RF LOW NOISE BLOCKDOWN CONVERTER Europe: LNB for Broadcasting Satellite Features (1) (2) (3) (4) Wide band type receiving all broadcasting channels (analog & digital) of Europe. [Universal LNB] Originally developed feed-horn waveguide makes the wide-band, low-noise characteristics possible. One of the industry's most compact and lightweight package Low consumption current design for energy saving [80 mA (TYP.): BS1R8EL100A] Specifications NF (dB) Conversion gain (dB) Phase noise Cross-polar discrimination (dB) Vertical polarization Supply voltage (V DC) (Polarization switching voltage) Horizontal polarization Power consumption (mA) Waveguide Output impedance () Output connector (F-type) Outline dimensions (mm) Weight (g) BS1R6EL400A Europe, Astra/Eutelsat Satellite etc. Horizontal/Vertical polarization BS1R6EL400A <4 output> BS1R5EL200A <2 output> BS1R8EL100A <1 output> 10.7 to 11.7 [Low band], 11.7 to 12.75 [High band] 950 to 1 950 [Low band], 1 100 to 2 150 [High band] 9.75 [Low band], 10.6 [High band] 1.3 (TYP.) [Low band], 0.7 (TYP.) 0.8 (TYP.) 1.1 (TYP.) [High band] 46 (MIN.) -50 dBc/Hz @1 kHz (MAX.) -55 dBc/Hz @1 kHz (TYP.) 25 (TYP.)/20 (MIN.) 11.5 to 14.0 (0/22 kHz) 16.0 to 19.0 (0/22 kHz) 290 (MAX.) 190 (TYP.)/250 (MAX.) 80 (TYP.)/120 (MAX.) Feed-horn (F/D = 0.6) 75 4-output 2-output 1-output (H/V, High and low switching) (H/V, High and low switching) (H/V, High and low switching) 63.4 x 138.2 x 152.4 61.5 x 135.6 x 129.5 107.3 x 60.0 x 60.0 Approx. 460 Approx. 430 Approx. 145 BS1R5EL200A BS1R8EL100A RF Components Destination Receiving polarization Model No. <Type> Input frequency (GHz) Output frequency (MHz) Local oscillation frequency (GHz) U.S.A.: LNB for FSS Broadcast/(Others: LNB for Communication) Specifications Receiving system Receiving polarization Model No. Input frequency (GHz) Output frequency (MHz) Local oscillation frequency (GHz) NF (dB) Conversion gain (dB) Phase noise Cross-polar discrimination (dB) Supply voltage (V DC) Power consumption (mA) Waveguide Output impedance () Output connector (F-type) Outline dimensions (mm) Weight (g) U.S.A.: FSS, Japan and others: for communication Horizontal/vertical polarization BS1C1UR100A 11.7 to 12.2 950 to 1 450 10.75 0.7 (TYP.)/0.9 (MAX.) 50 to 62 -60 dBc/Hz @1 kHz (TYP.) -- 12 to 24 120 (TYP.)/150 (MAX.) WR-75 75 1-output 48.6 x 96.3 x 45.5 Approx. 100 BS1C1UR100A Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 123 RF LOW NOISE BLOCKDOWN CONVERTER Japan/Asia/Australia: LNBs for CS Digital Satellite Broadcast Specifications Destination Receiving polarization Model No. <Type> Input frequency (GHz) Output frequency (MHz) Local oscillation frequency (GHz) NF (dB) Conversion gain (dB) Phase noise Cross-polar discrimination (dB) Vertical polarization Supply voltage (V DC) (Polarization switching voltage) Horizontal polarization Power consumption (mA) Waveguide Output impedance () Output connector (F-type) Outline dimensions (mm) Weight (g) Japan, Asia, Australia, CS Satellite Horizontal/Vertical polarization BS1R5AQ100A 12.25 to 12.75 950 to 1 450 11.3 0.6 (TYP.) / 1.0 (MAX.) 50 (MIN.) -75 dBc/Hz @1 kHz (TYP.) 25 (TYP.)/20 (MIN.) 11.5 to 14.0 16.0 to 19.0 80 (TYP.)120 (MAX.) Feed-horn (F/D = 0.6) 75 1-output (H/V switching) 140 x 60 x 60 Approx. 180 BS1R5AQ100A Japan: LNBs for BS/CS 110 Satellite Broadcast Features (1) Can receive 2 satellite broadcasts of 110 BS/CS digital [Employs wide-band (1 GHz) circular' linear polarization conversion technology (septum waveguide structure)] (2) Outstanding noise figure (NF) characteristics enabling compact design of antenna diameter. [NF: 0.45 dB (TYP.)