AXA003A0XZ - ABB - Datasheet.Live

GE

Data Sheet

July 24, 2020

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc – 14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

Features

▪ Compliant to RoHS Directive 2011/65/EU and

amended Directive (EU) 2015/863

▪ Compliant to REACH Directive (EC) No 1907/2006

▪ Delivers up to 3A output current

▪ High efficiency – 91% at 3.3V full load (VIN = 12.0V)

▪ Small size and low profile:

22.9 mm x 10.2 mm x 6.63 mm

(0.90 in x 0.4in x 0.261 in)

▪ Low output ripple and noise

▪ High Reliability:

Calculated MTBF = 10.8M hours at 25oC Full-load

▪ Constant switching frequency (300 kHz)

▪ Output voltage programmable from 0.75 Vdc to 5.5

Vdc via external resistor

▪ Line Regulation: 0.3% (typical)

▪ Load Regulation: 0.4% (typical)

▪ Temperature Regulation: 0.4 % (typical)

▪ Remote On/Off

▪ Output overcurrent protection (non-latching)

▪ Wide operating temperature range (-40°C to 85°C)

▪ ANSI/UL* 62368-1 and CAN/CSA† C22.2 No. 62368-1

Recognized, DIN VDE‡ 0868-1/A11:2017 (EN62368-

1:2014/A11:2017

▪ ISO** 9001 and ISO 14001 certified manufacturing

facilities

Applications

▪ Distributed power architectures

▪ Intermediate bus voltage applications

▪ Telecommunications equipment

▪ Servers and storage applications

▪ Networking equipment

▪ Enterprise Networks

▪ Latest generation IC’s (DSP, FPGA, ASIC) and

Microprocessor powered applications

Description

Austin MiniLynxTM 12V SIP (single-inline) power modules are non-isolated DC-DC converters that can deliver up to 3A of

output current with full load efficiency of 91% at 3.3V output. These modules provide precisely regulated output voltage

programmable via external resistor from 0.75Vdc to 5.5Vdc over a wide range of input voltage (VIN = 8.3 - 14V). Their open-

frame construction and small footprint enable designers to develop cost- and space-efficient solutions. In addition to

sequencing, standard features include remote On/Off, programmable output voltage and over current protection.

* UL is a registered trademark of Underwriters Laboratories, Inc.

† CSA is a registered trademark of Canadian Standards Association.

‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V.

** ISO is a registered trademark of the International Organization of Standards

RoHS Compliant

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 2

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings

only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations

sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability.

Parameter

Device

Symbol

Min

Max

Unit

Input Voltage

All

VIN

-0.3

15

Vdc

Continuous

Operating Ambient Temperature

All

TA

-40

85

°C

(see Thermal Considerations section)

Storage Temperature

All

Tstg

-55

125

°C

Electrical Specifications

Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions.

Parameter

Device

Symbol

Min

Typ

Max

Unit

Operating Input Voltage

Vo,set ≤ 3.63

VIN

8.3

12

14

Vdc

Vo,set > 3.63

VIN

8.3

12

13.2

Vdc

Maximum Input Current

All

IIN,max

2.2

Adc

(VIN= VIN, min to VIN, max, IO=IO, max VO,set = 3.3Vdc)

Input No Load Current

VO,set = 0.75Vdc

IIN,No load

45

mA

(VIN = VIN, nom Vdc, IO = 0, module enabled)

VO,set = 5.5Vdc

IIN,No load

150

mA

Input Stand-by Current

All

IIN,stand-by

1.2

mA

(VIN = VIN, nom, module disabled)

Inrush Transient

All

I2t

0.4

A2s

Input Reflected Ripple Current, peak-to-peak

(5Hz to 20MHz, 1μH source impedance; VIN, min to VIN,

max, IO= IOmax ; See Test configuration section)

All

30

mAp-p

Input Ripple Rejection (120Hz)

All

30

dB

CAUTION: This power module is not internally fused. An input line fuse must always be used.

