REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with N.O.R. 5962-R220-93. 93-08-26 M. A. FRYE B Changes in accordance with N.O.R. 5962-R153-94. 94-04-29 M. A. FRYE C Drawing updated to reflect current requirements. - ro 00-06-02 R. MONNIN THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK C. OFFICER STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216 CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE DRAWING APPROVAL DATE 92-03-13 REVISION LEVEL C MICROCIRCUIT, LINEAR, OPERATIONAL AMPLIFIER, WIDEBAND, FAST SETTLING, MONOLITHIC SILICON SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 1 OF 5962-87784 11 5962-E283-00 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87784 ~ ~ ~ ~ 01 C Device type (see 1.2.1) Case outline (see 1.2.2) ~ ~ ~ ~ Drawing number X ~ ~ ~ ~ ~ ~ ~ ~ Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 01 02 Circuit function HA-5190 EL-2190 Fast settling wideband operational amplifier Fast settling wideband operational amplifier 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter C X 2 Descriptive designator Terminals GDIP1-T14 or CDIP2-T14 See figure 1 CQCC1-N20 14 12 20 Package style Dual-in-line Can Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Voltage between +V and -V terminals ...................................35 V dc Differential input voltage .........................................................6.0 V dc Voltage at either input terminal ...............................................+V to -V Peak output current (< 10 % duty cycle)..................................50 mA Storage temperature range .....................................................-65qC to +150qC Maximum power dissipation (PD) 1/: Case C ................................................................................1.02 W Case X ................................................................................1.45 W Case 2 .................................................................................1.06 W Lead temperature (soldering, 10 seconds) .............................+275 qC Junction temperature (TJ) .......................................................+175 qC Thermal resistance, junction-to-case (TJC): Cases C and 2 ....................................................................See MIL-STD-1835 Case X ................................................................................82qC/W Thermal resistance, junction-to-ambient (TJA): Case C ................................................................................98qC/W Case X ................................................................................69qC/W Case 2 .................................................................................95qC/W 1/ Derate linearly above TA = +75qC as follows: case C at 10.2 qC/W, case X at 14.5qC/W, and case 2 at 10.6qC/W. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87784 A REVISION LEVEL C SHEET 2 1.4 Recommended operating conditions. Positive supply voltage range (+V) .........................................+12 V dc to +15 V dc Negative supply voltage range (-V) ........................................-12 V dc to -15 V dc Common mode input voltage (VCM) .......................................d |(+V - (-V)) / 2| Load resistance (RL) ...............................................................t 200 : Ambient operating temperature (TA) ......................................-55qC to +125qC 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 MIL-STD-973 MIL-STD-1835 - Test Method Standard Microcircuits. Configuration Management. Interface Standard For Microcircuit Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings (SMD's). Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87784 A REVISION LEVEL C SHEET 3 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535, appendix A. 3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87784 A REVISION LEVEL C SHEET 4 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55qC d TA d +125qC unless otherwise specified VIO VCM = 0 V, Group A subgroups Device type 1 01 Limits 2/ Min Input offset voltage +RS = 100 :, -RS = 100 : +IIB VCM = 0 V, +RS = 1.1 k:, 1 -RS = 100 : -IIB VCM = 0 V, +RS = 100 :, -RS = 1.1 k: Input offset current IIO VCM = 0 V, +RS = 1.1 k:, r6 -RS = 1.1 k: Common mode input voltage range Large signal voltage gain +VCM +V = 10 V, -V = -20 V -VCM +V = 20 V, -V = -10 V +AVOL VOUT = 0 V and 5.0 V, +CMRR 1 r15 2,3 r20 1,2,3 r4.0 All PA PA r6.0 All 5.0 V -5.0 1 VOUT = 0 V and -5.0 V, RL = 200 : Common mode rejection ratio r20 2,3 RL = 200 : -AVOL r15 All 2,3 1 mV r2 02 2,3 Input bias current Max r5 r10 2,3 1 Unit 'VCM = 5.0 V, +V = 10 V, All 15 2,3 5.0 1 15 2,3 5.0 1,2,3 All kV/V 74 dB -V = -20 V, VOUT = -5.0 V -CMRR 'VCM = -5.0 V, +V = 20 V, 74 -V = -10 V, VOUT = 5.0 V Output current +IOUT VOUT t -5.0 V, TA = +25qC -IOUT VOUT t 5.0 V, TA = +25qC 1 All 25 mA -25 See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87784 A REVISION LEVEL C SHEET 5 TABLE I. Electrical performance characteristics - Continued. Test