TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES * Improved immunity against HF and RF noise * Low supply current * Photo detector and preamplifier in one package * Internal filter for PCM frequency * Supply voltage: 2.5 V to 5.5 V * Improved immunity against optical noise * Insensitive to supply voltage ripple and rnoise 1 2 3 * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 16672 DESIGN SUPPORT TOOLS click logo to get started DESCRIPTION Models The TSOP22.., TSOP48.., TSOP24.. and TSOP44.. series are miniaturized IR receiver modules for infrared remote control systems. A PIN diode and a preamplifier are assembled on lead frame, the epoxy package contains an IR filter. Available MECHANICAL DATA Pinning for TSOP44.., TSOP48..: 1 = OUT, 2 = GND, 3 = VS The demodulated output signal can be directly connected to a microprocessor for decoding. Pinning for TSOP22.., TSOP24..: 1 = OUT, 2 = VS, 3 = GND The TSOP24.., TSOP44.. series devices are optimized to suppress almost all spurious pulses from Wi-Fi and CFL sources. They may suppress some data signals if continuously transmitted. The TSOP22.., TSOP48.. series devices are provided primarily for compatibility with old AGC2 designs. New designs should prefer the TSOP24.., TSOP44.. series containing the newer AGC4. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY, FOR LONG BURST REMOTE CONTROLS (AGC2) AGC Carrier frequency RECOMMENDED FOR LONG BURST CODES (AGC4) 30 kHz TSOP4830 TSOP2230 TSOP4430 33 kHz TSOP4833 TSOP2233 TSOP4433 TSOP2430 TSOP2433 36 kHz TSOP4836 TSOP2236 TSOP4436 (1)(2)(3) TSOP2436 (1)(2)(3) 38 kHz TSOP4838 TSOP2238 TSOP4438 (4)(5)(6) TSOP2438 (4)(5)(6) 40 kHz TSOP4840 TSOP2240 TSOP4440 TSOP2440 56 kHz TSOP4856 TSOP2256 TSOP4456 (6)(7) TSOP2456 (6)(7) Package Mold Pinning 1 = OUT, 2 = GND, 3 = VS 1 = OUT, 2 = VS, 3 = GND 1 = OUT, 2 = GND, 3 = VS 1 = OUT, 2 = VS, 3 = GND Dimensions (mm) 6.0 W x 6.95 H x 5.6 D Mounting Leaded Application Best choice for Rev. 1.8, 26-Sep-2018 Remote control (1) RC-5 (2) RC-6 (3) Panasonic 1 (4) NEC (5) Sharp (6) r-step (7) Thomson RCA Document Number: 82459 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 16833_14 17170-11 Transmitter with TSALxxxx 33 k R1 IR receiver VS 1 Input Band pass AGC Demodulator + VS C1 Circuit 3 C OUT VO GND GND 2 PIN Control circuit R1 and C1 recommended to reduce supply ripple for VS < 2.8 V ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL VALUE Supply voltage TEST CONDITION VS -0.3 to +6 V Supply current IS 5 mA Output voltage VO -0.3 to 5.5 V VS - VO -0.3 to (VS + 0.3) V IO 5 mA Voltage at output to supply Output current Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature UNIT Tj 100 C Tstg -25 to +85 C Tamb -25 to +85 C Tamb 85 C Ptot 10 mW t 10 s, 1 mm from case Tsd 260 C Note * Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. Ev = 0, VS = 5 V ISD 0.55 0.7 0.9 mA Ev = 40 klx, sunlight ISH - 0.8 - mA VS 2.5 - 5.5 V Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA d - 24 - m Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 VOSL - - 100 mV Minimum irradiance Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 Ee min. - 0.12 0.25 mW/m2 Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 Ee max. 50 - - W/m2 Directivity Angle of half transmission distance 1/2 - 45 - deg Supply current Supply voltage Transmission distance Rev. 1.8, 26-Sep-2018 2 UNIT Document Number: 82459 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms) t tpi * T 10/f0 is recommended for optimal function * tpi Output Signal VO 1) VOH VOL 2) 0.8 ton, toff - Output Pulse Width (ms) Ee 16110 7/f0 < td < 15/f0 tpi - 5/f0 < tpo < tpi + 6/f0 ton 0.7 0.6 0.5 toff 0.4 0.3 0.2 = 950 nm, optical test signal, fig. 1 0.1 0 0.1 tpo 2) td 1) Fig. 1 - Output Active Low Ee min./Ee - Relative Responsivity tpo - Output Pulse Width (ms) 100 1000 10 000 1.2 Output pulse width 0.9 0.8 Input burst length 0.7 0.6 0.5 0.4 0.3 0.2 = 950 nm, optical test signal, fig. 1 0.1 1.0 0.8 0.6 0.4 f = f0 5 % f(3 dB) = f0/10 0.2 0.0 0 0.1 10 1000 0.7 100 000 Ee - Irradiance (mW/m2) Ee min. - Threshold Irradiance (mW/m2) t 600 s t = 60 