This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of a

complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety

and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6 A

(see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input

current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information.

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 3

Electrical Specifications (continued)

Parameter

Device

Symbol

Min

Typ

Max

Unit

Output Voltage Set-point

All

VO, set

-2.5

VO, set

+2.5

% VO, set

(VIN=VIN, min, IO=IO, max, TA=25°C)

Output Voltage

All

VO, set

-3%

⎯

+4%

% VO, set

(Over all operating input voltage, resistive load,

and temperature conditions until end of life)

Adjustment Range

All

VO

0.7525

5.5

Vdc

Selected by an external resistor

Output Regulation

Line (VIN=VIN, min to VIN, max)

All

⎯

0.3

⎯

% VO, set

Load (IO=IO, min to IO, max)

All

⎯

0.4

⎯

% VO, set

Temperature (Tref=TA, min to TA, max)

All

⎯

0.4

⎯

% VO, set

Output Ripple and Noise on nominal output

(VIN=VIN, nom and IO=IO, min to IO, max

Cout = 1μF ceramic//10μFtantalum capacitors)

RMS (5Hz to 20MHz bandwidth)

All

⎯

10

15

mVrms

Peak-to-Peak (5Hz to 20MHz bandwidth)

All

⎯

30

50

mVpk-pk

External Capacitance

ESR ≥ 1 mΩ

All

CO, max

⎯

1000

μF

ESR ≥ 10 mΩ

All

CO, max

⎯

3000

μF

Output Current

All

Io

0

3

Adc

Output Current Limit Inception (Hiccup Mode )

All

IO, lim

⎯

200

⎯

% Io

(VO= 90% of VO, set)

Output Short-Circuit Current

All

IO, s/c

⎯

2

⎯

Adc

(VO≤250mV) ( Hiccup Mode )

Efficiency

VO,set = 1.2Vdc

η

81.5

%

VIN= VIN, nom, TA=25°C

VO, set = 1.5Vdc

η

84.0

%

IO=IO, max , VO= VO,set

VO,set = 1.8Vdc

η

86.0

%

VO,set = 2.5Vdc

η

89.0

%

VO,set = 3.3Vdc

η

91.0

%

VO,set = 5.0Vdc

η

93.0

%

Switching Frequency

All

fsw

⎯

300

⎯

kHz

Dynamic Load Response

(dIo/dt=2.5A/s; VIN = VIN, nom; TA=25°C)

All

Vpk

⎯

200

⎯

mV

Load Change from Io= 50% to 100% of Io,max;

1μF ceramic// 10 μF tantalum

Peak Deviation

Settling Time (Vo<10% peak deviation)

All

ts

⎯

25

⎯

s

(dIo/dt=2.5A/s; VIN = VIN, nom; TA=25°C)

All

Vpk

⎯

200

⎯

mV

Load Change from Io= 100% to 50%of Io,max:

1μF ceramic// 10 μF tantalum

Peak Deviation

Settling Time (Vo<10% peak deviation)

All

ts

⎯

25

⎯

s

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 4

Electrical Specifications (continued)

Parameter

Device

Symbol

Min

Typ

Max

Unit

Dynamic Load Response

(dIo/dt=2.5A/s; V VIN = VIN, nom; TA=25°C)

All

Vpk

⎯

75

⎯

mV

Load Change from Io= 50% to 100% of Io,max;

Co = 2x150 μF polymer capacitors

Peak Deviation

Settling Time (Vo<10% peak deviation)

All

ts

⎯

100

⎯

s

(dIo/dt=2.5A/s; VIN = VIN, nom; TA=25°C)

All

Vpk

⎯

75

⎯

mV

Load Change from Io= 100% to 50%of Io,max:

Co = 2x150 μF polymer capacitors

Peak Deviation

Settling Time (Vo<10% peak deviation)

All

ts

⎯

100

⎯

s

General Specifications

Parameter

Min

Typ

Max

Unit

Calculated MTBF (IO=IO, max, TA=25°C)

per Telecordia SR-332 Issue 1: Method 1 Case 3

10,865,819

Hours

Weight

⎯

2.8 (0.1)

⎯

g (oz.)

