - 3.9 - V Threshold for downward counting at low line VFBZHL - 3.2 - V Threshold for upward counting at low line VFBZLL - 2.5 - V Threshold for downward counting at high line VFBZHH - 2.9 - V Threshold for upward counting at high line VFBZLH - 2.3 - V ZC current for IC switch threshold to high line IZCSH - 1.3 - mA ZC current for IC switch threshold to low line IZCSL - 0.8 - mA tCOUNT - 48 - ms tOffMax 30 42 57.5 s Counter time 1 Maximum restart time in normal operation 4.3.8 Active Burst Mode Parameter Symbol Limit Values Unit min. typ. max. VFBEB - 1.25 - NZC_ABM - 7 - tBEB - 24 - ms Feedback voltage for leaving Active Burst Mode VFBLB - 4.5 - V Feedback voltage for burst-on VFBBOn - 3.6 - V Feedback voltage for burst-off VFBBOff - 3.0 - V Feedback voltage for entering Active Burst Mode Minimum Up/down value for entering Active Burst Mode Blanking time for entering Active Burst Mode 1 Test Condition V The parameter is not subjected to production test - verified by design/characterization Data Sheet 20 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Electrical Characteristics Fixed Switching Frequency in Active Burst Mode Max. Duty Cycle in Active Burst Mode 4.3.9 fsB 39 52 65 DmaxB - 0.5 - kHz Protection Parameter Symbol VCC overvoltage threshold Limit Values Unit min. typ. max. VVCCOVP 24.0 25.0 26.0 V Over Load or Open Loop Detection threshold for OLP protection at FB pin VFBOLP - 4.5 - V Over Load or Open Loop Protection Blanking Time tOLP_B 20 30 44 ms Output Overvoltage detection threshold at the ZC pin VZCOVP 3.55 3.7 3.84 V Blanking time for Output Overvoltage protection tZCOVP - 100 - s Threshold for short winding protection VCSSW 1.63 1.68 1.78 V Blanking time for short-winding protection tCSSW - 190 - ns TjCon 130 140 150 C VVCCPD 5.2 - 7.8 V Over temperature protection 1 Power Down Reset threshold for Latched Mode Test Condition After Latched Off Mode is entered Note : The trend of all the voltage levels in the Control Unit is the same regarding the deviation except VVCCOVP & VVCCPD. CoolMOSTM Section 4.3.10 Parameter Drain Source Breakdown Voltage Symbol Limit Values Rise Time Fall Time 1 2 Test Condition typ. max. V(BR)DSS 650 - - V Tj = 110C RDSon - 0.65 1.37 0.75 1.58 Tj = 25C 1 Tj=125C at ID = 2.5A - pF VDS = 0V to 480V Drain Source On-Resistance Effective output capacitance, energy related Unit min. 1 Co(er) - 26 trise - 30 2 30 2 tfall - - ns - ns The parameter is not subjected to production test - verified by design/characterization Measured in a Typical Flyback Converter Application Data Sheet 21 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Electrical Characteristics 5 Typical CoolMOSTM Performance Characteristic Figure 10 Safe Operating Area (SOA) curve for ICE2QR0665G Figure 11 Power dissipation; Ptot=f(Ta) Data Sheet 22 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Electrical Characteristics Figure 12 Data Sheet Drain-source breakdown voltage; VBR(DSS)=f(Tj) 23 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Input power curve 6 Input power curve Two input power curves gives typical input power versus ambient temperature are showed below; Vin=85~265Vac (Figure 13) and Vin=230Vac (Figure 14). The curves are derived based on a typical discontinuous mode flyback model which considers either 50% duty ratio or 115V maximum secondary to primary reflected voltage (high priority). The calculation is based on no copper area as heatsink for the device. The input power already includes power loss at input common mode choke and bridge rectifier and the TM CoolMOS . The device saturation current (ID_plus@Tj=125C) is also considered. To estimate the out power of the device, it is simply multiplying the input power at a particular ambient temperature with the estimated efficiency for the application. For example, a wide range input voltage (Figure 13), operating temperature is 50 C, estimated efficiency is 85%,the output power is 38W (45W*0.85). Figure 13 Input Power curve Vin=85~265Vac; Pin=f(Ta) Figure 14 Input Power curve Vin=230Vac; Pin=f(Ta) Data Sheet 24 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Input power curve 7 Outline Dimension Figure 15 Data Sheet PG-DSO-16/12 (Pb-free lead plating Plastic Dual Small Outline Package) 25 V2.1, 2014-04-01 CoolSETTMQ1 ICE2QR0665G Marking 8 Marking Figure 16 Marking for ICE2QR0665G Data Sheet 26 V2.1, 2014-04-01 w w w . i n f i n e o n . c o m Published by Infineon Technologies AG Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Infineon: ICE2QR0665G