Output voltage swing Symbol Conditions 1/ -55qC d TA d +125qC unless otherwise specified +VOUT RL = 200 : Group A subgroups Device type 1,2,3 All Min 5.0 +ICC 1,2,3 VOUT = 0 V, IOUT = 0 mA -ICC Power supply rejection ratio Slew rate Gain bandwidth 3/ 4/ product V 1,2,3 25 02 17 01 -25 02 -17 +V = 10 V and 20 V, -V = -15 V -PSRR -V = -10 V and -20 V, +V = +15 V +SR VOUT = -5.0 V to +5.0 V, 7 RL = 200 :, AV = +5 V/V 8 3/ 100 VOUT = +5.0 V to -5.0 V, 7 160 RL = 200 :, AV = +5 V/V 8 3/ 100 GBWP Max 01 +PSRR -SR Unit -5.0 -VOUT Quiescent power supply current Limits 2/ All 70 mA dB 70 VOUT d 200 mV, 4 All V/Ps 160 All 150 MHz fO = 100 kHz, RL = 1 k:, TA = +25qC VOUT d 200 mV, 150 fO = 1.0 MHz, RL = 1 k:, TA = +25qC Full power 3/ 5/ bandwidth FPBW VPK = 5.0 V, RL = 200 : 4 All 5.0 5,6 Closed loop stable 3/ gain Rise time 3/ 6/ MHz 4.0 CLSG RL = 200 :, CL d 10 pF 4,5,6 All tr VOUT = 0 V to +200 mV, 9 All RL = 200 :, AV = +5 V/V 10,11 5.0 V/V 18 ns 20 See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87784 A REVISION LEVEL C SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55qC d TA d +125qC unless otherwise specified tf Group A subgroups Device type VOUT = 0 V to -200 mV, 9 All RL = 200 :, AV = +5 V/V 10,11 VOUT = 0 V to +200 mV, 9,10,11 Limits 2/ Min Fall time 3/ 6/ Overshoot 3/ +OS Unit Max 18 ns 20 All 40 % RL = 200 :, AV = +5 V/V -OS 40 VOUT = 0 V to -200 mV, RL = 200 :, AV = +5 V/V Output resistance 3/ ROUT Open loop, TA = +25qC, 4 All 60 : 1,2,3 01 750 mW 02 510 All 200 AV = +5 V/V Quiescent power 7/ consumption Settling time 3/ PC ts VOUT = 0 V, IOUT = 0 mA 9 5 V step to 0.01 %, ns RL = 200 : 1/ +V = +15 V, -V = -15 V, RS = 100 :, RL = 500 k:, CL d 10 pF, VOUT = 0 V, and AV = +5 V/V unless otherwise specified. 2/ The limiting term "min" (minimum) and "max" (maximum) shall be considered to apply to magnitudes only. Negative current shall be defined as conventional current flow out of a device terminal. 3/ If not tested, shall be guaranteed to the limits specified in table I. 4/ Gain bandwidth product measured using open loop frequency response. 5/ Full power bandwidth = SR / ( 2 x S x VPK ). 6/ Rise and fall times measured between 10 % and 90 % point. 7/ Quiescent power consumption based on quiescent supply current test maximum (no load on outputs). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87784 A REVISION LEVEL C SHEET 7 Case X Letter A Ib ID ID1 e e1 F k k1 L Inches Min .130 .016 .585 .545 Millimeters Min Max 3.30 3.81 0.41 0.53 14.86 15.62 13.84 14.10 10.16 BSC 2.54 BSC 0.51 1.02 0.67 0.86 0.67 1.14 12.83 14.27 Max .150 .021 .615 .555 .400 BSC .100 BSC .020 .026 .026 .505 .040 .034 .045 .562 NOTES: 1. The US government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. 2. Pin numbers are for reference only and do not appear on package. 3. All leads - increase maximum limit by .003 (0.08 mm) when lead finish A or B is applied. FIGURE 1. Case outline. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87784 A REVISION LEVEL C SHEET 8 Device types 01 and 02 Case outlines C X 2 Terminal number 1 Terminal symbol NC NC NC 2 NC NC NC 3 NC NC NC 4 -INPUT NC NC 5 +INPUT -INPUT NC 6 -V +INPUT -INPUT 7 NC NC NC 8 NC NC +INPUT 9 NC NC -V 10 OUTPUT -V NC 11 +V OUTPUT NC 12 NC +V NC 13 NC --- NC 14 NC --- OUTPUT 15 --- --- NC 16 --- --- +V 17 --- --- NC 18 --- --- NC 19 --- --- NC 20 --- --- NC NC = No connection FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87784 A REVISION LEVEL C SHEET 9 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) TA = +125qC, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. (2) TA = +125qC, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87784 A REVISION LEVEL C SHEET 10 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) --- Final electrical test parameters (method 5004) 1*,2,3,4,5,6,7 Group A test requirements (method 5005) 1,2,3,4,5,6,7,8,9,10**,11** Groups C and D end-point electrical parameters (method 5005) 1 * PDA applies to subgroup 1. ** Subgroups 10 and 11 are guaranteed if not tested. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished in accordance with MIL-STD-973 using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0525. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone (614) 692-0674. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MILHDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-87784 A REVISION LEVEL C SHEET 11 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 00-06-02 Approved sources of supply for SMD 5962-87784 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-8778401CA 34371 HA1-5190/883 3/ EHA1-5190/883B 5962-8778401XA 3/ EHA2-5190/883B 5962-8778401XC 34371 HA2-5190/883 5962-87784012A 34371 HA4-5190/883 3/ EHA4-5190/883B 5962-8778402CA 3/ EL2190J/883B 5962-8778402XA 3/ EL2190G/883B 5962-87784022A 3/ EL2190L/883B 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number 34371 Vendor name and address Intersil Corporation P.O. Box 883 Melbourne, FL 32902-0883 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.