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 5

Feature Specifications

Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See

Feature Descriptions for additional information.

Parameter

Device

Symbol

Min

Typ

Max

Unit

On/Off Signal interface

Device code with Suffix “4” – Positive logic

(On/Off is open collector/drain logic input;

Signal referenced to GND - See feature description section)

Input High Voltage (Module ON)

All

VIH

―

VIN, max

V

Input High Current

All

IIH

―

10

μA

Input Low Voltage (Module OFF)

All

VIL

-0.2

―

0.3

V

Input Low Current

All

IIL

―

0.2

1

mA

Device Code with no suffix – Negative Logic

(On/OFF pin is open collector/drain logic input with

external pull-up resistor; signal referenced to GND)

Input High Voltage (Module OFF)

All

VIH

2.5

―

VIN,max

Vdc

Input High Current

All

IIH

0.2

1

mA

Input Low Voltage (Module ON)

All

VIL

-0.2

―

0.3

Vdc

Input low Current

All

IIL

―

10

μA

Turn-On Delay and Rise Times

(IO=IO, max , VIN = VIN, nom, TA = 25 oC, )

Case 1: On/Off input is set to Logic Low (Module

ON) and then input power is applied (delay from

instant at which VIN =VIN, min until Vo=10% of Vo,set)

All

Tdelay

―

3

―

msec

Case 2: Input power is applied for at least one second

and then the On/Off input is set to logic Low (delay from

instant at which Von/Off=0.3V until Vo=10% of Vo, set)

All

Tdelay

―

3

―

msec

Output voltage Rise time (time for Vo to rise from 10%

of Vo,set to 90% of Vo, set)

All

Trise

―

4

―

msec

Output voltage overshoot – Startup

―

1

% VO, set

IO= IO, max; VIN = VIN, min to VIN, max , TA = 25 oC

Overtemperature Protection

All

Tref

⎯

140

⎯

°C

(See Thermal Consideration section)

Input Undervoltage Lockout

Turn-on Threshold

All

7.9

V

Turn-off Threshold

All

7.8

V

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 6

Characteristic Curves

The following figures provide typical characteristics for the Austin MiniLynxTM 12 V SIP modules at 25ºC.

EFFICIENCY,  (%)

70

72

74

76

78

80

82

84

86

88

0 0.6 1.2 1.8 2.4 3

VIN =14.0V

VIN = 12.0V

VIN = 8.3V

EFFICIENCY,  (%)

74

76

78

80

82

84

86

88

90

92

0 0.6 1.2 1.8 2.4 3

VIN = 14.0V

VIN =12.0V

VIN = 8.3V

OUTPUT CURRENT, IO (A)

Figure 1. Converter Efficiency versus Output Current (Vout

= 1.2Vdc).

Figure 4. Converter Efficiency versus Output Current (Vout

= 2.5Vdc).

EFFICIENCY,  (%)

70

72

74

76

78

80

82

84

86

88

0 0.6 1.2 1.8 2.4 3

VIN = 14.0V

VIN = 12.0V

VIN = 8.3V

EFFICIENCY,  (%)

71

74

77

80

83

86

89

92

95

0 0.6 1.2 1.8 2.4 3

VIN = 14.0V

VIN = 12.0V

VIN = 8.3V

OUTPUT CURRENT, IO (A)

Figure 2. Converter Efficiency versus Output Current (Vout

= 1.5Vdc).

Figure 5. Converter Efficiency versus Output Current (Vout

= 3.3Vdc).

