5962-87784012A - INTERSIL - Datasheet.Live

REVISIONS

LTR DESCRIPTION DATE (YR-MO-DA) APPROVED

A Changes in accordance with N.O.R. 5962-R220-93. 93-08-26 M. A. FRY E

B Changes in accordance with N.O.R. 5962-R153-94. 94-04-29 M. A. FRY E

C Drawing updated to reflect current requirements. - ro 00-06-02 R. MONNIN

THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.

REV

SHEET

REV

SHEET

REV STATUS REV CCCCCCCCCCC

OF SHEETS SHEET 1234567891011

PMIC N/A PREPARED BY

RICK C. OFFICER

DEFENSE SUPPLY CENTER COLUMBUS

STANDARD

MICROCIRCUIT

DRAWING

CHECKED BY

CHARLES E. BESORE COLUMBUS, OHIO 43216

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

APPROVED BY

MICHAEL A. FRYE MICROCI RCUIT, LINEAR, OPERATIONAL

AMPLIFI ER, WIDEBAND, FAST SETTLING,

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE

92-03-13 MONOLITHIC SILICON

AMSC N/A REVISION LEVELCSIZE

ACAGE CODE

67268 5962-87784

SHEET 1 OF 11

DSCC FORM 2233

APR 97 5962-E283-00

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

STANDARD

MICROCI RCUIT DRAWING

SIZE

A5962-87784

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000 REVISION LEVEL

CSHEET 2

DSCC FORM 2234

APR 97

1. SCOPE

1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in

accordance with MIL-PRF-38535, appendix A.

1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:

5962-87784 01 C X

~~~~

Drawing number Device type Case outline Lead finish

(see 1.2.1) (see 1.2.2) (see 1.2.3)

1.2.1 Device type(s). The device type(s) identify the circuit function as follows:

Device type Generic number Circuit function

01 HA-5190 Fast settling wideband operational amplifier

02 EL-2190 Fast settling wideband operational amplifier

1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:

Outline letter Descriptive designator Terminals Package style

C GDIP1-T14 or CDIP2-T14 14 Dual-in-line

X See figure 1 12 Can

2 CQCC1-N20 20 Square leadless chip carrier

1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.

1.3 Absolute maximum ratings.

Voltage between +V and –V terminals ...................................35 V dc

Differential input voltage .........................................................6.0 V dc

Voltage at either input terminal ...............................................+V to –V

Peak output current (< 10 % duty cycle)..................................50 mA

Storage temperature range .....................................................-65

C to +150

Maximum power dissipation (PD) 1/:

Case C ................................................................................1.02 W

Case X ................................................................................1.45 W

Case 2 .................................................................................1.06 W

Lead temperature (soldering, 10 seconds) .............................+275

Junction temperature (TJ) .......................................................+175

Thermal resistance, junction-to-case (

JC):

Cases C and 2 ....................................................................See MIL-STD-1835

Case X ................................................................................82

C/W

Thermal resistance, junction-to-ambient (

JA):

Case C ................................................................................98

C/W

Case X ................................................................................69

C/W

Case 2 .................................................................................95

C/W

1/ Derate linearly above TA = +75

C as follows: case C at 10.2

C/W, case X at 14.5

C/W, and case 2 at 10.6

C/W.

STANDARD

MICROCI RCUIT DRAWING

SIZE

A5962-87784

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000 REVISION LEVEL

CSHEET 3

DSCC FORM 2234

APR 97

1.4 Recommended operating conditions.

Positive supply voltage range (+V) .........................................+12 V dc to +15 V dc

Negative supply voltage range (-V) ........................................-12 V dc to –15 V dc

Common mode input voltage (VCM) .......................................

|(+V – (-V)) / 2|

Load resistance (RL) ...............................................................

200

Ambient operating temperature (TA) ......................................-55

C to +125

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a

part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed

in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in

the solicitation.

SPECIFICATION

DEPARTMENT OF DEFENSE

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

STANDARDS

DEPARTMENT OF DEFENSE

MIL-STD-883 - Test Method Standard Microcircuits.

MIL-STD-973 - Configuration Management.

MIL-STD-1835 - Interface Standard For Microcircuit Case Outlines.

HANDBOOKS

DEPARTMENT OF DEFENSE

MIL-HDBK-103 - List of Standard Microcircuit Drawings (SMD's).

MIL-HDBK-780 - Standard Microcircuit Drawings.

(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization

Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-

JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer

Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-

PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying

activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan

may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.

These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-

PRF-38535 is required to identify when the QML flow option is used.

STANDARD

MICROCI RCUIT DRAWING

SIZE

A5962-87784

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000 REVISION LEVEL

CSHEET 4

DSCC FORM 2234

APR 97

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as

specified in MIL-PRF-38535, appendix A and herein.

3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full ambient operating temperature range.

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are described in table I.

3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN

listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For

packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the

option of not marking the "5962-" on the device.

3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an

approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to

listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-

38535, appendix A and the requirements herein.

3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided

with each lot of microcircuits delivered to this drawing.

3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,

appendix A.

3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's

facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the

reviewer.

STANDARD

MICROCI RCUIT DRAWING

SIZE

A5962-87784

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000 REVISION LEVEL

CSHEET 5

DSCC FORM 2234

APR 97

TABLE I. Electrical performance characteristics.

Test Symbol

Conditions 1/

-55

+125

unless otherwise specified Group A

subgroups Device

type Limits 2/ Unit

Min Max

Input offset voltage VIO VCM = 0 V, 101

+RS = 100

, -RS = 100

2,3

102

2,3

Input bias current +IIB VCM = 0 V, +RS = 1.1 k

,1All

-RS = 100

2,3

-IIB VCM = 0 V, +RS = 100

-RS = 1.1 k

2,3

Input offset current IIO VCM = 0 V, +RS = 1.1 k

,1All

4.0

-RS = 1.1 k

2,3

6.0

Common mode input

voltage range +VCM +V = 10 V, -V = -20 V 1,2,3 All 5.0 V

-VCM +V = 20 V, -V = -10 V -5.0

Large signal voltage

gain +AVOL VOUT = 0 V and 5.0 V, 1All15 kV/V

= 200

2,3 5.0

-AVOL VOUT = 0 V and –5.0 V, 115

= 200

2,3 5.0

Common mode rejection

ratio +CMRR

VCM = 5.0 V, +V = 10 V,

-V = -20 V, VOUT = -5.0 V

1,2,3 All 74 dB

-CMRR

VCM = -5.0 V, +V = 20 V,

-V = -10 V, VOUT = 5.0 V

Output current +IOUT VOUT

-5.0 V, TA = +25

C1All25 mA

-IOUT VOUT

5.0 V, TA = +25

C-25

See footnotes at end of table.

STANDARD

MICROCI RCUIT DRAWING

SIZE

A5962-87784

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000 REVISION LEVEL

CSHEET 6

DSCC FORM 2234

APR 97

TABLE I. Electrical performance characteristics – Continued.

Test Symbol

Conditions 1/

-55

+125

unless otherwise specified Group A

subgroups Device

type Limits 2/ Unit

Min Max

Output voltage swing +VOUT RL = 200

1,2,3 All 5.0 V

-VOUT -5.0

Quiescent power supply

current +ICC VOUT = 0 V, IOUT = 0 mA 1,2,3 01 25 mA

02 17

-ICC 01 -25

02 -17

Power supply rejection

ratio +PSRR +V = 10 V and 20 V,

-V = -15 V 1,2,3 All 70 dB

-PSRR -V = -10 V and –20 V,

+V = +15 V 70

Slew rate +SR VOUT = -5.0 V to +5.0 V, 7 All 160 V/

RL = 200

, AV = +5 V/V 8 3/ 100

-SR VOUT = +5.0 V to –5.0 V, 7 160

RL = 200

, AV = +5 V/V 8 3/ 100

Gain bandwidth 3/ 4/

product GBWP VOUT

200 mV,

fO = 100 kHz, RL = 1 k

TA = +25

4 All 150 MHz

VOUT

200 mV,

fO = 1.0 MHz, RL = 1 k

TA = +25

150

Full power 3/ 5/

bandwidth FPBW VPK = 5.0 V, RL = 200

4All5.0 MHz

5,6 4.0

Closed loop stable 3/

gain CLSG RL = 200

, CL

10 pF 4,5,6 All 5.0 V/V

Rise time 3/ 6/ trVOUT = 0 V to +200 mV, 9 All 18 ns

RL = 200

, AV = +5 V/V 10,11 20

See footnotes at end of table.

STANDARD

MICROCI RCUIT DRAWING

SIZE

A5962-87784

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000 REVISION LEVEL

CSHEET 7

DSCC FORM 2234

APR 97

TABLE I. Electrical performance characteristics – Continued.

Test Symbol

Conditions 1/

-55

+125

unless otherwise specified Group A

subgroups Device

type Limits 2/ Unit

Min Max

Fall time 3/ 6/ tfVOUT = 0 V to –200 mV, 9 All 18 ns

RL = 200

, AV = +5 V/V 10,11 20

Overshoot 3/ +OS VOUT = 0 V to +200 mV,

RL = 200

, AV = +5 V/V

9,10,11 All 40 %

-OS VOUT = 0 V to –200 mV,

RL = 200

, AV = +5 V/V

Output resistance 3/ ROUT Open loop, TA = +25

AV = +5 V/V

4All 60

Quiescent power 7/

consumption PCVOUT = 0 V, IOUT = 0 mA 1,2,3 01 750 mW

02 510

Settling time 3/ ts5 V step to 0.01 %,

RL = 200

9 All 200 ns

1/ +V = +15 V, -V = -15 V, RS = 100

, RL = 500 k

, CL

10 pF, VOUT = 0 V, and AV = +5 V/V unless otherwise specified.

2/ The limiting term “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Negative

current shall be defined as conventional current flow out of a device terminal.

3/ If not tested, shall be guaranteed to the limits specified in table I.

4/ Gain bandwidth product measured using open loop frequency response.

5/ Full power bandwidth = SR / ( 2 x

x VPK ).

6/ Rise and fall times measured between 10 % and 90 % point.

7/ Quiescent power consumption based on quiescent supply current test maximum (no load on outputs).

STANDARD

MICROCI RCUIT DRAWING

SIZE

A5962-87784

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000 REVISION LEVEL

CSHEET 8

DSCC FORM 2234

APR 97

Case X

Letter Inches Millimeters

Min Max Min Max

A .130 .150 3.30 3.81

b.016 .021 0.41 0.53

D.585 .615 14.86 15.62

D1 .545 .555 13.84 14.10

e .400 BSC 10.16 BSC

e1 .100 BSC 2.54 BSC

F .020 .040 0.51 1.02

k .026 .034 0.67 0.86

k1 .026 .045 0.67 1.14

L .505 .562 12.83 14.27

NOTES: 1. The US government preferred system of measurement is the metric SI system. However, since this item was

originally designed using inch-pound units of measurement, in the event of conflict between the metric

and inch-pound units, the inch-pound units shall take precedence.

2. Pin numbers are for reference only and do not appear on package.

3. All leads – increase maximum limit by .003 (0.08 mm) when lead finish A or B is applied.

FIGURE 1. Case outline.

STANDARD

MICROCI RCUIT DRAWING

SIZE

A5962-87784

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000 REVISION LEVEL

CSHEET 9