/BS1F6JU300A] (3) Low current consumption design for improved energy saving. [80 mA (TYP.)] Standard Specifications Destination Receiving polarization Model No. Input frequency (GHz) Output frequency (MHz) Local oscillation frequency (GHz) NF (dB) Conversion gain (dB) Phase noise Cross-polar discrimination (dB) Right circular polarization Supply voltage (V DC) (Polarization switching voltage) Left circular polarization Power consumption (mA) Waveguide Output impedance () Output connector (F-type) Outline dimensions (mm) Weight (g) 124 Japan BS/CS 110 Satellite Right/Left circular polarization BS1F6JU300A BS1F6JP300A BS1F6JP100A 11.71023 to 12.751 1 032.23 to 2 073 10.678 0.45 (TYP.) / 0.7 (TYP.) / 1.1 (MAX.) 0.6 (MAX.) 48 to 60 -65 dBc/Hz @1 kHz (TYP.) 25 (TYP.)/20 (MIN.) 9.5 to 18.0 13.5 to 16.5 -- 9.5 to 12.0 80 (TYP.)/110 (MAX.) Feed-horn (F/D=0.5) 75 1-output 1-output (R/L switching) 96 x 53.07 x 71 Approx. 130 (not including outer cabinet) Right circular polarization BS1F6JP300A * Outer cabinet is made upon request. Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. DIGITAL DBS FRONT-END UNITS Digital DBS Front-End Units unit for digital broadcasting features high quality of signal transmission and improved elimination ability of various D BSkindsfront-end of rejection thanks to using Sharp's original ICs. Features (1) Equipped with a direct conversion IC developed by Sharp. Reliability is improved by reducing power consumption and component counts. (2) Compact and thin design enabling installation on a personal computer PCI card. [Thickness: 12.9 mm (MAX.)] (3) Wide-band reception design also covering CS broadcast band. [Reception frequency: 950 to 2 150 MHz] (4) Wide product line-up of LINK integrated types for contributing to set development time reduction. [Compatible with QPSK/8PSK demodulation] (5) User support tools can be provided. [Sample/evaluation boards and software are available.] Standard Specifications Destination Europe/U.S.A./Japan Input type 1-input 1-input, 1-loop through output 1-input Model No. BS2S7VZ0302A BS2S7HZ0302A BS2S7HZ6306 Input frequency (MHz) 950 to 2 150 Input signal level (dBm) -65 to -25 The 1st intermediate frequency (MHz) Zero-IF (Direct conversion) Base band frequency bandwidth 10 to 30, 2.0 MHz step (BB LPF) RF input local leak (dBm) PLL phase noise (dBc/Hz) -63 (MAX.) 10 kHz offset -75 (TYP.) 1 kHz offset -70 (TYP.) Output type Channel selection system Noise figure (dB) Tuning voltage (V DC) I/Q PLL (I2C-bus)*1 12 (MAX.) (Not required)*2 Supply voltage (V DC) LNB power supply 3.3 DC 25 V, 400 mA (MAX.) Input impedance () Outline dimensions (mm) BS2S7VZ0302A 75 29.6 x 37.9 x 11.0 30.6 x 25.0 x 11.7 BS2S7HZ6306 RF Components Contact SHARP for custom design product. *1 I2C-bus is a trademark of Philips Corporation. *2 Terminal supply voltage is not required. Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 125 RF DIGITAL DBS FRONT-END UNITS Digital DBS Front-End Units (QPSK Demodulator Circuit Built-in Type) Specifications <QPSK demodulator circuit built-in type> Destination Europe/U.S.A./Japan Input type Model No. 1-input, 1-loop through output (super compact type) 1-input, 1-loop through output BS2F7VZ0194A BS2F7VZ0724 Input frequency (MHz) BS2F7VZ7294 950 to 2 150 Input signal level (dB m) -65 to -25 The 1st intermediate frequency (MHz) Zero-IF (Direct conversion) Base band frequency bandwidth (MHz) 10 to 30, 2.0 MHz step (BB LPF) RF input local leak (dB m) -63 (MAX.) Output type 8-bit transport Symbol rate (M baud) 45 (MAX.) Eb/No = 5.5 