RCWPM (Military M/D55342)
www.vishay.com Vishay Dale
Revision: 22-Nov-12 1Document Number: 31010
For technical questions, contact: ff2aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Thick Film Chip Resistors, Military/Established Reliability
MIL-PRF-55342 Qualified, Type RM
FEATURES
Fully conforms to the requirements of
MIL-PRF-55342
Established reliability - verified failure rate; M, P, R, U, S,
V, and T levels
Construction is sulfur impervious against a high sulfur
environment (ASTM B 809-95 test method)
100 % group A screening per MIL-PRF-55342
Termination style B - tin/lead wraparound over nickel
barrier
Operating temperature range is - 55 °C to + 150 °C
For MIL-PRF-32159 zero ohm jumpers, see Vishay Dale’s
RCWPM Jumper (Military M32159) datasheet
(www.vishay.com/doc?31028)
Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
Notes
DSCC has created a series of drawings to support the need for 0201-sized product. Vishay Dale is listed as a resource on this drawing as
follows:
This drawing can be viewed at: www.landandmaritime.dla.mil/Programs/MilSpec/ListDwgs.aspx?DocTYPE=DSCCdwg.
(1) Continuous working voltage shall be or maximum working voltage, whichever is less.
(2) Characteristics: K = ± 100 ppm/°C; L = ± 200 ppm/°C; M = ± 300 ppm/°C.
(3) MIL case size 0705 and EIA case size 0805 are dimensionally the same.
MECHANICAL SPECIFICATIONS
Resistive element Ruthenium oxide
Encapsulation Epoxy
Substrate 96 % alumina
Termination Solder-coated nickel barrier
Solder finish Tin/lead solder alloy
STANDARD ELECTRICAL SPECIFICATIONS
VISHAY DALE
MODEL
MIL-PRF-55342
STYLE
MIL
SPEC.
SHEET
TERM. CASE
SIZE
POWER
RATING
P70 °C
W
MAX.
WORKING
VOLTAGE (1)
V
RESISTANCE
RANGE
TOLERANCE
± %
TEMPERATURE
COEFFICIENT (2)
± ppm/°C
RCWPM-0502 RM0502 01 B 0502 0.05 40 1 to 9.1 2, 5, 10 300
10 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-550 RM0505 02 B 0505 0.125 40 1 to 9.1 2, 5, 10 300
10 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-5100 RM1005 03 B 1005 0.20 75 1 to 5.6 2, 5, 10 300
5.62 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-5150 RM1505 04 B 1505 0.15 125 1 to 5.6 2, 5, 10 300
5.62 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-7225 RM2208 05 B 2208 0.225 175 1 to 5.6 2, 5, 10 300
5.62 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-575 RM0705 06 B
0705
(3) 0.15 50 1 to 5.6 2, 5, 10 300
5.62 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-1206 RM1206 07 B 1206 0.25 100 1 to 5.6 2, 5, 10 300
5.62 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-2010 RM2010 08 B 2010 0.80 150 1 to 5.6 2, 5, 10 300
5.62 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-2512 RM2512 09 B 2512 1.0 200 1 to 5.6 2, 5, 10 300
5.62 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-1100 RM1010 10 B 1010 0.50 75 1 to 5.6 2, 5, 10 300
5.62 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-0402 RM0402 11 B 0402 0.05 30 1 to 9.1 2, 5, 10 300
10 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-0603 RM0603 12 B 0603 0.10 50 1 to 5.6 2, 5, 10 300
5.62 to 22M 1, 2, 5, 10 100, 200, 300
RCWPM-0302 RM0302 13 B 0302 0.04 15 1 to 9.1 2, 5, 10 300
10 to 22M 1, 2, 5, 10 100, 200, 300
DSCC DRAWING
NUMBER
VISHAY DALE
MODEL TERM.
POWER RATING
P70 °C
W
RES. RANGE
RES. TOL.
± %
TEMP. COEF.
± ppm/°C
MAX. WORKING
VOLTAGE (1)
V
07009 RCWP-0201 B 0.05 10 to 46.4
47 to 1M 1, 5 200
100 30
P x R
RCWPM (Military M/D55342)
www.vishay.com Vishay Dale
Revision: 22-Nov-12 2Document Number: 31010
For technical questions, contact: ff2aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
For additional information on packaging, refer to the Surface Mount Resistor Packaging document (www.vishay.com/doc?31543).
