BAW-M18MI-UAC50B-S04G - Balluff, Inc.

1.96

M12×1

flush

0...10 V

0.5...2 mm

BAW M12MI-UAC20B-S04G

24 V DC

15…30 V DC

3.60 V DC @ 24 V DC

10.0 mA

1.50 mm

1.25 ± 0.125 mm

0.01 V per 0.0015 mm

± 0.045 mm

0.000375 mm/°K

-10…+70 °C

500 Hz

1.0 ms

2 kW

250 V AC

IP 67

nickel plated brass

PA 12

M12 DC Micro

yes

Analog Sensors

M8, M12, M18, M30

PG 36, 80×80×40

Inductive

Sensors

Technical Description

Inductive sensing technology

is widely recognized for its

ruggedness and stability

under extreme industrial

conditions. Balluff

ULTRALINEARTM analog

sensors take advantage of

inductive technology's

strengths to bring you

precision non-contact

position measurement in an

affordable family of compact

housings. For applications

involving relatively short

travel of metal targets, there

is no better solution.

ULTRALINEARTM analog

sensors are simple three-

wire devices that operate on

24 V DC. They provide an

electrical signal that varies in

proportion to the position of

a metal target within the

working range. The linear

analog signal is available in

either voltage or current.

The ULTRALINEARTM family:

precision measurements in

hostile environments.

Features

Linear analog output

provides exact position

measurement

0...10 VDC or 0...20 mA

analog outputs available

Reliable measurements in

the harshest environments

(just like our rugged

inductive sensors)

No setup required, apply

power and it's ready

Totally self-contained

units, no separate

amplifier

Full range of housing sizes

provide a fit for any

application

Status LED warns if target

is outside the

measurement zone

Fully protected against

short circuit, overload and

polarity reversal.

0016A003

Analog

Output

Measurement

Range

10V

20mA

10mA

0mA

Min.

Active

Range

Mid.

Active

Range

Max.

Active

Range

Status LED Off Status LED On

Output Signals

Housing size

Mounting

Output signal

Linear range sl

Ordering code

Voltage output, 0 - 10V

Current output, 0 - 20mA

Current output, 4 - 20mA

Rated operational voltage Ue

Supply voltage UB

Supply voltage ripple, max. 15% of Ue

No-load supply current I0 @ U e

Linear span sL 1

Midpoint of linear range se 2

Resolution 3, voltage output

Resolution 3, current output

Non-linearity 4

Repeatability 5

Temperature drift 6 (+15…55 °C )

Ambient temperature range Ta

Cutoff frequency (-3 dB output amplitude)

Time delay before availability tv

Load resistance RL

Rated insulation voltage Ui

Degree of protection per IEC 529

Housing material

Sensing face material

Conductors (cable versions)

Connector (connector versions)

Linear range display (LED ON when out of range)

Short circuit/overload protected

Protected against polarity reversal

Notes:

1. Size of the linear sensing window

2. Midpoint with tolerance, sensor to sensor

3. Change in output per change in target movement

4. Deviation over the linear span, 3% of full scale

5. Ability to repeat output level for a given target

distance, 3% of full scale

6. Deviation relative to 25 °C ambient temperature

As a percent of full scale:

+15…55 °C = 1%

+10…60 °C = 2.5%

-10…+70 °C = 5%

7. For pigtail connector, replace -BP05 with -BP0.2-

GS04

M8×1

flush

0...10 V

0.5...1.5 mm

BAW M08EI-UAD15B-BP05

24 V DC

15…30 V DC

3.60 V DC @ 24 V DC

8.0 mA

1.00 mm

1.00 ± 0.1 mm

0.01 V per 0.001 mm

± 0.03 mm

0.00025 mm/°K

-10…+70 °C

1000 Hz

1.0 ms

2 kW

250 V AC

IP 67

stainless steel

PBTP

5 m unshielded PUR cable (3 x 26 AWG)

M12 DC Micro 7

yes

1.97

M18×1

flush

0...10 V

1...5 mm

BAW M18ME-UAC50B-BP05

0016A002

BK Analog Out

1BN

Quick Disconnect

Cable Out

Analog Out

M12×1

flush

0...10 V, 0-20 mA

0.5...2 mm

BAW M12MG2-UAC20B-BP05

BAW M12MG2-IAC20B-BP05

24 V DC

15…30 V DC

3.60 V DC @ 24 V DC

10.0 mA

1.50 mm

1.25 ± 0.125 mm

0.01 V per 0.0015 mm

0.02 mA per 0.0015 mm

± 0.045 mm

0.000375 mm/°K

-10…+70 °C

500 Hz

1.0 ms

2 k

250 V AC

IP 67

nickel plated brass

PA 12

5 m unshielded PUR cable (3 x 22 AWG)