dB (Max.) [PR = 3/4, BER = 2 x 10 -4] BER (Viterbi output) PLL (I2C-bus)*1 Channel selection system Noise figure (dB) 12 (MAX.) (Not required)*2 Tuning voltage (V DC) Supply voltage (V DC) 3.3, 2.5 LNB power supply 3.3, 1.8 3.3, 2.5 25 V DC, 400 mA (MAX.) Input impedance () 75 BS2F7VZ0194A 55.1 x 37.9 x 11.0 Outline dimensions (mm) 57.5 x 29.6 x 13.2 Contact SHARP for custom design product. *1 I2C-bus is a trademark of Philips Corporation. *2 Terminal supply voltage is not required. Digital DBS Front-End Units (8 PSK Demodulator Circuit Built-in Type) Specifications <8 PSK demodulator circuit built-in type> Destination Japan Input type/Features 1-input, 1-loop through output 1-input Model No. BS2F7HZ6460 Input frequency (MHz) BS2F7VZ0460 950 to 2 150 Input signal level (dB m) -65 to -25 The 1st intermediate frequency (MHz) Zero-IF (Direct conversion) 22 (BB LPF) variable type Base band frequency bandwidth (MHz) RF input local leak (dB m) 22.5 (BB LPF) variable type -63 (MAX.) Parallel/serial transport output Symbol rate (M baud) 28.86 PLL (I2C-bus)*1 Channel selection system Noise figure (dB) 8 (TYP.) (Not required)*2 Tuning voltage (V DC) Supply voltage (V DC) 3.3, 1.5 LNB power supply 25 V DC, 400 mA (MAX.) Input impedance () Outline dimensions (mm) BS2F7HZ6460 Serial transport output Output type 75 65.8 x 26.0 x 13.7 (MAX.) BS2F7VZ0460 55.1 x 37.9 x 11.0 *1 I2C-bus is a trademark of Philips Corporation. *2 Terminal supply voltage is not required. 126 Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. COMBINATION FRONT-END FOR DIGITAL TERRESTRIAL AND DIGITAL SATELLITE BROADCASTING Combination Front-End for Digital Terrestrial and Digital Satellite Broadcasting Features (1) Enables simultaneous reception of digital terrestrial and digital satellite broadcasting. (2) Contributes to making LCD TVs, etc. thinner. (3) Combination reception module for terrestrial digital: A tuner circuit, a demodulator, an MPEG decoder and a video encoder combined in a single module. Standard Specifications Destination Japan Model No. VA1W1JF9003 RF circuit system Input frequency (MHz)* 1 Input signal level*2 (dBm) Output type Digital terrestrial Digital DBS Single conversion type Direct conversion type VHF, UHF, CATV VHF Low: 93 to 159 VHF High: 167 to 351 UHF: 357 to 767 950 to 2 150 -75 to -20 -65 to -25 Direct IF [Balance] (Output frequency: 57MHz) I/Q IF bandwidth (MHz) 6 - Base band frequency bandwidth - 10 MHz to 30 MHz, 2.0 MHz step (BB LPF) Noise figure (dB) PLL phase noise (dBc/Hz) Image rejection (dB) 6 (TYP.) 6 (TYP.) -90 (TYP.) at 10kHz offset -80 (TYP.) at 10kHz offset 65 (TYP.) Power consumption (W) Supply voltage (V DC) Outline dimensions (mm) VA1W1JF9003 1.57 (TYP.) (When the digital terrestrial and digital satellite broadcasting are received simultaneously) 5 3.3*4 60.9 x 42.1 x 12.6 An RF front-end unit is additionally required to receive analog broadcasting. It conforms to the ARIB standard. I2C-bus is a trademark of Philips Corporation. DC 5V type of supply voltage is also available. RF Components *1 *2 *3 *4 - PLL (I2C-bus)*3 Channel selection system Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 127 RF DIGITAL TERRESTRIAL FRONT-END UNIT Front-End Units for ISDB-T/DVB-T Features (1) (2) (3) (4) Low phase noise characteristics, high elimination of adjacent channel interference. Transport stream output front-end units with built-in OFDM demodulation IC. [VA1L5JF6013/VA1J5ED5055] Compact, low power consumption. Other types are available with various forms of chassis (vertical or horizontal type) and input connectors (F or DIN type), etc. Standard Specifications Destination Japan Product name Model No. Input frequency (MHz)* 1 Output ISDB-T front end (IF output) VA1T1JF2091 VA1L5JF6023 Mode VA1K5ED5255 VHF: 143.5 to 430 UHF: 430 to 862 VHF: 143.5 to 430 UHF: 430 to 862 Direct IF Transport stream (Built-in OFDM demodulation) 7, 8, selectable 2k, 8k, both compatible -79 dBm (TYP.) [in mode 3, 64 QAM, CR = 7/8 (QEF)] -81 dBm (TYP.) [at 2 k, 64 QAM, CR = 2/3 (QEF)] -- 6 (TYP.) -90 dBc/Hz (TYP.) [at 10 kHz offset] -90 dBc/Hz (TYP.) [at 10 kHz offset] 65 (TYP.) -- -- 22.3 dB (TYP.) [at input level: -45 dBm, in mode 3, 64 QAM, CR = 7/8 (QEF)] 55 (TYP.) -- -- 17.2 dB (TYP.) [at input level: -50 dBm, 64 QAM, CR = 2/3 (QEF)] PLL (I2C-bus)*2 Channel selection/control system Power consumption (W) 1.15 1.6 Supply voltage (V DC) 5, 30 1.5, 3.3, 5, 30 52.0 x 35.9 x 13.4 80.0 x 35.9 x 13.4 Outline dimensions (mm) VA1H1ED5265 6 -- Phase noise C/N VA1T1ED5065 Mode 1, 2, 3 Noise figure (dB) Image rejection (dB) DVB-T front end (built-in OFDM demodulation) DVB-T front end (IF output) VHF, UHF, CATV VHF Low: 93 to 159 VHF High: 167 to 351 UHF: 357 to 767 Transport stream Direct IF (Built-in OFDM demodulation) IF bandwidth (MHz) Input sensitivity Europe/Asia ISDB-T front end (built-in OFDM demodulation) 0.75 0.85 1.33 5, 3.3, 1.8 (DC-DC converter) 5 (DC-DC converter) 52.0 x 35.9 x 13.4 47.7 x 29.6 x 13.2 70.0 x 29.6 x 13.2 *1 An RF front-end unit is additionally required to receive analog broadcasting. *2 I2C-bus is a trademark of Philips Corporation. VA1T1JF2091 128 VA1L5JF6023 VA1S1ED5056 (VA1S8ED5056) VA1K5ED5255 Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. TWO-IN-ONE RF UNIT Under development Two-In-One RF Units (RF Front-End Unit + PIF Unit) Features (1) High performance RF front-end unit and PIF unit are integrated in one unit, resulting in a short developing time. (2) A composite unit structure improves operability during mounting. (3) Horizontal shaped models for LCD TVs/LCD monitors are available. (Vertical shaped models are also available.) Specifications TV system Japan U.S.A. VT2A5JW250 Model No. VHF Air CATV VHF Air C13 to C53 to 1 to 12 13 to 62 C52 C63 BL: 1 to 3, C13 to C22 BH: 4 to 12, C23 to C52 BU: 13 to 62, C53 to C63 Band split Intermediate frequency (MHz) Air CATV Air A-5 to W+12 to 2 to 13 14 to 69 W+11 W+84 BL: 2 to 6, A-5 to B BH: 7 to 13, C to W+11 BU: 14 to 69, W+12 to W+84 Air UHF CATV CATV Air 1A, Z1 to Z34 to 1 to 12 13 to 57 Z33 Z38 BL: 1 to 5, 1A, Z1 to Z4 BH: 6 to 12, Z5 to Z33 BU: 13 to 57, Z34 to Z38 58.75 45.75 38.0 Audio 54.25 41.25 D/K: 31.5, I: 32.0, B/G: 32.5, M/N: 33.5 Pseudo synchronization detection system, split-carr ier audio receiving system Terminals Input/loop-through output: F-type junction Input: F-type junction --*2 Input impedance () B voltage (V DC) Noise figure (dB) Input: DIN type terminal 75 RF with loop through* 2 MB: 5/BT: 31.5 9.5 9.5 9.5 --*2 MB: 5/BT: 31 9.5 Type IF CATV VHF Video Detection system RF front-end VT2W5CD551 UHF 4 6 MB: 5/BT: 31 5 5 6 7 6 PLL (I2C-bus)*1 Channel selection system Image rejection (dB) VL: 85, VH: 75 75 VL: 75, A5 to I: 80, J to W+84: 60 IF rejection (dB) VL: 80, VH: 95 95 VL: 90, VH: 100 60 VL: 70, VH: 70 55 100 VL: 50 to 70, VH: 90 90 Video output level (Vp-p) 1.0 1.0 1.0 Video output S/N (dB) 47 48 44 Noise limit sensitivity (dB) at S/N = 30 dB 45 43 42 Audio output level (mVrms) -- 290 290 Audio output S/N (dB) -- 55 45 Audio frequency characteristics (at 70 kHz) -- -1 (at 80 kHz) -0 (at 10 kHz) SIF output Outline dimensions (mm) 6 CATV receiver front