EFFICIENCY,  (%)

72

74

76

78

80

82

84

86

88

90

0 0.6 1.2 1.8 2.4 3

VIN = 14.0V

VIN = 12.0V

VIN = 8.3V

EFFICIENCY,  (%)

72

75

78

81

84

87

90

93

96

99

0 0.6 1.2 1.8 2.4 3

VIN =14.0V

VIN = 12.0V

VIN = 8.3V

OUTPUT CURRENT, IO (A)

Figure 3. Converter Efficiency versus Output Current (Vout

= 1.8Vdc).

Figure 6. Converter Efficiency versus Output Current (Vout

= 5.0Vdc).

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 7

Characteristic Curves (continued)

The following figures provide typical characteristics for the Austin MiniLynxTM 12V SIP modules at 25ºC.

INPUT CURRENT, IIN (A)

0

0.2

0.4

0.6

0.8

1

1.2

1.4

1.6

7 8 9 10 11 12 13 14

Io=1.5A

Io=0A

Io=3A

OUTPUT CURRENT, OUTPUT VOLTAGE

IO (A) (1A/div) VO (V) (200mV/div)

INPUT VOLTAGE, VIN (V)

TIME, t (5 s/div)

Figure 7. Input voltage vs. Input Current

(Vout =3.3Vdc).

Figure 10. Transient Response to Dynamic Load Change

from 50% to 100% of full load (Vo = 3.3Vdc).

OUTPUT VOLTAGE

VO (V) (10mV/div)

OUTPUT CURRENT, OUTPUT VOLTAGE

IO (A) (1A/div) VO (V) (200mV/div)

TIME, t (1s/div)

TIME, t (5 s/div)

Figure 8. Typical Output Ripple and Noise

(VIN = 12.0V dc, Vo = 0.75Vdc, Io=3A).

Figure 11. Transient Response to Dynamic Load Change

from 100% to 50% of full load (Vo = 3.3 Vdc).

OUTPUT VOLTAGE

VO (V) (10mV/div)

OUTPUT CURRENT, OUTPUT VOLTAGE

IO (A) (1A/div) VO (V) (50mV/div)

TIME, t (1s/div)

TIME, t (50s/div)

Figure 9. Typical Output Ripple and Noise

(VIN = 12.0V dc, Vo = 3.3Vdc, Io=3A).

Figure 12. Transient Response to Dynamic Load Change

from 50% to 100% of full load (Vo = 3.3 Vdc, Cext = 2x150

μF Polymer Capacitors).

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 8

Characteristic Curves (continued)

The following figures provide typical characteristics for the Austin MiniLynxTM 12 V SIP modules at 25ºC.

OUTPUT CURRENT, OUTPUTVOLTAGE

IO (A) (1A/div) VO (V) (50mV/div)

INPUT VOLTAGE OUTPUT VOLTAGE

VIN (V) (10V/div) VO (V) (1V/div)

TIME, t (50s/div)

TIME, t (1ms/div)

Figure 13. Transient Response to Dynamic Load Change

from 100% of 50% full load (Vo = 3.3Vdc, Cext = 2x150 μF

Polymer Capacitors).

Figure 16. Typical Start-Up with application of Vin

(VIN = 12.0Vdc, Vo = 3.3Vdc, Io = 3A).

ON/OFF VOLTAGE OUTPUT VOLTAGE

VOn/off(V) (10V/div) VO (V) (1V/div)

ON/OFF VOLTAGE OUTPUT VOLTAGE

VOn/off(V) (10V/div) VO (V) (0.5V/div)

TIME, t (1ms/div)

Figure 14. Typical Start-Up Using Remote On/Off

(VIN = 12.0Vdc, Vo = 3.3Vdc, Io = 3A).

Figure 17 Typical Start-Up Using Remote On/Off with

Prebias (VIN = 12.0Vdc, Vo = 1.8Vdc, Io = 1.0A, Vbias

=1.0Vdc).

