DENSEI-LAMBDA ZWX180/L1 SPECIFICATIONS(1/2) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 A234-01-01/L1-A ( This specifications sheet also apply to other option model /L2.) MODEL ZWX180/L1 ITEMS V1 V2 V3 V4 V5 (5V SB) Nominal Output Voltage V +3.3 +5 +12 -12 +5 Minimum Output Current A 0 0 0 0 0 Maximum Output Current (Convection) A 6.0 5.0 6.0 0.2 1.4 W Maximum Output Power Each CH 19.8 25.0 72.0 2.4 7.0 (Convection) Combined 32W Total Output Power (Convection) W 90 Maximum Output Current (Forced Air) A 8.4 7.0 9.0 0.3 2.0 W Maximum Output Power Each CH 27.7 35.0 108.0 3.6 10.0 (Forced Air) Combined 54W Total Output Power (Forced Air) W 153 Peak Output Current (*1) A 12.0 10.0 13.0 0.3 2.0 W Peak Output Power Each CH (*1) 39.6 50.0 156.0 3.6 10.0 Combined 63W Total Peak Output Power (*1) W 180 Efficiency (100/200VAC )(Typ) (*2) 81%/84% Input Voltage Range (*4) 85-265VAC (47-63Hz) Input Current (100/200VAC) (Typ) (*2) 1.9A/1.0A Inrush Current (100/200VAC) (Typ) (*5) 14A/28A at Cold Start (Ta=25) PFHC Designed to meet IEC61000-3-2 Power Factor (100/200VAC )(Typ) (*2) 0.99/0.93 Output Voltage Accuracy % 5 5 5 5 5 Output Voltage Range Fixed Fixed Fixed Fixed Fixed Maximum Ripple & Noise -10<Ta<0C mV 160 180 180 160 160 (*3,*6) 0<Ta<50C mV 120 150 150 120 120 Maximum Line Regulation (*3,*6,*7) mV 20 48 48 20 20 Maximum Load Regulation (*3,*6,*8) mV 100 300 300 100 100 Over Current Protection (*9) A 8.827.359.450.322.1Over Voltage Protection V1 : 114%-130%(3.76-4.3V), V2 : 115%-140%(5.74-7V) (*10) V3 : 112%-130%(13.4-15.6V) Hold-up Time (Typ) (*2) 20ms at 100VAC Leakage Current (*3,*11) Less than 0.75mA Remote Sensing Possible (V1 only) ON/OFF Control (PS_ON) TTL compatible (H : Output Inhibit, L : Output Enable) : Designed to meet ATX standard. Series / Parallel Operation Operating Temperature (*12) -10 - +50C : 100%, 60C : 60%, 70C : 20% Operating Humidity 30 - 90%RH (No Dewdrop) Storage Temperature -30 - +85C Storage Humidity 10 - 95%RH (No Dewdrop) Cooling (*12) Convection Cooling / Forced air Cooling (System air Cooling) : 0.85 m3/min Withstand Voltage Input-FG : 2kVAC(20mA), Input-Output : 3kVAC(20mA) Output-FG : 500VAC(100mA) for 1min. Isolation Resistance More than 100M at 25C and 70%RH Output-FG : 500VDC Vibration At no operating 10 - 55Hz(Sweep for 1min) 19.6 m/s2 Constant, X,Y,Z 1hour each. 38 Shock - Less than 392 m/s 2 at no operating. 39 Safety - Approved by UL60950-1, CSA60950-1, EN60950-1, EN50178(OV II), Designed to meet DENAN (Section 2) at 100VAC only. Designed to meet EN55011/EN55022-B, FCC-ClassB, VCCI-B Designed to meet EN55011/EN55022-B, FCC-ClassB, VCCI-B 40 Conducted Emission 41 Radiated Emission (*3) (*3) - DENSEI-LAMBDA ZWX180/L1 SPECIFICATIONS(2/2) A234-01-02/L1 ( This specifications sheet also apply to other option model /L2.) MODEL ITEMS V1 42 Immunity 43 Weight (Typ.) 44 Size (W x H x D) V2 ZWX180/L1 V3 V4 V5 (5V SB) - Designed to meet IEC61000-4-2, -3, -4, -5, -6, -8, -11 g mm 700 98 x 45.5 x 240 ( Refer to Outline Drawing ) *Read instruction manual carefully, before using the power supply unit. =NOTE= *1. Operating time at peak output is less than 5sec. (Average output power and current are less than Maximum output power and current.) *2. At total output power (Forced air) (V1=6.5A, V2=6.5A, V3=7.7A, V4=0.2A, V5=1.0A), Ta=25C. *3. At total output power (Forced air). *4. For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 - 240VAC (50/60Hz). *5. Not applicable for the inrush current to Noise Filter for less than 0.2ms. *6. Please refer to Fig. A for measurement of line & load regulation and ripple voltage. *7. 85 - 265VAC , constant load. *8. No load-Full load, constant input voltage. *9. Avoid to operate at overload or short circuit condition for more than 30 seconds. V1,V2 and V3 : OCP circuit will shut down output except V5 with delay (more than 5s), manual reset (PS_ON reset or re power on.). V4 : Constant current limit with automatic recovery. V5 : Constant current limit in conjunction with all output with automatic recovery. *10. OVP circuit will shut down output, manual reset (PS_ON reset or re power on.). *11. Measured by the each measuring method of UL, CSA, EN and DENAN (at 60Hz), Ta=25C. *12. At forced air cooling, standard mounting. Refer to output derating curve.(A234-01-03_, A234-01-04_) P.S. 3.3V sense 150mm AWG18 Measuring Point for Ripple & Noise. A V1 C1 LOAD1 C6 COM Measure with EIAJ RC-9131 probe. A V2 C2 LOAD2 C7 Bandwidth of scope : 100MHz COM A V3 C3 C8 C4 C9 LOAD3 COM A COM LOAD4 V4 A V5 C5 C10 Capacitance LOAD5 COM Measuring Point for Vo and Line/Load Regulation. PS_ON COM Fig.A : Film Cap. 0.1 F C6,C7,C8,C9,C10 : Elec. Cap. 100 F C1,C2,C3,C4,C5