end RF Components Receiving channels (ch) VT2W5UF250 UHF CATV China Possible to SIF output 50.3 x 38.4 x 12.7 60.9 x 41.5 x 15.0 *1 I2C-bus is a trademark of Philips Corporation. *2 Compatible with RF loop through type. VT2A5JW250 VT2W5UF250 Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 129 RF ANALOG TERRESTRIAL RF FRONT-END UNIT RF Front-End Units <VT1Y Series> Features (1) Miniature size achieved using thin profile, low height design in industry standard RF front-end unit (terminal shape and terminal pin arrays) (2) Model lineup corresponding to domestic product standards of Europe, China, Japan and the United States. DIN-type junction input type With RF output terminal type Specifications (Major models of VT1Y series) Destination Europe Type Model No. VT1Y5ED211 VHF Receiving channel (ch) Band split Intermediate frequency (MHz) U.S.A. China With PLL, for frequency CS, for frequency synthesizer, F-type junction synthesizer input IF output*1: No equilibrium Air CATV CATV GB, hyper, for frequency synthesizer VT1Y5UF201 UHF Air VHF Air With PLL, for frequency With PLL, for frequency synsynthesizer thesizer, with RF output VT1Y5CD201 UHF CATV CATV Japan Air VHF Air VT1Y5JF201 UHF CATV CATV Air VHF Air VT1Y5JB201 UHF CATV CATV VHF Air Air CATV CATV Air W+12 X to S37 to 21 to A-5 to 14 to 1A, Z1 Z34 to 13 to C13 to C53 to 13 to C13 to C53 to 13 to 2 to 12 2 to 13 to 1 to 12 1 to 12 1 to 12 S36 S41 C57 W+11 69 to Z33 Z38 57 C52 C63 62 C52 C63 62 W+84 BL: 2 to 6, A-5 to B BL: 1 to 5, 1A, Z1 to Z4 BL: 1 to 3, C13 to C22 BL: 1 to 3, C13 to C22 BL: 2 to 4, X to S6 BH: 5 to 12, S7 to S36 BH: 6 to 12, Z5 to Z33 BH: 4 to 12, C23 to C52 BH: 4 to 12, C23 to C52 BH: 7 to 13, C to W+11 BU: 21 to C57, S37 to S41 BU: 14 to 69, W+12 to W+84 BU: 13 to 57, Z34 to Z38 BU: 13 to 62, C53 to C63 BU: 13 to 62, C53 to C63 Video 38.9 45.75 38.0 58.75 Audio 33.4 41.25 31.5 54.25 +B: 5/BT: 31 +B: 5/BT: 31.5 +B: 5/BT: 31 +B: 5/BT: 31.5 B voltage (V DC) Input impedance () VSWR UHF 75 2 2 2 1.5 1.5 1.5 2 2 2 1.5 1.5 1.5 - - - Noise figure (dB) 5 7 6 5 5 6 5 7 6 4 5 4.5 8 9 8.5 Power gain (dB) 40 38 40 39 39 37 40 38 40 40 37 40 36 33 36 Image rejection (dB) IF rejection (dB) VL: 70 VH: 65 VL: 70 VH: 90 60 90 Outline dimensions (mm) VL: 70 VH: 60 VL: 80 VH: 90 60 85 VL: 70 VH: 65 VL: 70 VH: 90 60 90 VL: 85 VH: 85 VL: 85 VH: 85 80 100 VL: 85 VH: 85 VL: 85 VH: 85 80 100 53.0 x 33.6 x 14.3 (Note) The figures in the table are typical values. *1 Available IF output equilibrium model 130 Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. ANALOG TERRESTRIAL RF FRONT-END UNIT Ultra Compact Front-End Units <VT2V Series> Features (1) Compact and thin design suitable for building into a portable unit with LCD monitor. (Circuit area of 11.4 cm3) (2) Contribute to simplifying developing process and saving space thanks to the built-in VIF/SIF circuit. Specifications Destination Japan/U.S.A. Model No. VT2V8UP5510 Receiving channel The 1st intermediate frequency (MHz) Video Audio Supply voltage (V DC) Power consumption (W) Input impedance () VHF UHF JPN: 1 to 12 USA: 2 to 13 JPN: 13 to 62 USA: 14 to 69 CATV 45.75 41.25 5 single (DC-DC converter) 0.8 (TYP.) 75 Video S/N (dB) 50 (TYP.) Audio S/N (dB) 53 (TYP.) Noise limit sensitivity (dB) 42 (TYP.) Video frequency characteristics -1.0 dB (TYP.) at 3.58 MHz Audio frequency characteristics -1.5 dB (TYP.) at 80 kHz VT2V8UP5510 49.9 x 28.0 x 7.7 RF Components Outline dimensions (mm) FM Radio JPN: C13 to C63 JPN: 76 to 90 MHz USA: A-5 to W+84 USA: 88 to 108 MHz Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 131