ON/OFF VOLTAGE OUTPUT VOLTAGE

VOn/off(V) (10V/div) VO (V) (1V/div)

OUTPUT CURRENT,

IO (A) (5A/div)

TIME, t (1ms/div)

TIME, t (20ms/div)

Figure 15. Typical Start-Up Using Remote On/Off with Low-

ESR external capacitors (7x150uF Polymer)

(VIN = 12.0Vdc, Vo = 3.3Vdc, Io = 3A, Co = 1050F).

Figure 18. Output short circuit Current

(VIN = 12.0Vdc, Vo = 0.75Vdc).

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 9

Characteristic Curves (continued)

The following figures provide thermal derating curves for the Austin MiniLynxTM 12 V SIP modules.

OUTPUT CURRENT, Io (A)

0

0.5

1

1.5

2

2.5

3

3.5

20 30 40 50 60 70 80 90

0 LFM

100 LFM

OUTPUT CURRENT, Io (A)

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

20 30 40 50 60 70 80 90

0 LFM

100 LFM

AMBIENT TEMPERATURE, TA OC

Figure 19. Derating Output Current versus Local Ambient

Temperature and Airflow (VIN = 12.0 Vdc, Vo=0.75Vdc).

Figure 22. Derating Output Current versus Local

Ambient Temperature and Airflow (VIN = 12 Vdc, Vo=5.0

Vdc).

OUTPUT CURRENT, Io (A)

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

20 30 40 50 60 70 80 90

0 LFM

100 LFM

AMBIENT TEMPERATURE, TA OC

Figure 20. Derating Output Current versus Local Ambient

Temperature and Airflow (VIN = 12.0Vdc, Vo=1.8 Vdc).

OUTPUT CURRENT, Io (A)

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

20 30 40 50 60 70 80 90

0 LFM

100 LFM

AMBIENT TEMPERATURE, TA OC

Figure 21. Derating Output Current versus Local Ambient

Temperature and Airflow (VIN = 12.0Vdc, Vo=3.3 Vdc).

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 10

Test Configurations

TO OSCILLOSCOPE

CURRENT PROBE

LTEST

1μH

BATTERY

CS 1000μF

Electrolytic

E.S.R.<0.1

@ 20°C 100kHz

2x100μF

Tantalum

VIN(+)

COM

NOTE: Measure input reflected ripple current with a simulated

source inductance (LTEST) of 1μH. Capacitor CS offsets

possible battery impedance. Measure current as shown

above.

CIN

Figure 23. Input Reflected Ripple Current Test Setup.

NOTE: All voltage measurements to be taken at the module

terminals, as shown above. If sockets are used then

Kelvin connections are required at the module terminals

to avoid measurement errors due to socket contact

resistance.

V

O

(+)

COM

1uF

.

RESISTIVE

LOAD

SCOPE

COPPER STRIP

GROUND PLANE

10uF

Figure 24. Output Ripple and Noise Test Setup.

VO

COM

VIN(+)

COM

RLOAD

Rcontact

Rdistribution

Rcontact

Rdistribution

Rcontact

Rdistribution

VIN

VO

NOTE: All voltage measurements to be taken at the module

terminals, as shown above. If sockets are used then

Kelvin connections are required at the module terminals

to avoid measurement errors due to socket contact

resistance.

Figure 25. Output Voltage and Efficiency Test Setup.



=

VO.

IO

VIN.

IIN

x

100

%

Efficiency

Design Considerations

Input Filtering

Austin MiniLynxTM 12V SIP module should be connected

to a low -impedance source. A highly inductive source

can affect the stability of the module. An input

capacitance must be placed directly adjacent to the

input pin of the module, to minimize input ripple voltage

and ensure module stability in the presence of inductive

traces that supply input voltage to the module.

