U.FL-2LP-088K1T-A-(200) - HIROSE(HRS)

1

Ultra Small Surface Mount Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated Height

U.FL Series

2004.2

1.9(2.0Max)

2.4(2.5Max)

3(3.2Max)

U.FL-LP(V)-040

U.FL-LP-040

U.FL-LP-066

E.FL-LP-040

E.FL-LP-066

U.FL E.FL

2.5Max

2.0Max2.4Max2.4Max

U.FL-LP-040

Plug

Cable

U.FL-LP-066

U.FL-LP(V)-040

U.FL-LP-062

U.FL-LP-088

U.FL-R-SMT

Receptacle

U.FL-R-SMT

Receptacle

U.FL-R-SMT

Receptacle

U.FL-R-SMT

Receptacle

U.FL-R-SMT

Receptacle

Dia.0.81

Dia.1.32

Dia.1.13

Dia.0.81

Dia.1.00

Dia.1.37

■Features

1.Extremely Small Occupied Mounting Area

Reduced board space requirement by 18% to 7.7mm2, when

compared with Hirose’s E.FL connectors.

2.Light Weight

One of the world’s lightest coaxial connectors.

Receptacle: 15.7mg

3.Frequencies of Up to 6GHz

To meet the frequency requirements of a wide variety of

miniature equipment, these connectors offer high frequency

performance from DC to 6 GHz.

4.Board Placement with Automatic Equipment

Supplied on tape-and-reel packaging.

5.Use of Ultra-fine Teflon Cable

Several of ultra-fine single and double shielded Teflon®

coaxial cables terminate to U.FL plug.

6. Simple Disconnection

Dedicated tool allows reliable un-mating of the plug.

7.User Friendly Mating Operation

Tactile lock feeling ensures and confirms reliable connection.

■Applications

Mobile phones, Wireless LAN, Mini-PCI, Bluetooth, PDA, GPS,

electronic measuring instruments, etc.

*Teflon is a registered trademark of DuPont.

Mated Height Comparison

(With E.FL series)

●Space Factor of Mated Connector

Up to 6GHz Transmission Speed

NEW

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

2

■Product Specifications

*V.S.W.R. Measurement System

The above V.S.W.R. standard values were measured using the measurement connection shown below.

Note 1: Cable type connectors were measured with SMA conversion adapters

attached to both ends of the harness product of a suitable 100cm cable.

Note 2: Board type connectors were mounted to a 50Ωglass epoxy board and

measurements were conducted with SMA conversion adapters attached.

Ratings

Nominal characteristic impedance

Voltage rating

Frequency range

50 ohms

60 V AC (rms)

DC to 6 GHz

Operating temperature range

Operating humidity

-40˚C to +90˚C

90% max.

Part Material Finish Remarks

Shell Phosphor bronze Silver plated —————

Male center contact Brass Gold plated —————

Female center contact Phosphor bronze Gold plated —————

Insulator Plug Color: Black UL94V-0

Receptacle Color: Beige UL94V-0LCP

PBT

■Material/Finishes

1. Contact resistance

2. Insulation resistance

3. Withstanding voltage

4. V.S.W.R.*

5. Center contact holding force

6. Durability

(mating/un-mating,

with corresponding plug)

7. Vibration

8. Shock

9. Humidity

(Steady state)

10. Temperature cycle

11. Salt spray test

Item Specification Conditions

Center: 20 m ohms max.

Outside: 10 m ohms max.

500 M ohms min.

No flashover or insulation breakdown.

0.15 N min.

Contact resistance

Center: 25 m ohms max.

Outside: 15 m ohms max.

No electrical discontinuity of 1µs min.

No damage, cracks or parts dislocation.

Insulation resistance 100 M ohms min.(when humidity high)

Insulation resistance 500 M ohms min.(when dry)

No damage, cracks or parts dislocation.

Contact resistance:25 m ohms max. (Center)

15 m ohms max. (Outside)

No excessive corrosion

10 mA max.

100 V DC

200 V AC / 1 minute

Measured with a Ø 0.475 pin gauge

30 cycles

Frequency: 10 to 100 Hz, single amplitude of 1.5mm, acceleration

of 59m/s

2

, for 5 cycles in the direction of each of the 3 axis.