(1) Products with space level failure rates are only offered in packaging codes with ESD overpack and labeling. For all other failure rates, the
ESD pack codes are an optional type of packaging.
(2) Failure rates U and V require group A and B inspection ran on each production lot.
(3) MIL spec option 1, 2, and 3 part marking is not offered for the slash sheet 01, 02, 11, and 13 sizes.
GLOBAL PART NUMBER INFORMATION
New Global Part Numbering: M55342M02B10E0RWB (preferred part number format)
MIL
STYLE CHARACTERISTICS SPEC.
SHEET
TERMINATION
STYLE
VALUE AND
TOLERANCE
FAILURE
RATE PACKAGING
(1)
SPECIAL
D55342
applies to
Style 07
(RM1206)
only.
M55342
applies to
all other
styles.
K = 100 ppm
L = 200 ppm
M = 300 ppm
(see Standard
Electrical
Specifications
table)
B = Pre-tinned
nickel barrier,
wraparound
(see Tolerance
and Multipliers
table)
C = Non-ER
M = 1.0 %/1000 h
P = 0.1 %/1000 h
R = 0.01 %/1000 h
U = 0.01 %/1000 h (2)
S = 0.001 %/1000 h
V = 0.001 %/1000 h (2)
T = Space level
TP =
Tin/lead,
T/R (full)
TN
= Tin/lead,
T/R (full), w/ESD
UL
= Tin/lead, T/R
single lot date code
S3
= Tin/lead,
T/R (1000 pieces)
SV
= Tin/lead, T/R
(1000 pieces), w/ESD
WB
= Tin/lead,
waffle tray
WA
= Tin/lead,
waffle tray,
w/ESD
WL
= Tin/lead,
waffle tray,
single lot date code
S2
= Tin/lead,
T/R (500 pieces)
SU
= Tin/lead, T/R
(500 pieces), w/ESD
S6
= Tin/lead,
T/R (300 pieces)
ST
= Tin/lead, T/R
(300 pieces), w/ESD
Blank =
Standard
(Dash number)
(Up to 1 digits)
S =
Space level
w/option 1 part
marking (-97) (3)
T =
Space level (-98)
2 =
Option 1
part marking
(-20) (3)
3 =
Options 2 and 3
part marking
(-30) (3)
Historical Part Numbering: M55342M02B10E0R (will continue to be accepted)
M55342 M 02 B 10E0 R WB
MIL
STYLE CHARACTERISTICS SPEC. SHEET TERMINATION
STYLE
VALUE AND
TOLERANCE
FAILURE
RATE
PACKAGING
CODE
RESISTANCE TOLERANCE AND MULTIPLIERS
TOLERANCE
MULTIPLIER VALUE
RANGE ()
± 1 % ± 2 % ± 5 % ± 10 %
DG J M 1 1 to 9xx
E H K N 1000 1K to 9xxK
F T L P 1 000 000 1M to 22M
Examples: 11D3 = 11.3 ± 1 %
10E0 = 10 k ± 1 %
332D = 332 ± 1 %
2F21 = 2.21 M ± 1 %
51G0 = 51 ± 2 %
10H0 = 10 k ± 2 %
33H0 = 33 k ± 2 %
22T0 = 22 M ± 2 %
15J0 = 15 ± 5 %
10K0 = 10 k ± 5 %
560K = 560 k ± 5 %
8L20 = 8.2 M ± 5 %
10M0 = 10 ± 10 %
10N0 = 10 k ± 10 %
2P70 = 2.7 M ± 10 %
8P20 = 8.2 M ± 10 %
55342M02MB10E0R W B
RCWPM (Military M/D55342)
www.vishay.com Vishay Dale
Revision: 22-Nov-12 3Document Number: 31010
For technical questions, contact: ff2aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DIMENSIONS in inches (millimeters)
VISHAY DALE
MODEL
MIL-PRF-55342
STYLE
MIL
SPEC.