In a typical application, a 22 µF low-ESR ceramic

capacitors will be sufficient to provide adequate ripple

voltage at the input of the module. To further minimize

ripple voltage at the input, additional ceramic

capacitors are recommended at the input of the

module. Figure 26 shows input ripple voltage (mVp-p)

for various outputs with a 10 µF or a 22µF input ceramic

capacitor at full load.

0

50

100

150

200

250

300

350

0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5

1 x 10uF

1 x 22uF

Figure 26. Input ripple voltage for various outputs

with 10 µF or a 22 µF ceramic capacitor at the input

(full-load).

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 11

Design Considerations (continued)

Output Filtering

The Austin MiniLynxTM 12 V SIP module is designed for low

output ripple voltage and will meet the maximum output ripple

specification with 1 µF ceramic and 10 µF tantalum capacitors

at the output of the module. However, additional output filtering

may be required by the system designer for a number of

reasons. First, there may be a need to further reduce the output

ripple and noise of the module. Second, the dynamic response

characteristics may need to be customized to a particular load

step change.

To reduce the output ripple and improve the dynamic response

to a step load change, additional capacitance at the output can

be used. Low ESR polymer and ceramic capacitors are

recommended to improve the dynamic response of the module.

For stable operation of the module, limit the capacitance to less

than the maximum output capacitance as specified in the

electrical specification table.

Safety Considerations

For safety agency approval the power module must be

installed in compliance with the spacing and separation

requirements of the end-use safety agency standards,

i.e., UL ANSI/UL* 62368-1 and CAN/CSA+ C22.2 No.

62368-1 Recognized, DIN VDE 0868-1/A11:2017

(EN62368-1:2014/A11:2017)

For the converter output to be considered meeting the

Requirements of safety extra-low voltage (SELV) or ES1,

the input must meet SELV/ES1 requirements. The power

module has extra-low voltage (ELV) outputs when all

inputs are ELV.

The input to these units is to be provided with a fast-

acting fuse with a maximum rating of 6A in the positive

input lead.

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 12

Feature Description

Remote On/Off

Austin MiniLynxTM 12V SIP power modules feature an On/Off pin

for remote On/Off operation. Two On/Off logic options are

available in the Austin MiniLynxTM 12V series modules. Positive

Logic On/Off signal, device code suffix “4”, turns the module ON

during a logic High on the On/Off pin and turns the module OFF

during a logic Low. Negative logic On/Off signal, no device code

suffix, turns the module OFF during logic High and turns the

module ON during logic Low.

For positive logic modules, the circuit configuration for using the

On/Off pin is shown in Figure 27. The On/Off pin is an open

collector/drain logic input signal (Von/Off) that is referenced to

ground. During a logic-high (On/Off pin is pulled high internal to

the module) when the transistor Q1 is in the Off state, the power

module is ON. Maximum allowable leakage current of the

transistor when Von/off = VIN,max is 10µA. Applying a logic-low

when the transistor Q1 is turned-On, the power module is OFF.

During this state VOn/Off must be less than 0.3V. When not

using positive logic On/off pin, leave the pin unconnected or tie

to VIN.

Q1

R2

R1 Q2

R3

R4

Q3 CSS

GND

VIN+

ON/OFF

PWM Enable

+

_

ON/OFF

V

ION/OFF

MODULE

Figure 27. Circuit configuration for using positive logic

On/OFF.

For negative logic On/Off devices, the circuit configuration is

shown is Figure 28. The On/Off pin is pulled high with an

external pull-up resistor (typical Rpull-up = 68k, +/- 5%). When

transistor Q1 is in the Off state, logic High is applied to the

On/Off pin and the power module is Off. The minimum On/off

voltage for logic High on the On/Off pin is 2.5 Vdc. To turn the

module ON, logic Low is applied to the On/Off pin by turning ON

Q1. When not using the negative logic On/Off, leave the pin

unconnected or tie to GND.

Q1

R1

R2

Q2 CSS

GND

PWM Enable

ON/OFF

VIN+

ON/OFF

_

+

V

I

MODULE

pull-up

R

ON/OFF

Figure 28. Circuit configuration for using negative

logic On/OFF.