Acceleration of 735 m/s2, 11ms duration, sine half-wave

waveform, 6 cycles in each of 3 axes.

96 hours at temperature of 40ç and humidity of 95%.

Temperature:-40˚C

/

+5 to +35˚C

/

+90˚C

/

+5 to +35˚C

Time: 30

/

5 max.

/

30

/

5 max.

(Minutes)

5 cycles

5% salt water solution, 48 hours

Part No. Up to 3GHz 3 to 6GHz

U.FL-LP-040 dia.0.81mm Coaxial Cable Assembly 1.3 Max 1.35 Max

U.FL-LP(V)-040 dia.0.81mm Coaxial Cable Assembly 1.3 Max 1.3 Max

U.FL-LP-068 dia.1.13mm Coaxial Cable Assembly 1.3 Max 1.4 Max

U.FL-LP-066 dia.1.32mm Coaxial Cable Assembly 1.3 Max 1.5 Max

U.FL-LP-062 dia.1mm Coaxial Cable Assembly 1.3 Max 1.3 Max

U.FL-LP-088 dia.1.37mm Coaxial Cable Assembly 1.3 Max 1.4 Max

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

3

Part No.

U.FL-R-SMT(01)

U.FL-R-SMT(10)

CL No.

331-0471-0-01

331-0471-0-10

Packaging

Bag packaging (100 pieces/bag)

Reel packaging (2500 pieces/reel)

Weight (mg)

15.7/unit

■Receptacles

Note 1: Receptacles of (01) specification are sold by the

bag with 100 pieces per bag.

Please order in pack units.

Note 2: Receptacles of (10) specification are sold by the

reel (which contains 2,500 pieces).

Please order in reel units.

Note 3: This area may be covered by insulating material.

●Packaging Specifications

Embossed Carrier Tape Dimensions

Reel Dimensions

GND GND

GND

Cut Out Prohibition Area

Recommended PCB mounting pattern

SIG

Ø2

3

2.6

0.6

1.25

0.35

1.05±0.05 1±0.05

1±0.05

2.2±0.05

4±0.05

1.9±0.05

1.2Max(Note 3)

(3.1)

2.6

1.8

1.75±0.1

12±0.3

8±0.1

2±0.1 4±0.1 0.3

1.6

Center contact

Unreeling direction

5.5±0.1

Ø1.5

+0.1

0

1.8 14

Ø13

Ø21

Ø330±2

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

4

Part No.

Mated Height

Applicable

cable

Weight (mg)

2.5mm Max. 2.5mm Max. 2.0mm Max. 2.4mm Max. 2.4mm Max.

(2.4mm Nom.) (2.4mm Nom.) (1.9mm Nom.) (2.3mm Nom.) (2.3mm Nom.)

Dia. 0.81mm Dia. 0.81mm Dia. 1mm Dia. 1.37mm

Coaxial cable Coaxial cable Coaxial cable Coaxial cable

53.7 59.1 34.8 45.5 71.7

Dia. 1.13mm and

Dia. 1.32mm

Coaxial cable

■Cable Assemb ly (Plug)

●Cable Guide

U.FL-LP-040 U.FL-LP-062 U.FL-LP-088

Dia.0.81mm

Coaxial Cable 04 7/0.05 SA

(AWG36)

Dia.0.40

PFA

Single

Shield SA

Dia.0.81

PFA 50 ohms 6.45dB/m 9.42dB/m

Dia.1.13mm

Coaxial Cable 068 7/0.08 SA

(AWG32)

Dia.0.68

FEP

Single

Shield SA[TA]

Dia.1.13

FEP 50 ohms 3.43dB/m

[3.73dB/m]

5.13dB/m

[5.44dB/m]

Dia.1.32mm

Coaxial Cable 066 7/0.08 SA

(AWG32)

Dia.0.66

FEP

Double

Shield TA

Dia.1.32

FEP 50 ohms 3.8dB/m 5.6dB/m

Dia.1mm

Coaxial Cable 062 7/0.071 SA

(AWG33)

