Philips Semiconductors Product specification Triacs logic level BT136S series D BT136M series D GENERAL DESCRIPTION Glass passivated, sensitive gate triacs in a plastic envelope suitable for surface mounting, intended for use in general purpose bidirectional switching and phase control applications. These devices are intended to be interfaced directly to microcontrollers, logic integrated circuits and other low power gate trigger circuits. PINNING - SOT428 QUICK REFERENCE DATA SYMBOL VDRM IT(RMS) ITSM PARAMETER MAX. MAX. UNIT BT136S (or BT136M)Repetitive peak off-state voltages RMS on-state current Non-repetitive peak on-state current PIN CONFIGURATION PIN Standard Alternative NUMBER S M 1 MT1 gate 2 MT2 MT2 3 gate MT1 tab MT2 MT2 500D 500 4 25 600D 600 4 25 V A A SYMBOL tab T2 T1 2 1 G 3 LIMITING VALUES Limiting values in accordance with the Absolute Maximum System (IEC 134). SYMBOL PARAMETER VDRM Repetitive peak off-state voltages IT(RMS) ITSM RMS on-state current Non-repetitive peak on-state current I2t dIT/dt IGM VGM PGM PG(AV) Tstg Tj I2t for fusing Repetitive rate of rise of on-state current after triggering Peak gate current Peak gate voltage Peak gate power Average gate power Storage temperature Operating junction temperature CONDITIONS MIN. - full sine wave; Tmb 107 C full sine wave; Tj = 25 C prior to surge t = 20 ms t = 16.7 ms t = 10 ms ITM = 6 A; IG = 0.2 A; dIG/dt = 0.2 A/s T2+ G+ T2+ GT2- GT2- G+ over any 20 ms period MAX. -500 5001 UNIT -600 6001 V - 4 A - 25 27 3.1 A A A2s -40 - 50 50 50 10 2 5 5 0.5 150 125 A/s A/s A/s A/s A V W W C C 1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may switch to the on-state. The rate of rise of current should not exceed 3 A/s. July 1997 1 Rev 1.000 Philips Semiconductors Product specification Triacs logic level BT136S series D BT136M series D THERMAL RESISTANCES SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Rth j-mb Thermal resistance full cycle junction to mounting base half cycle Thermal resistance pcb (FR4) mounted; footprint as in Fig.14 junction to ambient - 75 3.0 3.7 - K/W K/W K/W MIN. TYP. MAX. UNIT T2+ G+ T2+ GT2- GT2- G+ - 2.0 2.5 2.5 5.0 5 5 5 10 mA mA mA mA T2+ G+ T2+ GT2- GT2- G+ VD = 12 V; IGT = 0.1 A IT = 5 A VD = 12 V; IT = 0.1 A VD = 400 V; IT = 0.1 A; Tj = 125 C VD = VDRM(max); Tj = 125 C 0.25 - 1.6 4.5 1.2 2.2 1.2 1.4 0.7 0.4 0.1 10 15 10 15 10 1.70 1.5 0.5 mA mA mA mA mA V V V mA MIN. TYP. MAX. UNIT - 5 - V/s - 2 - s Rth j-a STATIC CHARACTERISTICS Tj = 25 C unless otherwise stated SYMBOL PARAMETER CONDITIONS IGT Gate trigger current VD = 12 V; IT = 0.1 A IL Latching current IH VT VGT Holding current On-state voltage Gate trigger voltage ID Off-state leakage current VD = 12 V; IGT = 0.1 A DYNAMIC CHARACTERISTICS Tj = 25 C unless otherwise stated SYMBOL PARAMETER CONDITIONS dVD/dt Critical rate of rise of off-state voltage Gate controlled turn-on time VDM = 67% VDRM(max); Tj = 125 C; exponential waveform; RGK = 1 k ITM = 6 A; VD = VDRM(max); IG = 0.1 A; dIG/dt = 5 A/s tgt July 1997 2 Rev 1.000 Philips Semiconductors Product specification Triacs logic level 8 BT136S series D BT136M series D BT136 Ptot / W Tmb(max) / C 5 101 IT(RMS) / A BT136 104 7 6 = 180 1 107 C 4 107 120 5 110 90 60 4 3 113 30 3 116 2 119 1 122 2 1 0 0 1 2 3 IT(RMS) / A 125 5 4 0 -50 Fig.1. Maximum on-state dissipation, Ptot, versus rms on-state current, IT(RMS), where = conduction angle. 1000 50 Tmb / C 100 150 Fig.4. Maximum permissible rms current IT(RMS) , versus mounting base temperature Tmb. BT136 ITSM / A 0 12 BT136 IT(RMS) / A ITSM IT 10 T time 8 Tj initial = 25 C max 100 6 dIT /dt limit 4 T2- G+ quadrant 2 10 10us 100us 1ms T/s 10ms 0 0.01 100ms Fig.2. Maximum permissible non-repetitive peak on-state current ITSM, versus pulse width tp, for sinusoidal currents, tp 20ms. 30 ITSM / A BT136 T Tj initial = 25 C max 1.2 1 10 0.8 5 0.6 1 10 100 Number of cycles at 50Hz 0.4 -50 1000 Fig.3. Maximum permissible non-repetitive peak on-state current ITSM, versus number of cycles, for sinusoidal currents, f = 50 Hz. July 1997 BT136 1.4 time 15 0 VGT(Tj) VGT(25 C) I TSM IT 20 10 Fig.5. Maximum permissible repetitive rms on-state current IT(RMS), versus surge duration, for sinusoidal currents, f = 50 Hz; Tmb 107C. 1.6 25 0.1 1 surge duration / s 0 50 Tj / C 100 150 Fig.6. Normalised gate trigger voltage VGT(Tj)/ VGT(25C), versus junction temperature Tj. 3 Rev 1.000 Philips Semiconductors Product specification Triacs logic level 3 BT136S series D BT136M series D IGT(Tj) IGT(25 C) Tj = 125 C Tj = 25 C T2+ G+ T2+ GT2- GT2- G+ 2.5 typ 10 max Vo = 1.27 V Rs = 0.091 ohms 8 2 6 1.5 4 1 2 0.5 0 -50 0 50 Tj / C 100 0 150 Fig.7. Normalised gate trigger current IGT(Tj)/ IGT(25C), versus junction temperature Tj. 3 BT136 IT / A 12 BT136D IL(Tj) IL(25 C) 0 0.5 1 1.5 VT / V 2 2.5 3 Fig.10. Typical and maximum on-state characteristic. 