Overcurrent Protection

To provide protection in a fault (output overload)

condition, the unit is equipped with internal

current-limiting circuitry and can endure current limiting

continuously. At the point of current-limit inception, the

unit enters hiccup mode. The unit operates normally

once the output current is brought back into its

specified range. The typical average output current

during hiccup is 3.5A.

Input Undervoltage Lockout

At input voltages below the input undervoltage lockout

limit, module operation is disabled. The module will

begin to operate at an input voltage above the

undervoltage lockout turn-on threshold.

Overtemperature Protection

To provide over temperature protection in a fault

condition, the unit relies upon the thermal protection

feature of the controller IC. The unit will shutdown if the

thermal reference point Tref2, (see Figure 31) exceeds

140oC (typical), but the thermal shutdown is not

intended as a guarantee that the unit will survive

temperatures beyond its rating. The module will

automatically restarts after it cools down.

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 13

Feature Descriptions (continued)

Output Voltage Programming

The output voltage of the Austin MiniLynxTM 12V can be

programmed to any voltage from 0.75Vdc to 5.5Vdc by

connecting a resistor (shown as Rtrim in Figure 29) between Trim

and GND pins of the module. Without an external resistor

between Trim and GND pins, the output of the module will be

0.7525Vdc. To calculate the value of the trim resistor, Rtrim for a

desired output voltage, use the following equation:













−

−

=1000

7525.0

10500

Vo

Rtrim

Rtrim is the external resistor in Ω

Vo is the desired output voltage

For example, to program the output voltage of the Austin

MiniLynxTM 12V module to 1.8V, Rtrim is calculated as follows:











−

−

=1000

7525.08.1

10500

Rtrim

= kRtrim 024.9

V

O

(+)

TRIM

GND

R

trim

LOAD

V

IN

(+)

ON/OFF

Figure 29. Circuit configuration to program output voltage

using an external resistor.

Table 1 provides Rtrim values required for some common output

voltages.

Table 1

VO, set (V)

Rtrim (KΩ)

0.7525

Open

1.2

22.46

1.5

13.05

1.8

9.024

2.5

5.009

3.3

3.122

5.0

1.472

Using 1% tolerance trim resistor, set point tolerance of ±2% is

achieved as specified in the electrical specification. The POL

Programming Tool, available at www.gecriticalpower.com under

the Design Tools section, helps determine the required external

trim resistor needed for a specific output voltage.

Voltage Margining

Output voltage margining can be implemented in the

Austin MiniLynxTM modules by connecting a resistor,

Rmargin-up, from the Trim pin to the ground pin for

margining-up the output voltage and by connecting a

resistor, Rmargin-down, from the Trim pin to the Output pin

for margining-down. Figure 30 shows the circuit

configuration for output voltage margining. The POL

Programming Tool, available at

www.gecriticalpower.com under the Design Tools

section, also calculates the values of Rmargin-up and

Rmargin-down for a specific output voltage and % margin.

Please consult your local GE technical representative for

additional details.

Vo

Austin Lynx or

Lynx II Series

GND

Trim

Q1

Rtrim

Rmargin-up

Q2

Rmargin-down

Figure 30. Circuit Configuration for margining Output

voltage.

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 14

Thermal Considerations

Power modules operate in a variety of thermal environments;

however, sufficient cooling should be provided to help ensure

reliable operation.

Considerations include ambient temperature, airflow, module

power dissipation, and the need for increased reliability. A

reduction in the operating temperature of the module will result

in an increase in reliability. The thermal data presented here is

based on physical measurements taken in a wind tunnel. The

test set-up is shown in Figure 32. Note that the airflow is parallel

to the long axis of the module as shown in figure 31. The

derating data applies to airflow in either direction of the

module’s long axis.

Tref2

Tref1

Airflow

Figure 31. Tref Temperature measurement location.