M12 DC Micro 7

yes

Wiring Diagram

M12×1

non flush

0...10 V

1...4 mm

BAW M12MF2-UAC40F-BP05

24 V DC

15…30 V DC

3.60 V DC @ 24 V DC

10.0 mA

3.00 mm

1.25 ± 0.125 mm

0.01 V per 0.003 mm

± 0.09 mm

0.00075 mm/°K

-10…+70 °C

500 Hz

1.0 ms

2 k

250 V AC

IP 67

nickel plated brass

PBTP

5 m unshielded PUR cable (3 x 22 AWG)

M12 DC Micro 7

yes

M18×1

flush

0...10 V, 0-20 mA, 4-20 mA

1...5 mm

BAW M18MI-UAC50B-S04G

BAW M18MI-IAC50B-S04G

BAW M18MI-ICC50B-S04G

24 V DC

15…30 V DC

3.60 V DC @ 24 V DC

10.0 mA

4.00 mm

3.00 ± 0.3 mm

0.01 V per 0.004 mm

0.02 (0.016) mA per 0.004 mm

± 0.12 mm

0.001 mm/°K

-10…+70 °C

500 Hz

1.0 ms

2 kW

75 V DC

IP 67

nickel plated brass

PBTP

M12 DC Micro

yes

M18×1

flush

0...10 V

1...5 mm

BAW M18ME-UAC50B-S04G

24 V DC

15…30 V DC

3.60 V DC @ 24 V DC

10.0 mA

4.00 mm

3.00 ± 0.3 mm

0.01 V per 0.004 mm

± 0.12 mm

0.001 mm/°K

-10…+70 °C

500 Hz

1.0 ms

2 kW

75 V DC

IP 67

nickel plated brass

PBTP

M12 DC Micro

yes

24 V DC

15…30 V DC

3.60 V DC @ 24 V DC

10.0 mA

4.00 mm

3.00 ± 0.3 mm

0.01 V per 0.004 mm

± 0.12 mm

0.001 mm/°K

-10…+70 °C

500 Hz

1.0 ms

2 k

75 V DC

IP 67

nickel plated brass

PBTP

5 m unshielded PUR cable (3 x 22 AWG)

M12 DC Micro7

yes

Analog Sensors

M8, M12, M18, M30

PG 36, 80×80×40

Inductive

Sensors

Depending on ambient electrical noise and cable routing,

electrically shielded cabling may be required to preserve

resolution. If so, choose a housing with an integral connector and

select a shielded cordset, or contact Balluff for special shielded

cable versions of pre-wired sensors.

1.98

80×80×40

non flush

0...10 V

0...50 mm (adj.)

BAW MKK-050_19-S4

24 V DC

19…29 V DC

3.60 V DC @ 24 V DC

12.0 mA

50.0 mm

25.0 ± 1.0 mm

0.01 V per 0.05 mm

± 1.0 mm

0.0125 mm/°K

-10…+70 °C

75 Hz

1.0 s

10 k

250 V AC

IP 67

polymeric PBT

M12 DC Micro

yes

M18×1

non flush

0...10 V

2...8 mm

BAW M18MG-UAC80F-S04G

24 V DC

15…30 V DC

3.60 V DC @ 24 V DC

10.0 mA

6.00 mm

5.00 ± 0.5 mm

0.01 V per 0.006 mm

± 0.18 mm

0.0015 mm/°K

-10…+70 °C

500 Hz

1.0 ms

2 k

75 V DC

IP 67

nickel plated brass

PBTP

M12 DC Micro

yes

Analog Sensors

M8, M12, M18, M30

PG 36, 80×80×40

Inductive

Sensors

M30x1.5

flush

0...10 V

2...10 mm

BAW M30ME-UAC10B-S04G

24 V DC

15…30 V DC

3.60 V DC @ 24 V DC

10.0 mA

8.00 mm

6.00 ± 0.6 mm

0.01 V per 0.008 mm

± 0.24 mm

0.002 mm/°K

-10…+70 °C

500 Hz

1.0 ms

2 k

75 V DC

IP 67

nickel plated brass

PBTP

M12 DC Micro

yes

PG 36

flush

0...10 V

0...20 mm (adj.)