ms 94 8134 Output Signal, (see Fig. 4) VOH VOL t on t off t 1.3 5.0 4.5 4.0 3.5 3.0 2.5 2.0 Correlation with ambient light sources: 10 W/m2 = 1.4 klx (std. ilum. A, T = 2855 K) 10 W/m2 = 8.2 klx (daylight, T = 5900 K) Wavelength of ambient illumination: = 950 nm 1.5 1.0 0.5 0 0.01 0.1 1 10 100 Ee - Ambient DC Irradiance (W/m2) Fig. 3 - Output Function Rev. 1.8, 26-Sep-2018 1.1 Fig. 5 - Frequency Dependence of Responsivity Optical Test Signal 600 s 0.9 f/f0 - Relative Frequency 16925 Fig. 2 - Pulse Length and Sensitivity in Dark Ambient VO 10 Fig. 4 - Output Pulse Diagram 1.0 Ee 1 Ee - Irradiance (mW/m2) t Fig. 6 - Sensitivity in Bright Ambient 3 Document Number: 82459 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors 1.0 0.9 0.9 2nd line S()rel. - Relative Spectral Sensitivity 0.8 0.7 f = f0 f = 10 kHz f = 100 kHz 0.6 0.5 0.4 0.3 0.2 0.1 0 1 10 100 10000 0.8 0.7 1000 0.6 1st line 2nd line Ee min. - Threshold Irradiance (mW/m2) Axis Title 1.0 0.5 0.4 100 0.3 0.2 0.1 1000 0 750 VS RMS - AC Voltage on DC Supply Voltage (mV) 850 1050 10 1150 - Wavelength (nm) 21425 Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 950 Fig. 10 - Relative Spectral Sensitivity vs. Wavelength 0 0.8 10 20 30 Max. Envelope Duty Cycle 0.7 0.6 40 0.5 1.0 TSOP22.. TSOP48.. 0.4 0.3 50 0.8 60 TSOP24.. TSOP44.. 0.2 70 0.7 0.1 0 0.9 80 f = 38 kHz, Ee = 2 mW/m 0 21396_13 20 40 60 80 100 120 0.6 Burst Length (Number of Cycles/Burst) 96 12223p2 0.2 0 Fig. 11 - Horizontal Directivity 0.40 0.8 0.35 0.7 Ee min. - Sensitivity (mW/m2) Ee min. - Threshold Irradiance (mW/m2) Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length 0.4 drel - Relative Transmission Distance 0.30 0.25 0.20 0.15 0.10 0.05 0.6 0.5 0.4 0.3 0.2 0.1 0 0 -30 -10 10 30 50 70 2 90 3 4 5 6 Tamb - Ambient Temperature (C) VS - Supply Voltage (V) Fig. 9 - Sensitivity vs. Ambient Temperature Fig. 12 - Sensitivity vs. Supply Voltage Rev. 1.8, 26-Sep-2018 4 Document Number: 82459 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device's band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. 10000 7 When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver's output. Some examples which are suppressed are: 5 1000 1st line 2nd line 2nd line IR Signal Amplitude 6 4 3 100 2 1 10 0 * DC light (e.g. from tungsten bulbs sunlight) 0 * Continuous signals at any frequency 5 15 20 Time (ms) 16920 * Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 13 or Fig. 14). 10 Fig. 13 - IR Disturbance from Fluorescent Lamp With Low Modulation * 2.4 GHz and 5 GHz Wi-Fi Axis Title 10000 40 1000 0 1st line 2nd line 2nd line IR Signal Amplitude 20 -20 100 -40 10 -60 0 5 10 15 20 Time (ms) 16921 Fig. 14 - IR Disturbance from Fluorescent Lamp With High Modulation TSOP22.., TSOP48.. TSOP24.., TSOP44.. Minimum burst length 10 cycles/burst 10 cycles/burst After each burst of length a minimum gap time is required of 10 to 70 cycles 12 cycles 10 to 35 cycles 12 cycles 70 cycles > 4 x burst length 35 cycles > 10 x burst length For bursts greater than a minimum gap time in the data stream is needed of Maximum number of continuous short bursts/second 800 1300 NEC code Yes Preferred RC5/RC6 code Yes Preferred Thomson 56 kHz code Yes Preferred Sharp code Yes Preferred Mild disturbance patterns are suppressed (example: signal pattern of Fig. 13) Complex and critical disturbance patterns are suppressed (example: signal pattern of Fig. 14 or highly dimmed LCDs) Suppression of interference from fluorescent lamps Note * For data formats with short bursts please see the datasheet of TSOP23.., TSOP43.. Rev. 1.8, 26-Sep-2018 5 Document Number: 82459 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP22.., TSOP24.., TSOP48.., TSOP44.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 3.9 1 1 30.5 0.5 (5.55) 8.25 6.95 5.3 6 0.85 max. 0.89 0.5 max. 2.54 nom. 1.3 0.7 max. 4.1 2.54 nom. 5.6 marking area Not indicated tolerances 0.2 technical drawings according to DIN specifications R 2.5 Drawing-No.: 6.550-5169.01-4 Issue: 9; 03.11.10 13655 Rev. 1.8, 26-Sep-2018 6 Document Number: 82459 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000