The thermal reference point, Tref used in the specifications is

shown in Figure 32. For reliable operation this temperature

should not exceed 115oC.

The output power of the module should not exceed the rated

power of the module (Vo,set x Io,max).

Please refer to the Application Note “Thermal Characterization

Process For Open-Frame Board-Mounted Power Modules” for a

detailed discussion of thermal aspects including maximum

device temperatures.

Figure 32. Thermal Test Set-up.

Heat Transfer via Convection

Increased airflow over the module enhances the heat

transfer via convection. Thermal derating curves

showing the maximum output current that can be

delivered by various module versus local ambient

temperature (TA) for natural convection and up to

0.5m/s (100 ft./min) are shown in the Characteristics

Curves section.

Air

flow

x

Power Module

Wind Tunnel

PWBs

5.97_

(0.235)

76.2_

(3.0)

Probe Location

for measuring

airflow and

ambient

temperature

25.4_

(1.0)

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 15

Post solder Cleaning and Drying

Considerations

Post solder cleaning is usually the final circuit-board assembly

process prior to electrical board testing. The result of inadequate

cleaning and drying can affect both the reliability of a power

module and the testability of the finished circuit-board

assembly. For guidance on appropriate soldering, cleaning and

drying procedures, refer to Board Mounted Power Modules:

Soldering and Cleaning Application Note.

Through-Hole Lead-Free Soldering

Information

The RoHS-compliant through-hole products use the SAC

(Sn/Ag/Cu) Pb-free solder and RoHS-compliant components.

They are designed to be processed through single or dual

wave soldering machines. The pins have an RoHS-compliant

finish that is compatible with both Pb and Pb-free wave

soldering processes. A maximum preheat rate of 3C/s is

suggested. The wave preheat process should be such that

the temperature of the power module board is kept below

210C. For Pb solder, the recommended pot temperature is

260C, while the Pb-free solder pot is 270C max. Not all

RoHS-compliant through-hole products can be processed

with paste-through-hole Pb or Pb-free reflow process. If

additional information is needed, please consult with your GE

technical representative for more details.

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 16

Mechanical Outline

Dimensions are in millimeters and (inches).

Tolerances: x.x mm  0.5 mm (x.xx in.  0.02 in.) [unless otherwise indicated]

x.xx mm  0.25 mm (x.xxx in  0.010 in.)

Top View

Side View

FUNCTION

1

Vo

2

Trim

3

GND

4

VIN

5

On/Off

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

July 24, 2020

Page 17

Recommended Pad Layout

Dimensions are in millimeters and (inches).

Tolerances: x.x mm  0.5 mm (x.xx in.  0.02 in.) [unless otherwise indicated]

x.xx mm  0.25 mm (x.xxx in  0.010 in.)

FUNCTION

1

Vo

2

Trim

3

GND

4

VIN

5

On/Off

GE

Data Sheet

12V Austin MiniLynxTM: SIP Non-Isolated DC-DC Power Modules

8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current

Contact Us

For more information, call us at

USA/Canada:

+1 888 546 3243, or +1 972 244 9288

Asia-Pacific:

+86-21-53899666

Europe, Middle-East and Africa:

+49.89.878067-280

Go.ABB/Industrial

GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no

liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s)

or information.

July 24, 2020

Version 1_4

Ordering Information

Please contact your GE Sales Representative for pricing, availability and optional features.

Table 2. Device Codes

Device Code

Input

Voltage

Output

Voltage

Output

Current

Efficiency

3.3V@ 3A

Connector

Type

Comcodes

AXA003A0XZ

8.3 – 14Vdc

0.75 – 5.5Vdc

3 A

91.0%

SIP

CC109101268

AXA003A0X4Z

8.3 – 14Vdc

0.75 – 5.5Vdc

3 A

91.0%

SIP

CC109104824

-Z refers to RoHS compliant Versions