BAW MKZ-471_19-S4

24 V DC

19…29 V DC

3.60 V DC @ 24 V DC

12.0 mA

20.0 mm

10.0 ± 0.1 mm

0.01 V per 0.02 mm

± 0.2 mm

0.005 mm/°K

-10…+70 °C

75 Hz

1.0 s

10 k

250 V AC

IP 67

nickel plated brass

polymeric PBT

M12 DC Micro

yes

M30x1.5

44.5

LED

M12x1

P0326

Approvals

IEC 60947-5-2

UL 508

CSA C22.2 No. 14-M91

NEMA ICS 5-1996

1.99

Inductive

Sensors Analog Sensors

Set Point Output

Technical Description

For the ultimate in flexibility, Balluff

offers an ULTRALINEARTM analog

sensor with three independently

programmable, discrete setpoint

outputs, along with an analog voltage

output for reference. By holding a metal

target in position and momentarily

connecting the control line to the

supply, the output is preset to change

states whenever it reaches the

programmed analog signal level.

Setpoint programming can be

accomplished using your PLC or with

an available hand-held programmer

(order separately BES-516-4).

Features

All the exceptional features from our

standard ULTRALINEARTM family plus...

Remotely programmable setpoints

Process can be reconfigured on the

fly by altering controller's

programmed response

No need to physically adjust sensor

position for a particular setpoint

Status LED for each setpoint output

0016A001

Control Input

Analog Output

Digital Output 1

Digital Output 2

Digital Output 3

Analog

Output

Measurement

Range

10V

1.0 mm 5.0 mm

Output 1 OffOutput 1 On

Analog Output

Output 2 OffOutput 2 On

Output 3 OffOutput 3 On

Programmable

Digital Outputs

Set point 1

Set point 2

Set point 3

0016A003

Output Signals

Wiring Diagram

Housing size

Mounting

Output signal

Linear range sl

Ordering code

Voltage 0…10 V

Rated operational voltage Ue

Supply voltage UB

Ripple

Linear span sL 1

Midpoint of linear range se 2

Resolution 3

Repeatability 5

Non-linearity, max. 4

Temperature drift, max. 6 (+15…55 °C)

Ambient temperature range Ta

Cutoff frequency (-3 dB analog output amplitude)

Maximum switching frequency, discrete outputs

Load resistance RL

No-load supply current I0 @ Ue

Ambient temperature range Ta

Current rating Ie per setpoint output

Switchpoint hysteresis

Switchpoint repeatability

Rated insulation voltage Ui

Degree of protection per IEC 529

Housing material

Sensing face material

Connection

LED display for each setpoint output - active ON

Short circuit/overload protected

Protected against polarity reversal

M18×1

flush

0...10 V

1...5 mm

BAW M18MI2-UAC50B-BP05-002

24 V DC

15…30 V DC

3.6V DC

4.00 mm

3.00 mm ± 0.3 mm

0.01 V per 0.004 mm

± 0.12 mm

0.001 mm/°K

-10…+70 °C

500 Hz

1000 Hz

2 k

20.0 mA

-10…+70 °C

20.0 mA

0.3 mm

0.1 mm

75 V DC

IP 67

nickel plated brass

PBTP

5 m unshielded PUR cable (7 x 24 AWG)

yes

Cable Out

Optional BES-516-4 hand-

held programming unit

1.100

Inductive

Sensors

Position feedback using

ramped target.

Measuring deflection of a

saw blade.

The saw blade position is

detected by the sensor and

the blade guide mechanism

accordingly adjusted.

Detecting large linear motion

on machines using econo-

mical analog sensors.

Detecting a defined center

position of a sliding, rotating

machine part.

A controller processes both

sensor signals.

Nuts are checked for correct

orientation (automated

assembly).

Measuring the deflection of a

spring steel band to maintain

pressure on sheet material.

Sorting metal objects. Paper thickness

measurement using

leverage. This arrangement

can be used to distinguish

between 1 or 2 sheets.

Applications include

document readers, mass

printers, etc. Resolution

varies with leverage.

Eccentricity sensing or

angle positioning.

distance measurement

thickness measurement using opposed sensors

thickness measurement using leverage

concentricity measurement

circularity measurement

wobble measurement

deflection measurement

wear measurement

Applications

metal homogenity measurement

sorting metal objects by size, shape, material

metal object orientation sensing

absolute linear position feedback using direct metal

target approach

absolute linear travel feedback using angled metal

surface to increase effective range

absolute rotary position feedback using eccentric

metal cam

Analog Sensors

Applications