DSCC FORM 2234

APR 97

Device types 01 and 02

Case outlines C X 2

Terminal

number Terminal symbol

1 NCNCNC

2 NCNCNC

3 NCNCNC

4 -INPUT NC NC

5 +INPUT -INPUT NC

6 -V +INPUT -INPUT

7 NCNCNC

8 NC NC +INPUT

9NCNC-V

10 OUTPUT -V NC

11 +V OUTPUT NC

12 NC +V NC

13 NC --- NC

14 NC --- OUTPUT

15 --- --- NC

16 --- --- +V

17 --- --- NC

18 --- --- NC

19 --- --- NC

20 --- --- NC

NC = No connection

FIGURE 2. Terminal connections.

STANDARD

MICROCI RCUIT DRAWING

SIZE

A5962-87784

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000 REVISION LEVEL

CSHEET 10

DSCC FORM 2234

APR 97

4. QUALITY ASSURANCE PROVISIONS

4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,

appendix A.

4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices

prior to quality conformance inspection. The following additional criteria shall apply:

a. Burn-in test, method 1015 of MIL-STD-883.

(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision

level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall

specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in

test method 1015 of MIL-STD-883.

(2) TA = +125

C, minimum.

b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter

tests prior to burn-in are optional at the discretion of the manufacturer.

4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of

MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply.

4.3.1 Group A inspection.

a. Tests shall be as specified in table II herein.

4.3.2 Groups C and D inspections.

a. End-point electrical parameters shall be as specified in table II herein.

b. Steady-state life test conditions, method 1005 of MIL-STD-883.

(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision

level control and shall be made available to the preparing or acquiring activity upon request. The test circuit

shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent

specified in test method 1005 of MIL-STD-883.

(2) TA = +125

C, minimum.

(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.

5. PACKAGING

5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.

STANDARD

MICROCI RCUIT DRAWING

SIZE

A5962-87784

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000 REVISION LEVEL

CSHEET 11

DSCC FORM 2234

APR 97

TABLE II. Electrical test requirements.

MIL-STD-883 test requirements Subgroups

(in accordance with

MIL-STD-883, method 5005,

table I)

Interim electrical parameters

(method 5004) ---

Final electrical test parameters

(method 5004) 1*,2,3,4,5,6,7

Group A test requirements

(method 5005) 1,2,3,4,5,6,7,8,9,10**,11**

Groups C and D end-point

electrical parameters

(method 5005)

* PDA applies to subgroup 1.

** Subgroups 10 and 11 are guaranteed if not tested.

6. NOTES

6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications

(original equipment), design applications, and logistics purposes.

6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a

contractor-prepared specification or drawing.

6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for

the individual documents. This coordination will be accomplished in accordance with MIL-STD-973 using DD Form 1692,

Engineering Change Proposal.

6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application

requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for

coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962)

should contact DSCC-VA, telephone (614) 692-0525.

6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone

(614) 692-0674.

6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-

HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted

by DSCC-VA.

STANDARD MICROCIRCUIT DRAWI NG BULLETIN

DATE: 00-06-02

Approved sources of supply for SMD 5962-87784 are listed below for immediate acquisition information only and

shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be

revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a

certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next

dated revision of MIL-HDBK-103 and QML-38535.

Standard

microcircuit drawing

PIN 1/

Vendor

CAGE

number

Vendor

similar

PIN 2/

5962-8778401CA 34371 HA1-5190/883

3/ EHA1-5190/883B

5962-8778401XA 3/ EHA2-5190/883B

5962-8778401XC 34371 HA2-5190/883

5962-87784012A 34371 HA4-5190/883

3/ EHA4-5190/883B

5962-8778402CA 3/ EL2190J/883B

5962-8778402XA 3/ EL2190G/883B

5962-87784022A 3/ EL2190L/883B

1/ The lead finish shown for each PIN representing a hermetic

package is the most readily available from the manufacturer

listed for that part. If the desired lead finish is not listed

contact the vendor to determine its availability.

2/ Caution. Do not use this number for item acquisition.

Items acquired to this number may not satisfy the

performance requirements of this drawing.

3/ Not available from an approved source of supply.

Vendor CAGE Vendor name

number and address

34371 Intersil Corporation

P.O. Box 883

Melbourne, FL 32902-0883

The information contained herein is disseminated for convenience only and the

Government assumes no liability whatsoever for any inaccuracies in the

information bulletin.