SHEET
A
(LENGTH)
B
(WIDTH)
C
(HEIGHT)
D
(TOP TERM)
E
(BOTTOM TERM)
RCWPM-0502 RM0502 01 0.055 ± 0.005
(1.40 ± 0.13)
0.023 ± 0.003
(0.58 ± 0.08)
0.015 ± 0.003
(0.38 ± 0.08)
0.010 ± 0.005
(0.25 ± 0.13)
0.015 ± 0.005
(0.38 ± 0.13)
RCWPM-550 RM0505 02 0.055 ± 0.005
(1.40 ± 0.13)
0.050 ± 0.005
(1.27 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.010 ± 0.005
(0.25 ± 0.13)
0.015 ± 0.005
(0.38 ± 0.13)
RCWPM-5100 RM1005 03 0.105 ± 0.005
(2.67 ± 0.13)
0.050 ± 0.005
(1.27 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.015 ± 0.005
(0.38 ± 0.13)
0.015 ± 0.005
(0.38 ± 0.13)
RCWPM-5150 RM1505 04 0.155 ± 0.005
(3.94 ± 0.13)
0.050 ± 0.005
(1.27 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.015 ± 0.005
(0.38 ± 0.13)
0.015 ± 0.005
(0.38 ± 0.13)
RCWPM-7225 RM2208 05 0.230 ± 0.005
(5.84 ± 0.13)
0.075 ± 0.005
(1.91 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
RCWPM-575 RM0705 06 0.080 ± 0.005
(2.03 ± 0.13)
0.050 ± 0.005
(1.27 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.016 ± 0.008
(0.41 ± 0.20)
0.015 ± 0.005
(0.38 ± 0.13)
RCWPM-1206 RM1206 07 0.125 ± 0.005
(3.18 ± 0.13)
0.063 ± 0.005
(1.60 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.015 ± 0.005
(0.38 ± 0.13)
0.015 ± 0.005
(0.38 ± 0.13)
RCWPM-2010 RM2010 08 0.197 ± 0.006
(5.00 ± 0.15)
0.098 ± 0.005
(2.49 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
RCWPM-2512 RM2512 09 0.250 ± 0.005
(6.35 ± 0.13)
0.124 ± 0.005
(3.15 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
RCWPM-1100 RM1010 10 0.105 ± 0.005
(2.67 ± 0.13)
0.100 ± 0.005
(2.54 ± 0.13)
0.020 ± 0.005
(0.51 ± 0.13)
0.015 ± 0.005
(0.38 ± 0.13)
0.015 ± 0.005
(0.38 ± 0.13)
RCWPM-0402 RM0402 11 0.039 ± 0.003
(0.99 ± 0.08)
0.020 ± 0.003
(0.51 ± 0.08)
0.013 ± 0.003
(0.33 ± 0.08)
0.010 ± 0.005
(0.25 ± 0.13)
0.010 ± 0.005
(0.25 ± 0.13)
RCWPM-0603 RM0603 12 0.063 ± 0.005
(1.60 ± 0.13)
0.032 ± 0.005
(0.81 ± 0.13)
0.018 ± 0.005
(0.46 ± 0.13)
0.012 ± 0.005
(0.30 ± 0.13)
0.015 ± 0.005
(0.38 ± 0.13)
RCWPM-0302 RM0302 13 0.034 ± 0.004
(0.86 ± 0.10)
0.021 ± 0.003
(0.53 ± 0.08)
0.013 ± 0.003
(0.33 ± 0.08)
0.007 ± 0.005
(0.18 ± 0.13)
0.008 ± 0.005
(0.20 ± 0.13)
RCWP-0201 0.024 ± 0.002
(0.61 ± 0.05)
0.012 ± 0.002
(0.30 ± 0.05)
0.009 ± 0.002
(0.23 ± 0.05)
0.006 ± 0.003
(0.15 ± 0.08)
0.006 + 0.002 - 0.004
(0.15 + 0.05 - 0.10)
D
C
AE
B
DERATING CURVE
- 55 - 25 75 100 125 150 175
120
100
80
60
40
20
0
Ambient Temperature in °C
70
Rated Power in %
05025
CAGE CODE: 91637 and SH903
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 02-Oct-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.