10 TRIAC BT136 Zth j-mb (K/W) unidirectional 2.5 bidirectional 1 2 1.5 0.1 1 P D tp 0.5 t 0 -50 0 50 Tj / C 100 0.01 10us 150 IH(Tj) IH(25C) 1ms 10ms 0.1s 1s 10s tp / s Fig.11. Transient thermal impedance Zth j-mb, versus pulse width tp. Fig.8. Normalised latching current IL(Tj)/ IL(25C), versus junction temperature Tj. 3 0.1ms 1000 TRIAC dVD/dt (V/us) 2.5 100 2 1.5 10 1 0.5 0 -50 0 50 Tj / C 100 1 150 50 100 150 Tj / C Fig.12. Typical, critical rate of rise of off-state voltage, dVD/dt versus junction temperature Tj. Fig.9. Normalised holding current IH(Tj)/ IH(25C), versus junction temperature Tj. July 1997 0 4 Rev 1.000 Philips Semiconductors Product specification Triacs logic level BT136S series D BT136M series D MECHANICAL DATA Dimensions in mm seating plane Net Mass: 1.1 g 6.73 max 1.1 tab 2.38 max 0.93 max 5.4 4 min 6.22 max 10.4 max 4.6 2 1 0.5 0.5 min 3 0.3 0.5 0.8 max (x2) 2.285 (x2) Fig.13. SOT428 : centre pin connected to tab. MOUNTING INSTRUCTIONS Dimensions in mm 7.0 7.0 2.15 1.5 2.5 4.57 Fig.14. SOT428 : minimum pad sizes for surface mounting. Notes 1. Plastic meets UL94 V0 at 1/8". July 1997 5 Rev 1.000 Philips Semiconductors Product specification Triacs logic level BT136S series D BT136M series D DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. Philips Electronics N.V. 1997 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. July 1997 6 Rev 1.000 Philips Semiconductors: Product information o... Go to Philips Catalog & Datasheets Catalog by Function -Discrete semiconductors -Audio -Clocks and Watches -Data communications -Microcontrollers -Peripherals -Standard analog -Video -Wired communications -Wireless communications Catalog by System -Automotive -Consumer Multimedia Systems -Communications -PC/PC-peripherals Cross reference Models Packages Application notes Selection guides Other technical documentation End of Life information Datahandbook system Relevant Links -About catalog tree -About search -About this site -Subscribe to eNews -Catalog & Datasheets -Search BT136S series - Products D; BT136M series D BT136S series - Download D; BT136M series D Page 1 of 2 Select & Go... Information a Product INFOrmation page BT136S series D; BT136M series D; Triacs logic level * Description * Datasheet * Products, packages, availability and ordering * Find similar products To be kept informed on BT136S series D; B Description Glass passivated, sensitive gate triacs in a plastic envelope suitable for surface intended for use in general purpose bidirectional switching and phase control ap These devices are intended to be interfaced directly to microcontrollers circuits and other low power gate trigger circuits. Datasheet Type nr. Title BT136S Triacs logic level series D; BT136M series D Publication release Datasheet date status 01-Jul-97 Product Specification Page count 6 Products, packages, availability and ordering Partnumber North American Partnumber Order code (12nc) marking/packingpackage Standard BT136S-600D Marking * Reel BT136S-600D 9340 492 90118 SOT428 T/R Pack, SMD, 13" Please read information about some discontinued variants of this product Find similar products: BT136S series D; BT136M series D links to the similar products page conta Products file:\\Roarer\root\data13\imaging\BITTING\cpl_mismatch\20000817\08162000_3\PHGL\08112000 8/18/00 Philips Semiconductors: Product information o... Page 2 of 2 overview of products that are similar in function or related to the part number(s) this page. The similar products page includes products from the same catalog tr relevant selection guides and products from the same functional category. Copyright (c) 2000 Royal Philips Electronics All rights reserved. Terms and conditions. file:\\Roarer\root\data13\imaging\BITTING\cpl_mismatch\20000817\08162000_3\PHGL\08112000 8/18/00