Dia.0.62

FEP

Tape, single

Shield TAT

Dia.1

FEP 50 ohms 3.1dB/m 4.4dB/m

Dia.1.37mm

Coaxial Cable

(data as provided by cable suppliers, for reference only)

* SA : Silver plated annealed copper wire, TA : Tin plated annealed copper wire, TAT : Tin plated copper wire alloyed with tin

088 7/0.102 SA

(AWG30)

Dia.0.88

FEP

Single

Shield TA

Dia.1.37

FEP 50 ohms 2.8dB/m 4.3dB/m

Description Cable

Type

Cable Specification

Inner

Conductor*

Dielectric

Diameter

Outer

Conductor*

Jacket

Diameter

Nominal

Impedance

Nominal attenuation

At 3GHz At 6GHz

3

4

1.93

5

3

1.85

U.FL-LP-066

4

3

1.93

U.FL-LP(V)-040

3.4

2.8

1.5

4

2.8

1.8

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

5

■How to Specify Plug Cable Assembly

Dimensions of U.FL Series assembly products should be made as indicated below.

Double-Ended Cable Assembly Single-Ended Cable Assembly

U.FL - [] LP - [] - A - (L)

●Ordering Information

Series name U.FL

Total Length(mm)

00350<

=L<

=00200

02000<L<

=00500

05000<L<

<

=01000

10000<0L<

=1000

Standard Tolerance (mm)

±04

±08

±12

±1.5%

●

Total Standard Tolerance for Total Length of Cable Assembly

Note: Shortest length L is 35 mm.

L

31 2 4

1

Assembly type LP: Single ended

2LP: Double ended

2

Cable type 04 : Dia.0.81mm Coaxial Cable

068 : Dia.1.13mm Coaxial Cable

066 : Dia.1.32mm Coaxial Cable

062 : Dia.1 mm Coaxial Cable

088 : Dia.1.37mm Coaxial Cable

3

Total Length(mm) Length is expressed in mm units.

Please contact Hirose Sales Representative for cable length and cable end treatment.

4

Part No. of Plug

Part No. of Cable Assembly

Description

U.FL-LP-040

U.FL-LP-068

U.FL-LP-066

U.FL-LP(V)-040

U.FL-LP-062

U.FL-LP-088

U.FL-2LP-04N1-A-(L)

U.FL-2LP-04N2-A-(L)

U.FL-LP-04N1-A-(L)

U.FL-LP-04N2-A-(L)

U.FL-2LP-068N1-A-(L)

U.FL-2LP-068N2-A-(L)

U.FL-LP-068N1-A-(L)

U.FL-LP-068N2-A-(L)

U.FL-2LP-066J1-A-(L)

U.FL-2LP-066J2-A-(L)

U.FL-LP-066J1-A-(L)

U.FL-LP-066J2-A-(L)

U.FL-2LP(V)-04N1-A-(L)

U.FL-2LP(V)-04N2-A-(L)

U.FL-LP(V)-04N1-A-(L)

U.FL-LP(V)-04N2-A-(L)

U.FL-2LP-062N1D-A-(L)

U.FL-2LP-062N2D-A-(L)

U.FL-LP-062N1D-A-(L)

U.FL-LP-062N2D-A-(L)

U.FL-2LP-088K1T-A-(L)

U.FL-2LP-088K2T-A-(L)

U.FL-LP-088K1T-A-(L)

U.FL-LP-088K2T-A-(L)

Dia. 0.81mm double ended coaxial cable, color: white

Dia. 0.81mm double ended coaxial cable, color: black

Dia. 0.81mm single ended coaxial cable, color: white

Dia. 0.81mm single ended coaxial cable, color: black

Dia. 1.13mm double ended coaxial cable, color: gray

Dia. 1.13mm double ended coaxial cable, color: black

Dia. 1.13mm single ended coaxial cable, color: gray

Dia. 1.13mm single ended coaxial cable, color: black

Dia. 1.32mm double ended coaxial cable, color: gray

Dia. 1.32mm double ended coaxial cable, color: black

Dia. 1.32mm single ended coaxial cable, color: gray

Dia. 1.32mm single ended coaxial cable, color: black

Dia. 0.81mm double ended coaxial cable, color: white

Dia. 0.81mm double ended coaxial cable, color: black

Dia. 0.81mm single ended coaxial cable, color: white

Dia. 0.81mm single ended coaxial cable, color: black

Dia. 1mm double ended coaxial cable, color: gray

Dia. 1mm double ended coaxial cable, color: black

Dia. 1mm single ended coaxial cable, color: gray

Dia. 1mm single ended coaxial cable, color: black

Dia. 1.37mm double ended coaxial cable, color: gray

Dia. 1.37mm double ended coaxial cable, color: black

Dia. 1.37mm single ended coaxial cable, color: gray

Dia. 1.37mm single ended coaxial cable, color: black

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

6

Part No.

HRMP-U.FLJ

CL No.

311-0300-2

■Conversion Adapters

●SMA Conversion Adapter

(Mating portion: U.FL side jack - SMA side plug)

Note:

The U.FL side mating portions has a lower lock retention

force than the regular product, therefore, cannot be used

for purposes other than performance measurements.

(10.7) 8HEX

Part No.

U.FL-R-1

CL No.

331-0466-0

■Receptacle Inspection

This receptacle is used for inspecting the continuity, withstand

voltage, and other aspects of the harness product.

This receptacle is used for check the continuity, withstanding

voltage, and other performance of the cable assembly products.

Note: Part No. U.FL-LP-N-2 for U.FL-LP-040/066/088.

Part No. U.FL-LP(V)-N-2 for U.FL-LP(V)-040/U.FL-LP-062.

12.9

57HEX

M5∞0.5

1

(7.9)

(4.4)

Part No.

U.FL-LP-N-2

U.FL-LP(V)-N-2

CL No.

331-0494-5

331-0493-2

■Plug Extraction Tool

This jig is used for extraction from a mating condition.

U.FL

Ø15

(90)

50

5

2.1

Part No.

HRMJ-U.FLP

CL No.

311-0301-5

●SMA Conversion Adapter

(Mating portion: U.FL side plug - SMA side jack)

Note:

The U.FL side mating portions has a lower lock retention

force than the regular product, therefore, cannot be used

for purposes other than performance measurements.

14.05

Ø6.35

1/4-36UNS-2A

6 5.6(4.05)

Part No.

HRMJ-U.FLP-ST1

CL No.

311-0385-5

●SMA Conversion Adapter

(Mating portion: U.FL side plug-SMA side jack)

Note: This connector is used by compressing the mated

portion of U.FL side onto the U.FL-R-SMT portion.

(18.6)

1/4-36UNS-2A

65.5

(4)

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

7

■Usage Precautions

1. Plugs

(1) Connection/

disconnection of

connectors

(2) Permissible load on

the cable after

connector are mated.

(3) Precautions

1) To disconnect connectors, insert the end portion of U.FL-LP-N-2 and U.FL-LP(V)-N-2 under the connector flanges

and pull off vertically, in the direction of the connector mating axis.

2) To mate the connectors, the mating axes of both connectors must be

aligned and the connectors can be mated. The "click" will confirm fully

mated connection.Do not attempt to insert on an extreme angle.

After the connectors are mating, do not apply a load to the cable in excess of the values indicated in the diagram

below.

Do NOT forcefully twist or deform wires.

(1) Recommended

soldering temperature

profile

1) The temperature profile indicates the board surface temperature at the point of contacts with the connector

terminals.

2) The temperature profile will change depending on conditions which include such factors as the size of the board,

the solder used, and the solder thickness.

(3) Recommended screen

thickness 0.1 to 0.15 mm

(2) Recommended

manual soldering Manual soldering: 350˚C for 5 seconds

2. Receptacles

U.FL-LP-040 2N max.

2N max.

4N max.

U.FL-R-SMT

Temperature on

Top Portion of Part

Time

Preheating

(130 to 165ç)

Within 2 minutes

40 to 50

seconds

Heating peak

240ç 3 seconds

183ç

260

240

220

200

180

160

140

120

100

80

(ç)

Extraction Jig

U.FL-R-SMT

U.FL Cable

Assembly

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.